change oil pump pontiac 2001 3

You search PDF repair manual about change oil pump pontiac 2001 3, if there are search results will appear below. If search results do not exist, please search by others keyword.



  change oil pump pontiac 2001 3 Direct Download speed 5432 Kb/s

  change oil pump pontiac 2001 3 Full Version speed 8172 Kb/s



1997-2001 HONDA CR-V (4WD) Noise From the Rear Differential REPAIR PROCEDURE

0

Filed Under (Honda Manuals) by admin on 06-01-2012

download
REPAIR PROCEDURE 1. Drain and refill the rear differential with Dual Pump Fluid. 2. Check the tires for proper inflation (recommended cold inflation front and rear is 26 psi) and any variation in tire size or type. 3. Test-drive the vehicle in a parking lot. Make tight, low-speed turns. If the noise is eliminated, return the vehicle to the customer. If the noise is still present, go to step 4. 4. Remove the rear differential assembly (see page 15-16 of the 1997-01 CR-V Service Manual). 5. Remove the torque control differential case, then remove and discard the 30 mm shim and the clutch assembly (see steps 1 thru 10 on pages 15-20 thru 15-22 of the service manual). 6. Remove the thrust needle bearing, the oil pump driveshaft, and the oil pump body assembly (see steps 11 and 12 on page 15-22 of the service manual). 7. Install the new flow collar over the drive pinion shaft. Make sure the tabs of the flow collar align with the oil pump pin. 8. For 1997 models: Assemble the new oil pump (spring, O-rings, piston, and pump body assembly). 9. Align the rear oil pump grooves with the oil pump pin and the flow collar tabs, then install the oil pump body assembly on the differential carrier. 10. Tighten the oil pump body assembly bolts to 12 N·m (8.7 lb-ft). 11. Align the oil pump driveshaft tabs with the grooves of the front oil pump in the oil pump body assembly, then install the oil pump driveshaft. 12. Install the thrust needle bearing with the outer race facing up.

Related Content:

differential service procedures, 2006 suburban oil pump replcement procedure, picture of 1997 4x4 honda passport axle warning lights, 1997 dodge ram 4x4 1500 service manual download, oil pump leak 2003 accord, oil pump on a 307, oil punp removal 2002 trailblazer, rav4 rear oil leak, Toyota 4 Y oil pump, what causes 147 transaxle code on 97 e420 mercedes

2004 Honda Element EX ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) CIRCUIT HIGH VOLTAGE MANUAL

0

Filed Under (Honda Manuals) by admin on 20-06-2012

download
1. Check the engine oil level. Is the level OK? YES- Go to step 2 . NO- Adjust the engine oil to the proper level, then go to step 14 . 2. Turn the ignition switch ON (II). 3. Clear the DTC with the HDS. 4. Do the VTEC TEST in the INSPECTION MENU with the HDS. Is the result OK? YES- Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch) and the ECM/PCM. NO- Go to step 5 . 5. Check the result of step 4 . * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Failure * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Open * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) SIG Line Open * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) GND Line Open Is the test result any of the above? YES- Go to step 6 . NO- Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch). If it is OK, replace the rocker arm oil control solenoid (VTEC solenoid valve) (see step CMP SENSOR A REPLACEMENT ), then go to 14 . 6. Turn the ignition switch OFF. 7. Disconnect the rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector. 8. Check for continuity between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminals No. 1 and No. 2 Fig. 16: Checking Continuity Between Rocker Arm Oil Pressure Switch 2P Connector Terminals Courtesy of AMERICAN HONDA MOTOR CO., INC. Is there continuity? YES- Go to step 9 . NO- Replace the rocker arm oil pressure switch (VTEC oil pressure switch) (see ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) REMOVAL/INSTALLATION ), then go to step 13 . 9. Turn the ignition switch ON (II). 10. Measure voltage between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminal No. 1 and body ground

Related Content:

solenoid 2007 honda, saturn ion shift handle micro switch, causes of low oil pump presure on 4l60e, dt466 injection control pressure, 4r100 pressure ports, chevrolet silverado oil pressure sensor repair, replacing oil pressure switch on gmc sierra, crv honda 2004 vtech oil pressure switch, injection actuation pressure sensor no c7 cat, location of oil pressure switch 2005 Honda cr-v

1993 Ford Escort CIRCUIT TEST J – FUEL PUMP CIRCUIT (RELAY AND INERTIA SWITCH)

0

Filed Under (Ford Manuals) by admin on 19-01-2012

download
resistance between test pin No. 22 and test pins No. 40 and 60. If resistance is less than 10,000 ohms, repair short circuit and repeat QUICK TEST. If resistance is 10,000 ohms or more, go to step 5). 5)Check Fuel Pump Circuit Continuity Turn ignition off. Leave fuel pump relay and PCM disconnected. Measure resistance between FUEL PUMP circuit at fuel pump relay wiring harness connector and test pin No. 22 at breakout box. If resistance is less than 5 ohms, replace PCM and repeat QUICK TEST. If resistance is 5 ohms or more, repair open circuit and repeat QUICK TEST. 10)Code 95/542 A KOEO Code 95/542 indicates one of the following conditions: Engine Starts: * Fuel pump secondary circuit shorted to power. * Fuel pump relay contacts always closed. * Open FPM circuit between PCM and junction to POWER-TO-PUMP circuit. * Left/front HO2S short to power (dual HO2S applications). * Faulty PCM. No Start: * IFS switch circuit open or not reset. * Open circuit in or between PCM and fuel pump. * Faulty ground connection at fuel pump. * Faulty fuel pump. If engine starts, go to step 11). If engine does not start, go to step 15). 11)Check Fuel Pump Operation Turn ignition on. Wait 5 seconds. Listen for fuel pump operation. If fuel pump is off, go to step 13). If fuel pump is on, go to step 12). 12)Check For Fuel Pump Relay Always Closed Turn ignition off. Disconnect fuel pump relay. Turn ignition on. If fuel pump is off with relay disconnected, replace fuel pump relay and repeat QUICK TEST. If fuel pump is on with relay disconnected, repair short to power in POWER-TO-PUMP or FPM circuit. (For models with relay block, also check fuel pump prime plug circuit). Repeat QUICK TEST. 13)Check Continuity Of Fuel Pump Monitor (FPM) Circuit Turn ignition off. Disconnect PCM 60-pin connector. Inspect and repair any damaged terminals. Install EEC-IV Breakout Box (T83L-50-EEC-IV) , leaving PCM disconnected. Disconnect fuel pump relay. Measure resistance between test pin No. 8 (No. 19 on Escort, and Tracer) at breakout box and POWER-TO-PUMP circuit at fuel pump relay wiring harness connector. If resistance is less than 5 ohms, go to step 25) (dual HO2S) or replace PCM and repeat QUICK TEST (single HO2S). If resistance is 5 ohms or more, repair open circuit and repeat QUICK TEST

Related Content:

99 subaru forester fuel line repair kits, lucas cav injection pump diagram, toyota so5d engine fule pump control wireing diagram pdf, 2002 isx cummins manual pump installation, rager injection pump parts manual, CAV Fuel Injector Pump (Ford Part #D6NN9A543G) repair manual, 89 dodge dakota fuel pump diagram, isuzu dmax fuel pump, how to change water pump on a dewoo, cav injector pump governor spring

2000 Audi A6 OIL PAN (A4 And A6) Removal And Installation Manual

0

Filed Under (Audi Manuals) by admin on 01-07-2012

download
OIL PAN(A4 & A6) Removal (Lower Pan- A4 & A6) 1. Disconnect negative battery cable. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Unbolt left and right swaybar stabilizer bracket bolts (4) from mounting bracket. See Fig. 98 . Lower swaybar stabilizer not more than 10cm (3.94 INCHES) and secure with heavy wire. 4. If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) bracket from right side oil pan. 5. Remove lower oil pan. To install oil pan (lower), see INSTALLATION (LOWER OIL PAN- A4 & A6) . Installation (Lower Oil Pan- A4 & A6) 1. Ensure oil pan surfaces are clean and dry. Remove residual sealant from oil pan, if necessary, with hand drill and plastic brush instead of a flat scrapper. See Fig. 99 . Install gasket. 2. Install 2 bolts diagonal to each other (to hold up pan). Install the rest of the bolts and hand tighten. 3. Starting at center and moving outward, tighten lower oil pan to upper oil pan bolts to 10 N.m (89 INCH lbs.). Tighten oil pan drain plug 30 N.m (22 ft. lbs.). Wait 30 minutes before filling with engine oil. Tighten all bolts to specification. See TORQUE SPECIFICATIONS . 4. To complete installation, reverse removal procedure. Fill and bleed cooling system. See COOLING SYSTEM BLEEDING . Removal (Upper Oil Pan- A4 & A6) 1. Disconnect negative battery cable. Remove oil dipstick. Unbolt oil dipstick tube at front of cylinder head. Remove oil dipstick tube. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Move lock carrier into service position. See LOCK CARRIER . This will allow servicing of front engine components and facilitate removal of oil pan. 4. Open coolant expansion tank cap, drain cooling system at radiator. Open the coolant pump bearing housing drain plug. Located at bottom of block near transmission bell housing, drivers side of vehicle. See Fig. 32 – Fig. 33 . If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) CAUTION: Wear eye protection NOTE: Obtain radio code before disconnecting battery. For help in identifying components and component locations, refer to illustrations Fig. 108 -Fig. 109 . NOTE: If engine is out of car, ensure oil pan is aligned with cylinder block on flywheel side. 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve bracket from right side oil pan. 5. Position Engine Support (10-222A) with (10-222A/3) engine support adapter, or equivalent, on bolted flanges of fenders. Connect support bracket to front and rear engine lifting eyes. Lift up engine as far as possible. DO NOT use excessive force to raise engine. 6. Cut tie wraps and open bracket supporting starter wiring. See Fig. 97 . Disconnect electrical connection at starter.

Related Content:

04 2 7l allroad p0491 p0492, cummins isx subassembly procedure, Oil Pan Gasket Leaking 2005 altima, replacing oil pan 2000 avalon, how to change oil pan gasket 2003 chevy silverado 5 3, instutins how to replce oil PAN GASKEET ON 2006 CHEV IMPLA 5 3, torque specs for 2004 chevy deisel oil pan, ntc cummins pan bolts, oil drain pan torque 1991 corrola, oil drain plug for 3406e cat

1998 Chevrolet Blazer Engine Oil Cooler Hose/ Pipe Removal And Installation Manual

0

Filed Under (Chevrolet Manuals) by admin on 22-05-2012

download
Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6. Rotate the retaining ring around the quick connector until the retaining ring is out of position and can be completely removed. Discard the retaining rings. 7. Remove the engine oil cooler lines from the quick connectors at the radiator engine oil cooler inlet and outlet. Pull the lines straight out from the connectors. 8. Remove the remote engine oil filter lines support clamp bolt. Important: Have a drain pan ready for the engine oil to drain into. 9. Remove the bolt attaching the remote engine oil filter lines to the remote (frame mounted) engine oil filter adapter. 10. Hold the remote engine oil filter lines below the remote engine oil filter lines (engine mounted) adapter to drain the engine oil. 11. Remove and discard the seals. 12. Remove the bolt attaching the remote engine oil filter lines to the remote engine oil filter lines (engine mounted) adapter. 13. Remove and discard the seals. 14. Clean all of the components in a suitable solvent, and dry them with compressed air. 15. Inspect the fittings, the connectors, the cooler lines, the cooler, the filter lines, and the remote filter adapter for damage, distortion, or restriction. Replace parts as necessary. 16. Flush the engine oil cooler, the engine oil cooler lines, the remote engine oil filter adapter, and the remote engine oil filter lines with the same type of engine oil normally circulating through the engine. Installation Procedure

Related Content:

replace oil cooker 3406 cat motor, 2001 a4 oil cooler lines, 2012 kia srento a/c condensor drain line drawing, 2006 impala oil filter housing gasket, oil cooler on 3406 cat how to change, 2006 chevy trailblazer engine removal, removing the oil pan on a 2008 impala 3 5, 2005 ford escape 2 3liter oil dipstick housing seal, clips for blazer oil cooling lines, oil flow path for 5 3 chevrolet

1998 Acura 3.5RL FUEL PUMP RELAY (3.5RL) INSTALLATION MANUAL

0

Filed Under (Acura Manuals) by admin on 13-06-2011

download
Fuel pump relay is located in the front of the trunk. Turn ignition switch to START position. If engine starts, go to next step. If engine does not start, go to FUEL PUMP RESISTOR (3.5RL) . 2. Turn engine off and ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is present, go to next step. If battery voltage is not present, go to step 4). 3. Start engine and run at 3000 RPM with no loads and transmission in Park or Neutral, until radiator fan comes on. Allow engine to idle for at least one minute. Turn engine off. Disconnect vacuum hose No. 21 from vacuum manifold. Apply 8-12 in. Hg (27-40 kPa) vacuum to Manifold Absolute Pressure (MAP) sensor. Start engine and run at 6500 RPM with no loads and transmission in Park or Neutral. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If less than one volt is present, fuel pump relay circuit is okay. If one volt or more is present, substitute a known good PCM, then recheck. If symptom or indication goes away, replace original PCM. 4. Turn ignition off. Disconnect PCM 26-pin and 12-pin connectors. Disconnect fuel pump relay 4-pin connector. Using a fused jumper wire, connect fuel pump relay connector terminals No. 2 (Red/White wire) and No. 4 (Green wire). Turn ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is not present, go to next step. If battery voltage is present, replace fuel pump relay. 5. Remove jumper wire. Measure voltage between ground and fuel pump relay 4-pin connector terminal No. 2 (Red/White wire). If battery voltage is present, repair open or short in Green wire between PCM and fuel pump relay. If battery voltage is not present, repair open in Red/White wire between fuel pump relay and FUEL PUMP fuse No. 22 (20-amp), located in underdash fuse/relay box. FUEL PUMP RESISTOR (3.5RL) 1. Fuel pump resistor is located in the left corner of the trunk. Disconnect fuel pump resistor 2-pin connector. Turn ignition on and measure voltage between ground and fuel pump resistor connector terminal No. 2 (Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, go to next step. If battery voltage is not present as specified, check PGM-FI relay. See PGM- FI MAIN RELAY . 2. Turn ignition off. Using a jumper wire, connect fuel pump resistor connector terminals No. 1 (Black/Yellow wire) and No. 2 (Yellow wire). Turn ignition switch to START position. If engine does not start, go to next step. If engine starts, replace fuel pump resistor. 3. Turn ignition off. Disconnect fuel unit sub-harness Gray, 10-pin connector located in front of trunk, above fuel pump access panel, next to Gray, 20-pin connector. Turn ignition on and measure voltage between ground and sub-harness connector terminal No. 7 (Black/Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, check fuel pump. If battery voltage is present as specified, repair open in Black/Yellow wire between fuel pump resistor and fuel pump

Related Content:

1998 jimmy fuel pump install, wire diagram on a 2002 grand prix headlight, 03 ford windstar fuel pump wiring, proper connection for horn relay 1968 chevelle, pcm drag adjustment, damaged fuel pump wiring, vcm ground wire, location of vent valve solenoid on 2010 ford ranger, 2005 tundra speed pulse signal wire location, 1998 s10 6 cylindes fuel regulator diagram

2008 Ford F-Super Duty LACKS POWER, LEAKS FLUID FROM EXHAUST PIPE, ABNORMAL TAILPIPE SEDIMENT, WHITE SMOKE, EXHAUST SMELL, AND MIL ON SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 02-02-2012

download
ACTION To diagnose and correct the concern, refer to the following Service Procedure. SERVICE PROCEDURE NOTE DO NOT START ENGINE Evaluation, Inspections, And Checks 1. Retrieve KOEO diagnostic trouble codes (DTCs). 2. Check oil level. Remove and clean dipstick. Reinsert into dipstick tube only until dipstick handle reaches top of dipstick tube (Figure 1). NOTE FIGURE 1 DEMONSTRATES DIPSTICK Figure 1 – Article 07-8-9 POSITIONING FOR OVER-FULL CHECK. KEEP 3. Check coolant level. DIPSTICK HANDLE OFFSET OF CENTER TO PREVENT IT FROM FULLY SEATING. IF OIL 4. Check fuel quality. LEVEL IS BELOW THE MAX MARK, OIL IS NOT OVER-FULL. 5. Inspect tailpipes for abnormal sediment; for example black soot, white ash, oil, coolant, or fuel. 6. Inspect vehicle for coolant, oil and fuel leaks at the following locations: •Tailpipes Repair Directions •Section A – If the following DTCs are present P0087, P2291, P0263-0284, P0300-P0308, or P1336 or if observation of external fuel leaks, for example, wetness around exhaust manifolds or over-full oil level indication. •Section B – If the following DTCs are present P132B, P2262, or P2263 or observation of oil leaks (aside from over-full oil level) or oil level is low. Figure 2 – Article 07-8-9 •Section C – If coolant low or observation of 8. Replace any leaking components and verify coolant leaks. leak has been repaired while running IDS high •Sections A, B, and C – If only abnormal sediment pressure fuel system test – KOER. in tailpipes. 9. Perform WSM, Section 303-04D – Turbocharger SECTION – A Bearing Clearance Check. Fuel System Diagnostics 10. If fuel quality is poor, drain all fuel and replace with known good ultra-low sulfur diesel fuel. NOTE IN CASES WHERE ENGINE OIL HAS BEEN 11. If no DTCs were stored in pending or DILUTED WITH DIESEL FUEL AND ALL REPAIRS continuous memory go to Step 13. ARE COMPLETE, RELEASE THE OIL FILTER CAP 12. Is there abnormal sediment in tailpipes or fuel ALLOWING OIL TO DRAIN TO OIL PAN AND evident? KEEP FILTER, DRAIN THE OIL FROM OIL PAN AND FILL WITH NEW OIL. TIGHTEN OIL FILTER a. No – Complete PC/ED worksheet and CAP AND RUN ENGINE FOR 10 MINUTES. applicable PPT tests for the codes retrieved. FINALLY, CHANGE OIL FILTER AND OIL AGAIN. b. Yes – Go to Step 13. 1. If oil is not over-full – go to Step 9. 13. Is there abnormal sediment in the tailpipes?

Related Content:

ford 2014 c max service manual

1998 Dodge Grand Caravan Fuel Pump Relay Removal And Installation Manual

0

Filed Under (Dodge Manuals) by admin on 13-06-2012

download
Fuel Pump Relay 1. Remove fuel pump relay from power distribution center at driver’s side front corner of engine compartment, near the battery. Note terminal identification on fuel pump relay. See Fig. 6 . 2. To check fuel pump relay resistance, use ohmmeter and check resistance between terminals No. 85 and 86 on fuel pump relay. Replace fuel pump relay if resistance is not 70-80 ohms. 3. To check fuel pump relay operation, connect ohmmeter between terminals No. 30 and 87A on fuel pump relay. See Fig. 6 . Ohmmeter should indicate continuity between terminals No. 30 and 87A on fuel pump relay. 4. Connect ohmmeter between terminals No. 30 and 87 on fuel pump relay. See Fig. 6 . Ohmmeter should indicate no continuity between terminals No. 30 and 87 on fuel pump relay. 5. Connect 16-gauge jumper wire between negative battery terminal and terminal No. 85 on fuel pump relay. Connect 16-gauge jumper wire between positive battery terminal and terminal No. 86 on fuel pump relay. 6. Fuel pump relay should now be energized. No continuity should now exist between terminals No. 30 and 87A on fuel pump relay. Continuity should now exist between terminals No. 30 and 87 on fuel pump relay. Disconnect jumper wires. Replace fuel pump relay if defective. 7. If fuel pump relay or wiring circuit failure exists, a Diagnostic Trouble Code (DTC) will be stored in Powertrain Control Module (PCM). See appropriate G – TESTS W/CODES article. Fig. 6: Identifying ASD Relay & Fuel Pump Relay Terminals Courtesy of CHRYSLER CORP.

Related Content:

yhs-default, fuse for right headlight eclipse 2000, location of fan relay 98 trans am, which is the fuel pump relay on 2011 durango, 99 eldorado fuel pump relay test, where is the relay switch for liftgate in 2005 esclade, where is the washer relay located in a 2009 chevy impala, 1993 corvette power seat and power window shorting out breaker, sensor switch on rear beam axle of 2005 saturn relay, g5 sunroof relay

1997 Saturn SL2 OIL PUMP REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Saturn Manuals) by admin on 03-06-2012

download
Removal & Disassembly Remove engine front cover. See FRONT COVER & TIMING CHAIN under REMOVAL & INSTALLATION. Using an impact driver and a T-30 Torx bit, remove and discard oil pump cover plate screws. Remove cover plate and rotors. See Fig. 11 . To remove oil pump relief valve, use a slide hammer and Relief Valve Puller Adapter (SA9103E). Inspection Replace rotors if worn or damaged. Using feeler gauge and straightedge (at cover plate), measure oil pump clearances. See OIL PUMP SPECIFICATIONS table. If clearances are not as specified, replace rotors or entire pump assembly as necessary. Reassembly & Installation Install rotors with chamfer facing away from engine. Install new relief valve (if removed). Pack pump rotors with petroleum jelly to prime pump. Install pump cover plate using new screws. Tighten screws to specification. See TORQUE SPECIFICATIONS . OIL PUMP SPECIFICATIONS NOTE: If oil pump relief valve is removed, DO NOT reuse it. Application In. (mm) Outer Rotor-To-Housing .006-.011 (.150-.277) Outer Rotor Tip-To-Inner Rotor Tip .006 (.150) Rotor Gear-To-Pump Cover Plate

Related Content:

01 saturn dtc p1635

OIL PAN ADAPTER INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 24-02-2012

download
Remove the oil pan prior to installing the oil pan adapter. Refer to a factory service manual for your vehicle for reference. 2. The Oil Drain Adapter requires the oil pan to be drilled. The hole should be located above the oil level in the pan in an area that does not interfere with any other parts and that will allow oil to flow freely from the drain hose. Mark the area to be drilled. We find that typically, locating the center drain hole 1.5″from the Oil Pan Rail, provides clearance between the adapter fitting and the pan rail, and also keeps the drain hole above the oil level in the pan (See Fig. 1) . Using a scratch awl, mark the center of each bolt hole 9/16″away from the center of the center drain hole so the distance from center to center is 1.125″ (See Fig. 1) . 3. Using a center punch, indent each drilling location to prevent the drill bit from walking. Pre-drill each hole with a 1/8″bit. Secure the oil pan on a work bench or on a drill press, and drill the outer bolt holes to ¼”. Drill the center drain hole to ½”. Deburr the holes and thoroughly clean the oil pan to remove any metal shavings. 4. Install the Oil Drain Adapter onto the oil pan using the two of the ¼-20 bolts, ( Note: Select the appropriate length bolt for your application. If you have a cast aluminum oil pan, you will typically use the 5/8″long bolts; if you have a stamped steel oil pan, you will typically use the 1/2″long bolts. We recommend using blue Loctite on the threads.) and the two ¼” Stato-Seal washers on the inside of the oil pan, using the gasket on the outside of the pan (See Fig. 2a & 2b). Torque the bolts to 6-8 ft/lbs. 5. Re-install the oil pan. Refer to a factory service manual for your vehicle for reference.

Related Content:

Dodge 46rh convertor drain

Related Content:

differential service procedures, 2006 suburban oil pump replcement procedure, picture of 1997 4x4 honda passport axle warning lights, 1997 dodge ram 4x4 1500 service manual download, oil pump leak 2003 accord, oil pump on a 307, oil punp removal 2002 trailblazer, rav4 rear oil leak, Toyota 4 Y oil pump, what causes 147 transaxle code on 97 e420 mercedes