Skip to content

how to change shift cable on 2004 tahoe

You search PDF repair manual about how to change shift cable on 2004 tahoe, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Ford Truck Ranger 2WD Transmission Position Switch/ Sensor Service and Repair MANUAL

download
Special Tool(s) Removal 1. With the vehicle in NEUTRAL, position it on a hoist. 2. Disconnect the shift cable from the manual control lever. 3. Disconnect the digital transmission range (TR) sensor electrical connector. 4. Remove the manual control outer lever nut and manual control outer lever. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E 5. Remove the screws and the digital TR sensor. Installation 1. Install the digital TR sensor and loosely install the screws. 2. CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged. NOTE: The manual lever must be in the NEUTRAL position. Using the special tool, align the digital TR sensor and tighten screws in an alternating sequence. 3. Install the manual control outer lever and nut. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E Copyright © 2007, ALLDATA 9.50 Page 3 4. Connect the digital transmission range (TR) sensor electrical connector. 5. Connect the shift cable to the manual control lever. 6. Verify that the shift cable is adjusted correctly.

GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps)

download
GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps) Models: 2004-2007 Buick Rainier 2008 Buick Enclave 2003-2008 Cadillac Escalade Models 2005-2008 Cadillac CTS, SRX, STS 2006-2008 Cadillac DTS 2003-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer Models 2006-2008 Chevrolet Colorado 2007-2008 Chevrolet Equinox, HHR 2003-2008 GMC Envoy Models, Sierra, Yukon Models 2006-2008 GMC Canyon 2007-2008 GMC Acadia 2007-2008 Pontiac Torrent 2005-2008 HUMMER H2 2006-2008 HUMMER H3 2007-2008 Saturn OUTLOOK 2005-2008 Saab 9-7X This bulletin is being revised to update the models affected list. Please discard Corporate Bulletin Number 07-08-44-016 (Section 08 — Body & Accessories). Condition Some customers may comment on an inoperative display monitor or monitors in the GM Accessories Headrest DVD System. Cause This condition may be caused by a loose connection at the display monitor cable connectors. These connectors are located at the lower rear part of both front seats. Two cables are routed to the display monitor in each seat. Correction Do This Don’t Do This Install display monitor cable connector clamps. Do Not replace the DVD system display monitor. Important: A number of headrest monitors have been replaced under warranty and in many cases, no trouble was found by the supplier when these units were analyzed. Therefore, technicians should be checking for loose connections and installing cable connector clamps to ensure a positive and robust connection. Technicians are to install a video cable connector clamp on each cable connector located under each front seat. A total of four cable connector clamps, P/N 19159659, are required for each vehicle. The illustration above shows a pair of display monitor cable connectors without the cable clamps installed.

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

2004-2007 Ford F-Super Duty SLIDING POWER WINDOW (BACK GLASS) SERVICE MANUAL

download
FORD: 2004-2007 F-Super Duty ISSUE SERVICE PROCEDURE Some 2004-2007 F-Super Duty vehicles, equipped with a power sliding rear window (back glass), may 1. Prior to window removal, verify that center exhibit a stuck or binding concern. This condition glass is centered in the upper plastic channel may be due to the center glass not being positioned (Figure 1). If center glass is not inside upper correctly inside the upper or lower channel, the plastic channel, pull channel down and out of channel being warped, bent, or center glass upper aluminum channel and slide back in de-bonded. making sure the entire center glass is inside the plastic channel. ACTION Follow the Service Procedure steps to correct the condition. Figure 1 – Article 06-15-5 2. If Step 1 resolves the issue, return the vehicle 4. Refer to window removal procedure. (Refer to back to customer after verifying the window Workshop Manual (WSM), Section 501-11-24 functions properly. If it did not resolve the and 501-11-25.) issue, proceed to Step 3. 5. Remove cable clips from sheet metal. (Refer to 3. Open the rear window approximately half way. WSM, Section 501-11-28.) 6. Remove three (3) motor bracket attaching bolts. (Refer to WSM, Section 501-11-28. 7. Disconnect motor wiring harness from vehicle 9. Pull outer rubber seal from window frame body harness. (Refer to WSM, Section (Figure 2). 501-11-29.) 8. Remove window assembly from vehicle window opening. Figure 2 – Article 06-15-5 10. Locate two (2) screws in bottom of lower frame and remove them with a R1 square bit screw driver (Figure 3). Figure 3 – Article 06-15-5

1995-2004 Toyota Tacoma Helix Power Tower PLUS Installation Manual

download
1. Remove the air cleaner duct from throttle body. 2. Unbolt the throttle linkage from the intake plenum by unbolting the single 12mm-sized bolt. 3. Unbolt the lower vacuum line from intake plenum. Remove the four bolts (some models may have bolt/stud combination, either case they all need to be removed) from the intake manifold. 4. Separate throttle body from the intake plenum and remove the OE gasket. Place the Helix Power Tower PLUS (engraved side towards throttle body) with the new gaskets in between the throttle body and the intake plenum. Secure with the new longer bolts supplied with this kit. On 2003-2004 models you will need to use the longer 8mmx110mm bolts to complete the installation. Torque the assembly to 15 ft/lbs. 5. Install the throttle linkage extender plate to plenum (original stock location) with OE bolt. Please make sure the roll pin of the plate is in locator hole on plenum. Reinstall the throttle linkage to the extender plate and use the supplied hardware to secure it to the new extender plate. Torque both bolts to 10 ft/lb. 6. Install new vacuum line extender (black z-bend bracket) to original location with OE bolt and install vacuum line bracket to this extender with the supplied hardware. Torque both bolts to 8 ft/lb. (Note: it may be necessary to lengthen the linkage cable and vacuum line from the intake plenum anchor points) 7. Reinstall the air cleaner duct to the throttle body.