how to change a starter on a chevy uplander

You search PDF repair manual about how to change a starter on a chevy uplander, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to change a starter on a chevy uplander Direct Download speed 5432 Kb/s

  how to change a starter on a chevy uplander Full Version speed 8172 Kb/s



2002 Honda RSX Starter Removal and Installation Manual

0

Filed Under (Honda Manuals) by admin on 17-05-2011

download
Removal 1. Make sure you have the anti-theft codes for the radio, then write down the customer’s radio station presets. 2. Disconnect the negative cable from the battery first, then disconnect the positive cable. 3. Disconnect the knock sensor connector. 4. K20A3 engine: Disconnect the bolt securing the harness bracket. 5. K20A2, K20Z1 engines: Remove the front subframe damper. 6. K20A2, K20Z1 engines: Remove the bolt (A) securing the harness bracket, then remove the intake manifold brackets (B) 7. Disconnect the starter cable (A) from the B terminal on the solenoid, then disconnect the BLK/WHT wire (B) from the S terminal. 8. Remove the two bolts holding the starter, then remove the starter. K20A3 engine K20A2, K20Z1 engines Installation 1. Install the two bolts holding the starter. 2. Connect the starter cable (A) from the B terminal on the solenoid, then connect the BLK/WHT wire (B) from the S terminal. Make sure the crimped side of the ring terminal is facing out. K20A3 engine K20A2, K20Z1 engines 3. K20A2, K20Z1 engines: Install the bolt (A) securing the harness bracket, then Install the intake manifold brackets (B) 4. K20A2, K20Z1 engines: Install the front subframe damper. 5. K20A3 engine: Connect the bolt securing the harness bracket. 6. Connect the knock sensor connector. 7. Connect the positive cable to the battery first, then connect the negative cable. 8. Start the engine to make sure the starter operates properly. 9. Enter the anti-theft codes for the radio, then enter the customer’s radio station presets. 10. Set the clock. 11.2002-2004 models: Do the engine control module (ECM) /powertrain control module (PCM) idle learn procedure. 12. Do the power window control unit reset procedure.

Related Content:

2006 chevrolet cobalt starter removal instructions, 05 kia sedona starter bolts, 2002 chevy impala starter repla, 2002 chevy impala starter replacement, how do you change a starter on a 2002 chevy impala, how to replace a starter on a 2001 mitsubishi diamante, kia sorento starter motor diagram, replacing starter on 2002 impala

Ford SVT Contour/ Mercury 2.5L V-6 Cougar (5 Speed Manual Transmission Only) Supercharger System Installation Manual

0

Filed Under (Ford Manuals) by admin on 24-05-2012

download
1998-2000 FORD SVT CONTOUR/ MERCURY 2.5L V-6 COUGAR Installation Instructions For best performance and continued durability, please take note of the following key points: 1. Use only premium grade fuel 92 octane or higher (R+M/2). 2. The engine must have stock compression ratio. 3. If the engine has been modified in any way, check with Vortech prior to using this product. 4. Always listen for any sign of detonation (pinging) and discontinue hard use (no boost) until problem is resolved. 5. Perform an oil and filter change upon completion of this installation and prior to test driving your vehicle. Thereafter, always use a high grade SF rated engine oil or a high quality synthetic, and change the oil and filter every 3,000 miles or less. Never attempt to extend the oil change interval beyond 3,000 miles, regardless of oil manufacturer’s claims as potential damage to the supercharger may result. 6. Before beginning installation, replace all spark plugs that are older than 1 year or 10,000 miles with original heat range plugs as specified by the manufacturer and reset timing to factory specifications (follow the procedures indicated within the factory repair manual and/or as indicated on the factory underhood emissions tag). Do not use platinum spark plugs unless they are original equipment. Change spark plugs at least every 20,000 miles and spark plug wires at least every 50,000 miles. TOOL & SUPPLY REQUIREMENTS: •Factory Repair Manual •3/8″ Socket and Drive Set: SAE & Metric •1/2″ Socket and Drive Set: SAE & Metric •3/8″ NPT Tap and Handle •Adjustable Wrench •Open End Wrenches: 3/8″, 7/16″, 1/2″, 9/16″ •Center Punch •Ford Springlock 3/8″ Fuel Fitting Disconnect Tool •5 Quarts SH/CF Rated Quality Engine Oil •Oil Filter and Wrench •Flat #2 Screwdriver •Phillips #2 Screwdriver •Heavy Grease •Silicone Sealer •Drill Motor •1/8″, 3/16″, 27/64″ Drill Bits •9/16″ Rota Broach Tool (also available from Vortech) •Molylube •Wire Strippers and Crimpers •Utility Knife If your vehicle has in excess of 10,000 miles since its last spark plug change, then you will also need: •Spark Plug Socket •NEW Spark Plugs

Related Content:

free repair manual for 1998 Ford Contour SVT, repair manual for 1998 Ford Contour SVT, 97 Ford Thunderbird Repair Manual, 98 contour svt 2 5 alternator diagram, downloadable owners manual 1998 ford contour, Ford five hundred spark plug change, how to change thermostat on a 1998 ford contour, ou change the antifreeze in a 2008 G6 3 9, wheelbearing keeps wearing out 98 Camry

1995 Toyota 4Runner STARTING AND CHARGING SYSTEMS REPAIR MANUAL

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
TROUBLE SHOOTING NOTE: See TROUBLE SHOOTING – BASIC PROCEDURES article in GENERAL INFORMATION. 1) If a no-start condition exists and battery is known to be good, connect test light or voltmeter between starter solenoid terminal No. 50 and ground. See Figs. 6 and 7. 2) Turn ignition switch to START position. If test light or voltmeter does not indicate voltage, check main fusible links and large ampere main fuses in engine compartment relay box. If fusible links and fuses are okay, see IGNITION SWITCH CONTINUITY TEST and/or STARTER RELAY TEST under ON-VEHICLE TESTING. ON-VEHICLE TESTING NOTE: Before testing, ensure battery is fully charged, battery cables and terminal ends are tight and clean, and engine grounds are secure. CLUTCH START SWITCH TEST 1) Switch is located above clutch pedal on bracket. Disconnect wiring harness connector from switch. 2) Connect ohmmeter probes to switch terminals. Depress clutch pedal. If continuity does not exist, adjust or replace clutch start switch. If continuity exists, check circuit to starter relay for open, and check starter relay. See STARTER RELAY TEST. CLUTCH START CANCEL SWITCH TEST 1) Locate switch in left dash panel. Remove right lower instrument panel to access switch connector. Disconnect wiring harness connector from switch pigtail connector. See Fig. 1. 2) Connect negative lead of ohmmeter to terminal No. 1. Ensure continuity does not exist between connector terminals No. 1 and 2, terminals No. 1 and 3, and terminals No. 2 and 3. Check operation of switch by connecting jumper wires from 12-volt battery. Connect positive lead to terminal No. 3 and negative battery lead to terminal No. 1. 3) Using ohmmeter, ensure continuity does not exist between connector terminals No. 1 and 2 until switch button is pushed. When switch button is pushed, switch light should come on and continuity should exist. Disconnect battery and ensure continuity does not exit between terminals No. 1 and 2. If switch does not test as specified, replace switch. Fig. 1: Identifying Clutch Start Cancel Switch Connector Terminals Courtesy of Toyota Motor Sales, U.S.A., Inc. IGNITION SWITCH CONTINUITY TEST WARNING: Deactivate air bag system before performing any service operation. For 1996 4Runner, see AIR BAG RESTRAINT SYSTEM article. 1995 1) Disconnect negative battery cable. Removedriver’s lower instrument panel cover. Remove upper and lower steering column covers if needed. Locate ignition switch wiring harness 8-pin connector. See Figs. 2-3. 2) With ignition switch in LOCK position, there should be no continuity between any terminals. With ignition switch in ACC position, there should be continuity between terminals No. 2 and 3. With ignition switch in ON position, there should be continuity between terminals No. 1, 2 and 3, and between terminals No. 7 and 8. 3) With ignition switch in START position, there should be continuity between terminals No. 1, 4 and 6, and between terminals No. 7 and 8. If continuity is not as specified, replace switch.

Related Content:

how do i install ignition switch on 1996 chevy pickup, how to replace a 1990 Toyota Corolla Ignition switch, g6 testing key switch, 2007 chevy silverado brake switch installation, what causes 2005 toyota sienna starter relay to burn out, how to take ignition switch out of kia sorento, how toremuve thh ignition key on chrysler 2002 concord LX1 or baypass, ignition switch removal on 2003 buick century, ignition switch wiring diagram 2006 chevrolet uplander, where is ignition switch 01 silverado

1994 Chevy Truck C 1500 Truck 2WD Tune-up and Engine Performance Checks/ Ignition-Timing Connector Location Change Manual

0

Filed Under (Chevy Manuals) by admin on 06-05-2012

download
SUBJECT: TIMING CONNECTOR LOCATION CHANGE MODELS: 1994 CHEVROLET AND GMC C/K TRUCKS WITH GASOLINE ENGINES The timing connector, which can be disconnected to return engine timing to base for adjustment purposes, has been moved from the engine compartment to inside the cab. This new location is not currently reflected in the Service or Owner’s Manual. The new location is under the dash directly below the glove compartment. The tan/black wire is routed for a short distance outside of a large wiring harness. This large harness is routed between the heater blower motor and evaporator case. The timing connector is taped to the wire bundle (Figure 1)

Related Content:

99 F150 C202, 1994 chevy truck electrical troubleshooting, mlps wire configuration for 1994 f150, pdf 1994 chevrolet chevy van 1500 repair manual

2005 TOYOTA AVALON TVIP V4 (REMOTE ENGINE STARTER) INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 26-03-2012

download
TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 2 of 33 pages Issue: C 02/02/05 Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Visassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Vehicle Disassembly. (a) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. (2) Do not touch the positive terminal with any tool removing the cable. (b) Remove the glove box under-dash cover. (Fig. 1-2) (c) Remove the passenger’s step cover. (Fig. 1-3) Fig. 1-1 10mm Wrench Negative Battery Cable Battery Step Cover Fig. 1-3 Nylon Panel Removal Tool Fig. 1-2 Under-Dash Cover Nylon Panel Removal Tool TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 3 of 33 pages Issue: C 02/02/05 (d) Remove the passenger’s cowl cover. (Fig. 1-4) (1) Remove one nut securing the cowl cover. (e) Remove one screw and one bolt from the glove box assembly. (Fig. 1-5) (f) Remove the glove box assembly. (Fig. 1-6) (1) Open the glove box door and remove three screws securing the glove box assembly. (2) Disconnect the trunk opener cancel switch from the glove box assembly if equipped. For vehicles with Smart Entry, the disassembly process ends on Step f. Go to Section 5. For vehicles without Smart Entry, continue the disassembly process. FOR VEHICLES WITHOUT SMART ENTRY SYSTEM ONLY. (Step g) NOTE: Do not perform this step if the vehicle has Smart Entry. (g) Remove the driver’s step cover. (Fig. 1-7) Screw Fig. 1-5 10mm Wrench, Phillips Screwdriver Bolt Glove Box Assembly Cowl Cover Fig. 1-4 Nut Fig. 1-6 Nylon Panel Removal Tool, Phillips Screwdriver Screws (x3) Glove Box Assembly Trunk Opener Cancel Switch Connector Fig. 1-7 Step Cover Nylon Panel Removal Tool
TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 4 of 33 pages Issue: C 02/02/05 FOR VEHICLES WITHOUT SMART ENTRY SYSTEM ONLY. (Steps h-l) NOTE: Do not perform this step if the vehicle has Smart Entry. (h) Remove the driver’s cowl cover. (Fig. 1-8) (1) Remove the one nut securing the cowl cover. (i) Remove the hood release cable. (Fig. 1-9) (1) Do not bend the hood release cable. (j) Open the screw cover on the lower dash cover. Insert the tip of a Nylon Panel Removal Tool in the upper slot to loosen it. (Fig. 1-9) (1) Remove one screw and one bolt securing the lower dash cover. (k) Remove the lower dash cover. (Fig. 1-10) (1) Disconnect the temperature sensor (connector and aspirator hose) from the lower dash cover if equipped. (l) Carefully remove the driver side airbag assembly. (Fig. 1-11) (1) Remove four bolts securing the driver side airbag assembly. (2) Be careful not to get cut by the sharp metal edges. (3) Do not disconnect the airbag assembly. (4) Use the empty V4 kit box to support the airbag assembly on the floor

Related Content:

Prius upper glovebox door hinge, Prius repair glovebox door, toyota venza glove compartment box, how to take the back off a blu dask 3 5, colbalt where is the strarter located, 2005 toyota tacoma airbag fuse location, 2005 toyota corolla under carriage, clicking noise by glove box 2008 chevy impala, loud clicking noise in glove box impala, PICTURE OF GLOVE BOX LOWER BRACE ON CHEVY UPLANDER

TOYOTA G52, G54, W56 & G58 (AX5) 5 SPEED TRANS. TO CHEVY AND BUICK ENGINES INSTALLATION INSTRUCTIONS:

0

Filed Under (Toyota Manuals) by admin on 10-11-2011

download
This bellhousing is not compatible with transmissions that were previously equipped with diesel engines. The bellhousing design incorporates a special modified clutch release lever and a Toyota Land Cruiser slave cylinder. We have provided slave cylinder mounting on the passenger side of the bellhousing and have incorporated a new push rod location that will provide a quick short travel of the clutch release mechanism. The kit does not include the Toyota Land Cruiser slave cylinder, Part No. 31470-60022. The bellhousing is designed for the 153 tooth flywheel application. If your block is equipped with a 168 tooth flywheel, you will be required to use a high torque starter without a nose cone to fit the bellhousing (P/N 22-0001). The bellhousing is compatible with the Buick flywheel that has 160 teeth. A slight modification may be required in the starter pocket area when using the Buick installation. The inside of the bellhousing uses a high profile Centerforce diaphragm clutch assembly. By using this pressure plate, you can be sure that the slave cylinder travel will be appropriate for obtaining a maximum clutch release. The release bearing, Part No. N1430, is a standard flat faced Chevy release bearing. The bearing must not have continual contact with the fingers of the clutch. Adjust the length of your push rod for clearance between the fingers and the face of bearing. In order to adjust the height of the release bearing, we recommend that you install the new bellhousing over the clutch assembly and onto the engine prior to assembling the transmission to the bellhousing. By doing this procedure, you will be able to install the clutch release lever, slave cylinder, slave cylinder push rod, and release bearing directly to the clutch assembly. The reason this is necessary is that there are variations as to the thickness of the flywheel which either raise or lower the fingers of the clutch as related to the release bearing. The push rod of the slave cylinder can be adjusted, to obtain the necessary clearance between the release bearing and clutch fingers. If the bearing is permitted continual contact on the fingers, then you will have premature release bearing failure. We do not furnish a rubber boot for the area between the bellhousing and clutch arm since it is too restrictive for the clutch arm movement. We believe that the location of the opening is such that any dust or other debris will have a hard time accessing the opening. If you anticipate water hazards, we would recommend a small rubber flapper that could be screwed to the outside of the bellhousing.

Related Content:

buick lesabre2005hood knob, Adjust clutch on 2005 PT cruiser, how much to fit a clutch in a landcruiser, removing push rods N14, replaced clutch now soft will it tighten toyota fj, w56 fix

2007 Toyota Camry equipped with the Smart Key System with Push Button Start Remote Starter Integration

0

Filed Under (Toyota Manuals) by admin on 20-05-2011

download
Material required: – Remote Car Starter – Xpresskit : XK05-PKT2 or Bypasskit :PKT2 – One 5-wire relay for auto lamp circuit Key required for programming: 1 Average installation time: 2.5 hours Difficulty level: Medium 2.0 Preparation: -Remove the driver’s side under dash, as well as the knee airbag bolts. Move the Airbag aside, but DO NOT DISCONNECT the Airbag connector in order to avoid setting any vehicle codes. -Remove the driver’s side floor heating duct, in order to access the vehicle IMI & IMO wires easily. 3.0 Installation: The remote car starter will be installed in a conventional manner even if the car is equipped with the Smart Key “Push-to-Start” system. 3.01 Main Ignition Harness Connection: Most of the connections will be done behind the Fuse box. This fuse box is located under the driver side underdash. Also, the vehicle’s TACH wire can be found inside vehicle, as per diagram below and it is suggested to use this wire for the remote start tach source. The remote start hood pin switch wire is the only wire which must be run into the engine compartment for safety. Accessory (+): White Ignition 1 (+): Pink Ignition 2 (+): Light Green Starter (+): Grey Tach: Black 3.02 Wiring location for the Bypasskit XK-05 PKT2: The connection for the XK05-PKT2 will be done on the driver side under dash. The wires required are from a 5 wires harness coming from behind the heater module, high above the gas pedal near the firewall. The five wires in this harness are as follows: Blue: transponder IMI (Immobilizer in) wire, which gets cut in two and wired in series. The bottom-half wire connects to the kits Violet/White wire and the top-half wire connects the kits Violet wire. Green: transponder IMO (Immobilizer out) wire, which gets wired in parallel with the kits Orange wire. White/Black, White & Orange… these wire are not used for installation The GREEN LED output wire from the XK05-PKT2 is not required for this installation. The vehicle LED does come on during remote start. 3.03 Wiring location for door locks and factory alarm control: The wires to control the factory alarm and the door locks are located behind the driver’s kick panel. These wires must receive negative pulses. It is mandatory to disarm the OEM alarm system before remote start sequence Grey Unlock Wire : A double pulse unlock (-) output is required to disarm and unlock all doors. The first unlock (-) pulse disarms OEM alarm and unlocks driver’s door, the second pulse will unlock all other doors. In order to disarm the OEM alarm when remote starting, this GREY wire requires a pulse before start, which unlocks the driver’s door. So, if the remote systems unlock output does offer a pulse before start, then connect both the unlock and disarm (-) output wires to the vehicle’s GREY unlock wire. Brown Lock Wire : In order to lock and arm the OEM alarm system a (-) pulse is required for the vehicle’s BROWN lock wire. If the vehicle’s ignition on the alarm will not arm, if locking with remote.

Related Content:

2007 camry speed sensor wire burn under dash, 2007 dts electrical problem no start or cranking alarm not working, 2007 impala starter problems, 2007 toyota camry key broke, how to install XT-016C fog lights 2011 camry, smart kye push waring diagram 2007, were is the modile located on remote starts

2006 Ford Explorer Scheduled Maintenance Guide

0

Filed Under (Ford Manuals) by admin on 12-02-2012

download
Scheduled Maintenance: 2006 Ford Explorer Driving Condition: Normal Condition Engine Displacement Transmission Fuel Cylinders Drivetrain 4.0 L Automatic Flexible 6 RWD ded Maintenance Mileage: Every 5,000 15 30 45 60 75 90 100 105 120 135 150 Value Package Price: See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer Change engine oil and replace oil filter (Up to 5 quarts of oil. Perform at specified mileage interval or every 6 months, whichever occurs first) – See dealer Perform multi-point inspection – See dealer Rotate and inspect tires; check wheel end play and turning noise – See dealer Inspect automatic transmission fluid level (if equipped with underhood dipstick) – See dealer Inspect brake pads/shoes/rotors/drums, brake lines and hoses, and parking brake system – See dealer Inspect engine cooling system and hoses – See dealer Inspect and lubricate all non-sealed steering linkage,ball joints,suspension joints,half and drive-shafts and u-joints – See dealer Inspect complete exhaust system and heat shields – See dealer Replace engine air filter – See dealer Replace fuel filter – See dealer Inspect 4×2 front wheel bearings; replace grease and grease seals, and adjust bearings – See dealer Change Premium Gold engine coolant – See dealer Inspect accessory drive belt(s) – See dealer Replace PCV valve – See dealer Replace spark plugs – See dealer Replace accessory drive belts (if not replaced within last 100,000 miles) – See dealer Replace rear axle lubricant – See dealer Change automatic transmission/transaxle fluid and filter – See dealer Notes: Prices are shown for illustrative purposes only and may vary based on required fluid quantities and other conditions. Information in this document is current as of January 07, 2010 and could change in the future.

Related Content:

replace radiator on hummer h3, 2006 nissan frontier cat replacement, hydraulic parking brakes on drive shaft, how to replace cat 05 frontier, how to replace an alternator on a 2006 honda pilot, how to replace a alternator on a 2006 honda pilot, how to change starter in 2006 chevy cobalt 2 2, ford explorer 2006 linkage repair, 2006 saturn ion maintenance recommendations, 2006 mercury 5 1 inboard starter smoking

Chevy 6 Lug Shock Extension Brackets Installation Instructions

0

Filed Under (Chevy Manuals) by admin on 26-12-2011

download
chevy 6 Lug Shock Extension Brackets – Installation Instructions For some vehicles it is easier to install the brackets with the shock in the vehicle. 1) Remove the lower shock bolt from the lower control arm. 2) Turn the shock 180 degrees. 3) Using the bolt provided, place the shock extender into the shock mount. 4) Using the factory bolt, install the shock extender onto the lower control arm. 5) Tighten the upper shock mount.

Related Content:

chevy cruze overheating problems, 07 chev hhr p0741, e 60 p0597, front end shock extender install, how much how to install shock extenders, po1516 silverado, po753 chevy uplander

2002 Chevrolet Chevy Suburban – 4WD Intake Manifold Replacement Manual

0

Filed Under (Chevrolet Manuals) by admin on 13-05-2011

download
Removal Procedure Important: The intake manifold, throttle body, fuel rail, and injectors may be removed as an assembly. If not servicing the individual components, remove the manifold as a complete assembly. 1. Remove the throttle body. Refer to Throttle Body Assembly Replacement in Engine Controls – 4.8L, 5.3L, and 6.0L. 2. Remove the fuel injectors. Refer to Fuel Injector Replacement in Engine Controls – 4.8L, 5.3L, and 6.0L. 3. Disconnect the following electrical connectors: 4. Remove the knock sensor harness electrical connector from the intake manifold. 5. Set the electrical harness aside. <- Back Forward -> Document ID# 738735 2002 Chevrolet Chevy Suburban – 4WD Print – Manifold absolute pressure (MAP) sensor (1) – Knock sensor (2) – Exhaust gas recirculation (EGR) valve, if equipped. 6. If equipped, remove the following EGR pipe bolts: 7. If equipped, remove the EGR pipe with valve. 8. If equipped, remove the EGR pipe gasket from the exhaust manifold If equipped with vacuum assisted brakes, remove the vacuum brake booster hose from the rear of the intake manifold.

Related Content:

control shift cable clip retainer for a 2002 chevy silverado 5 34 l 60 e, 2002 chevy malibu 3 1 intake air temp wiring diagram, 2003 chevy suburban p0741 check transmission range switch for proper operation, chevy silverado 5 3L throttle body diagram, replacing a purge valve on 2002 chevy cavalier

Related Content:

2006 chevrolet cobalt starter removal instructions, 05 kia sedona starter bolts, 2002 chevy impala starter repla, 2002 chevy impala starter replacement, how do you change a starter on a 2002 chevy impala, how to replace a starter on a 2001 mitsubishi diamante, kia sorento starter motor diagram, replacing starter on 2002 impala