how to change thermostat v6 prado

You search PDF repair manual about how to change thermostat v6 prado, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to change thermostat v6 prado Direct Download speed 5432 Kb/s

  how to change thermostat v6 prado Full Version speed 8172 Kb/s



2000 Pontiac Montana THERMOSTAT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Pontiac Manuals) by admin on 07-02-2012

download
Removal & Installation 1. Remove the air cleaner and duct assembly. See Fig. 10 . Drain the coolant until the coolant level is below the thermostat. See COOLING SYSTEM BLEEDING . 2. Remove the crossover exhaust pipe. See Fig. 11 . Remove the radiator hose from the thermostat housing. 3. Remove the thermostat housing bolts and clean any sealer from the bolt threads. See Fig. 12 . Remove the thermostat housing and gasket. 4. Remove the thermostat. Inspect and clean the mating surfaces. 5. Install the thermostat housing and gasket. Install RTV sealer (GM P/N 1052366) to the thermostat housing bolt threads. Install the thermostat housing bolts. See TORQUE SPECIFICATIONS . 6. To complete installation, reverse removal procedure. Fill the cooling system. Inspect the cooling system for leaks. Repair as necessary.

Related Content:

2000 montana pontiac manual, 2000 pontiac montana radiator removal, 2000 pontiac montana repair manual pdf, 2011 chevy cruze thermostat housing, 2012 chevy cruze thermostat location, changing the thermostat gas mileage on a hummer h3, how to install a radiator in a 2002 pontiac montana, isuzu rodeo thermostat location, location of thermostat 09 3 5 pontiac G6

2002 Pontiac Grand Prix GT THERMOSTAT REPLACEMENT (3.1 L) MANUAL

0

Filed Under (Pontiac Manuals) by admin on 08-05-2012

download
THERMOSTAT REPLACEMENT (3.1 L) Tools Required J 38185 Hose Clamp Pliers Removal Procedure 1. Remove the air cleaner intake duct. Refer to AIR CLEANER INTAKE DUCT . 2. Partially drain the cooling system. Refer to Draining and Filling Cooling System . 3. Use the J 38185 in order reposition the hose clamp from the water outlet housing. 4. Remove the radiator inlet hose from the water outlet housing. 5. Remove the exhaust crossover pipe. Refer to EXHAUST CROSSOVER PIPE REPLACEMENT (3.1L) or EXHAUST CROSSOVER PIPE REPLACEMENT (3.8L) Fig. 74: Radiator Inlet Hose & Water Outlet Housing Courtesy of GENERAL MOTORS CORP. 6. Remove the water outlet housing bolts. 7. Remove the water outlet housing and gasket. Fig. 75: Water Outlet Housing & Bolts Courtesy of GENERAL MOTORS CORP. 8. Remove the thermostat. 9. Clean the water outlet housing mating surfaces Fig. 76: Thermostat & Water Outlet Housing Courtesy of GENERAL MOTORS CORP. Installation Procedure 1. Install the thermostat. 3. Install the water outlet housing bolts. Tighten Tighten the water outlet housing bolts to 25 N.m (18 Ib ft). 4. Install the exhaust crossover pipe. Refer to EXHAUST CROSSOVER PIPE REPLACEMENT (3.1L) or EXHAUST CROSSOVER PIPE REPLACEMENT (3.8L) . 5. Install the radiator inlet hose to the water outlet housing.

Related Content:

replacing thermostat izusu axiom, 2001 oldsmobile alero 3 4l thermostat removal, 2002 concorde themostat diagram, 2002 pontiac grandprix 3 8 thermostat replacement, 99 explorer changing thermostat, Car Thermostat Diagrams 2008 Pontiac G6, how do you change a intake gasket on a 2001 pontiac grand prix gt, where is the thermostat in a sienna 2005, where is thethermostate on a pontaic mini van

Ford SVT Contour/ Mercury 2.5L V-6 Cougar (5 Speed Manual Transmission Only) Supercharger System Installation Manual

0

Filed Under (Ford Manuals) by admin on 24-05-2012

download
1998-2000 FORD SVT CONTOUR/ MERCURY 2.5L V-6 COUGAR Installation Instructions For best performance and continued durability, please take note of the following key points: 1. Use only premium grade fuel 92 octane or higher (R+M/2). 2. The engine must have stock compression ratio. 3. If the engine has been modified in any way, check with Vortech prior to using this product. 4. Always listen for any sign of detonation (pinging) and discontinue hard use (no boost) until problem is resolved. 5. Perform an oil and filter change upon completion of this installation and prior to test driving your vehicle. Thereafter, always use a high grade SF rated engine oil or a high quality synthetic, and change the oil and filter every 3,000 miles or less. Never attempt to extend the oil change interval beyond 3,000 miles, regardless of oil manufacturer’s claims as potential damage to the supercharger may result. 6. Before beginning installation, replace all spark plugs that are older than 1 year or 10,000 miles with original heat range plugs as specified by the manufacturer and reset timing to factory specifications (follow the procedures indicated within the factory repair manual and/or as indicated on the factory underhood emissions tag). Do not use platinum spark plugs unless they are original equipment. Change spark plugs at least every 20,000 miles and spark plug wires at least every 50,000 miles. TOOL & SUPPLY REQUIREMENTS: •Factory Repair Manual •3/8″ Socket and Drive Set: SAE & Metric •1/2″ Socket and Drive Set: SAE & Metric •3/8″ NPT Tap and Handle •Adjustable Wrench •Open End Wrenches: 3/8″, 7/16″, 1/2″, 9/16″ •Center Punch •Ford Springlock 3/8″ Fuel Fitting Disconnect Tool •5 Quarts SH/CF Rated Quality Engine Oil •Oil Filter and Wrench •Flat #2 Screwdriver •Phillips #2 Screwdriver •Heavy Grease •Silicone Sealer •Drill Motor •1/8″, 3/16″, 27/64″ Drill Bits •9/16″ Rota Broach Tool (also available from Vortech) •Molylube •Wire Strippers and Crimpers •Utility Knife If your vehicle has in excess of 10,000 miles since its last spark plug change, then you will also need: •Spark Plug Socket •NEW Spark Plugs

Related Content:

free repair manual for 1998 Ford Contour SVT, repair manual for 1998 Ford Contour SVT, 97 Ford Thunderbird Repair Manual, 98 contour svt 2 5 alternator diagram, downloadable owners manual 1998 ford contour, Ford five hundred spark plug change, how to change thermostat on a 1998 ford contour, ou change the antifreeze in a 2008 G6 3 9

2006 Ford Explorer Scheduled Maintenance Guide

0

Filed Under (Ford Manuals) by admin on 12-02-2012

download
Scheduled Maintenance: 2006 Ford Explorer Driving Condition: Normal Condition Engine Displacement Transmission Fuel Cylinders Drivetrain 4.0 L Automatic Flexible 6 RWD ded Maintenance Mileage: Every 5,000 15 30 45 60 75 90 100 105 120 135 150 Value Package Price: See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer Change engine oil and replace oil filter (Up to 5 quarts of oil. Perform at specified mileage interval or every 6 months, whichever occurs first) – See dealer Perform multi-point inspection – See dealer Rotate and inspect tires; check wheel end play and turning noise – See dealer Inspect automatic transmission fluid level (if equipped with underhood dipstick) – See dealer Inspect brake pads/shoes/rotors/drums, brake lines and hoses, and parking brake system – See dealer Inspect engine cooling system and hoses – See dealer Inspect and lubricate all non-sealed steering linkage,ball joints,suspension joints,half and drive-shafts and u-joints – See dealer Inspect complete exhaust system and heat shields – See dealer Replace engine air filter – See dealer Replace fuel filter – See dealer Inspect 4×2 front wheel bearings; replace grease and grease seals, and adjust bearings – See dealer Change Premium Gold engine coolant – See dealer Inspect accessory drive belt(s) – See dealer Replace PCV valve – See dealer Replace spark plugs – See dealer Replace accessory drive belts (if not replaced within last 100,000 miles) – See dealer Replace rear axle lubricant – See dealer Change automatic transmission/transaxle fluid and filter – See dealer Notes: Prices are shown for illustrative purposes only and may vary based on required fluid quantities and other conditions. Information in this document is current as of January 07, 2010 and could change in the future.

Related Content:

replace radiator on hummer h3, 2006 nissan frontier cat replacement, hydraulic parking brakes on drive shaft, how to replace cat 05 frontier, how to replace an alternator on a 2006 honda pilot, how to replace a alternator on a 2006 honda pilot, how to change starter in 2006 chevy cobalt 2 2, ford explorer 2006 linkage repair, 2006 saturn ion maintenance recommendations, 2006 mercury 5 1 inboard starter smoking

1994 Chevy Truck C 1500 Truck 2WD Tune-up and Engine Performance Checks/ Ignition-Timing Connector Location Change Manual

0

Filed Under (Chevy Manuals) by admin on 06-05-2012

download
SUBJECT: TIMING CONNECTOR LOCATION CHANGE MODELS: 1994 CHEVROLET AND GMC C/K TRUCKS WITH GASOLINE ENGINES The timing connector, which can be disconnected to return engine timing to base for adjustment purposes, has been moved from the engine compartment to inside the cab. This new location is not currently reflected in the Service or Owner’s Manual. The new location is under the dash directly below the glove compartment. The tan/black wire is routed for a short distance outside of a large wiring harness. This large harness is routed between the heater blower motor and evaporator case. The timing connector is taped to the wire bundle (Figure 1)

Related Content:

99 F150 C202, 1994 chevy truck electrical troubleshooting, mlps wire configuration for 1994 f150, pdf 1994 chevrolet chevy van 1500 repair manual

1999 Ford Escort/ Tracer Cylinder Head Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 24-04-2012

download
Removal 1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 . 2. WARNING: Fuel supply lines will remain pressurized for long periods of time after engine shut down. This pressure must be relieved before disconnecting any fuel lines or fuel system components. Relieve the fuel system pressure. For additional information, refer to Section 310-00 . 3. Remove the engine air cleaner outlet tube. For additional information, refer to Section 303-03 . 4. Remove the timing belt. For additional information, refer to Timing Drive Components—Timing Belt in this section. 5. Remove the vacuum hoses at the: * positive crankcase ventilation (PCV) valve (6A666). * throttle body (9E926). * intake manifold (9424). * fuel pressure sensor. 6. Disconnect the fuel charging wiring (9D930) electrical connectors at main engine connector. 7. Disconnect the crankshaft position (CKP) sensor electrical connector. 8. Disconnect the fuel line. For additional information, refer to Section 303-04 . 9. Remove the power steering pump (3A674) and bracket as an assembly. For additional information, refer to Section 211-02 . 10. Remove the generator (GEN). For additional information, refer to Section 414-02 . 11. Remove the oil level indicator tube (6754). For additional information, refer to Oil Level Indicator and Tube in this section. 12. Disconnect the heater hoses. For additional information, refer to Section 412-02 . 13. Lower the vehicle. 14. Disconnect the upper radiator hose (8260) from the thermostat housing water hose connection. For additional information, refer to Section 303-03 . 15. Remove the camshafts (6250). For additional information, refer to Camshaft in this section. 16. Remove the ignition coil (12029) and bracket. For additional information, refer to Section 303-07 . 17. Remove the water thermostat housing. For additional information, refer to Section 303-03 . 18. Disconnect the knock sensor electrical connector. 19. Remove the generator bracket-to-cylinder head bolt. 20. Remove the bolts and the cylinder head (6049). 21. Remove the cylinder head gasket and discard. Installation WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related components. Highly flammable mixtures are always present and may be ignited, resulting in possible personal injury. 1. CAUTION: Do not use abrasive grinding discs to remove gasket material; use only plastic manual scrapers. Do not scratch or gouge the aluminum sealing surfaces. Clean all gasket material from the mating surfaces on the cylinder head and cylinder block. Clean out the bolt holes in the cylinder block. Inspect the cylinder head for flatness. For additional information, refer to Section 303-00 . 2. Install a new head gasket on the cylinder block. 3. CAUTION: Do not attempt to install the cylinder head assembly without assistance. Installation of the cylinder head assembly requires two people or possible injury may occur. CAUTION: The bolts are torque-to-yield and must be replaced or engine damage may occur. Tighten the bolts in three stages in the sequence shown. * Stage 1: Tighten the bolts to 15-25 Nm (12-18 lb-ft). * Stage 2: Tighten the bolts to 35-45 Nm (26-33 lb-ft). * Stage 3: Tighten the bolts an additional 105 degrees. 4. Install the generator bracket-to-cylinder head bolt. * Tighten to 20 Nm (15 lb-ft). 5. Connect the knock sensor electrical connector. 6. Install the thermostat housing. For additional information, refer to Section 303-03 . 7. Install the ignition coil and bracket. For additional information, refer to Section 303-07 . 8. Install the camshafts. For additional information, refer to Camshaft in this section. 9. Connect the upper radiator hose. For additional information, refer to Section 303-03 . 10. Raise and support the vehicle. For additional information, refer to Section 100-02 . 11. Install the heater hoses. For additional information, refer to Section 412-02 . 12. Install the generator and bracket assembly. For additional information, refer to Section 414-02 . 13. Install the power steering pump and bracket assembly. For additional information, refer to Section 211-02 . 14. Connect the fuel lines. For additional information, refer to Section 310-00 . 15. Connect the crankshaft sensor electrical connector.

Related Content:

fleetwood sedona manuals, Honda Civic 2003 number #3 Cylinder pattern, 2001 mitsubishi 3 0 cylinder torque specs, Workshop Manual (WSM) Section 303-04, 4 8 head bolt tightening sequence, workshop information system saab, where is the knock sensor on a 2006 toyota tundra 4 7 v-8 truck, trailblazer front frame section, throttle postioning system in ford five hundred, pdf Ford manual Section 501-02

Q-JET ELECTRIC CHOKE CONVERSION KIT For Converting Hot-Air Choke to Electric Choke INSTALLATION INSTRUCTIONS

0

Filed Under (More Manuals) by admin on 30-12-2011

download
INSTALLATION: 1. In order to properly remove the choke thermostat from the choke housing, an 11/64″drill bit must be used to drill out the rivets attaching the choke cover to the choke housing (See Figure 1) . Drill through choke housing to provide clearance for self-tapping screws provided. 2. Attach the electric choke thermostat to the housing using the supplied self-tapping screws and retaining clips. 3. Connect the supplied choke wire to a 12 volt key-on switched source (Power is on ONLY when ignition key is in the “ON”position), and attach the connector end of the wire to the choke thermostat. NOTE: Always disconnect the battery before making any electrical connections. 4. Using the supplied 1/4″vacuum cap, block off the open vacuum tube on the carburetors choke housing (See Figure 1)

Related Content:

power vacuum kancil, diaphragm valve kancil, location rear wiper washer tank kancil, manual choke conversion instructions

Toyota Landcruiser Prado clutch release bearing Removal And Installation Manual

0

Filed Under (Toyota Manuals) by admin on 25-04-2012

download
1. Withdraw the transmission approximately 30 mm. 2. Insert a flat blade screw driver between the collar and bearing. 3. Twist screw driver 90 degrees and remove the bearing. 1. Locate the clutch release bearing on the gearbox front bearing retainer (snout). 2. Locate the throw out fork on the release bearing. 3. Position transmission to the engine block. 4. Operate the fork opposite direction for clutch release. 5. This will snap the bearing into the cover assembly. F : – 037 Toyota Landcruiser Prado 3.0L 1KD-FTV

Related Content:

engine repair manual for 1kd fte

2008-2010 FORD F-Super Duty DIESEL ENGINES REPEAT RADIATOR LEAK BUILT ON OR BEFORE SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 17-01-2012

download
DIESEL ENGINES REPEAT RADIATOR LEAK BUILT ON OR BEFORE ISSUE ECT temp. Some 2008-2010 F-Super Duty vehicles built on or b. Test results/next steps: before 9/14/2009 and equipped with a 6.4L diesel engine may exhibit repeat radiator leaks due to (1) If EOT is less than 8 °F (4.4 °C) malfunctioning (hyper-extended) high temperature higher than ECT, and the coolant temp thermostats. fluctuates roughly 5 °F (2.7 °C) – the thermostats are okay and do not need ACTION to be replaced. Replace just the Follow the Service Procedure steps to correct the radiator. Refer to WSM, Section 303-03 condition. (Engine Cooling). SERVICE PROCEDURE (2) If EOT exceeds ECT by greater than 8 °F (4.4 °C) or if the ECT readings 1. Verify the coolant leak is from the radiator, refer fluctuate 10 to 12 °F (5.55-6.66 °C) to pinpoint test (PPT) A found in the Workshop roughly every 30 seconds – replace Manual (WSM), Section 303-03. both thermostats and radiator. Refer to 2. Verify the venturi tee is installed. WSM, Section 303-03 (Engine Cooling). a. If installed, confirm it is installed correctly (note – orientation direction on part). 5. If vehicle is not drivable and the coolant leak is found to be from the radiator, remove and b. If not installed, install Venturi Tee Kit on replace both thermostats and radiator. Refer to vehicles built on or before 5/15/2008. WSM, Section 303-03 for both radiator and thermostat removal procedure and approved 3. Prepare the vehicle for a test drive. cooling system draining, filling and bleeding a. If the coolant leak at the radiator is large procedures. enough to cause an unsafe test drive or potential for engine/vehicle damage, proceed PART NUMBER PART NAME to Step 5. 8C3Z-8575-D Thermostat Assembly 8C3Z-8009-B Radiator Assembly b. Before driving the vehicle confirm the 8C3Z-8B379-B Venturi Tee coolant level is at minimum level or above in the degas bottle. If required, add 50/50 WARRANTY STATUS: Eligible Under Provisions Of mix to coolant bottle. New Vehicle Limited Warranty Coverage 4. Test Drive – use an Integrated Diagnostic IMPORTANT: Warranty System (IDS) or equivalent and monitor engine coverage limits/policies are oil temperature (EOT) and engine coolant not altered by a TSB. temperature (ECT) parameter identifiers (PIDS). Warranty coverage limits are determined by the identified causal par

Related Content:

08 f350 radiator replacemnt, how to change thermostat in a 2011 chevy cruze, 2010 F150 Thermostat, f150 ceiling leak, ford focus thermostat does both ends move when hot, replacing saturn aura xe 2008 cooling fan, thermostat housing bolts 2009 focus torkspec

2002 Ford Explorer Sport/ Sport Trac Cylinder Head Removal and installation manual

0

Filed Under (Ford Manuals) by admin on 02-06-2012

download
Removal Both cylinder heads 1. With the vehicle in NEUTRAL, position it on a hoist. For additional information , refer to Section 100-02 . 2. Relieve the fuel system pressure. For additional information, refer to Section 310-00 . 3. Drain the cooling system. For additional information, refer to Section 303-03 . 4. Remove the intake manifold. For additional information, refer to Intake Manifold in this section. 5. Remove the cooling fan shroud. For additional information, refer to Section 303-03 . 6. Remove the accessory drive belt. For additional information, refer to Section 303-05 7. Remove the LH valve cover. For additional information, refer to Valve Cover — LH in this section. 8. Remove the RH valve cover. For additional information, refer to Valve Cover — RH in this section. 9. Disconnect the generator electrical connections. 10. Remove the accessory drive belt tensioner. 11. Remove the bolts and the generator and generator mounting bracket as an assembly. 12. Disconnect the crankshaft position (CKP) sensor electrical connector. 13. Disconnect the wiring harness retainers. 14. Disconnect the water temperature indicator sender unit and the engine coolant temperature (ECT) sensor electrical connectors. 15. Disconnect the exhaust gas recirculation (EGR) tube fitting. 16. Remove the upper heater coolant hose. 1. Squeeze the heater hose clamp. 2. Remove the heater coolant hose. 17. Remove the lower heater coolant hose and position aside. 1. Remove the bolt. 2. Squeeze the hose clamp. 3. Remove the heater coolant hose and position aside. 18. NOTE: The coolant hose will be removed with the thermostat housing. Move the coolant bypass hose clamp off the water pump outlet. 19. Remove the bolts, the thermostat housing and the bypass hose. 20. Remove the bolt and detach the wiring harness retainer. 21. Remove the bolts and position the accessory drive bracket aside.22. Detach the wiring harness retainer. 23. Remove the bolt and the oil level indicator tube. 24. Using the special tool, disconnect the LH spark plug wires from the spark plugs. 25. Disconnect the fuel pulse damper vacuum connector. 26. Remove the four bolts and position the fuel supply tube aside. 27. Remove the bolts and the fuel rail and injectors as an assembly.28. NOTE: Mark each of the roller followers to make sure it is installed in its original position during reassembly. Use the special tool to remove the roller followers. 29. Remove the lower radiator hose. 30. Remove the nut and position the A/C tube bracket aside. 31. Using the special tool, set the No. 1 piston at top dead center (TDC). RH cylinder head 32. Remove the RH fenderwell splash shield. 33. Remove the RH camshaft chain tensioner.

Related Content:

removal of 2000 expedition heater houses, 2001 ford sport trac lower intake gastket diagram, Ford Expedition Heater Hose Removal, ford explorer sport trac thermostat gasket installation, ford explorer valve cover removal, how to Repair 2007 ford expedition rear heater hose, low oil sensor bypass, remove bottom radiator hose on pt cruiser to drain engine block, shop manual 2002 ford sort trac

Related Content:

2000 montana pontiac manual, 2000 pontiac montana radiator removal, 2000 pontiac montana repair manual pdf, 2011 chevy cruze thermostat housing, 2012 chevy cruze thermostat location, changing the thermostat gas mileage on a hummer h3, how to install a radiator in a 2002 pontiac montana, isuzu rodeo thermostat location, location of thermostat 09 3 5 pontiac G6