how to fix the linkage for a 1998 ford explorer

You search PDF repair manual about how to fix the linkage for a 1998 ford explorer, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to fix the linkage for a 1998 ford explorer Direct Download speed 5432 Kb/s

  how to fix the linkage for a 1998 ford explorer Full Version speed 8172 Kb/s



1999 FORD EXPLORER/ RANGER TRANSMISSION-4R44E OR 5R55E-SLIPPING SHIFT/ DELAYED OR NO ENGAGEMENT REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 18-05-2012

download
SERVICE PROCEDURE F87Z-7A100-DB Main Control (4.0L EI Explorer) F87Z-7A100-EB Main Control (4.0L SOHC Explorer) 1. Perform normal diagnosis for this concern. XL2Z-7L491-AA Bracket XL2Z-7G383-AA Electronic Pressure Control (EPC) 2. Perform Line Pressure Tests as listed in the Solenoid 1999 Explorer/Mountaineer, Ranger Workshop Manual. OTHER APPLICABLE ARTICLES: NONE WARRANTY STATUS: Eligible Under The 3. If pressures are low, perform Pinpoint Test for Provisions Of Bumper To the EPC solenoid. Bumper Warranty Coverage And Emissions Warranty 4. Inspect the bracket that attaches the Torque Coverage Converter Clutch (TCC), Shift Solenoid B OPERATION DESCRIPTION TIME (SSB), Shift Solenoid D/Coast Clutch Solenoid 991610A Replace Electronic 1.2 Hrs. (SSD/CCS), and EPC solenoids to the main Pressure Control (EPC) control for damage. If the bracket is damaged, Solenoid And Clean Main replace both the bracket and solenoid. Control (Includes Time For 5. If the bracket is not damaged, inspect the Road Test) – 4R44E Or solenoid for the affected date code (refer to the 5R55E following Manufacturing Date Code Chart) and 991610B For Line Pressure And ID marking (Figure 1, Views 1, 2, and 3). If the Pinpoint Tests, Use “A” solenoid is one of the affected, replace it. Time As Outlined In The Warranty And Policy MANUFACTURING DATE CODE Manual Date Code Month/Year DEALER CODING 868xx August 1998 CONDITION 869xx September 1998 BASIC PART NO. CODE 870xx October 1998 7G383 01 871xx November 1998 OASIS CODES: 501000, 502000, 50300

Related Content:

replacing manual, remove r lower control arm 1998 olds 88 what electric impack wrench to usee, vw po1544, how replace torque converter clutch solenoid on a 1998 suburban, escort transmission harsh engagement, replace ford explore sports 1999 clutch line, 5r55e tcc, how to remove a epc solenoid from a1998 ford expedition transmission, isuzu trooper fuel solenoid valve location, pictures removing the epc solenoid on a1998 f150

2008 Ford Explorer/ Mountaineer/ Explorer Sport Trac Headliner REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 04-05-2012

download
Explorer and Mountaineer only 1. If equipped, remove the rear entertainment system. For additional information, refer to Section 415-00 . Explorer Sport Trac only 2. NOTE: The headliner is removed through the rear passenger door. To facilitate removal, the front passenger seat must be removed. Remove the front passenger seat. For additional information, refer to Section 501-10 . All vehicles 3. Remove the overhead console. For additional information, refer to Section 501-12 . 4. Remove the A-pillar trim panel. For additional information, refer to A-Pillar Trim Panel in this section. 5. Position the B-pillar upper trim panel aside. For additional information, refer to B-Pillar Upper Trim Panel in this section. Explorer and Mountaineer only 6. Remove the C-pillar trim panel. For additional information, refer to C-Pillar Trim Panel — Explorer, Mountaineer in this section. 7. Remove the D-pillar trim panel. For additional information, refer to D-Pillar Trim Panel in this section. Explorer Sport Trac 8. Position the C-pillar upper trim panel aside. For additional information, refer to C-Pillar Upper Trim Panel — Explorer Sport Trac in this section. All vehicles 9. Remove the gimp around the roof opening panel, if equipped. 10. Remove the 4 sun visor retainer screws. 11. Remove the sun visors. 12. Carefully lower the headliner at the corner of the sun visor location to access the electrical connector and disconnect the electrical connector. 13. Disconnect the roof opening panel, if equipped. 14. Disconnect the interior mirror electrical connector and electronic compass sensor connector, if equipped. 15. Use a thin-blade tool and carefully remove the dome lamp cover. 16. Disconnect the dome lamp electrical connectors. Explorer and Mountaineer only 17. Remove the upper air duct. * Remove the pin-type retainers. * Push down on the duct, tilt the top outward and pull upward to remove. 18. Remove the lower air duct. 19. Disconnect the electrical connector located at the C-pillar. * Release the wiring harness pin-type retainers. 20. Disconnect all the electrical connectors. All vehicles 21. Disconnect the electrical connector and the wiring pin-type retainers on the A-pillar. 22. CAUTION: To prevent bending or damaging the headliner, an assistant is required to support the headliner while carrying out the remaining steps. Open the sun visor center retainer cover and remove the screw. 23. Remove the sun visor center retainer. 24. Remove the rear pin-type retainer. 25. CAUTION: To prevent damaging the garment hanger retainer, use a 3/16-inch flat-blade screwdriver to carry out this step. NOTE: The garment hanger is shown without the roof sheet metal screw to show the metal retainer clip. The metal retainer clip will remain engaged in the sheet metal after the garment hanger is removed. Remove the garment hangers. 1. Open the access door. 2. Insert the flat-blade screwdriver fully into the garment hanger slot. 3. Rotate the screwdriver 90 degrees so that the screwdriver spreads the metal retainer clip. Remove the plastic garment hanger. 26. NOTE: The headliner is removed through the passenger rear door for Explorer Sport Trac. Remove the headliner. 27. To install, reverse the removal procedure.

Related Content:

yhow to remove and install airbag for fored explorer sport trac, 2001 Sport Trac Manual Download, location of the GEM module 02 explorer, lube points on a 1997 thunderbird, overhead console sport trac fix, rear window wont go up connector in sill plate 05 ram, remove rear pillar camry, repair manual for 1999 Ford Explorer Sport, sport trac 2004 passenger air bag removal cover, Sun Battery Tester manual

HIGH TECH DUAL QUAD THROTTLE LINKAGE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (More Manuals) by admin on 02-01-2012

download
INSTALLATION 1. This kit contains all the necessary parts to operate Edelbrock carburetors in a progressive or 1: 1 type operation. Figure 1 illustrates typical progressive type installation in which the rear carburetor is the primary carb. This simplifies linkage attachment to the vehicle’s existing throttle linkage. 2. Before attaching anything to the carburetors, loosely assemble the major components of the linkage kit using Figure 1 as a guideline. Note that the longer rod will go to the rear carb with the flat facing down, and the short rod goes to the front carb with the flat facing up. The brass bearing blocks should be positioned so that the set screws will tighten against the flat of the short rod, i.e., both bearing block set screws will be up. Attach the aluminum collar to the long rod between the bearing blocks with the set screw against the flat. 3. Attach the linkage assembly to the carbs with the 10-24 allen head screws and locknuts. Attach to the rear carb using one of the brass 518″ O.D. x 3/16″ I.D. shoulder spacers and the tapered brass anti-rotation shoulder spacer in the top hole of the throttle arm (112″ diameter). Note that the shoulder spacer goes on the inside and the anti-rotation spacer goes on the outside of the throttle arm. Attach to the front carb using the 3/16″ hole just below the large hole in the throttle arm. ADJUSTMENT – NOTE: If carburetors are full of fuel, place rags in the carb throats to absorb the fuel discharged when working the throttle linkage. This will prevent flooding and possible damage to the piston rings upon start-up. Be sure to remove the rags before starting engine. 1. Tighten the set screw and locknut on the rear bearing block, making sure that the bearing block is close to the end of the shaft from the front carburetor. 2. Push the throttle arms of both carbs to WOT (Wide Open Throttle), then adjust the aluminum collar to touch the rear brass bearing block. Securely tighten the set screw and locknut on the aluminum collar. 3. Let both throttle arms return to idle position, then adjust the front brass bearing block to almost touch the aluminum collar. Leave about .020″-.030″ clearance to allow for independent idle speed adjustment of each carburetor. Tighten all set screws, locknuts, and bolts at this time. 4. Check for smooth operation of linkage from idle to WOT and note that the rear carb will open about 20″ before starting to open the front carb. Both carbs should reach WOT at the same time. 5. IMPORTANT: Attach a return spring to both carburetors as shown in Figure 1. Use the return spring brackets supplied, bending as necessary for attachment to your engine. Generally the brackets can be attached to the intake manifold using the existing bolts. Use the longer or shorter spring on either the front or rear carburetor as required for your particular application. Check for smooth operation and positive return to idle. 6. Attach existing throttle linkage to rear carburetor using the 3/16″ hole below the large hole in the throttle arm. It may be necessary to shorten your existing linkage rod or cable, or to use an aftermarket cable mounting plate. BEFORE STARTING ENGINE, DOUBLE-CHECK FOR SMOOTH OPERATION OF LINKAGE FROM IDLE TO WIDE OPEN THROTTLE AND FOR POSITIVE RETURN TO IDLE. OPTIONAL 1:l INSTALLATION If 1:l linkage is desired, assemble and attach linkage kit as above, except that the attachment point to the front carburetor’s throttle arm will be the large 112″ hole using the other two 518″ O.D. x 3/16″ I.D. shoulder spacers (similar to the rear carburetor). Adjust the bearing blocks to eliminate all freeplay, so that all motion to the rear carburetor’s throttle arm is transmitted directly to the front carb’s throttle arm

Related Content:

iS THERE A SPRING CONNECTING THE LINKAGE TO THE TPS ON A97 LESABRE, edelbrock dubble carburetor adjustment linkage, relearn on throttle body trailblazer 2005, throttle body for a 2006 buick rendezvous, relearn procedure for throttle body 2004 chevy trailblazer, volvo penta throttle control diagram, p1512 chevy trailblazer, where is the fuel line to throttle body on a 2006 KIA RIO, lincoln ls throttle linkage, jaguar s type throttle body return spring

HIGH TECH DUAL QUAD THROTTLE LINKAGE KIT INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 24-02-2012

download
INSTALLATION 1. This kit contains all the necessary parts to operate Edelbrock carburetors in a progressive or 1: 1 type operation. Figure 1 illustrates typical progressive type installation in which the rear carburetor is the primary carb. This simplifies linkage attachment to the vehicle’s existing throttle linkage. 2. Before attaching anything to the carburetors, loosely assemble the major components of the linkage kit using Figure 1 as a guideline. Note that the longer rod will go to the rear carb with the flat facing down, and the short rod goes to the front carb with the flat facing up. The brass bearing blocks should be positioned so that the set screws will tighten against the flat of the short rod, i.e., both bearing block set screws will be up. Attach the aluminum collar to the long rod between the bearing blocks with the set screw against the flat. 3. Attach the linkage assembly to the carbs with the 10-24 allen head screws and locknuts. Attach to the rear carb using one of the brass 518″ O.D. x 3/16″ I.D. shoulder spacers and the tapered brass anti-rotation shoulder spacer in the top hole of the throttle arm (112″ diameter). Note that the shoulder spacer goes on the inside and the anti-rotation spacer goes on the outside of the throttle arm. Attach to the front carb using the 3/16″ hole just below the large hole in the throttle arm. ADJUSTMENT – NOTE: If carburetors are full of fuel, place rags in the carb throats to absorb the fuel discharged when working the throttle linkage. This will prevent flooding and possible damage to the piston rings upon start-up. Be sure to remove the rags before starting engine. 1. Tighten the set screw and locknut on the rear bearing block, making sure that the bearing block is close to the end of the shaft from the front carburetor. 2. Push the throttle arms of both carbs to WOT (Wide Open Throttle), then adjust the aluminum collar to touch the rear brass bearing block. Securely tighten the set screw and locknut on the aluminum collar. 3. Let both throttle arms return to idle position, then adjust the front brass bearing block to almost touch the aluminum collar. Leave about .020″-.030″ clearance to allow for independent idle speed adjustment of each carburetor. Tighten all set screws, locknuts, and bolts at this time. 4. Check for smooth operation of linkage from idle to WOT and note that the rear carb will open about 20″ before starting to open the front carb. Both carbs should reach WOT at the same time. 5. IMPORTANT: Attach a return spring to both carburetors as shown in Figure 1. Use the return spring brackets supplied, bending as necessary for attachment to your engine. Generally the brackets can be attached to the intake manifold using the existing bolts. Use the longer or shorter spring on either the front or rear carburetor as required for your particular application. Check for smooth operation and positive return to idle. 6. Attach existing throttle linkage to rear carburetor using the 3/16″ hole below the large hole in the throttle arm. It may be necessary to shorten your existing linkage rod or cable, or to use an aftermarket cable mounting plate. BEFORE STARTING ENGINE, DOUBLE-CHECK FOR SMOOTH OPERATION OF LINKAGE FROM IDLE TO WIDE OPEN THROTTLE AND FOR POSITIVE RETURN TO IDLE. OPTIONAL 1:l INSTALLATION If 1:l linkage is desired, assemble and attach linkage kit as above, except that the attachment point to the front carburetor’s throttle arm will be the large 112″ hole using the other two 518″ O.D. x 3/16″ I.D. shoulder spacers (similar to the rear carburetor). Adjust the bearing blocks to eliminate all freeplay, so that all motion to the rear carburetor’s throttle arm is transmitted directly to the front carb’s throttle arm

Related Content:

4g13 engine ignition adjustments, carburetor kancil 850, carter duel quad carb adjustment, Duromax 7 hp idle adjustment, how to change kancil carburetor, schematic diagram of elect fuel system include locations for a 1989 toyota camry 2 0 engine passenger car, setting caburater kancil, specialist kancil carburetor, volvo penta 3 0 glpj valve adjustment

1998-2000 ISUZU RODEO/AMIGO HIGH/ERRATIC IDLE CONDITION SERVICE MANUAL

0

Filed Under (Isuzu Manuals) by admin on 13-05-2012

download
1998 – 2000 MODELS 1. Inspect main ground points (refer to SB99*04*S001 for more information). * P6 ground point-body [on the passenger side of engine compartment, between the battery and cruise control actuator (if equipped)]. (Figure Fig. 1 ) * P10 ground point-engine (at the alternator bracket) . (Figure Fig. 2 ) Isuzu: 1998 – 2000 Rodeo AFFECTED VEHICLES:1998 – 2000 Rodeo (UE)/Amigo (UA) models with 3.2L V6 engines NOTE: Please refer to the appropriate workshop manual for the correct diagnosing procedure and/or follow the service procedures outlined in this bulletin for the vehicle being serviced. NOTE: The 1998, 1999 or 2000 Rodeo/Amigo Electrical Troubleshooting Manual can assist in locating the vehicle ground distribution (i.e., ground contact points). * Perform a voltage drop test at the main ground points. * If the voltage drop test fails, then inspect and clean both the bolt and contact point. * Verify and correct idle settings (if needed) as described in the workshop manual. * If the repair procedure on this step solves the high idle condition, then return the vehicle to the customer. If the repair procedure on this step does not solve the high idle condition, then go to step 2 (16 pin Blue Connector). B. Remove P-6/P-10 ground terminal and bolt for ground contact inspection. * Inspect ground contact area for corrosion. * Inspect bolt and thread for damage or corrosion. * Clean the ground area and fastening bolt thoroughly with a wire brush. * Replace bolt if damaged or heavily corroded. C. Install the P-6/P-10 ground terminal and bolt (tighten using hand tools only). * Torque the P-6/P-10 ground terminal bolt to (14 N.m) 10 lb.ft. 1998 – 1999 MODELS ONLY 2. Inspect the 16 pin blue connector, located under the power steering fluid reservoir for corrosion, bent, or damaged pins (specifically for the Throttle Position Sensor). (Figure Fig. 3 )

Related Content:

disassemble engines xj8 jaguar, 1998 Chrysler Concorde Manual free, isuzu trooper grounding strap, 2000 Isuzu Rodeo Repair, 1998 jaguar fuse location, grounding points on 99 windstar, unable to tighten side post battery cable on 1998 chevy z71, volvo s70 t5 wiring pdf, ford expedition torque converter, downloadable iszuzu rodeo 1997 owners manual

2003 Ford Truck Expedition Suspension – Air Suspension Height Sensor Linkage Loose Service Procedure

0

Filed Under (Ford Manuals) by admin on 10-01-2012

download
ISSUE Some 2003-2006 Expedition and Navigator vehicles equipped with an air suspension may exhibit an air suspension height sensor linkage arm disengaging from the suspension ball stud or height sensor rotating arm. This concern typically occurs with the rear sensor (Figure 1) but may occur with the front sensors as well. If this occurs, the symptom will typically be the vehicle leaning to one side, the vehicle sitting too low/high, a harsh ride, and/or an inoperative air suspension. In addition, this concern may result in diagnostic trouble code (DTC) C1725 (air suspension front pneumatic failure) or C1726 (air suspension rear pneumatic failure). ACTION When a linkage arm becomes disengaged, do not re-attach the arm and do not replace the sensor unless broken. Instead, install a revised linkage arm on all three (3) sensor assemblies, even if they have not detached from the ball stud. 1. Replace linkage arms on all three (3) sensor assemblies following Workshop Manual (WSM), Section 204-05. 2. Discard the old linkage arms. NOTE IF THE SENSOR ASSEMBLY NEEDS TO BE REPLACED FOR ANY DAMAGE/FAILURE OTHER THAN THE ONE DESCRIBED IN THIS TSB, THE REPLACEMENT ASSEMBLY IS SUPPLIED WITH A NEW STYLE LINKAGE ARM, SO THERE IS NO NEED TO ORDER ADDITIONAL LINKAGES FOR THE SERVICE REPAIR. WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage OPERATION DESCRIPTION TIME 061510A 2003-2006 0.4 Hr. Expedition/Navigator: Replace The Three Linkage Arms, Includes Time To Check Diagnostic Trouble Codes (Do Not Use With 5300A, 5300A7, 5300A8) DEALER CODING CONDITION BASIC PART NO. CODE 5A967

Related Content:

2003 ford explorer front endSUSPENSION ASSEMBLY chematics, 2006 f150 front suspension diagram, air suspension sensor ford, change front struts 2006 gs300, how to repair 03 explorer front control arm, schematic for 2003 lincoln town suspension

2006 Ford Pickup F350 Super Duty Intake Manifold Component Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 13-05-2011

download
Removal All vehicles 1. Remove the auxiliary battery. For additional information, refer to BATTERY, MOUNTING AND CABLES . 2. Remove the cooling fan stator. For additional information, refer to ENGINE COOLING . 3. Remove the degas bottle. For additional information, refer to ENGINE COOLING . 4. Disconnect the upper radiator hose. Fig. 23: Locating Upper Radiator Hose Courtesy of FORD MOTOR CO. Fig. 24: Locating Turbocharger-To-CAC Duct Courtesy of FORD MOTOR CO. 5. Remove the turbocharger-to-CAC duct Vehicles with dual generators 6. Remove the accessory drive belt. Fig. 25: Rotating Drive Belt Tensioner Clockwise Courtesy of FORD MOTOR CO. 7. Remove the bolt and the accessory drive belt tensioner. Fig. 26: Locating Accessory Drive Belt Tensioner Bolt Courtesy of FORD MOTOR CO. 8. Remove the accessory drive belt. Fig. 27: Rotating Accessory Drive Belt Tensioner Courtesy of FORD MOTOR CO. 9. Remove the bolts, bracket and accessory drive belt idler pulley. Fig. 28: Locating Bracket And Accessory Drive Belt Idler Pulley Bolts Courtesy of FORD MOTOR CO. 10. Remove the bolts and the accessory drive belt tensioner. Fig. 29: Locating Accessory Drive Belt Tensioner Bolts Courtesy of FORD MOTOR CO. 11. Disconnect the wiring harness retainer, generator electrical connector and B+ wire. Fig. 30: Locating Wire Retainer And Generator Electrical Connectors Courtesy of FORD MOTOR CO. 12. Remove the bolts and the generator with mounting bracket.

Related Content:

555 ford backhoe repair manual, ford 9 inch repair manual, How to Fix Po446 Code ford escape xls, Ford E 450 Cutaway Manual, 2006 ford f150 pdf manual, 2006 ford escape lock solenoid location, 1988 ford f150 302 where is Diagostic Link Connector located, where is the vct solenoid located on a 2009 ford escape, how many quarts of transmission fluid does 2012 ford e450 take?, windstar dtc u1131

Vehicles Equipped with a Webasto Sunroof System

0

Filed Under (More Manuals) by admin on 13-02-2011

download
Models: 1997-2000 Buick Century 1988-1991 Buick Reatta 1988-1999 Buick Riviera 1989-2000 Buick Park Avenue 1998-2000 Buick Regal 1988-1997 Cadillac Seville 1988-1996 Cadillac Fleetwood 1988-2000 Cadillac Eldorado 1989-2000 Cadillac DeVille 1995-2000 Chevrolet Cavalier 1998-2000 Chevrolet Malibu 2000 Chevrolet Impala, Monte Carlo 1988-1995 Oldsmobile Ciera 1989-1996 Oldsmobile Ninety Eight 1994-1998 Oldsmobile Achieva 1995-1999 Oldsmobile Aurora 1997 Oldsmobile Silhouette 1998-1999 Oldsmobile Cutlass 1998-2000 Oldsmobile Intrigue 1999-2000 Oldsmobile Alero 1987 Pontiac 6000 1989-1998 Pontiac Bonneville 1994-2000 Pontiac Grand Am 1995-2000 Pontiac Sunfire 1997-1998 Pontiac Trans Sport 1997-2000 Pontiac Grand Prix 1997-2000 Chevrolet & GMC S/T Models (Blazer, Jimmy) 1997-2000 Oldsmobile Bravada #99-08-67-003: Info – Vehicles Equipped with a Webasto Sunroof System – (Jul 23, 1999) This bulletin is being revised to update the model information. Please discard Corporate Bulletin Number 43-10-18A (Body Section)

Related Content:

location of evap purge valve valve on 99 2 2 s10, 200 buick lesabre computer diagram, 2000 buick century service manual free, 2000 saturn sl1 owners manual, 560sl repair 1988, 2000 coleman tacoma owners manual, is it hard to replace the ac compressor on a 2001 mercury cougar 2 5l 12valve car, 2000 chevrolet suburban haynes, 2000 Chevy Impala Passkey Bypass is there a fuse, 2000 coleman utah manual

K40016 ADD-A-LEAF SPRING KIT INSTALLATION INSTRUCTIONS

0

Filed Under (More Manuals) by admin on 19-04-2012

download
CHEVY 1982-98 S Series all 2WD/4WD 1972-82 LUV PU 2 WD DODGE 1994-99 Ram 1500 2WD 1994-00 Ram 1500 4WD FORD 1990-96 F 150 std or ext cab 2WD 1982-89 F 150 std or ext cab 2WD 1983-1996 Ford Bronco II 4WD 1983-1996 Ford Bronco II 2WD 1983-1997 Ford Ranger 2WD/4WD 1990-00 Ford Ranger 2WD 1983-97 Ford Explorer 2WD/4WD 1972-84 Ford Courier 2WD K40016 ADD-A-LEAF SPRING KIT JEEP 1984-01 Jeep Cherokee 1974-86 CJ-5/CJ-7/CJ-8 4WD 1967-73 Jeepster/C101/C101 w multileaf Jeep Wrangler 1987-96 Front and Rear LAND ROVER 1959-1981 All 4wd MITSUBISHI 1986-91 Montero 1982-84 PU 2WD/4WD NISSAN 1968-1997 PU/Pathfinder 2WD/4WD TOYOTA 1963-98 Toyota PU/4 Runner with 2.5″ rear springs The K40016 Add-A-Leaf Spring Kit retrofits onto the following vehicles: The kit consists of two each 28″ Leaf Springs and two sets of two each longer bolts and nuts of different diameters. The same diameter bolt currently on the vehicle should be used and the other set discarded. • PLEASE READ ALL INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE INSTALLATION • You must use 2-large “C-clamps” or a large vise to contain the elastic potential energy stored in a leaf spring when the center bolt is removed. • The new leaf spring will be placed in the existing spring assembly in a progressive pyramid shape. Example – if your number 1 Spring is 32″ long and the next one is 25″ long, the new Add-A-Leaf Spring should be place between them. • Some vehicles will have a flat helper stack. SEE ILLUSTRATION – DO NOT INSTALL THE NEW ADD-A-LEAF SPRING IN OR BELOW THE HELPER SPRIN(S). Helper spring assembly. Do not install Add-A-Leaf in or below this assembly Lowest allowable position for Add-A-Leaf

Related Content:

1969 ford truck ranger 390 overheating did not start till change water pump, fluid spec for 2004 ford ranger, f53 96 manual, 83 ranger wiring diagram, 1996 Ford RV specifications, 1996 Ford Explorer Repair Manual, 1996 ford explorer manual, 1996 f53 manifold exhaust repair, 1986 555b ford backhoe injector pump, ford ranger 2 3 engine diagram

1999 Chevrolet Silverado The service engine soon light is on with trouble code P1416 present

0

Filed Under (Chevrolet Manuals) by admin on 07-05-2012

download
Tests/Procedures: 1. Use a scanner and command the air pump on with the engine running at idle. Check if the O2 sensors go lean. 2. If the O2 sensor does not go lean on one bank, see if the check valve at the exhaust manifold is stuck closed, not allowing air into the manifold. Potential Causes: Defective Check Valve Diagnostic Codes: P1416 Author: Christopher Pittman Average Reported Mileage: 85812 Confirmed Fix Summary Confirmed Fix 18 – Air Injection Reaction (AIR) Check Valve 1 – Air Injection Reaction (AIR) Check Valve, Air Injection Reaction (AIR) Pump Confirmed Fix Details Tech Reported Fix Details Confirmed Fix Lee Stroup Sr. November 15, 2007 2001 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * A.I.R. Check Valve – removed check valves, found one rusted closed, one restricted, replaced both valves. Moisture from exhaust seems to have rusted both valves. Air Injection Reaction (AIR) Check Valve Paul Puleo August 20, 2009 1999 Chevrolet Camaro, Z28 5.7L * Replaced Both Air Injection Reaction (AIR) Check Valves – bank 2 AIR check valve restrticted, bank 1 slightly restricted replaced both Air Injection Reaction (AIR) Check Valve SouthGate January 05, 2009 2000 Chevrolet Silverado 1500, 4.8L, Vin V, Eng Cfg V8 * Replaced Air Injection Reaction (AIR) Check Valve – replaced boht check valves. fix the code. Air Injection Reaction (AIR) Check Valve Dwight Heckman July 31, 2008 2000 Chevrolet Blazer, 4.3L * Check Valve – replacing the check valve and cleaning out the lines repaired the problem. Air Injection Reaction (AIR) Check Valve Nick Secchitano June 16, 2009 2000 Chevrolet Silverado 1500, 5.3L, Vin T, Eng Cfg V8 * Replaced Both Air Injection Reaction (AIR) Check Valves – Air injection check valves Air Injection Reaction (AIR) Check Valve Mark Bertelsen 1998 Chevrolet Camaro, Z28 5.7L * Replaced Air Injection Reaction (AIR) Check

Related Content:

acura mdx check charging system, how to drain the air conditioner on a 2003 jetta, where do you recharge ac on 1996 buick regal, 2007 chevy trailblazer code c0161, troubleshooting P069E, tranny fluid location 2010 santa fe, 4M51Engine valve clearance, free PDF repair manuals 1999 chevy silverado, reset procedure for ride heighth 04 navigator, chevy impala air conditioner flapper doesnt turn off

Related Content:

replacing manual, remove r lower control arm 1998 olds 88 what electric impack wrench to usee, vw po1544, how replace torque converter clutch solenoid on a 1998 suburban, escort transmission harsh engagement, replace ford explore sports 1999 clutch line, 5r55e tcc, how to remove a epc solenoid from a1998 ford expedition transmission, isuzu trooper fuel solenoid valve location, pictures removing the epc solenoid on a1998 f150