Skip to content

how to change the belt tensioner chrysler town country 2007 van

You search PDF repair manual about how to change the belt tensioner chrysler town country 2007 van, if there are search results will appear below. If search results do not exist, please search by others keyword.

1998 Chrysler Town And Country LX SERPENTINE BELT SLIPS OFF IDLER PULLEY REPAIR PROCEDURE

download
REPAIR PROCEDURE This repair is compatible with DaimlerChrysler’s Mobile Service Program and does not require hoists or other full service facility special equipment. 1. Remove the serpentine belt from around the idler pulley by rotating the tensioner clockwise ( Fig. 3 ). 2. Remove the purge duty cycle solenoid and wiring harness from the right side engine mount. 3. Remove the two right side engine mount insulator vertical fasteners and loosen the horizontal fastener. DO NOT remove the large nut in the center of the core of the insulator ( Fig. 4 ). 4. Remove the load on the engine mount by carefully supporting the engine with a floor jack. 5. Remove the vertical and horizontal fasteners from the engine side bracket. Remove the engine mount assembly. 6. Remove the idler pulley from the engine mounting bracket. ( Fig. 3 ). 7. Remove the engine mounting bracket. 8. Install a new engine mounting bracket. Torque the fasteners to 40-68 N.m (30-50 ft-lbs.). 9. Install the idler pulley to the engine mounting bracket. Torque the fastener to 40-68 N.m (30-50 ft-lbs.). 10. Properly route and position a serpentine belt onto all pulleys except the idler pulley (Use a new belt if there is any evidence of damage to the original one). 11. Rotate the belt tensioner clockwise until the belt can be installed onto the idler pulley. Slowly release the belt tensioner. 12. Install the engine mount; torque the assembly in the following order, engine mount to rail fasteners 68 N.m (50 ft-lbs.), vertical fastener 102 N.m (75 ft-lbs.), and horizontal fastener 150 N.m (111 ft-lbs.). 13. Install the purge duty cycle solenoid to the engine mount. 14. Start the vehicle and let it run for one minute then turn the engine off. 15. Verify the serpentine belt is properly aligned ( Fig. 1 ) 16. If the serpentine belt has moved toward the outboard edge of the idler pulley, further diagnosis will be required. WARRANTY INFORMATION POLICY: Reimbursable within the provisions of the warranty. LABOR OPERATION NO: 07-20-20-96 TIME ALLOWANCE: 0.7 Hrs. FAILURE CODE: P8 – New Par

1997 Chrysler Sebring JXi TIMING BELT REMOVAL AND INSTALLATION MANUAL

download
1. Disconnect negative battery cable from jumper terminal. Raise and support vehicle. Remove right front wheel. Remove accessory drive belt splash shield from right wheelwell. 2. Remove accessory drive belts. Remove right engine support assembly vertical bolts from bottom side of frame rail (timing belt end of engine). 3. Lower vehicle. Place floor jack under vehicle to support weight of engine and transaxle assembly. Remove 3 bolts attaching engine support assembly to engine block bracket. 4. Move the A/C drier aside with hoses attached. Remove coolant reservoir tank. Remove right engine support assembly. Remove 3 bolts attaching engine support bracket to engine block, and remove bracket. 5. Remove crankshaft vibration damper. Remove power steering pump (hoses attached) and bracket from engine block. Remove timing belt covers. 6. Rotate crankshaft to align camshaft and crankshaft timing marks. 7. If reusing old timing belt, mark timing belt direction of rotation for installation reference. Loosen timing belt automatic tensioner bolts. Remove timing belt. Remove automatic tensioner. Installation 2.5L VIN H (Cirrus, Sebring Convertible & Stratus) 1. Place automatic tensioner into vise, and SLOWLY compress plunger. When plunger is compressed into tensioner body, install locking pin through body and plunger holes to retain plunger until tensioner is installed. See Fig. 13 . 2. Index tensioner in vise the same direction as installed. This will ensure proper pin orientation when tensioner is installed in engine.

1993 Mercedes Benz 190E Drive Belt Tensioner Service and Repair Manual

download
Service and Repair Notes NOTE : The belt tensioning device has been modified during production, tensioner version may vary from one vehicle to another. Early engines may be retrofit with later tensioners but requires additional parts. PROCEDURE Remove Poly V-Belt . On Tensioning Devices Without Shock Absorber NOTE : The 1st design of the tensioning device was without a shock absorber. Unbolt fixing bolt (25). Tightening torque: With 19mm hex head 75 Nm (55 ft lbs) . With 17mm hex head 80 Nm (59 ft lbs) . Remove belt tensioner.

2002 Mitsubishi Montero Limited Removing Drive Belt Auto Tensioner/ Aligning Timing Marks

download
Aligning Timing Marks (2001-02 Montero) Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. Installation (2001-02 Montero) 1. Place auto-tensioner in soft-jawed vise to SLOWLY compress the push rod. If there is a plug at the base of the auto-tensioner body, place flat washer around plug so it will not contact vise jaw. 2. Slowly compress auto-tensioner push rod until holes in push rod and auto-tensioner housing are aligned. Insert a locking pin into the alignment holes. Install auto-tensioner on engine. 3. Ensure all timing marks are still aligned. See Fig. 11 . Install timing belt on crankshaft sprocket, idler pulley, left bank camshaft sprocket, water pump pulley, right bank camshaft sprocket, and tensioner CAUTION: Never compress the auto-tensioner too fast, or the push rod will be damaged. WARNING: Right bank camshaft can easily turn from applied spring pressure. Be careful not to pinch fingers when installing timing belt. 2002 Mitsubishi Montero Limited MITSUBISHI 3.5L V6 – SOHC many waters gallery pulley. Take all slack out of timing belt. 4. Loosen the tensioner pulley center bolt. Using Tensioner Pulley Wrench (MD998767), rotate tensioner pulley against timing belt. Temporarily tighten tensioner pulley center bolt. Using Crankshaft Pulley Spacer (MD998769), turn crankshaft 1/4 turn counterclockwise. Turn crankshaft 1/4 turn clockwise. Ensure all timing belt marks are still aligned. 5. Loosen tensioner pulley center bolt. Position tensioner pin holes at bottom of tensioner. Install Tensioner Pulley Wrench (MD998767) on tensioner pulley. See Fig. 12 . Using torque wrench, apply 39 INCH lbs. (4.4 N.m) of torque (counterclockwise direction) to tensioner pulley. Tighten tensioner center bolt to specification while holding tensioner pulley stationary. See TORQUE SPECIFICATIONS . 6. Remove locking pin from auto-tensioner. Turn crankshaft 2 revolutions clockwise and align all timing marks. DO NOT rotate counterclockwise. 7. Wait for at least 5 minutes, then check auto-tensioner push rod protrusion. To check push rod protrusion, measure clearance between body of auto-tensioner and bottom of tensioner pulley bracket arm. Clearance should be 0.15-0.20″ (3.8-5.0 mm). If protrusion is not correct, repeat timing belt tensioning procedure. Ensure all timing marks are aligned. 8. Install timing belt covers. See Fig. 10 . Install crankshaft pulley. Tighten crankshaft pulley bolt to specification. See TORQUE SPECIFICATIONS . Install accessory mount assembly on front of engine. See Fig. 13 . See TORQUE SPECIFICATIONS . To install remaining components, reverse removal procedures. See Fig. 7 and Fig. 8 . Adjust drive belts to proper tension. 9. When filling cooling system, use 50/50 mix of coolant and water. Open bleed screw on top of thermostat housing. Slowly fill cooling system until coolant flows out of bleed hole. Install bleed screw. Start engine and run to normal operating temperature. Race engine to 3000 RPM several times. Stop engine. After engine cools, refill radiator and coolant reservoir tank.

2006 HONDA Civic 2/4-Door Drive Belt Auto-Tensioner Pivot Bolt Replacement

download
REPAIR PROCEDURE 1. From above the engine, set a long-handled, boxed- end wrench on the drive belt auto-tensioner. Slowly turn the wrench counterclockwise, then remove the drive belt. NOTE: On vehicles without A/C, the drive belt will be reused. 2. Insert a pulley holder (see REQUIRED SPECIAL TOOLS) into one of the holes in the water pump pulley at the 12 o’clock position. The tool holds the pulley so you can loosen or tighten the pulley bolts. 3. Remove the water pump pulley (three bolts). 4. Remove the pivot bolt from the drive belt auto- tensioner. NOTE: In rare cases, the pivot bolt may be broken. If this has happened, remove the auto-tensioner, then remove the shank of the pivot bolt with Vise Grips or by drilling it out. Do not try to repair the engine block using a TIME-SERT. If you can’t remove the shank of the pivot bolt, you would need DPSM approval to install an engine short block assembly. WITHOUT A/C WITH A/C WITHOUT A/C