Skip to content

how to change valve seals 2004 chevy avalanche

You search PDF repair manual about how to change valve seals 2004 chevy avalanche, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Chevrolet Chevy K Silverado – 4WD Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

download
Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 2004 Chevrolet Chevy K Silverado – 4WD 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 8 ft box, the CVS line is routed below the frame crossmember. 2. Install the CVS clip to the frame crossmember. 3. Connect the EVAP CVS line to the canister. 4. If the vehicle is equipped with a 6 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 6 ft box, the CVS line is routed above the frame crossmember. 5. Install the CVS clip to the frame crossmember. 6. Connect the EVAP CVS line to the canister. 7. Connect the CVS electrical connector. 8. Install the harness clip to the canister vent solenoid (CVS) line. 9. Lower the vehicle.

2008 Ford Focus A/T Main Control Valve Body Removal And Installation

download
Disassembly 12 7Z490 Separator plate and gasket assembly 1. Remove the solenoid body bolts and the 13 7A101 Body — control valve lower solenoid body. 14 7R294 Stop — main regulator valve 15 7F445 Retainer plate — main regulator valve 16 7A270 Spring — main fluid pressure regulator valve 17 7C338 Valve — main fluid pressure regulator 18 7G411 Spring — solenoid regulator valve 19 7H392 Valve — solenoid regulator valve 20 7D400 Spring — intermediate servo accumulator 21 7D398 Piston — intermediate servo 2. Remove and discard the solenoid body gaskets. accumulator 22 7G408 Valve — converter pressure relief 23 7G316 Spring — converter regulator valve 24 7M040 Valve — lock up control 25 7Z490 Gasket — solenoid body 26 7G179 Valve — low reverse shift 27 7M040 Valve — 3-4 shift 28 7H148 Shift Solenoid B (SSB) (on/off) valve 29 7H148 Shift Solenoid A (SSA) (on/off) valve ISASSEMBLY AND ASSEMBLY (Continued) 3. Remove and discard the seals. 3. Install the seals. 4. Disassemble the main control valve body. 4. Install a new solenoid body gasket. Assembly 1. Install a new separator plate and gasket assembly. 2. NOTE: Do not fully tighten the bolts at this stage. Assemble the main control valve body and loosely install the bolts. DISASSEMBLY AND ASSEMBLY (Continued) 5. Install the solenoid body and loosely install the 6. Tighten the solenoid body bolts in the sequence bolts. shown. •Tighten to 9 Nm (80 lb-in)

1994 Chevy Truck C 1500 Truck 2WD Tune-up and Engine Performance Checks/ Ignition-Timing Connector Location Change Manual

download
SUBJECT: TIMING CONNECTOR LOCATION CHANGE MODELS: 1994 CHEVROLET AND GMC C/K TRUCKS WITH GASOLINE ENGINES The timing connector, which can be disconnected to return engine timing to base for adjustment purposes, has been moved from the engine compartment to inside the cab. This new location is not currently reflected in the Service or Owner’s Manual. The new location is under the dash directly below the glove compartment. The tan/black wire is routed for a short distance outside of a large wiring harness. This large harness is routed between the heater blower motor and evaporator case. The timing connector is taped to the wire bundle (Figure 1)

DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit)

download
Tighten Tighten the bracket mounting bolt to 12 N?m (106 lb in). Connect the vent valve pipe to the EVAP canister. • Install the two vent valve pipe clips into the existing underbody holes. • Connect the EVAP canister vent valve electrical connector, if equipped. • Attach bulk 5/8″ heater hose to the vent valve port and secure using a clamp. Run a length as needed along the frame rail routing to the area above the transmission. • Cut the hose to determined length and install the supplied filter box. Secure using a clamp. • Remove the transmission support and lower the transmission assembly as necessary to allow for access to the new filter box location using a tie strap. DO NOT pinch or restrict the transmission vent hose. The filter box opening should be pointing downward. • Raise the transmission and reinstall the transmission support. • Tie strap the hose as needed along the frame rail in order to keep the hose away from pinch*points and heat sources. • Lower the vehicle. • 2004-2007 Model Year (Use Service Kit P/N 19152349) Raise the vehicle. Suitably support the vehicle. • Disconnect the EVAP canister vent valve electrical connector. • Disconnect the canister pipe from the vent valve. • Push in the retainer and remove the existing canister vent valve from the fuel tank clip or mounting bracket. Discard the old valve. • Cut back the existing canister pipe approximately 51 mm (2 in) to remove the quick connect end. Crew Cab Short Box Shown Below, Other Configurations Similar Extended Cab Short Box Shown Below, Other Configurations Similar Install the new canister vent valve to the fuel tank clip or mounting bracket. • Cut bulk 5/8″ heater hose to a length of approximately 76 mm (3 in). Install the hose between the vent valve and the canister pipe and secure using clamps. • Attach bulk 5/8″ heater hose to the vent valve port and secure using a clamp. Run a length as needed along the frame rail routing to the area above the transmission. • Cut the hose to determined length and install the supplied filter box. Secure using a clamp. •

2004 Chevrolet TrailBlazer Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Repair Manual

download
This bulletin is being revised to add model years and provide important repair information. Please discard Corporate Bulletin Number 04-08-49-015 (Section 08 — Body and Accessories). Condition Some customers may comment on a noise coming from the instrument panel cluster (IPC) while driving or on initial start-up. Instrument clusters may contain stepper motor gages that can make noise during the following conditions: Subject: Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Models: 2003-2005 Buick LeSabre 2003-2007 Buick Rendezvous 2004-2005 Buick Rainier 2003-2006 Cadillac Escalade, Escalade ESV, Escalade EXT 2003-2005 Chevrolet Cavalier, Impala, Monte Carlo 2003-2006 Chevrolet Avalanche, Suburban, Tahoe, TrailBlazer EXT 2003-2007 Chevrolet Silverado Classic, TrailBlazer 2003-2007 Chevrolet Kodiak Models 2004-2006 Chevrolet SSR 2003-2006 GMC Envoy XL, Yukon, Yukon XL 2004-2005 GMC Envoy XUV 2004-2007 GMC Envoy 2003-2007 GMC Sierra Classic 2003-2004 Oldsmobile Bravada 2003-2005 Pontiac Aztek, Bonneville, Sunfire 2003-2005 HUMMER H2 Attention: Appropriate repair is based on vehicle build date. Use GMVIS to determine the vehicle build date. • Initial startup (gages zero/reset)