chevy malibu power steering control module

You search PDF repair manual about chevy malibu power steering control module, if there are search results will appear below. If search results do not exist, please search by others keyword.



  chevy malibu power steering control module Direct Download speed 5432 Kb/s

  chevy malibu power steering control module Full Version speed 8172 Kb/s



1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, how to change power steering pump 2009 acada, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, 98 amigo isuzu how to remove power steering pump, youtube replace the hub on a meritor ff981 axle, schematic for 99 taurus power steering

1997 Ford Thunderbird/ Cougar Steering Column Removal And Installation Manual

0

Filed Under (Acura Manuals) by admin on 12-04-2012

download
Steering Column Disassembly CAUTION: Do not remove the steering column, steering wheel and air bag module as an assembly from the vehicle unless the column is locked to prevent rotation, or lower end of steering shaft is wired in such a way to prevent the steering wheel from being rotated, as this will damage the air bag sliding contact. 1. Disconnect battery ground cable (14301). Refer to Section 14-01 . 2. Remove steering wheel (3600) as described. 3. Remove steering column from vehicle as described. 4. Remove steering column lower yoke (3N725), steering column upper bearing spring (3520), suspension height sensor control ring (3C131) and steering column bearing tolerance ring (3L539). Lower Steering Column Assembly 5. Remove turn indicator cancel cam (13318) by pushing up with flat-bladed screwdriver. Note direction of flush surface. 6. Remove ignition switch (11572) assembly. 7. Remove bearing retainer (3C610) and steering column upper bearing spring. . Remove steel steering column bearing tolerance ring and steering column bearing sleeve (3518). 9. Remove plastic bearing retainer from ignition switch lock cylinder bore. 10. Remove metal steering column lock housing bearing (3E700) from ignition switch lock cylinder bore. 11. Note position of steering column lock gear (3E717) to actuator lock. Remove steering column lock gear. 12. Remove two pivot bolts. Use caution becausesteering column position spring (3D655) will release when bolts are removed. Remove steering column lock cylinder housing (3511). 13. Remove steering column shaft assembly from steering column. 14. Remove steering column lock lever actuator (3E715) and steering actuator housing (3F723). 15. Remove lower steering column bearing (3517) and steering column lower bearing retainer (3D681).

Related Content:

2005 chevy s-10 streeing colum repair, mgb steering shaft removal, 2008 ford 150 wiring harness box under steering colum, 1993 chevrolet suburban steering column diagram, 1994 chevy s10 steering column wiring, silverado steering column diagram 2005, install steering Center Link on 1989 s10, how to replace steering shaft ujoint for 1992 camry in utube, how to replace shiftetr cloum on 2002 ford f 150, how to remove the steering wheel cover from 04 pontiac grand prix

TOYOTA RAV4 STEERING INTERMEDIATE SHAFT NOISE SERVICE MANUAL

0

Filed Under (Toyota Manuals) by admin on 25-01-2012

download
Repair Procedure 1. Install a steering wheel holder. NOTE: Ensure the wheels are straight and the steering wheel is centered before removing the steering intermediate shaft by installing a steering wheel holder. 2. Remove the column hole cover silencer sheet. Turn back the floor carpet, remove the 2 clips, and remove the column hole cover silencer sheet. Production Change Information Parts Information Repair Procedure STEERING INTERMEDIATE SHAFT NOISE – ST001-08 February 8, 2008 Page 3 of 4 3. Remove the No. 2 steering intermediate shaft assembly. A. Place matchmarks (“a”) on the No. 2 steering intermediate shaft and steering column. B. Remove bolt A and detach the No. 2 steering assembly from the steering gear. C. Remove bolt B and detach the No. 2 steering intermediate shaft from the steering column. 4. Remove the No. 1 steering column hole cover sub-assembly by removing the clamp and disconnecting the column hole cover from the steering gear. 5. Remove the intermediate shaft. Remove the bolt and disconnect the steering intermediate shaft from the steering gear. 6. Install the NEW intermediate shaft onto the steering gear. Torque: 35 Nm (360 kgfcm, 26 ftlbf) 7. Install the No. 1 steering column hole cover sub-assembly onto the steering gear with a NEW clamp. Repair Procedure (Continued) B A a No. 2 Steering Intermediate Shaft Intermediate Shaft STEERING INTERMEDIATE SHAFT NOISE – ST001-08 February 8, 2008 Page 4 of 4 8. Install the No. 1 steering column hole cover sub-assembly by attaching clip B onto the body and installing the No. 1 hole cover onto the body with clip A. NOTE: Make sure that the lip of the No. 1 hole cover is NOT damaged. 9. Install the No. 2 steering intermediate shaft assembly. A. Align the matchmarks (“a”) on steering intermediate shaft and the steering sliding yoke and temporarily install them with bolt B. Torque: 35 Nm (360 kgfcm, 26 ftlbf) B. Ensure the wheels are straight. C. Install the No. 2 intermediate shaft and the intermediate shaft with bolt A. Torque: 35 Nm (360 kgfcm, 26 ftlbf) 10. Install the column hole cover silencer sheet. A. Install the column hole cover plate with the 2 clips. B. Install the floor carpet. 11. Remove the steering wheel holder from the vehicle. 12. Road test the vehicle to verify the repair and confirm that the steering wheel is centered.

Related Content:

07 ford escape intermediate drive shaftpassenger side, 2003-2011 ford crown vic intermediate steering shaft removal, 3024 CAT Rocker Shaft Assembly, 91 Dakota Intermediate Steering Shaft, 92 Dakota Intermediate Steering Shaft, cruze cam cover crack, steering pitman shaft drawing 91 dodge dakota 2 wheel drive

2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

Related Content:

1993 dakota 3 9 fuse diagram, lucas a127 wiring, dodge durango 2002 suspension layout, free 1997 buick regal gs wiring diagrams, 2003 s10 airbag wiring diagram, 1998 Dodge Dakota Service Manual, zimmatic pivot wiring, abs and Anti Theft Passive 2000 mercury cougar, 2000 durango passenger power window switch diagram, Service manual dodge durano 2002 pdf

2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, 2010 f150heater fan speed issues, location of mode motor for 99 honda civic lx, Body Control Module 2007 Silverado, fuse for rear control panel 2006 durango, 2008 colbalt heater core removal, 2001 DODGE RAM 2500 OWNERS MANUAL, repair manual for heater plenum 2011 f-150, 98 taurus heater hose diagram

2005-2008 Honda Odyssey Power Steering Pump Whines , Buzzes, or Hums Repair Manual

0

Filed Under (Honda Manuals) by admin on 16-05-2012

download
Inspect the power steering reservoir. Does one of the 3 ribs on the reservoir cover point toward the reservoir holder? Yes – This vehicle already has the revised power steering reservoir. Continue with normal troubleshooting procedures. No – Go to REPAIR PROCEDURE. REPAIR PROCEDURE 1. Drain the power steering reservoir: •Remove the reservoir from its holder. •Raise the reservoir, and disconnect its return hose. •Drain the reservoir fluid into a suitable container. Take care not to spill any fluid on the body or other parts. Wipe off any spilled fluid immediately. 2. Drain the fluid from the power steering system: •Connect a suitable diameter drain hose to the disconnected return hose. •Hold the end of the drain hose in a suitable container. •Start the engine, and run it at idle while you turn the steering wheel lock-to-lock several times. •When the fluid stops running out of the hose, shut off the engine. •Discard the used fluid. 3. Reinstall the return hose to the reservoir, then reattach the reservoir to its holder. Fill the reservoir to its upper level line with new power steering fluid. 4. Bleed the air from the power steering system: •Start the engine. •With the engine at a fast idle, turn the steering wheel lock-to-lock several times. 5. Check the condition of the fluid in the reservoir: •If the fluid looks contaminated, dark, or discolored, repeat steps 1 thru 5. •If the fluid is clear, go to step 6. 6. Place a suitable container under the vehicle to catch any fluid 7. Replace the power steering fluid reservoir: •Remove the reservoir from its holder. •Disconnect the return hose from the reservoir, and pour the fluid from the reservoir into a container. •Disconnect the outlet hose from the reservoir, and remove the reservoir. •Install a new reservoir in the reverse order of removal. •Fill the reservoir to its upper level line with new power steering fluid. 8. Start the engine, and run it at a fast idle. Turn the steering from lock-to-lock several times to bleed any air from the system. 9. Recheck the fluid level in the reservoir, and add more if needed. Do not fill the reservoir beyond its upper level line.

Related Content:

2011 cruze recall leaking radiator fluid, mazda b2000 electronic ignition pdf, toyota dyna clutch fluid reservoir, washer fluid low silverado trucks

2004 Ford Explorer/Mountaineer Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index Repair Manual

0

Filed Under (Ford Manuals) by admin on 20-05-2011

download
C1963 Stability Control Inhibit Warning ABS Module This DTC is for information only. CLEAR the DTC. REPEAT the self-test. C1991 Module Calibration Failure ABS Module Follow the diagnostic tool directions for the calibration procedure. C1996 Active Yaw Control Disabled ABS Module This DTC will be set if the stability assist system is activated for 15 seconds of continuous operation. CHECK for any major chassis modifications, gross suspension misalignment, or other items that can alter the vehicle tracking dynamics. CLEAR the DTC. REPEAT the self-test. C1998 Module Calibration Not Complete ABS Module Go To Pinpoint Test Q . C2769 (ABS only) Longitudinal Acceleration Sensor Circuit Failure ABS Module CLEAR the DTC. REPEAT the self-test. If DTC C2769 is present, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. C2769 (ABS with stability assist) Longitudinal Acceleration Sensor Circuit Failure ABS Module Go To Pinpoint Test H . C2770 (ABS with Stability Assist) Longitudinal Acceleration Sensor Signal Fault ABS Module Go To Pinpoint Test H . C2770 (ABS only) Longitudinal Acceleration Sensor Signal Fault ABS Module CLEAR the DTC. REPEAT the self-test. If DTC C2770 is present, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. C2777 Sensor Cluster Bus Failure ABS Module Go To Pinpoint Test H . C2778 Sensor Cluster Power Supply Failure ABS Module Go To Pinpoint Test H . U1900 CAN Communication Bus Fault-Receive Error Network Fault Section 418-00 . U1901 CAN Network #2 Communication Bus Fault- Receive Error Network Fault Go To Pinpoint Test H . U2023 Fault received from external node Network Fault Section 418-00

Related Content:

WHERE IS 2002 DAKOTA CENTRAL TIMING MODULE, ABS fault on Tahoe, hino 05 air brake fail abs, where is yaw sensor located on a 2002 ford explorer, how to replace vats module on 1997 buick lesabre, gmc hvac relearn, ford u1901 steering angle sensor, ford u1901 escape, ford relearn after abs sensor trans harsh, FORD FUSION U1900-ABS CAN Communication BUS Fault

1995 Infiniti J30 FUSE PANEL LOCATION AND IDENTIFICATION

0

Filed Under (Infiniti Manuals) by admin on 25-02-2012

download
1 – 10 Amp Hazard Warning * 2 – 15 Amp Audio * 3 – 10 Amp Telephone * 4 – 15 Amp Stop Lamp * 5 – 20 Amp Wiper and Washer * 6 – 15 Amp Cigarette Lighter * 7 – 7.5 Amp Power Antenna * 8 – 10 Amp Door Mirror, Power Seat * 9 – 10 Amp Telephone, Audio * 10 – 15 Amp Blower Motor * 11 – 15 Amp Blower Motor * 12 – 10 Amp Theft Warning System, Air Bag, Key Switch * 13 – 7.5 Amp Clock, Buzzer, Remote Control Door Lock System * 14 – 15 Amp Audio * 15 – 20 Amp Power Window and Door Locks * 16 – 20 Amp Power Window and Door Locks * 17 – Not Used * 18 – 3 Amp (Not Used) * 19 – 7.5 Amp ECM (ECCS Control Module) * 20 – 7.5 Amp Anti-Lock Brake System, Headlamp * 21 – 7.5 Amp Turn Signal Lamp * 22 – 7.5 Amp Air Conditioner * 23 – 7.5 Amp Interior Lights, Footwell Lights, Time Control Unit (TCU) * 24 – 7.5 Amp ECM (ECCS Control Module), Starter Relay * 25 – 7.5 Amp Side Marker, Taillights, Time Control Unit (TCU) * 26 – 7.5 Amp Clock, Glove Box, Dash Illumination * 27 – 20 Amp Audio * 28 – 3 Amp Telephone * 29 – 10 Amp Air Bag System * 30 – 7.5 Amp A/T Control System, ECM (ECCS Control Module) * 31 – 7.5 Amp Warning Light * 32 – 7.5 Amp Electronic Power Steering System, HICAS Control System, Steering Sensor * 33 – 15 Amp Power Seat * 34 – 15 Amp Trunk and Fuel Lid Opener * 35 – 15 Amp (Not Used)

2003-2007 Accord V6 Power Steering Moans or Whines Repair Manual

0

Filed Under (Toyota Manuals) by admin on 02-06-2012

download
SYMPTOM A moan or whine is heard when turning the steering wheel when the engine is cold. There may be air bubbles or foam in the power steering reservoir. The noise usually goes away when the engine warms up. PROBABLE CAUSE Air enters the power steering pump through the inlet joint O-ring. CORRECTIVE ACTION Replace the O-ring on the power steering pump inlet joint. PARTS INFORMATION O-ring: P/N 91345-RDA-A01, H/C 8811010 REQUIRED MATERIALS Honda Genuine Power Steering Fluid: P/N 08206-9002, H/C 3747284 (One container repairs about 12 vehicles.) WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies. Operation Number: 5121B5 Flat Rate Time: 0.3 hour Failed Part: P/N 91345-PAA-A01 H/C 5430681 Defect Code: 07408 Symptom Code: 04201 Template ID: 07-086A Skill Level: Repair Technician Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Parts and Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work. REPAIR PROCEDURE 1. Remove the bolt holding the inlet joint to the power steering pump housing. 2. Place a shop towel under the inlet joint. 3. Twist the inlet joint back and forth until it is loose, then carefully disconnect the joint and point the hose upward to minimize fluid loss. 4. Remove the inlet joint O-ring. 5. Apply power steering fluid to a new O-ring, and install it on the inlet joint. 6. Install the inlet joint, and torque its bolt to 11 N. m (8 lb-ft). 7. Top off the power steering fluid, if needed. Start the engine, and let it idle. Confirm that the noise is gone and that the system is operating properly

Related Content:

corvette c4 tech free pdf, HC - 8811010

2004-2006 Chevrolet Malibu, Malibu Maxx Loss of Power Steering Assist, Power Steering Warning Message Displayed in DIC, IPC/Radio Displays Erratic, DTC C0900, B1325 Set (Replace Ignition Coil/Module Assembly and Add Ground Strap)

0

Filed Under (Chevrolet Manuals) by admin on 10-01-2012

download
Correction Replace the ignition coil/module assembly and add ground strap following the procedure below. 1. Disconnect the ignition coil electrical connector. 2. Disconnect the left side spark plug wires from the ignition coil. 3. Disconnect the right side spark plug wires from the ignition coil. 4. Remove the four bolts attaching the ignition coil to its mounting bracket and remove the ignition coil. 5. Remove the ignition coil from the mounting bracket. 6. Loosen the two lower ignition coil mounting bracket nuts. 7. Remove the two upper ignition coil mounting bracket bolts and discard. Subject: Loss of Power Steering Assist, Power Steering Warning Message Displayed in DIC, IPC/Radio Displays Erratic, DTC C0900, B1325 Set (Replace Ignition Coil/Module Assembly and Add Ground Strap) Models: 2004-2006 Chevrolet Malibu, Malibu Maxx with 3.5L Engine (VINs 8, N — RPOs LX9, LZ4) 8. Install the ground strap (1), P/N 12581176, to the upper left side of the bracket as shown between the coil bracket and intake. Install the new bracket bolt, P/N 11570082, (do not tighten at this time). Prior to installing the ground strap, remove the captured nut and washers. They are not needed (simply pound them out with a hammer on a vise). 9. Install the washer (2), P/N 02436162, to the upper right side of the bracket between the coil bracket and intake. Install the new bracket bolt, P/N 11570082, (do not tighten at this time). Tighten Tighten all the ignition coil bracket bolts and nuts to 25 N·m (15 lb ft). 10. Install the new ignition coil to the mounting bracket. 11. Install the other end of the ground strap to the coil as shown and secure using a new bolt, P/N 11588715. 12. Install the other three ignition coil bolts. Tighten Tighten the bolts to 10 N·m (89 lb in). 13. Connect the right side spark plug wires to the ignition coil. 14. Connect the left side spark plug wires to the ignition coil. 15. Connect the ignition coil electrical connector

Related Content:

diagram for ignition wires on a 1998 sebring 2 5l, replac upper valve cover gasket 2005 chevy malibu maxx 3 5, Owners Manual 2004 Chevy Malibu Maxx, malibu ml60t manual, how to replace a ignition coil on 2004 toyota sienna, repair of saab ignition coil, mazda speed 6 ignition module, firing order for a 2006 chevy malibn maxx, 1999 saturn replacement ignition switch bolts, 2006 pontiac torrent replacement ignition

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, Rav 4 steering rack dismantle and refit procedure, 99 buick park ave radiator installation, how to change power steering pump 2009 acada, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, 98 amigo isuzu how to remove power steering pump, youtube replace the hub on a meritor ff981 axle, schematic for 99 taurus power steering