how to change front disc brakes on a 2011 rav 4

You search PDF repair manual about how to change front disc brakes on a 2011 rav 4, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to change front disc brakes on a 2011 rav 4 Direct Download speed 5432 Kb/s

  how to change front disc brakes on a 2011 rav 4 Full Version speed 8172 Kb/s



2004 Toyota Camry Disc Brake System Service/ Repair Manual

0

Filed Under (Toyota Manuals) by admin on 13-04-2012

download
OVERHAUL HINT: Overhaul the RH side by the same procedures with LH side. REMOVE FRONT WHEEL 1. DRAIN BRAKE FLUID NOTICE: Wash off the brake fluid immediately if it comes into contact with a painted surface. 2. DISCONNECT FRONT FLEXIBLE HOSE 3. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder. a. REMOVE DISC BRAKE CYLINDER ASSY FR LH 4. Remove the 2 bolts and disc brake cylinder. a. REMOVE DISC BRAKE PAD KIT FRONT (PAD ONLY) 5. Remove the 2 brake pads with anti-squeal shim. a. 6. Remove the 2 anti-squeal shims from each of 2 brake pads . a. Using a screwdriver, remove the wear indicator from each of 2 brake pads . b. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 7. Remove the upper side front disc brake pad support plate. a. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 8. Remove the bottom side front disc brake pad support plate. a. 10. Remove the cylinder slide bush from the cylinder slide pin. a. REMOVE FRONT DISC BRAKE BUSH DUST BOOT 11. Remove the 2 bush dust boots from the disc brake cylinder mounting. a. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH 12. Remove the 2 bolts and disc brake cylinder mounting LH. a. 13. Using a screwdriver, remove the set ring and cylinder boot. a. REMOVE FRONT DISC BRAKE PISTON 14. Place a piece of cloth or similar, between the piston and the disc brake cylinder. a. Use compressed air to remove the piston from the disc brake cylinder. CAUTION: Do not place your fingers in front of the piston when using compressed air. NOTICE: Do not spatter the brake fluid . b. 2004 Toyota Camry L4-2.4L (2AZ-FE) REMOVE PISTON SEAL 15. Using a screwdriver, remove the piston seal from the disc brake cylinder. NOTICE: Do not damage the inner cylinder and the cylinder groove. a. REMOVE FRONT DISC BRAKE BLEEDER PLUG CAP 16. REMOVE FRONT DISC BRAKE BLEEDER PLUG 17. INSPECT BRAKE CYLINDER AND PISTON Check the cylinder bore and piston for rust and scoring 18.

Related Content:

Remove front rotor 2003 Highlander, 2006 ford 500 sel misfire engine, how to repair cylinder no 4 on 2007 dodge charger, cylinder set up on 2003 Escape, misfire on number 2 cylinder on kia sedona, how to eplace brake backing plate on 1997 F350 floating axle, how to repalce ignition switch on 2005 cts, how to replace cylinder head rav4 2004, misfire 2009 pontiac g6, 1940 dodge Master Cylinder Diagram

1995 Mazda MX-6 FRONT DISC BRAKE PADS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mazda Manuals) by admin on 16-02-2012

download
REMOVAL & INSTALLATION FRONT DISC BRAKE PADS Removal & Installation 1. Raise and support front of vehicle. Remove front wheel assemblies. Remove lower lock pin/guide bolt. See Fig. 2 . Pivot caliper upward and support using rope. 2. Remove pads, shims, guide plates or pad guides and “V” springs (if equipped). Replace pad if lining thickness is less than specified. See MINIMUM PAD LINING SPECIFICATIONS (FRONT) table. 3. To install, reverse removal procedure. Use Disc Brake Expander (49-0221-600C) and an old pad to push piston fully inward to install disc pads. Fig. 2: Exploded View Of Front Brake Disc Assembly Courtesy of MAZDA MOTORS CORP. MINIMUM PAD LINING SPECIFICATIONS (FRONT) Application Thickness In. (mm) MX-6, 626 FRONT DISC BRAKE CALIPER Removal & Installation Raise and support front of vehicle. Remove front wheel assemblies and disconnect brake hose. Plug all openings. Remove front disc brake pads. See FRONT DISC BRAKE PADS . Remove remaining mounting bolt(s). Remove caliper from vehicle. To install, reverse removal procedure. Bleed air from system. FRONT BRAKE ROTOR Removal & Installation 1. Raise and support front of vehicle. Remove front wheel assemblies. Remove front disc brake caliper with brake hose connected. See FRONT DISC BRAKE CALIPER . Wire caliper aside. Remove rotor-to-hub screws (if equipped). Remove rotor. 2. Machine rotor if lateral runout exceeds specification. Replace rotor if measured thickness is less than specified minimum thickness. See DISC BRAKE SPECIFICATIONS table. To install, reverse removal procedure. REAR DISC BRAKE PADS Removal & Installation 1. Raise and support rear of vehicle. Remove rear wheel assemblies. Release parking brake and disconnect parking brake cable from caliper. Remove manual adjustment gear concealment plug from caliper. See Fig. 3 . Insert an appropriate size Allen wrench through hole and turn manual adjustment gear counterclockwise to retract caliper piston. 2. Remove upper guide bolt from caliper. Rotate caliper downward and support using wire. Remove “M” springs. Remove pads, shims and guide plates. Replace pad if lining thickness is less than .04″ (1.0 mm). 3. To install, reverse removal procedure. Turn manual adjustment gear clockwise until brake pads slightly touch rotor. Turn manual adjustment gear back 1/3 turn.

Related Content:

2007 chevy tahoe min disc thickness after machining, 95 chevy monte carle front brake rotor minimum thickness, Minimum Rotor Thickness Spec Sheet, pontiac pursuit parking brake cable, minuem roter tickness, minimum rotor thickness for chrysler pacifica, min spec for 2008 mada brake rotor thickness, mimimum rotor thickness for a 2000 chrysler sebring, mazda 626 pin size brake pads, how do i replace the rear brake caliper guide pin on a 2005 kia spectra

2001 Toyota Echo L4-1.5L Transmission and Drivetrain Clutch Service and Repair Manual

0

Filed Under (Toyota Manuals) by admin on 04-06-2011

download
REMOVAL 1. REMOVE TRANSAXLE FROM ENGINE 2. REMOVE CLUTCH COVER AND DISC a. Align the matchmark on the clutch cover with the one on the flywheel . b. Loosen each set bolt one turn at a time until spring tension is released. c. Remove the set bolts, and pull off the clutch cover with the clutch disc . NOTICE: Do not drop the clutch disc . 3. REMOVE RELEASE BEARING AND FORK FROM TRANSAXLE Remove the release bearing with the fork together and then separate them. 4. REMOVE RELEASE FORK SUPPORT AND BOOT INSPECTION 1. INSPECT CLUTCH DISC FOR WEAR OR DAMAGE Using vernier calipers, measure the rivet head depth. Minimum rivet depth: 0.3 mm (0.012 inch) If necessary, replace the clutch disc . Zoom Sized for Print Zoom Sized for Print Inspect Clutch Disc Runout 2. INSPECT CLUTCH DISC RUNOUT Using a dial indicator, check the disc runout. Maximum runout: 0.8 mm (0.031 inch) If necessary, replace the clutch disc runout. 3. INSPECT FLYWHEEL RUNOUT Using a dial indicator, check the flywheel runout. Maximum runout: 0.1 mm (0.004 inch) If necessary, replace the flywheel . Torque: 1st: 49 Nm ( 00 kgf-cm, 36 ft. lbs.) 2nd: Turn 90° 4. INSPECT DIAPHRAGM SPRING FOR WEAR Using vernier calipers, measure the diaphragm spring for depth and width of wear. Maximum: A (Depth): 0.5 mm (0.020 inch) B (Width): 6.0 mm (0.236 inch) If necessary, replace the clutch cover.

Related Content:

runout pdf, toyota echo transmission repair manual

2001 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 18-02-2012

download
Wheel Hub Removal All vehicles 1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 . 2. NOTE: Caliper is removed for clarity. Position aside the front disc brake caliper and anchor plate (2B292). 1. Remove the two front disc brake caliper anchor plate bolts. 2. Remove the front disc brake caliper anchor plate and position aside. 3. NOTE: Carry out this step for F-250 and F-350 4×4 SRW vehicles. Remove the rotor. 4. NOTE: Carry out this step for DRW vehicles. NOTE: If excessive force must be used during brake rotor removal, the brake rotors should be checked for lateral runout prior to installation. For additional information, refer to Section 206-00 . Remove the eight hub extender nuts, the hub plate and the rotor. 1. Remove the eight hub plate nuts. 2. Remove the hub plate. 3. Remove the rotor. 5. Remove the hub lock. 1. Remove the retainer ring. 2. Pull outward and remove the hub lock. 6. Remove the axle shaft thrust washers. 1. Remove the snap ring. 2. Remove the three thrust washers. Vehicles equipped with ABS 7. sensor from the bearing. Disconnect the ABS wheel sensor harness. 1. Disconnect the connector. 2. Disconnect the harness routing clips. All vehicles 8. NOTE: The wheel hub and bearing is a slip fit design and should not require a puller to remove it. Remove the wheel hub and bearing. 1. Remove the four lock nuts. 2. Remove the wheel hub and bearing 9. If necessary, remove the brake disc shield. Vehicles with ABS 10. If necessary, remove the bolt and the ABS sensor. All vehicles 11. NOTE: If necessary, position the hub in a soft-jawed vise. Install two nuts on the studs and use the inner nut to remove the studs. 12. Remove and discard the O-ring. Installation All vehicles 1. NOTE: Any time the wheel hub is removed for any reason, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive operations. Install a new O-ring. 2. NOTE: Position the hub in a soft-jawed vise. Install two nuts on the studs and use the outer nut to install the studs. Vehicles equipped with ABS 3. Position the ABS sensor and install the bolt. All vehicles 4. Position the brake disc shield. 5. NOTE: Apply a coat of Ford High Temperature 4×4 Front Axle and Wheel Bearing Grease E8TZ-19590-A meeting Ford specification ESA-M1C198-A to the O-ring area of the wheel hub and bearing before installing the hub and bearing. Install the wheel hub and bearing. 1. Position the wheel hub and bearing. 2. Install the four lock nuts. Vehicle equipped with ABS 6. NOTE: The following step applies only to vehicles equipped with ABS. Connect the ABS sensor harness. 1. Position the ABS sensor harness and install the routing clips. 2. Connect the harness connector. All vehicles 7. n-metallic thrust washer must be installed between the two metal thrust washers. Failure to do so will cause severe wear to the non-metallic thrust washer, allowing the axle shaft to travel further in and out during torque thrust causing damage to the wheel hub and bearing, the axle shaft end seal and the axle shaft. Install the snap ring. 1. Position the three thrust washers onto the axle shaft. 2. Install the snap ring. 8. NOTE: Any time the hub lock is removed, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive functions. Install a new O-ring. 9. Install the hub lock. 1. Position the hub lock. 2. Install the retainer ring. 10. Position the front disc brake rotor (1125) to the wheel hub (1104). Make sure the wheel hub and the front disc brake rotor braking and mounting surfaces are clean. ? Use brake parts cleaner to clean the front disc brake rotor. 11. NOTE: Carry out this step for DRW vehicles only. Install the front wheel hub extender and nuts.

Related Content:

1995 ford 150 4 wheel drive front hub removal, how to replace wheel bearings on a 08 silverodo, Need to torque specifications 1999 GMC 1500 wheel hub bearings, 1977 ford f-350 rear wheel diagram, how to remove a rusted hub assembly, 1998 f250 4x4 front hub bearings torque specs, snap ring assemble, 2009 impala hub mounting bolt torque, Removing and repalcement2000 toyota tundra wheel bearing assembly, how to change rear hub assembly on a 2006-2010 saturn vue with disk brakes

Toyota Landcruiser Rear Brake Upgrade Package / Installation Manual

0

Filed Under (Toyota Manuals) by admin on 23-03-2012

download
Toyota Landcruiser Rear Brake Upgrade Package HOPPERS STOPPERS HOPPERS STOPPERS HOPPERS STOPPERS HOPPERS STOPPERS 4 4 4 4 Rear Brake Upgrade Package 78/79 Series Toyota Landcruiser Cause of Rear Brake Problems 1 Combining a drum handbrake and a disc rotor and caliper within the confines of a 16-inch wheel necessitates a small brake caliper and small pad radial section, resulting in an undersized pad area. The standard design has a thin disc and a handbrake of small diameter and swept area relative to the weight of the vehicle. 2 The backing plate and handbrake arrangement allow mud and slurry to enter but not exit, causing abrasives to accumulate and rapidly destroy the handbrake, including its function as an emergency brake. 3 The small disc pad contact area is at odds with the affects of loading under abrasive conditions where rates of wear are parabolic for wear rate versus load. 4 The handbrake design is fiddly and complicated with many small parts that prove to be difficult to assemble correctly. Hoppers Stoppers design solution There appear to be a few possible ways to approach this problem, with a couple of companies proposing designs. Some take unconventional and unusual approaches but appear expensive to purchase and repair; with their application probably only justified if they perform perfectly for a very long time. Hoppers Stoppers’ approach is to stick to proven principles and overcome the basic weakness of the existing design. By all reports, the front brakes on these Toyotas work adequately, and considering their environment do not give significant problems in the field. In our view these brakes are not particularly special in their engineering, just the same basic front brakes that they have made for many years. If we built a rear brake set as solid and even better designed than the front it should last as long. This requires a big, thick disc rotor and brake lining swept area similar to the front

2003 Volvo S40 L4-1.9L Rear Brake Pads Removal And Installation Manual

0

Filed Under (Volvo Manuals) by admin on 16-02-2012

download
the hub cap and the wheel * the retaining clip and the brake hose from the support * the upper bolt from the locating pin for the brake caliper . Twist the brake caliper backwards. Remove the brake pads. NOTE: Do not depress the brake pedal while the brake pads are removed. Checking and cleaning the rear brake calipers Clean brake pad contact surfaces in the brake caliper and on the caliper mounting. Check the dirt guard for the piston. Replace the dirt guard if it is worn. Recondition the brake caliper if the dirt guard is defective. NOTE: If the dirt guard is defective, dirt may have penetrated the cylinder. Therefore the brake caliper must be reconditioned. Checking the rear brake disc Check the brake disc surface. Check the lateral runout of the brake disc if the disc is uneven. Replace the brake disc if it is worn or grooved. NOTE: Minimum disc thickness = 8.4 mm . If installing new brake pads, the minimum disc thickness must be at least 8.9 mm . Checking the locating pins for the rear brake calipers Check the rubber sleeves on the locating pins. Replace if necessary. If necessary, lubricate the locating pins using Volvo silicon grease (P/N 1161325-4). Insert the locating pins in the rubber sleeves. The locating pins must slide into the sleeves easily. Rotating the brake piston backwards Block the brake caliper against the brake disc. Use special tool 999 5782. * Turn the plate (A) forward over the shaft and insert the tool * Install the lugs (B) in the cut-out in the brake piston * Turn the shaft (C) so that the plate (A) presses against the brake caliper * Turn the axle (D) to the right and press the piston back while turning the shaft (C) to the right so that the plate (A) is in contact with the brake caliper * Turn the brake piston back fully and remove the tool Install the wear indicator (A) on the under side of the inner installed brake pads. Install the brake pads. Position the brake caliper . Install the new locking bolt. Tighten to 33 Nm . Install the brake hose in the support. Install the retaining clip. NOTE: Secure adhesive foil onto the steel plates to prevent the rear brake pads from rattling. Installing the wheels Install wheels. Checking the brake fluid level WARNING: Always depress the brake pedal repeatedly before test driving the car. Check the brake fluid level

Related Content:

yukon air ride hose locking clip

2004 Chrysler Pacifica DISC BRAKE SHOES Removal And Installation Manual

0

Filed Under (Chrysler Manuals) by admin on 13-05-2011

download
DISC BRAKE SHOES Removal (Front) 1. Remove master cylinder fluid reservoir cap. 2. Raise and support vehicle. 3. Remove tire and wheel assembly. 4. Place appropriately sized C-clamp over brake caliper, placing screw-drive head against outboard shoe and hook against rear of caliper. Slowly tighten screw-drive retracting caliper pistons into bores and brake outboard brake shoe free from caliper fingers. See Fig. 22 . Remove C-clamp. 5. Once outboard shoe is free from caliper fingers, slide caliper inboard on guides providing clearance between the rotor and inboard brake shoe. 6. Slide an appropriate prying tool through center opening in top of caliper behind brake shoe between 2 caliper pistons. Use care not to come in contact with pistons or dust boots potentially damaging them. Pry against rear of inboard brake shoe braking it free from caliper pistons. 7. Remove the 2 brake caliper guide pin bolts. See Fig. 23 . 8. Remove disc brake caliper from brake adapter and hang out of way using wire or a bungee cord. Use care not to overextend brake hose when doing this. 9. Remove brake shoes from disc brake caliper adapter. See Fig. 27 . 10. Install master cylinder fluid reservoir cap. 2. Install disc brake caliper over brake shoes on brake caliper adapter. See CALIPER . 3. Align guide pin bolt holes with guide pins and install caliper guide pin bolts. See TORQUE SPECIFICATIONS . 4. Install tire and wheel assembly. See TORQUE SPECIFICATIONS . 5. Lower vehicle. 6. Pump brake pedal several times to seat shoes to caliper and brake rotor. 7. Check and fill brake fluid level as necessary. See CHECKING & FILLING under BRAKE FLUID in SERVICE. 8. Road test vehicle making several stops to wear off any foreign material on brakes and to seat brake shoes. Removal (Rear) 1. Raise and support vehicle. 2. Remove both rear tire assemblies from vehicle. 3. Remove 2 caliper guide pin bolts. 4. Remove the 2 caliper guide pin bolts. See Fig. 24 . 5. Remove caliper from caliper adapter. See CALIPER . 6. Remove outboard brake shoe by pushing shoe away from caliper fingers, dislocating locating pins built into shoe backing plate from holes in caliper fingers, then sliding brake shoe down and off of brake caliper. See Fig. 28 . 7. Pull inboard brake shoe away from caliper piston, dislocating retaining clip from cavity in piston. Remove inboard shoe. NOTE: In some cases, it may be necessary to retract caliper piston in its bore a small amount in order to provide sufficient clearance between shoes and rotor to easily remove caliper from knuckle. This can usually be accomplished before guide pin bolts are removed, but grasping rear of caliper and pulling outward working with guide pins, thus retracting piston. DO NOT push on piston directly as it may get damaged.

Related Content:

4L80E Troubleshooting Guide, bench bleeding brake mc 97 ford ranger pdf, www motorcraftservice com owners guide, 2006 honda accord brake caliper torque, v reader repair, lucerne brake caliper torque spec, Mazda 6 Shop Manual PDF, proper torque for chevy truck pitman arm replacement 2004 avalanche, rear brake caliper removal on 2010 ford f-150, replacing caliper pin 2007 sienna

INFINITI BRAKE NOISE/ JUDDER/ PEDAL FEEL DIAGNOSIS AND REPAIR MANUAL

0

Filed Under (Infiniti Manuals) by admin on 06-02-2012

download
APPLIED VEHICLES: All Infiniti SERVICE INFORMATION • This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. • Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. BRAKE NOISE • Brakes can make a range of noises when applied or released. Some noises are normal and no repair action should be taken. • Use the following descriptions to identify the specific type of brake noise and the appropriate repair: Squeak noise when the brakes are cold: • Usually occurs during the first few stops in the morning. • This is a normal condition. No service action is necessary Squeak noise with the brakes at normal operating temperatures: • listed under Brake Service on page 5 of this bulletin and the appropriate Service Manual procedures. • Refer to technical bulletins specific to the model of vehicle regarding this issue. If there are no bulletins for the car you are working on, install OE type pads using the information Notes about brake pads and brake noise: Original Equipment (OE) brake pads are installed on all current Infiniti vehicles at the factory. The OE pads use a Non-asbesto • s Organic (NAO) compound. The NAO material provides state of the art resistance to squeal noise. • ervice parts and must be used if replacing brake pads under the terms of • ted under Brake Service on page 5 of this bulletin and the appropriate Service Manual Gro n s after coming to a stop: • It is a normal condition. No repair or service is necessary. These pads are available as s the Infiniti new car warranty. Loud continuous squeak/squeal noise: • Occurs with or without braking. • This is a normal brake function. It occurs when the brake pad wear indicators contact the rotor. It indicates the brake pads are worn out and need to be replaced. Install new brake pads using the information lis procedures. anoise when slightly releasing the brake • This is sometimes called “creep groan

Related Content:

4t65e documentation pdf, 4t65e pdf

2003 Volvo XC90 2.5T L5-2.5L Turbo Brake Pad Service and Repair Manual

0

Filed Under (Volvo Manuals) by admin on 12-06-2012

download
Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove: 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 9.50 Page 1 Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove: 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 2 -the brake caliper from the holder -the brake pads. Hang the brake caliper in a steel wire from the rear spring so as not to damage the brake hose. NOTE: Do not depress the brake pedal while the brake pads are removed. Cleaning the brake caliper 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 1 Brake Pad: Service and Repair Rear Brake Pads Brake Pads Rear, Replacing NOTE: The illustrations in this service information are used for different model years and/or models. Some variation may occur. However, the essential information in the illustrations is always correct. Preparations Remove the wheels on both sides. Removing brake pads NOTE: Minimum recommended pad thickness/replacement limit when installing new brake pads = 3.0 mm . Remove the retaining springs and locating pins for the brake calipers. Remove: -the securing spring (3) carefully so that it does not deform -the protective caps (1) from the two locating pins (2) -the locating pins, use hex socket 7 mm . Remove:
2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 2 -the brake caliper from the holder -the brake pads. Hang the brake caliper in a steel wire from the rear spring so as not to damage the brake hose. NOTE: Do not depress the brake pedal while the brake pads are removed. Cleaning the brake caliper 2003 Volvo XC90 2.5T L5-2.5L Turbo VIN 59 B5254T2 Copyright © 2007, ALLDATA 9.50 Page 3 Clean and check the brake caliper and dust cover. Clean and check the brake pad mating surfaces in the brake caliper and caliper holder. Check piston dust boot. NOTE: If the dust boot is damaged dirt may have penetrated the cylinder. If this is the case the caliper must be replaced. Checking the brake disc Check brake disc friction surfaces. If the brake disc displays signs of out-of-true, check its lateral run out. Replace the brake disc if it displays signs of heavy wear, variable thickness or similar. NOTE: Minimum disc thickness/replacement limit = 18.0 mm . Minimum recommended disc thickness when installing new brake pads = 18.7 mm . Installation Installing the brake pads

Related Content:

volvo xc90 2 5t turbo, 2009 scion xb rear pad replacement, 20020 envoy how to replace brake dustshield, f53 brake replacement, D12VolvoManual Printable, 2005 4runner brake rotor removal, tools needed to change brakes on 2008 pontiac torrent, change brake pads 2008 scion, cavalier 2003 service manual, 2003 volvo v40 headlight screws manual

2003 Honda Accord LX REAR DISC BRAKE PADS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 31-05-2011

download
Removal Raise and support vehicle. Remove wheels. Thoroughly clean outside of caliper to prevent dust and dirt from entering inside. Support caliper with a piece of wire to prevent damage to brake hose. Remove 2 caliper bolts and caliper from bracket. Remove pad shims and pads. Using vernier calipers, measure the thickness of each brake pad lining. Measurement does not include pad backing plate thickness. See DISC BRAKE SPECIFICATIONS . Remove pad retainers. Inspection Clean caliper thoroughly; remove any rust, and check for grooves and cracks. Check brake disc for damage and cracks. Measure brake pad thickness. See DISC BRAKE SPECIFICATIONS . If brake pad thickness is less than service limit, replace pads as a set. Installation 1. Install pad retainers. Apply Molykote M77 compound onto pad side of shim. Wipe excess grease off shim. Keep grease off discs and pads. Install brake pads and shims. Install inner pad with its wear indicator facing downward. If you are reusing pads, install in original position. Rotate caliper piston clockwise into cylinder, then align cutout in piston with tab on inner pad by turning piston back. See Fig. 15 . 2. Lubricate boot with rubber grease to avoid twisting. If boot is twisted, back it out and position properly. Install brake caliper. Install and torque caliper bolts to proper specification. See TORQUE SPECIFICATIONS . Install brake hose onto suspension arm with mounting bolt. After installation, check for leaks. Pump brake pedal several times to seat pads. Bleed brakes as necessary. See BLEEDING BRAKE SYSTEM . WARNING: Frequent inhalation of brake pad dust, regardless of material composition, could be hazardous to your health. Avoid breathing dust particles. NEVER use an air hose or brush to clean brush assembly. Use an OSHA-approved vacuum cleaner. NOTE: Engagement of brake may require a greater pedal stroke immediately after brake pads have been replaced as a set. Several applications of brake pedal will restore normal pedal stroke.

Related Content:

brake torque specs for 2007 honda accord, honda accord rear brake pad retainer, torque specs 2008 accord rear brakes

Related Content:

Remove front rotor 2003 Highlander, 2006 ford 500 sel misfire engine, how to repair cylinder no 4 on 2007 dodge charger, cylinder set up on 2003 Escape, misfire on number 2 cylinder on kia sedona, how to eplace brake backing plate on 1997 F350 floating axle, how to repalce ignition switch on 2005 cts, how to replace cylinder head rav4 2004, misfire 2009 pontiac g6, 1940 dodge Master Cylinder Diagram