how to change speakers 2006 buick lucerne

You search PDF repair manual about how to change speakers 2006 buick lucerne, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to change speakers 2006 buick lucerne Direct Download speed 5432 Kb/s

  how to change speakers 2006 buick lucerne Full Version speed 8172 Kb/s



Remote Keyless Entry (RKE) Inoperative, Poor Range, Tire Pressure Monitor (TPM) Message Displayed, Remote Vehicle Start (RVS) (Replace/Reprogram RCDLR, Replace Antenna and Transmitters)

0

Filed Under (More Manuals) by admin on 28-01-2011

download
Models: 2006-2007 Buick Lucerne 2006-2007 Cadillac DTS 2006-2007 Chevrolet Impala, Monte Carlo 1. Replace the RCDLR module and the RCDLR antenna using the following procedure: Impala / Monte Carlo DTS • DTS / Lucerne: 5/1/07 • Impala / Monte Carle: 3/1/07 • The 2006 and 2007 Impala LS without AP8 does not have a coax antenna. • The 2006 and 2007 Lucerne without AP3 or AP8 does not have a coax antenna. 1.1. Remove the driver’s side “A” pillar molding and I/P closeout panel. 1.2. Unplug the speaker. 1.3. To expose the RCDLR antenna, partially remove the driver’s side upper I/P closeout panel (near windshield). 1.4. Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the “A” pillar. 1.5. Cut the old RCDLR antenna wire a minimum of 152 mm (6 in) from the button (connecting to the windshield), leaving that portion of the old RCDLR antenna connected to the windshield. 1.6. Remove the I/P carrier bolt and remove the old RCDLR antenna. 1.7. Remove the RCDLR module. 1.8. Install the new RCDLR module. 1.9. Lay in the new RCDLR antenna and reinstall the carrier bolt. 1.10. Connect the new antenna to the RCDLR antenna module. 1.11. Clip the new RCDLR antenna into place using the existing holes on the “A” pillar. 1.12. Reinstall the I/P close-out panel. 1.13. Reconnect the speaker wire. Important: Be sure that the end of the old RCDLR antenna is tucked behind the “A” pillar molding. The button on the windshield is no longer functional, however leaving the cover on the button will provide a cleaner look to the vehicle. 1.14. Reinstall the “A” pillar molding and I/P side closeout panel. 1.1. Remove the rear seat cushion. 1.2. Remove the rear seat back.

Related Content:

antenna repair torrent, 04 impaia p0455, 2006 chev impala remote lock location, how to remove 2007 dps rear seat, how to remove back seat in 2007 Buick lucerne, how to remove the back seat on buick lucerne 2006 v6, how to repace autana on 2000 tacoma, is the keyless entry module wiring in all 02 monte carlos, partially blown channel plate gasket 2001 chevy malibu, remove back seat 2008 dts

2006 Ford Explorer Scheduled Maintenance Guide

0

Filed Under (Ford Manuals) by admin on 12-02-2012

download
Scheduled Maintenance: 2006 Ford Explorer Driving Condition: Normal Condition Engine Displacement Transmission Fuel Cylinders Drivetrain 4.0 L Automatic Flexible 6 RWD ded Maintenance Mileage: Every 5,000 15 30 45 60 75 90 100 105 120 135 150 Value Package Price: See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer Change engine oil and replace oil filter (Up to 5 quarts of oil. Perform at specified mileage interval or every 6 months, whichever occurs first) – See dealer Perform multi-point inspection – See dealer Rotate and inspect tires; check wheel end play and turning noise – See dealer Inspect automatic transmission fluid level (if equipped with underhood dipstick) – See dealer Inspect brake pads/shoes/rotors/drums, brake lines and hoses, and parking brake system – See dealer Inspect engine cooling system and hoses – See dealer Inspect and lubricate all non-sealed steering linkage,ball joints,suspension joints,half and drive-shafts and u-joints – See dealer Inspect complete exhaust system and heat shields – See dealer Replace engine air filter – See dealer Replace fuel filter – See dealer Inspect 4×2 front wheel bearings; replace grease and grease seals, and adjust bearings – See dealer Change Premium Gold engine coolant – See dealer Inspect accessory drive belt(s) – See dealer Replace PCV valve – See dealer Replace spark plugs – See dealer Replace accessory drive belts (if not replaced within last 100,000 miles) – See dealer Replace rear axle lubricant – See dealer Change automatic transmission/transaxle fluid and filter – See dealer Notes: Prices are shown for illustrative purposes only and may vary based on required fluid quantities and other conditions. Information in this document is current as of January 07, 2010 and could change in the future.

Related Content:

replace radiator on hummer h3, 2006 nissan frontier cat replacement, hydraulic parking brakes on drive shaft, how to replace cat 05 frontier, how to replace an alternator on a 2006 honda pilot, how to replace a alternator on a 2006 honda pilot, how to change starter in 2006 chevy cobalt 2 2, ford explorer 2006 linkage repair, 2006 saturn ion maintenance recommendations, 2006 mercury 5 1 inboard starter smoking

1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

steering pressure hose replacement f250 - 7 3 - 4wd, how to remove trumpet off of ford 2000 tractor, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, 98 amigo isuzu how to remove power steering pump, how to replace 2003 impala power steering pump, schematic for 99 taurus power steering, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, youtube replace the hub on a meritor ff981 axle, how to change power steering pump 2009 acada

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

0

Filed Under (More Manuals) by admin on 07-07-2012

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

Related Content:

2007 buick lacrosse window relay, chevy hhr evap, bypass anti-theft 2007 silverado, 200lolds aleroraditor system, 4t65e service manual online, 2007 kia rio service manual, w584a lincoln, 2007 Chevy Colorado Gas Tank Seal replace, schematic for front brakes on 2005 Buick Rendezvous, pontiac 2007 g6 remove radiator cover

2001 – 2006 TOYOTA Sequoia BACK DOOR POWER WINDOW INOPERATIVE

0

Filed Under (Toyota Manuals) by admin on 11-01-2012

download
BACK DOOR POWER WINDOW INOPERATIVE – EL007-06 June 14, 2006 Page 2 of 6 ITEM NO. SPECIAL SERVICE TOOLS (SSTs) PART NUMBER QTYDRW** 1 Plastic Pry Tool Set* NOTE: All components from this kit/set are required 00002-06000-01 1 21 *Essential SSTs. **Refers to drawer number in SST Storage System. NOTE: Additional SSTs may be ordered by calling SPX/OTC at 1-800-933-8335. 1. Disconnect the negative (-) terminal of the vehicle battery. NOTE: Any time the negative (-) battery terminal has been disconnected, systems requiring initialization will need to be re-initialized after the negative (-) battery terminal has been reconnected. 2. Open the back door and leave open. 3. Using the plastic pry tool, remove the back door garnish center. 4. Using the plastic pry tool, remove the left and right back door side garnish panels. Required SSTs Repair Procedure : 5 Clips : 3 Clips BACK DOOR POWER WINDOW INOPERATIVE – EL007-06 June 14, 2006 Page 3 of 6 5. Remove the strap cover, bolt, and pull strap. NOTE: To remove the strap cover, push it toward the back door window as shown in the illustration. 6. Remove the back door trim board. A. Insert the plastic pry tool between the back door trim board to release the clips retaining the back door trim. NOTE: Be careful NOT to damage the back door and back door trim board. B. Release each clip as shown in the illustration. 7. Disconnect both connectors to the back door ECU and both clips holding the wire harness to the large service cover. 8. Remove both of the back door service hole covers. For 2001 – 2004 model year Sequoia vehicles, go to step 11. For 2005 – 2006 model year Sequoia vehicles, continue to step 9. 9. For 2005 – 2006 model year Sequoia vehicles ONLY: Remove the multiplex network door ECU. Using a drill of less than 3.2 mm (0.126 in.), drill out the two (2) rivet heads. HINT: Gently and vertically put the drill to the rivets and cut the rivet flanges. CAUTION: Take care as the cut rivets may be HOT. 10. For 2005 – 2006 model year Sequoia vehicles ONLY: Install the replacement multiplex network door ECU and rivets

Related Content:

2006 pt cruiser install guide, 2006 mercury eatc repairs, 2006 kia rio service manual free download, Back Door Power Window Inoperative - EL007-06 - June 14 2006, remove transmission control module G500, where to fine starter location in 2006 chevy calorando, 2006 npr freon capacity, 2006 chevy colorado service manual free, 2006 Chrysler 300c srt8 service and repair manual pdf download, enigine diagram for 2006 grand prix

2004 Chevrolet TrailBlazer Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Repair Manual

0

Filed Under (Chevrolet Manuals) by admin on 18-02-2012

download
This bulletin is being revised to add model years and provide important repair information. Please discard Corporate Bulletin Number 04-08-49-015 (Section 08 — Body and Accessories). Condition Some customers may comment on a noise coming from the instrument panel cluster (IPC) while driving or on initial start-up. Instrument clusters may contain stepper motor gages that can make noise during the following conditions: Subject: Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Models: 2003-2005 Buick LeSabre 2003-2007 Buick Rendezvous 2004-2005 Buick Rainier 2003-2006 Cadillac Escalade, Escalade ESV, Escalade EXT 2003-2005 Chevrolet Cavalier, Impala, Monte Carlo 2003-2006 Chevrolet Avalanche, Suburban, Tahoe, TrailBlazer EXT 2003-2007 Chevrolet Silverado Classic, TrailBlazer 2003-2007 Chevrolet Kodiak Models 2004-2006 Chevrolet SSR 2003-2006 GMC Envoy XL, Yukon, Yukon XL 2004-2005 GMC Envoy XUV 2004-2007 GMC Envoy 2003-2007 GMC Sierra Classic 2003-2004 Oldsmobile Bravada 2003-2005 Pontiac Aztek, Bonneville, Sunfire 2003-2005 HUMMER H2 Attention: Appropriate repair is based on vehicle build date. Use GMVIS to determine the vehicle build date. • Initial startup (gages zero/reset)

Related Content:

2004 buick rendezvous repair manual, service manual for 2004 audi a6 2 7t quattro, 2003 gmc sierra service repair manual, stepper motor for 2004 chevy trailblazer, free 2003 gmc envoy shop manual, repairing center console for 2005 f150, repair manual mitsubishi diamante, 2004 chevy malibu wiring diagrams for EVAP system, manual for 2008 pontiac g5, programming 2004 tahoe instrument cluster

2004 – 2006 Toyota Sienna Vehicles Equipped w/ Power Back Door (Power Rear Liftgate) Repair Manual

0

Filed Under (Toyota Manuals) by admin on 22-06-2012

download
Certain 2004 – 2006 Model Year Sienna vehicles equipped w/Power Back Door (Rear Liftgate) Q1: What is the condition? A1: Toyota has determined that the gas struts used to help lift and support the Power Rear Liftgate in certain 2004 through 2006 model year Sienna vehicles could be wearing out sooner than expected. As the gas struts deteriorate, the performance of the Power Rear Liftgate will begin to degrade, and the Power Rear Liftgate will operate more slowly than when the gas struts were new. Only Sienna vehicles equipped with the Power Rear Liftgate are involved. Q2: Are there any warnings that this condition exists? A2: Owners may notice that the Power Rear Liftgate will not remain in the open position. If not repaired, the gas struts may not be able to support the weight of the liftgate when it is open, and eventually, the gas struts could deteriorate to the point that the liftgate will fall about ten inches after it reaches the fully open position, at which point the power motor will engage and power the liftgate to the fully closed position. This condition may cause injury to a person who is struck by the liftgate when it falls or when it is closing. Q3: When were these vehicles produced, and how many vehicles are involved? A3: Only certain 2004 through 2006 model year Sienna vehicles equipped with the Power Rear Liftgate, produced between January 2003 and December, 2006 are involved. Approximately 196,000 vehicles are involved nationwide.

Related Content:

2006 pontiac torrent liftgate release switch, 2004 Toyota Sienna Manual PDF, 2004 sienna engine firing order, 2006 cadillac escalade liftgate problem blows fuses, free repair manual for a 2004 toyota sienna, owners manual for a 2006 scion xb, pt cruiser owners manual 2006, replace 2007 pacifica liftgate assists

2000 – 2006 TOYOTA TUNDRA SPORT DUTY UNDERCARRIAGE MOUNTING INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 18-03-2012

download
2000 – 2006 TOYOTA TUNDRA SPORT DUTY UNDERCARRIAGE MOUNTING INSTRUCTIONS The mounting procedure outlined below covers the 2000 – 2006 Toyota Tundra trucks. You will need to refer to the illustrations and familiarize yourself with each of the undercarriage components and their relative position to each other. Then proceed as follows: 1. Begin by removing the bolts holding the skid plate to the bottom of the bumper and the rear cross member. Remove the skid plate. Some vehicles are equipped with an additional skid plate that wraps up in front of the bumper. This skid plate must be removed also. 2. Remove the bolts connecting the tow hook, tie down brackets, and skid plate brackets (Refer to Figure 1) to the bottom of the frame. The bolts and tow hook will be used in the undercarriage installation. 3. Assemble Driver Side Push Beam Support Plate (62B) to the bottom of the driver side frame rail. Begin by installing the bolts removed in Step 2 into the two holes in the bottom of Diver Side Push Beam Support Plate (62B) . Tighten these two bolts. Next, drill the inside and outside frame wall for the upper hole in Driver Side Push Beam Support Plate (62B). Install one ½”-13 X 4-1/2″ Hex Head Bolt (D) and one ½”-13 Lock Nut (B) in the drilled hole. Tighten this bolt. 4. Repeat Step 3 on the passenger side frame rail. Include the tow hook over Passenger Side Push Beam Support Plate (62A). The skid plates, tie down brackets, and skid plate brackets (See Figure 1) will no longer be used but should be retained in case the undercarriage is ever removed. 5. Install Push Beam Assembly (62) between Push Beam Support Plates (62A & 62B) using eight ½”-13 X 1-1/2″ Hex Head Bolts (A) and eight ½”-13 Lock Nuts (B). For Light Duty Plow applications, the center of the receiver hole in Push Beam Assembly (62) should be 14-1/2″ from the ground. Leave hardware finger tight. 6. Assemble Angle Bracket (75) to the back of Push Beam Assembly (62) using four ½”-13 X1- 1/2″ Hex Head Bolts (A) and four ½”-13 Lock Nuts (B). Leave hardware finger tight. 3 7. Assemble the rear portion of Angle Bracket (75) to the truck’s cross member using two Nut Plates (101), two ½” Split Lock Washers (C) and two ½”-13 X 1-1/2″ Hex Head Bolts (A) . Nut Plates (101) must be inserted into the cross member through the large hole in the rear of the cross member. 8. Tighten all hardware beginning at the rear of Angle Bracket (75) and working forward. 9. With all undercarriage parts in place, securely fasten all mounting hardware. It is important that all fasteners be properly torqued (see Fig. 3) to assure a safe operating plow. Re-tighten all fasteners after 2 hours of plowing.

Related Content:

diagram of 2006 honda oddessey, how to remove skid plate on 2012 tundra, removing Driveshaft 2006 Tundra

2006 TOYOTA RAV4 TOWING HITCH INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 17-03-2012

download
TOYOTA RAV4 2006 TOWING HITCH Section II Installation Procedure Page 2 of 7 pages Issue: A 10/11/05 Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Prepare for Installation. (a) Verify kit contents (b) Wear Safety Glasses. (c) Raise Vehicle . (d) Caution Muffler might be hot 2. Remove Rear Bumper Fascia (a) Remove (2) Phillips head screws (A) from both sides of the rear fascia (Fig. 2-1). (b) Remove (7) push pins (A) on edges of fascia (Fig. 2-2) (c) Remove (2) Phillips head screws (B) from bottom of fascia (Fig. 2-2). (d) See Fig. 2-3 for removal of fastener (C). Fig. 2-1 Rear Tire A A (Drivers Side) – Phillips screwdriver A A A A A C A A B B – Phillips screwdriver – Straight shank screwdriver Fig. 2-2 TOYOTA RAV4 2006 TOWING HITCH Section II Installation Procedure Page 3 of 7 pages Issue: A 10/11/05 (e) Remove (1) 10 mm hex head bolt (C) from right hand (RH) side of fascia. (Fig. 2-3) (f) With one person on each end, remove fascia from vehicle. Store in a safe place to avoid damage during installation. 3. Remove Vehicle Tie Down (a) Remove (2) M12 Bolts and vehicle tie down (A) from the left hand (Drivers Side) rear of vehicle (Fig. 3-1). (b) Dispose of bracket and (2) bolts. 4. Detach Muffler (a) Protect exhaust tip with a rag or protective tape during installation of hitch (Fig. 5). (b) Detach muffler from exhaust hangar (Fig. 5) 5. Install Bumper Brackets (a) Remove M8 bolts from the vehicle bumper beam, and install (RH) and (LH) bumper brackets with (3) OE supplied M8 bolts, each with a lock washer and a flat washer (Fig. 5-1). Do not tighten at this time. 6. Install Hitch (a) Lift hitch into place (requires 2 people) and install the (3) M12 x 35 bolts into the (3) weld nuts in the bottom of the frame rails (Fig. 6-1). (b) Loosely secure the middle bolts first, then the (2) forward and aft bolts on each side. (c) Do not tighten bolts at this time. 7. Install Drivers Side Brackets (a) Install LH Frame Bracket (A) to the side of the frame rail using (2) of the M12 x 35 bolts (Fig. 7-1). NOTE: Excess body sealant may require removal of sealant before continuing installation Protect any bare areas with 3MTM Autobody sealant. (b) Install LH Support Bracket (B) to Driver’s Side of Hitch (C), and to bottom of LH Frame Bracket using (4) M12 x 35 bolts. Do not tighten (Fig. 7-1). (c) Fasten LH Support Bracket (B) to LH Bumper Bracket (D) using (4) M12 x 35 bolts. Do not tighten (Fig. 7-1)

Related Content:

how to fix a rav 4 rear bumper, 2006 rav4 front bumper install instrucions, how to replace a rave 4 rear bumper cover, how to install lift supports, HOW TO FIX A DANGLING FRONT SIDE BODY OF TOYOTA RAV4?, how do you remove front bumper 2008 toyota rav4, diy replace 2002 rav 4 rear bumper, 2009-2012 toyota rav4 front bumper removal, 2007 Toyota Rav4 radiator support access cover fastener, installation instructions 2002 rav 4 rear bumper

2006 TOYOTA YARIS ELECTRONIC CRUISE CONTROL KIT INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 15-03-2012

download
TOYOTA YARIS 2006 ELECTRONIC CRUISE KIT Section II – Installation Procedure Form #5007, Rev. B, 05-23-06 Page 2 of 7 Section II – Installation Procedure A. Pre-Installation Suggestions 1. It is advisable to disconnect the negative battery cable for 3 minutes before beginning installation, to avoid unintended air bag deployment. Note and record any anti-theft radio codes prior to disconnecting . (figure 1) 2. Remove driver side small object box, lower dash panel, and steering column cover for easy access. B. Install Electronic Modules 1. There are two electronic modules. The larger one is the Cruise Control Module and the smaller one is the Switch Interface Module . 2. Apply the larger supplied piece of double- sided adhesive tape to the Cruise Control Module, and the smaller piece of double-sided tape to the Switch Interface Module. 3. Assemble 20-pin connector from Main Wiring Harness onto mating connector of Cruise Control Module. Apply the 10 and 4 pin connectors from Pedal Interface Harness to mating connector on Switch Interface Module. Warning: Be sure to use the 4 pin connector that is on the same side of the wire harness fuse as the 10 pin connector. Failure to do so could damage vehicle’s ECM. See the picture insert in Figure 2 for further guidance. 4. Locate the linked harness between the Cruise Control and Switch Interface Modules. Connect the four pin mating connectors. 5. Place the Cruise Control Module on the back side of the main J/B. Then place the Switch Interface Module on the inside wall of the driver-side dash left of the J/B .(figure 2,3) 6. Route the Pedal Interface Harness through steering column and down to the accelerator .(figure 4 ) TOYOTA YARIS 2006 ELECTRONIC CRUISE KIT Section II – Installation Procedure Form #5007, Rev. B, 05-23-06 Page 3 of 7 7. Locate the 6 pin plug and mate connectors on the Pedal Interface Harness. Remove the accelerator 6-pin connector and apply to mating connector of the Pedal Interface Harness. Apply the other connector to the accelerator .(figure 5) C. Wiring Connections (figures 6-12) 1. Use the supplied self-stripping connectors (T- taps) from hardware pack to apply a T-tap onto the following J/B wires

Related Content:

what duse is cruise control 2007 volvo xc90, wiring diagram for toyota cressida pdf

Related Content:

antenna repair torrent, 04 impaia p0455, 2006 chev impala remote lock location, how to remove 2007 dps rear seat, how to remove back seat in 2007 Buick lucerne, how to remove the back seat on buick lucerne 2006 v6, how to repace autana on 2000 tacoma, is the keyless entry module wiring in all 02 monte carlos, partially blown channel plate gasket 2001 chevy malibu, remove back seat 2008 dts