how to install fog light on 2013 camry le

You search PDF repair manual about how to install fog light on 2013 camry le, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to install fog light on 2013 camry le Direct Download speed 5432 Kb/s

  how to install fog light on 2013 camry le Full Version speed 8172 Kb/s



1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

0

Filed Under (Chevy Manuals) by admin on 14-05-2012

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, how to remove 2011 dodge durango grill, 2008 yaris hatchback remove headliner replace antenna, Redezvous Dash Removal, 2005 buick lesabre instrument cluster removal, remove 2010 highlander radio, remove fender 2001 grand prix, 2006 frontier remove window switch panel, remove front dash on 2014 optima

TOYOTA PRIUS FOG LIGHT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 18-03-2012

download
Remove the negative battery terminal Installation 1. Secure the relay to the next to the fuse block with wire ties 2. Attach the ring terminal with 2 black wires to ground 3. Attach fog light 12v red wire to open spade inside the fuse block as shown in picture 1 Picture 1 4. Locate the large vehicle harness grommet on the left side. Cut the auxiliary wiring access nipple off the grommet and push small 2-wire connector through firewall. Note: Extra caution should be taken not to damage connector 5. Run wires along the driver side of the engine compartment. Secure with wire ties as needed 6. From inside the cabin remove dash panels and locate the little small connector that was pushed through in step 4. Plug it to the switch harness. 7. T-tap orange/black wire from fog light harness to connector 2C pin 32 green wire. Pin 32 is on the left side of the connector 7th pin up from bottom of the connector. Connector 2C located left of the steering column above big white wire picture 2 Picture 2 8. T-Tap green/black wire from fog light harness to connector L47 pin 11, pink wire (it is the last pin to the left). Connector L47 is on the steering column and plugs into the headlight control arm picture 3 Picture 3 9. Mount switch into switch knockout of dash (picture 4) FOG LIGHT KIT INSTALLATION INSTRUCTIONS TPR-301 TOYOTA PRIUS 2010+ Picture 4 10. Install switch harness 11. Reinstall dash panels 12. Route the fog light wire under car. 13. Remove fog light cover plates and lower splash shields 14. Mount fog lights into bezel by sliding fog light tabs into slots and secure other side with supplied screw (see picture 5) Picture 5 15. Install both fog light bezels 16. Plug in left side fog light into harness plug 17. Run right fog light wire harness and plug into right fog light. Secure with wire ties 18. Reattach the lower splash shields

Related Content:

installing fog lights in 2012 sienna, how to connect fj cruiser corner fog lights, how to replace fog light on 2010 corolla youtube, 2010 corolla fog lamp installation, install instructions for fog lights on 2014 tacoma, install fog light 2013 sienna, install camry 2004 fog lights, how to replace fog light on 2010 corolla, how to install replacement fog lights in toyota rav 4 2014, how to install fog lights on a 2007 camry

200-92010 Toyota Camry/ Corolla OE Fit Fog Light Install Instruction

0

Filed Under (Toyota Manuals) by admin on 28-04-2012

download
Installation 1. Secure the Relay to the wire loom next to the Battery with wire ties. Secure top and bottom with wire ties. 2. Attach the ring terminal with 2 black wires to the 10mm bolt next to the relay 3. Connect the ring terminal from the relay (12v red wire) to the positive terminal of the battery 4. Locate the large vehicle harness grommet on the left side. Cut the auxiliary wiring access nipple off the grommet and push small 2-wire connector through firewall. Note: Extra caution should be taken not to damage connector. Seal with 3M Silicone sealant (see picture 1) Picture 1 5. Run the fog light wire harness on the driver side of the car. Use wire ties as needed. 6. Remove dash panels 7. Mount switch into switch knockout on left side of dash 8. From inside the cabin, locate the small connector that were pushed through in step 4. It will be the grommet above the gas pedal 9. Install switch harness 10. T-tap green/black wire from fog light harness to connector E21 pin 11, light green wire (first pin on right). Connector E21 is located on the left side of the steering column (picture 2) Picture 2 11. T-Tap orange/black wire from fog light harness to connector ID pin 3, pink wire (middle third pin from left). Connector ID is left of steering wheel (picture 3) Picture 3 12. Secure with wire ties. 13. Reinstall dash panels 14. Route the fog light wire under car. 15. Remove fog light cover plates and lower splash shields on both sides 16. Insert one side of the fog light into the plastic sleeve and secure other side with supplied Phillip screws (see picture 4

2007-2011 Toyota Tundra Fog Light Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 14-03-2012

download
Installation 1. Secure the Relay to the wire loom next to the Battery with wire ties. Secure top and bottom with wire ties (see Picture 1). Note: It is suggested to loosen the battery from the base and move it to allow extra working room. Picture 1 2. Attach the ring terminal with 2 black wires to the 10mm ground bolt next to the battery (see picture 2) Run the fog light wire harness on the driver side of the car. Use wire ties as needed Vehicle Disassembly 5. Remove the screws on the lower part of the instrument panel (picture 6) Picture 6 6. Remove lower instrument panel sub assy (picture 6) 7. Mount switch into switch knockout on left side of dash (see picture 9) Picture 9 8. From inside the cabin, locate the wires that were pushed through in step 4. It will be the grommet above the gas pedal (see picture 10) Picture 10 9. Install switch harness (see picture 11) Picture 11 10. Locate the junction box behind the lower instrument panel (picture 12) Picture 12 11. T-tap green/black wire from fog light harness to connector DB pin 16, red wire (bottom pin on right). Connector DB is in the driver’s side junction box, located on the left side of the steering column (pic. 13 & 14) 12. T-Tap orange/black wire from fog light harness to connector DB pin 18, blue wire (right side third pin up from bottom). Connector DB is left of steering wheel (picture 13 and 14) Picture 13: Close up of junction box, viewed from driver’s seat Picture 14A Picture 14B Picture 14A: Diagram of junction box, driver’s seat view Picture 14B: DB connector (showing Pin 16 and 18) 13. Secure with wire ties. 14. Reinstall dash panels 15. Route the fog light wire under car. 16. Remove splash shields 17. Remove both front bumper hole covers. Detach wire harness clamps and release the 3 claws and remove (picture 15) Picture 15 18. Re-secure detached wire harness and plug in left side fog light into harness plug and secure with wire ties. Snap fog light bezel into bumper hole (picture 16) Picture 16 19. Run right side of wire harness through bumper sub frame to right fog lamp opening (see picture 17

Related Content:

how to change steering belt toyota echo 2003, 94 tbird fuses, 08 silverado taillights wiring harness installation, h3 wiring harness causing turn signal problem, jaguar etype hanbrake wire, kia data link connector, kia sorento 2007 drivers seat electrical connection, kia sorento 2007 drivers seat electrical plug wiring, location of horn relay on toyota tundra 2011 model, motor controllert for a 2007 ruff-n-tuff

2009 Toyota Corolla AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 07-07-2012

download
INSTALLATION 1. INSTALL FRONT AXLE HUB BEARING 2. INSTALL FRONT DISC BRAKE DUST COVER (a) Install the disc brake dust cover to the steering knuckle with the 3 bolts. Torque: 8.3 N·m (85 kgf·cm, 73 in·lbf) 3. INSTALL FRONT AXLE HUB SUB-ASSEMBLY 4. INSTALL FRONT AXLE HUB HOLE SNAP RING Last Modified: 4-24-2008 5.1 A From: 200712 Model Year: 2009 Model: Corolla Doc ID: RM000001IWX00ZX Title: AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION (2009 Corolla) (a) Using SST and a press, install a new front axle hub bearing to the steering knuckle. SST: 09950-60020 09951-00720 SST: 09950-70010 09951-07100 (a) Using SST and a press, install the front axle hub sub-assembly. SST: 09608-32010 SST: 09950-60010 09951-00600 SST: 09950-70010 09951-07100 5. INSTALL FRONT LOWER BALL JOINT 6. INSTALL FRONT AXLE ASSEMBLY 7. INSTALL FRONT LOWER SUSPENSION ARM 8. INSTALL TIE ROD END SUB-ASSEMBLY 9. INSTALL FRONT DISC 10. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY 11. TEMPORARILY INSTALL FRONT AXLE HUB NUT (a) Using snap ring pliers, install a new front axle hub hole snap ring. (a) Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly. (b) Install the front axle assembly to the front shock absorber with the 2 bolts and the 2 nuts. Torque: 240 N·m (2448 kgf·cm, 176 ft·lbf) Be careful not to damage the drive shaft boot or speed sensor rotor. Page 2of 4

Related Content:

calipers torque toyota corolla 2009, 2008 avalanche dtc code u0109, 2006 corolla front wheel hub assembly schematics, 2009 gm u0109, Repair manual hyundai accent 1 5 camshaft installation model 96, replace 2000 toyora corolla caliber bolts

42R Turbo kit Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 19-03-2012

download
1. Open all boxes and inspect parts and verify from packing list that everything is there. 2. Find Turbo, Header, T4 Gasket, and Waste gates. 3. Carefully remove turbine housing from turbo. 4. Install 10×1.25 stud in location as indicated by picture. 5. Install Gasket and use nuts and bolts with lock washers to secure turbine housing to header.(use anti-seize on threads) 6. Carefully install the rest of the turbo to the turbine housing. Leave the clamps a little loose. (enough to rotate assemblies) 7. Use supplied TiAL gaskets and install waste gates to header. (use anti-seize to lube threads) 8. Install oil feed line to center section and tighten. Rotate center section so the line almost hits the flange and tighten turbine clamp. 9. Install oil return line on center section with gasket. 10. Install water banjo fittings using supplied bolts and washers. 11. Install longer hose on front of turbo and shorter hose on back of turbo. 12. Install assembled turbo on header and tighten all bolts. 13. Install flange on oil pan with gasket use RTV on bolts tighten return line to flange. 14. Install AMS support bracket to block. Twist bolt hand tight against turbine housing then tighten nut securely. – check support bracket bolt every 500 to 1000 miles to make sure it is holding its place properly. 15. Install Downpipe and Secure clamp. 16. Install both dump tubes. Secure passenger side dump tube to bracket on downpipe. Secure drivers side dump tube to threaded hole in compressor housing. 17. Install banjo fitting to cylinder head and secure line. 18. Tighten water lines to stock water lines using supplied clamps. 19. Tighten compressor to center section clamp. 20. Install lower intercooler pipe. 21. Install supplied small radiator kit per instructions. 22. GET TUNED!

2010 TOYOTA PRIUS FOG LAMP KIT INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 23-05-2011

download
Items required for installation: Push pin 10mm bolt 10mm nut TOYOTA PRIUS 2010 FOG LAMP KIT 1 of 4 01-25-2010 STEP 3.2 • Attach fog lamp to bezel. STEP 3.3 • Fog lamp and bezel assembly. STEP 3.4 • Place fog lamp and bezel assembly onto vehicle. Fasten fog lamp to vehicle with 10mm nut and supplied screw. ( Repeat step 3 for passenger side ) STEP 4.0 Removal of interior trim on driver side STEP 4.1 • Pull up on lower door trim. STEP 4.2 • Foot panel-Remove 16mm plastic nut. STEP 4.3 • Pull foot panel inward toward center console. STEP 4.4 • Remove screw. STEP 4.5 • Disconnect hood release cable from latch by pulling down on the black cable freeing it from its location. Then moving the cable to the left away from the mounting bracket. STEP 4.6 • Remove cable from latch. STEP 4.7 • Pull lower left interior panel away from dash and unplug connectors. CAUTION! You may damage wiring and connectors if you pull too hard. Driver side interior removed. 2 of 4 01-25-2010 STEP 4.8 • Remove two screws and push back on tab to free lower panel. STEP 4.9 • Unplug connector and wire harness from panel and remove panel by pulling it toward the driver seat. STEP 5.0 Fog lamp switching wiring • Run WHITE wire through V-channel and pull female bullet connector end towards fire wall. • Connect ground wire to dashboard frame. STEP 5.4 • Plug green connector into fog lamp switch. (Plug all connectors removed from Step 4 and place panel back in position) STEP 6.0 Fog lamp wiring harness • From the panel removed under the steering wheel locate hole in grommet. STEP 6.1 • Puncture hole with O-ring pick/Philips screw driver or any sharp object no larger that the black tubing. (You want a tight seal between grommet and wire). STEP 5.1 • Remove tape from lower connector on ECU and locate BROWN wire. Use the bridge connector to connect RED wire to BROWN wire. You may need to cut RED wire to proper length. STEP 5.2 • Remove. STEP 5.3 • Replace with fog lamp switch. STEP 6.2 • Insert coat hanger or welding rod through punctured hole. Push rod far enough into engine compartment so you can retrieve it. STEP 6.3 • Bend tip or rod with needle nose pliers. STEP 6.4 • Insert hook end into bullet connector making sure black tubing is close to rod. V-channel Ground 3 of 4 01-25-2010 STEP 6.5 IMPORTANT! Wrap electrical tape around connector, tubing and rod. It is important that all three be secured as one unit so not to rip connector from wiring. You want tubing to take as much of the pull force as possible. STEP 6.6 • Apply soapy water to the entire length of black tubing and from the inside of the vehicle pull rod until wire breaks through grommet. 2.5-3ft of wiring should be sufficient. STEP 6.7 • Run wiring along side the black tube indicated until it meets female end of the WHITE fog lamp wire switch. STEP 6.8 • Connect both ends together and tie strap wiring to black tube. STEP 6.9 • On the top left corner of the fuse box (to the right of the brake fluid reservoir) locate silver ECU mounting bracket. STEP 6.10 • Remove 10mm bolts and attach BLACK ground and relay as indicated. STEP 6.11 • Attach harness connector to relay. STEP 6.12 • Run wire harness between ECU and fuse box. Run RED power wire along the same path as WHITE power wire in fuse box. Connect RED power wire to 12V power source directly above WHITE cable. STEP 7.0 Connecting wire harness to fog lamps • Run wiring for driver and passenger side lamps down toward driver side fog lamp. • Connect shortest harness to driver side fog lamp. Run wire harness alongside turn signal harness. • Use the supplied tie straps to secure passenger side wire harness along the radiator support frame shown. • Connect harness to fog lamp • END of installation

Related Content:

2010 prius fuse locations, Toyota Prius 2010 service manual, removing starter from 2005 crv, REMOVE AND REPLACE 2005 HONDA CRV STARTER, prius 2010 fuel pump fuse, kia rip radiator hose, ignition wire set 8MM Kia Sportage 2010 LX, how to change thermostat c arcadia, How do I remove the starter on a Chevy Cobalt 2006, Honda malfunction reset button location

1993 Dodge Dakota FUSE PANEL IDENTIFICATION

0

Filed Under (Dodge Manuals) by admin on 24-05-2011

download
3 – 10 Amp (Red) (1992-93); 15 Amp (Lt Blue) (1994-95) Back-Up Lights, A/C Electronic Cycling Switch (1992-93); Back-Up Lights, Airbag Module, Overhead Console (1994-95). 4 – Not Used (1992); 5 Amp (Tan) (1993-95) ABS Brake System. 5 – 20 Amp (Yellow) Power Door Locks. 6 – 15 Amp (Lt. Blue) Horn, Tachometer. 7 – 10 Amp (Red) Anti-Lock Brake Module, Stoplights, Buzzers. 8 – 20 Amp (Yellow) Taillights, Park, Side Marker Lights, Clock & Radio Display Intensity, License & Panel Lights. 9 – 15 Amp (Lt. Blue) Cigarette Lighter. 10 – 20 Amp (Yellow) Windshield Washers & Wipers. 11 – 20 Amp (Yellow) Turn Signals, Rear Wheel Anti-Lock Module. 12 – 10 Amp (Red) Radio. 13 – 4 Amp (Pink) Cluster Lights, A/C & Heater Controls, Cigarette Lighter Light & Ash Receiver Light, Radio Lights & Overdrive Switch Light. 14 – Not Used (1992-93); 15 Amp (Lt. Blue) (1994-95 Airbag Module, Speedometer, Gauges, Telltales. 15 – 2 Amp (Gray) Speed Control. 16 – 5 Amp (Tan) Gauges & Indicator Lights: Low Oil Light, Low Washer Light, Service Reminder Light, Transmission Oil Light, Brake Warning Light, Anti-Lock Brake Warning Light, Fuel Pacer Light, 4WD Indicator Light, Malfunction Indicator Light, Warning Buzzer, Overdrive Switch (1992-93); Transmission Oil Temperature Lamp, 4WD Lamp, Overdrive Module Seat Belt Warning Buzzer (1994-95). 17 – (Blank) Not Used. 18 – (Blank) Not Used. 19 – (Blank) Not Used. 20 – Not Used (1992-93); 25 Amp (Natural) (1994-95) Fog Lamps and Off Road Lamps. 21 – Turn Signal Flasher No additional definition. 22 – Time-Delay Relay No additional definition. 23 – Horn Relay No additional definition. 24 – Hazard Flasher No additional definition. 25 – Warning Buzzer

Related Content:

emission light on impala, 86 ford ranger emission sensors, 2011 dodge durango not charging, 1992 CHEVrolet silverado idle air control assembly calibration specifications, 1992 Grand Marquis Manual, mazda 3 transmission gear indicator light, service 4wd light on silverado, Isuzu NPR Warning Light Icons, slip light on nissan titan, how to reset washer fluid malibu 06

2001 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 18-02-2012

download
Wheel Hub Removal All vehicles 1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 . 2. NOTE: Caliper is removed for clarity. Position aside the front disc brake caliper and anchor plate (2B292). 1. Remove the two front disc brake caliper anchor plate bolts. 2. Remove the front disc brake caliper anchor plate and position aside. 3. NOTE: Carry out this step for F-250 and F-350 4×4 SRW vehicles. Remove the rotor. 4. NOTE: Carry out this step for DRW vehicles. NOTE: If excessive force must be used during brake rotor removal, the brake rotors should be checked for lateral runout prior to installation. For additional information, refer to Section 206-00 . Remove the eight hub extender nuts, the hub plate and the rotor. 1. Remove the eight hub plate nuts. 2. Remove the hub plate. 3. Remove the rotor. 5. Remove the hub lock. 1. Remove the retainer ring. 2. Pull outward and remove the hub lock. 6. Remove the axle shaft thrust washers. 1. Remove the snap ring. 2. Remove the three thrust washers. Vehicles equipped with ABS 7. sensor from the bearing. Disconnect the ABS wheel sensor harness. 1. Disconnect the connector. 2. Disconnect the harness routing clips. All vehicles 8. NOTE: The wheel hub and bearing is a slip fit design and should not require a puller to remove it. Remove the wheel hub and bearing. 1. Remove the four lock nuts. 2. Remove the wheel hub and bearing 9. If necessary, remove the brake disc shield. Vehicles with ABS 10. If necessary, remove the bolt and the ABS sensor. All vehicles 11. NOTE: If necessary, position the hub in a soft-jawed vise. Install two nuts on the studs and use the inner nut to remove the studs. 12. Remove and discard the O-ring. Installation All vehicles 1. NOTE: Any time the wheel hub is removed for any reason, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive operations. Install a new O-ring. 2. NOTE: Position the hub in a soft-jawed vise. Install two nuts on the studs and use the outer nut to install the studs. Vehicles equipped with ABS 3. Position the ABS sensor and install the bolt. All vehicles 4. Position the brake disc shield. 5. NOTE: Apply a coat of Ford High Temperature 4×4 Front Axle and Wheel Bearing Grease E8TZ-19590-A meeting Ford specification ESA-M1C198-A to the O-ring area of the wheel hub and bearing before installing the hub and bearing. Install the wheel hub and bearing. 1. Position the wheel hub and bearing. 2. Install the four lock nuts. Vehicle equipped with ABS 6. NOTE: The following step applies only to vehicles equipped with ABS. Connect the ABS sensor harness. 1. Position the ABS sensor harness and install the routing clips. 2. Connect the harness connector. All vehicles 7. n-metallic thrust washer must be installed between the two metal thrust washers. Failure to do so will cause severe wear to the non-metallic thrust washer, allowing the axle shaft to travel further in and out during torque thrust causing damage to the wheel hub and bearing, the axle shaft end seal and the axle shaft. Install the snap ring. 1. Position the three thrust washers onto the axle shaft. 2. Install the snap ring. 8. NOTE: Any time the hub lock is removed, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive functions. Install a new O-ring. 9. Install the hub lock. 1. Position the hub lock. 2. Install the retainer ring. 10. Position the front disc brake rotor (1125) to the wheel hub (1104). Make sure the wheel hub and the front disc brake rotor braking and mounting surfaces are clean. ? Use brake parts cleaner to clean the front disc brake rotor. 11. NOTE: Carry out this step for DRW vehicles only. Install the front wheel hub extender and nuts.

Related Content:

1995 ford 150 4 wheel drive front hub removal, how to replace wheel bearings on a 08 silverodo, Need to torque specifications 1999 GMC 1500 wheel hub bearings, 1977 ford f-350 rear wheel diagram, how to remove a rusted hub assembly, 1998 f250 4x4 front hub bearings torque specs, snap ring assemble, 2009 impala hub mounting bolt torque, Removing and repalcement2000 toyota tundra wheel bearing assembly, how to change rear hub assembly on a 2006-2010 saturn vue with disk brakes

V8 CHEVY CAMARO HEADER Y-PIPE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Chevy Manuals) by admin on 09-12-2011

download
Disconnect battery. 2. Lift or jack car to a comfortable height. 3. Using WD-40 spray all 6 collector studs and nuts, Y-pipe slip connect, all 4 cat pipe studs & nuts 4. Remove stock Y-pipe by removing the 2 bracket bolts and loosening up the slip connector clamp at rear then remove the 4 nuts holding the Y-pipe to the cat pipes. Slip Y-pipe out, and free from the car. 5. Remove all 4 of the O2 sensors (1) on driver manifold (1) on drive cat pipe (2) on passenger cat pipe. Four total. 6. Remove the 3 nuts on the driver side cat pipe and then remove the 3 nuts on the passenger cat pipe (be careful because the cats are heavy). 7. Remove all 8 spark plug wires. 8. Remove air tube on driver side manifold using a 10 mm socket. 9. Remove air tube on passenger side manifold using a 10 mm socket with universal. 10. Remove EGR tube on passenger side manifold using a 10″ extension with a 10 mm socket and universal. 11. Remove air pump on passenger side of engine and swing out of the way. 12. Remove EGR in front of manifold on top with a 10 mm socket and move to side. 13. Remove dipstick on passenger side 4. Remove all manifold bolts on passenger side and take manifold out. NOTE: Manifolds are Heavy 15. Remove all manifold bolts on driver side and take manifold out. NOTE: Manifolds are Heavy. 16. Unplug electrical hook up on EGR and move out of way. Note: Make sure plug wires are all the way on, and check after installation. Note: Save all stock gaskets, they will be used in installation. INSTALLATION OF BASSANI HEADERS 1. Use Bassani Jet lube on all threads 2. Install the 4 collector studs in headers 2 ea. On each side & snug down. 3. Use the stock exhaust gaskets and install the passenger side header from the bottom and install all of the header bolts then tighten them down after all of them are in. 4. Repeat step 3 for Drivers side. 5. Install the EGR tube on the lower passenger side of the Header. 6. Install the dipstick on Passenger side of engine and put the bolt in. 7. Install plug wires on Passenger side. 8. Install Air tube on Passenger side with supplied 5/16 Hardware. 9. Install EGR to front of motor and plug wire back in. 10. Install EGR tube on top of manifold with 10MM socket. 11. Install the air tube on Drivers side header with supplied 5/16 hardware and Stock Gasket. 12. Install Drivers side spark plug wires, make sure they are all the way on. 13. Install O2 Sensor in Drivers side header and tighten down. 14. Install new Bassani Cat pipe on Drivers side with Jet Lube and supplied 7/16-14 flange nuts and leave loose. 15. Install 2 ea. O2 Sensors in Passenger side Cat pipe

Related Content:

3406 e manual, passenger front side impala 2005

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, how to remove 2011 dodge durango grill, 2008 yaris hatchback remove headliner replace antenna, Redezvous Dash Removal, 2005 buick lesabre instrument cluster removal, remove 2010 highlander radio, remove fender 2001 grand prix, 2006 frontier remove window switch panel, remove front dash on 2014 optima