Skip to content

how to connect door handle ford focus 2005

You search PDF repair manual about how to connect door handle ford focus 2005, if there are search results will appear below. If search results do not exist, please search by others keyword.

FORD, MERCURY, LINCOLN WHITE FLAKES COMING FROM A/ C VENTS SERVICE PROCEDURE

download
FORD: 2007-2009 MKX 2005-2009 Focus 2008-2010 Crown Victoria MERCURY: 2000-2005 Expedition, F-150 2008-2010 Grand Marquis, Mariner Hybrid, 2007-2009 Edge Mariner 2008-2010 Escape Hybrid, Escape LINCOLN: 2008-2010 Town Car SERVICE PROCEDURE MAY BE NECESSARY TO TEMPORARILY START THE ENGINE TO ENABLE MODE DOOR Hazard and Risk Warnings for White Flakes MOVEMENT. WARNING Clean A/C Ducts: MAY CAUSE EYE AND RESPIRATORY TRACT 1. Remove floor duct trim. IRRITATION. PROLONGED REPEATED EXPOSURE MAY CAUSE BONE DAMAGE 2. Using masking tape, connect one end of the (FLUOROSIS) AND HARM TO THE vacuum cleaner hose to the floor duct on driver RESPIRATORY SYSTEM (BASED ON ANIMAL side. DATA). • Avoid inhaling dust. 3. Tape closed all the other floor duct openings. • Avoid contact with eyes. 4. Obtain about two feet (61 cm) of rubber • Store away from acids. vacuum line large enough to fit the end of a small shop air blowgun. Secure the hose to the • Wash thoroughly after handling. end of the blowgun using a worm clamp. • Avoid release to the environment. 5. Close all instrument panel registers. NOTE THE USE OF DUST PROOF GOGGLES, 6. Set temperature setting to full cold. CHEMICAL RESISTANT GLOVES (PVC) AND 7. Place mode in floor / panel. DUST MASK IS RECOMMENDED. 8. Turn on vacuum cleaner

2002 Ford Focus L4-2.0L SOHC VIN P-Front Door Latch Removal And Installation Manual

download
Hood and Trunk Front Door Latch Service and Repair Front Door Latch Front Door Latch Notes REMOVAL 1. Remove the front door trim panel . 2. Remove the side impact energy absorption panel. 3. Remove the screw (if equipped). 4. Detach the door latch remote control. 1. Detach the handle from the door panel. 2. Detach the door latch remote control. 5. Peel back the watershield. CAUTION: Do not touch the adhesive surface as re-bonding will be impaired. 6. Disconnect the door latch actuator electrical connector. 7. Remove the exterior door handle access hole grommet from the door. 8. Loosen the screw. NOTE: The screw must be fully disengaged from the door lock cylinder bezel although it is not necessary to fully remove the screw 9. Remove the door lock cylinder bezel. 10. Remove the exterior door handle. 1. Slide the exterior door handle to release. 2. Remove the exterior door handle and gaskets. 11. Remove the screws. 12. Loosen the screw. NOTE: The screw must be fully disengaged from the exterior door handle although it is not necessary to fully remove the screw. 13. Detach the door latch. 1. Press the door latch to release. 2. Detach the door latch. 14. Detach the door latch security shield. 15. Remove the door latch and exterior door handle reinforcement plate. 16. Disconnect the door lock cylinder connecting rod. 1. Rotate the clip counterclockwise to release the connecting rod. 2. Disconnect the connecting rod. 17. Disconnect the exterior door handle reinforcement plate connecting rod.

Ford Focus power window removal And installation Instructions

download
Removing the Door Panel Coverings 1. For ease of installation, do both sides at the same time. 2. Roll the windows to approximately 1/2 open, and so the crank handle is in the Down Position. With either the Crank Spring Removal Tool, or a flat Screwdriver, remove the spring, located in a slot on the back of the crank. 3. Remove the cover plate for the remote-control mirror, which is held in place by 3 spring clips. Remove by gently pulling the front corner of the cover out, and then slide the cover back. 4. Remove the door Pull-handle cover, by inserting a screwdriver into the access hole on the bottom of the handle, and using the screwdriver as a lever, pop off the handle cover. 5. Remove the button covering a retaining screw in the interior door latch backing plate. 6. Remove the 8 Torx™ retaining screws around the perimeter of the door panel, and the single Torx™ retaining screw in the interior door latch. 7. Remove the 2 hex bolts in the door handle. 8. Gently lift the panel upwards, to disengage the window weather-strip molding. 9. Remove the Door Latch Trim Panel, be sure to unplug the Power Lock Switch, and remember how the wire was run. 10. Remove the interior door latch, by gently pulling out on the front corner, which is held in by a plastic compression spring. 11. Remove the Foam Arm Rest bolster, by unclipping the 4 plastic compression clips and the clip fasteners.. 12. Remove the 4 Door Speaker screws, and disconnect the speaker. 13. Gently remove the closed cell Foam Cover from the doorframe, by pulling out, while cutting the rubber cement around the cover. Remove all but the front edge of the cover. This cover tears very easily, so use extreme care. B. Removing the Manual Window Regulator 1. Temporarily re-attach the crank handle, and roll the window so that clamps (6, 7) on window are accessible through the voids in the door frame. 2. Loosen the glass clamp nuts (or bolts). 3. Roll the window all the way up, and lock in place by inserting a screwdriver into the small access hole at the top of the doorframe. 4. Remove the 4 Hex bolts (1, 2, 3) Before removing the last bolt (4), take up the weight of the glass, and remove the last bolt. Gently let the glass rest on the screwdriver. 5. Remove the manual regulator and tracks. C. Installing the Electric Window Regulator 1. Align and install the Hex bolts (1, 2, 3, 4, and nut 5) 2. Loosen the glass clamp nuts (or bolts). 3. Gently let the glass rest in the Clamps. 4. Lightly tighten the glass clamp nuts (or bolts).

1994 Ford Town Car/ Crown Victoria/ Grand Marquis Trim Panels, Door Removal And Installation Manual

download
Trim Panels, Door Front Town Car The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification. Removal CAUTION: To avoid breakage of door pull cover(s), insert a screwdriver diagonally between pull strap and chrome bracket. Snap out both sides then remove. 1. Snap out two door pull strap retaining screw covers. Remove screws. 2. Remove two screws on front and rear side of front door trim panel. 3. Using the Trim Pad Removing Tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent, pry the trim panel retaining clips from the door inner panel. NOTE: Do not use front door trim panel (23942) to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins. 4. Remove window regulator control switch housing from back of front door trim panel . Lift up housing, remove retaining screws and disconnect all connectors. 5. Disconnect driver seat regulator control processor switch (driver door only) if equipped. 6. Twist out interior lamp wire assembly and remove the front door trim panel. Installation 1. Ensure plastic watershield is secured to door panel. 2. Position front door trim panel to door. Connect interior lamp wiring. 3. Position the window regulator control switch housing and connect switch connectors. 4. Connect driver seat regulator control processor (14C708) (driver door only) if equipped. 5. Align door lock side to its mating slide on the sheet metal (front doors only) 6. Snap in front door trim panel . Ensure all retainers fit properly. 7. Install two retaining screws on front and rear side of front door trim panel . 8. Install two retaining screws and pull strap covers. Removal 1. Remove outside rear view mirror remote control unit. 2. Remove window regulator control switch housing by gently prying up, starting at the front. 3. Disconnect all connectors from window regulator control switch housing. 4. Remove inside door handle cup (22634) by gently prying at screwdriver slot with a screwdriver. 5. Remove push pin from front door trim panel upper front extension and remove screw. 6. Remove lower self-tapping screw retaining front door trim panel to door inner panel. 7. On Grand Marquis only, pry up screw covers from door pull handle and remove screws and handle. 8. Lift front door trim panel upward and snap out trim panel. 9. Disconnect wire harnesses from door panel as required and remove front door trim panel . Installation 1. Connect wire harnesses to front door trim panel as required. 2. Install front door trim panel by pushing in and down until it snaps into place. 3. Install all self-tapping screws retaining front door trim panel to door inner panel. 4. On Grand Marquis only, install door pull handle, tighten screws and install screw covers. 5. Install push pin covering screw on trim panel upper front extension. 6. Install inside door handle cup . 7. Install window regulator control switch housing.

2004 FORD F150 Door Window Glass-Rear SuperCrew REMOVAL AND INSTALLATION MANUAL

download
REMOVAL AND INSTALLATION 3. Remove the parts in the order indicated in the Door Window Glass — Rear, following illustration and table. SuperCrew To remove individual parts, only carry out the listed steps: NOTE: LH side is shown. RH side is similar. Part Steps 1. Remove the rear door trim panel. For additional Rear door window glass 1-4 information, refer to Section 501-00. Rear door window glass 1-7 regulator 2. Remove the rear door-mounted speaker. For additional information, refer to Section 415-00. Rear door window glass 1, 8 top run ItemPart NumberDescription ItemPart NumberDescription 4 1625712/ Rear door window glass 1 1625766/ Interior moulding (RH/LH) 1625713 (RH/LH) 1625767 Removal Note 2 1627458/ Watershield (RH/LH) 5 180103-14632 Window motor electrical 1627459 Removal Note connector Installation Note 6 W505421-S301Window regulator bolts (5 3 — Rear door window req’d) glass-to-regulator bolt (2 req’d) 7 1627000/ Window regulator assembly Removal Note 1627001 (RH/LH) (Continued) (Continued) Copyright © 2003, Ford Motor Company Last updated: 6/14/2004 2004 F150, 12/2003 501-00-2 501-00-2 Body System — Exterior REMOVAL AND INSTALLATION (Continued) Item 4: Rear Door Window Glass Removal ItemPart NumberDescription Note 8 1625766/ Rear door window glass top 1. Pull the glass out through the top inboard side 1625767 run (RH/LH) Removal Note of the door. 9 1625596/ Exterior moulding (right side) Item 8: Rear Door Window Glass Top Run 1625597 (RH/LH) Removal Note 4. To install, reverse the removal procedure. 1. Remove the glass top run through the top opening of rear door. Item 2: Watershield Removal Note Item 2: Watershield Installation Note 1. Do not tear or damage the watershield during disassembly. 1. Watershield must be installed so that edges have a weatherproof seal. Item 3: Rear Door Window Glass-to-Regulator Bolts Removal Note NOTE: Some vehicles may use rivets to attach the glass to the regulator. 1. If removing only the rear door glass regulator assembly and motor, secure the rear door glass in the full up position with tape.