how to install fog lights in chevy cruze

You search PDF repair manual about how to install fog lights in chevy cruze, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to install fog lights in chevy cruze Direct Download speed 5432 Kb/s

  how to install fog lights in chevy cruze Full Version speed 8172 Kb/s



1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

0

Filed Under (Chevy Manuals) by admin on 14-05-2012

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, evap vacuum purge line collapsed on my 2001 oldsmobile silhouette, 2002 silverado remove front driveshaft, 2003 mitsubishi eclipse replace evapulator, how to remove malibu 2008 instrument gauge cluster cover, Redezvous Dash Removal, how to remove the heater core on 2000 VW Beetle, HOW TO REMOVE TOYOTA TACOMA FENDER LINER, 2004 Buick lesabre inrument cluster removeal

TOYOTA PRIUS FOG LIGHT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 18-03-2012

download
Remove the negative battery terminal Installation 1. Secure the relay to the next to the fuse block with wire ties 2. Attach the ring terminal with 2 black wires to ground 3. Attach fog light 12v red wire to open spade inside the fuse block as shown in picture 1 Picture 1 4. Locate the large vehicle harness grommet on the left side. Cut the auxiliary wiring access nipple off the grommet and push small 2-wire connector through firewall. Note: Extra caution should be taken not to damage connector 5. Run wires along the driver side of the engine compartment. Secure with wire ties as needed 6. From inside the cabin remove dash panels and locate the little small connector that was pushed through in step 4. Plug it to the switch harness. 7. T-tap orange/black wire from fog light harness to connector 2C pin 32 green wire. Pin 32 is on the left side of the connector 7th pin up from bottom of the connector. Connector 2C located left of the steering column above big white wire picture 2 Picture 2 8. T-Tap green/black wire from fog light harness to connector L47 pin 11, pink wire (it is the last pin to the left). Connector L47 is on the steering column and plugs into the headlight control arm picture 3 Picture 3 9. Mount switch into switch knockout of dash (picture 4) FOG LIGHT KIT INSTALLATION INSTRUCTIONS TPR-301 TOYOTA PRIUS 2010+ Picture 4 10. Install switch harness 11. Reinstall dash panels 12. Route the fog light wire under car. 13. Remove fog light cover plates and lower splash shields 14. Mount fog lights into bezel by sliding fog light tabs into slots and secure other side with supplied screw (see picture 5) Picture 5 15. Install both fog light bezels 16. Plug in left side fog light into harness plug 17. Run right fog light wire harness and plug into right fog light. Secure with wire ties 18. Reattach the lower splash shields

Related Content:

installing fog lights in 2012 sienna, how to connect fj cruiser corner fog lights, how to replace fog light on 2010 corolla youtube, 2010 corolla fog lamp installation, install instructions for fog lights on 2014 tacoma, install fog light 2013 sienna, install camry 2004 fog lights, how to replace fog light on 2010 corolla, how to install replacement fog lights in toyota rav 4 2014, how to install fog lights on a 2007 camry

2009 Toyota Corolla AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 07-07-2012

download
INSTALLATION 1. INSTALL FRONT AXLE HUB BEARING 2. INSTALL FRONT DISC BRAKE DUST COVER (a) Install the disc brake dust cover to the steering knuckle with the 3 bolts. Torque: 8.3 N·m (85 kgf·cm, 73 in·lbf) 3. INSTALL FRONT AXLE HUB SUB-ASSEMBLY 4. INSTALL FRONT AXLE HUB HOLE SNAP RING Last Modified: 4-24-2008 5.1 A From: 200712 Model Year: 2009 Model: Corolla Doc ID: RM000001IWX00ZX Title: AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION (2009 Corolla) (a) Using SST and a press, install a new front axle hub bearing to the steering knuckle. SST: 09950-60020 09951-00720 SST: 09950-70010 09951-07100 (a) Using SST and a press, install the front axle hub sub-assembly. SST: 09608-32010 SST: 09950-60010 09951-00600 SST: 09950-70010 09951-07100 5. INSTALL FRONT LOWER BALL JOINT 6. INSTALL FRONT AXLE ASSEMBLY 7. INSTALL FRONT LOWER SUSPENSION ARM 8. INSTALL TIE ROD END SUB-ASSEMBLY 9. INSTALL FRONT DISC 10. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY 11. TEMPORARILY INSTALL FRONT AXLE HUB NUT (a) Using snap ring pliers, install a new front axle hub hole snap ring. (a) Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly. (b) Install the front axle assembly to the front shock absorber with the 2 bolts and the 2 nuts. Torque: 240 N·m (2448 kgf·cm, 176 ft·lbf) Be careful not to damage the drive shaft boot or speed sensor rotor. Page 2of 4

Related Content:

calipers torque toyota corolla 2009, 2008 avalanche dtc code u0109, 2006 corolla front wheel hub assembly schematics, 2009 gm u0109, Repair manual hyundai accent 1 5 camshaft installation model 96, replace 2000 toyora corolla caliber bolts

V8 CHEVY CAMARO HEADER Y-PIPE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Chevy Manuals) by admin on 09-12-2011

download
Disconnect battery. 2. Lift or jack car to a comfortable height. 3. Using WD-40 spray all 6 collector studs and nuts, Y-pipe slip connect, all 4 cat pipe studs & nuts 4. Remove stock Y-pipe by removing the 2 bracket bolts and loosening up the slip connector clamp at rear then remove the 4 nuts holding the Y-pipe to the cat pipes. Slip Y-pipe out, and free from the car. 5. Remove all 4 of the O2 sensors (1) on driver manifold (1) on drive cat pipe (2) on passenger cat pipe. Four total. 6. Remove the 3 nuts on the driver side cat pipe and then remove the 3 nuts on the passenger cat pipe (be careful because the cats are heavy). 7. Remove all 8 spark plug wires. 8. Remove air tube on driver side manifold using a 10 mm socket. 9. Remove air tube on passenger side manifold using a 10 mm socket with universal. 10. Remove EGR tube on passenger side manifold using a 10″ extension with a 10 mm socket and universal. 11. Remove air pump on passenger side of engine and swing out of the way. 12. Remove EGR in front of manifold on top with a 10 mm socket and move to side. 13. Remove dipstick on passenger side 4. Remove all manifold bolts on passenger side and take manifold out. NOTE: Manifolds are Heavy 15. Remove all manifold bolts on driver side and take manifold out. NOTE: Manifolds are Heavy. 16. Unplug electrical hook up on EGR and move out of way. Note: Make sure plug wires are all the way on, and check after installation. Note: Save all stock gaskets, they will be used in installation. INSTALLATION OF BASSANI HEADERS 1. Use Bassani Jet lube on all threads 2. Install the 4 collector studs in headers 2 ea. On each side & snug down. 3. Use the stock exhaust gaskets and install the passenger side header from the bottom and install all of the header bolts then tighten them down after all of them are in. 4. Repeat step 3 for Drivers side. 5. Install the EGR tube on the lower passenger side of the Header. 6. Install the dipstick on Passenger side of engine and put the bolt in. 7. Install plug wires on Passenger side. 8. Install Air tube on Passenger side with supplied 5/16 Hardware. 9. Install EGR to front of motor and plug wire back in. 10. Install EGR tube on top of manifold with 10MM socket. 11. Install the air tube on Drivers side header with supplied 5/16 hardware and Stock Gasket. 12. Install Drivers side spark plug wires, make sure they are all the way on. 13. Install O2 Sensor in Drivers side header and tighten down. 14. Install new Bassani Cat pipe on Drivers side with Jet Lube and supplied 7/16-14 flange nuts and leave loose. 15. Install 2 ea. O2 Sensors in Passenger side Cat pipe

Related Content:

3406 e manual, passenger front side impala 2005

42R Turbo kit Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 19-03-2012

download
1. Open all boxes and inspect parts and verify from packing list that everything is there. 2. Find Turbo, Header, T4 Gasket, and Waste gates. 3. Carefully remove turbine housing from turbo. 4. Install 10×1.25 stud in location as indicated by picture. 5. Install Gasket and use nuts and bolts with lock washers to secure turbine housing to header.(use anti-seize on threads) 6. Carefully install the rest of the turbo to the turbine housing. Leave the clamps a little loose. (enough to rotate assemblies) 7. Use supplied TiAL gaskets and install waste gates to header. (use anti-seize to lube threads) 8. Install oil feed line to center section and tighten. Rotate center section so the line almost hits the flange and tighten turbine clamp. 9. Install oil return line on center section with gasket. 10. Install water banjo fittings using supplied bolts and washers. 11. Install longer hose on front of turbo and shorter hose on back of turbo. 12. Install assembled turbo on header and tighten all bolts. 13. Install flange on oil pan with gasket use RTV on bolts tighten return line to flange. 14. Install AMS support bracket to block. Twist bolt hand tight against turbine housing then tighten nut securely. – check support bracket bolt every 500 to 1000 miles to make sure it is holding its place properly. 15. Install Downpipe and Secure clamp. 16. Install both dump tubes. Secure passenger side dump tube to bracket on downpipe. Secure drivers side dump tube to threaded hole in compressor housing. 17. Install banjo fitting to cylinder head and secure line. 18. Tighten water lines to stock water lines using supplied clamps. 19. Tighten compressor to center section clamp. 20. Install lower intercooler pipe. 21. Install supplied small radiator kit per instructions. 22. GET TUNED!

2010 TOYOTA PRIUS FOG LAMP KIT INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 23-05-2011

download
Items required for installation: Push pin 10mm bolt 10mm nut TOYOTA PRIUS 2010 FOG LAMP KIT 1 of 4 01-25-2010 STEP 3.2 • Attach fog lamp to bezel. STEP 3.3 • Fog lamp and bezel assembly. STEP 3.4 • Place fog lamp and bezel assembly onto vehicle. Fasten fog lamp to vehicle with 10mm nut and supplied screw. ( Repeat step 3 for passenger side ) STEP 4.0 Removal of interior trim on driver side STEP 4.1 • Pull up on lower door trim. STEP 4.2 • Foot panel-Remove 16mm plastic nut. STEP 4.3 • Pull foot panel inward toward center console. STEP 4.4 • Remove screw. STEP 4.5 • Disconnect hood release cable from latch by pulling down on the black cable freeing it from its location. Then moving the cable to the left away from the mounting bracket. STEP 4.6 • Remove cable from latch. STEP 4.7 • Pull lower left interior panel away from dash and unplug connectors. CAUTION! You may damage wiring and connectors if you pull too hard. Driver side interior removed. 2 of 4 01-25-2010 STEP 4.8 • Remove two screws and push back on tab to free lower panel. STEP 4.9 • Unplug connector and wire harness from panel and remove panel by pulling it toward the driver seat. STEP 5.0 Fog lamp switching wiring • Run WHITE wire through V-channel and pull female bullet connector end towards fire wall. • Connect ground wire to dashboard frame. STEP 5.4 • Plug green connector into fog lamp switch. (Plug all connectors removed from Step 4 and place panel back in position) STEP 6.0 Fog lamp wiring harness • From the panel removed under the steering wheel locate hole in grommet. STEP 6.1 • Puncture hole with O-ring pick/Philips screw driver or any sharp object no larger that the black tubing. (You want a tight seal between grommet and wire). STEP 5.1 • Remove tape from lower connector on ECU and locate BROWN wire. Use the bridge connector to connect RED wire to BROWN wire. You may need to cut RED wire to proper length. STEP 5.2 • Remove. STEP 5.3 • Replace with fog lamp switch. STEP 6.2 • Insert coat hanger or welding rod through punctured hole. Push rod far enough into engine compartment so you can retrieve it. STEP 6.3 • Bend tip or rod with needle nose pliers. STEP 6.4 • Insert hook end into bullet connector making sure black tubing is close to rod. V-channel Ground 3 of 4 01-25-2010 STEP 6.5 IMPORTANT! Wrap electrical tape around connector, tubing and rod. It is important that all three be secured as one unit so not to rip connector from wiring. You want tubing to take as much of the pull force as possible. STEP 6.6 • Apply soapy water to the entire length of black tubing and from the inside of the vehicle pull rod until wire breaks through grommet. 2.5-3ft of wiring should be sufficient. STEP 6.7 • Run wiring along side the black tube indicated until it meets female end of the WHITE fog lamp wire switch. STEP 6.8 • Connect both ends together and tie strap wiring to black tube. STEP 6.9 • On the top left corner of the fuse box (to the right of the brake fluid reservoir) locate silver ECU mounting bracket. STEP 6.10 • Remove 10mm bolts and attach BLACK ground and relay as indicated. STEP 6.11 • Attach harness connector to relay. STEP 6.12 • Run wire harness between ECU and fuse box. Run RED power wire along the same path as WHITE power wire in fuse box. Connect RED power wire to 12V power source directly above WHITE cable. STEP 7.0 Connecting wire harness to fog lamps • Run wiring for driver and passenger side lamps down toward driver side fog lamp. • Connect shortest harness to driver side fog lamp. Run wire harness alongside turn signal harness. • Use the supplied tie straps to secure passenger side wire harness along the radiator support frame shown. • Connect harness to fog lamp • END of installation

Related Content:

2010 prius fuse locations, Toyota Prius 2010 service manual, removing starter from 2005 crv, REMOVE AND REPLACE 2005 HONDA CRV STARTER, prius 2010 fuel pump fuse, kia rip radiator hose, ignition wire set 8MM Kia Sportage 2010 LX, how to change thermostat c arcadia, How do I remove the starter on a Chevy Cobalt 2006, Honda malfunction reset button location

2001 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 18-02-2012

download
Wheel Hub Removal All vehicles 1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 . 2. NOTE: Caliper is removed for clarity. Position aside the front disc brake caliper and anchor plate (2B292). 1. Remove the two front disc brake caliper anchor plate bolts. 2. Remove the front disc brake caliper anchor plate and position aside. 3. NOTE: Carry out this step for F-250 and F-350 4×4 SRW vehicles. Remove the rotor. 4. NOTE: Carry out this step for DRW vehicles. NOTE: If excessive force must be used during brake rotor removal, the brake rotors should be checked for lateral runout prior to installation. For additional information, refer to Section 206-00 . Remove the eight hub extender nuts, the hub plate and the rotor. 1. Remove the eight hub plate nuts. 2. Remove the hub plate. 3. Remove the rotor. 5. Remove the hub lock. 1. Remove the retainer ring. 2. Pull outward and remove the hub lock. 6. Remove the axle shaft thrust washers. 1. Remove the snap ring. 2. Remove the three thrust washers. Vehicles equipped with ABS 7. sensor from the bearing. Disconnect the ABS wheel sensor harness. 1. Disconnect the connector. 2. Disconnect the harness routing clips. All vehicles 8. NOTE: The wheel hub and bearing is a slip fit design and should not require a puller to remove it. Remove the wheel hub and bearing. 1. Remove the four lock nuts. 2. Remove the wheel hub and bearing 9. If necessary, remove the brake disc shield. Vehicles with ABS 10. If necessary, remove the bolt and the ABS sensor. All vehicles 11. NOTE: If necessary, position the hub in a soft-jawed vise. Install two nuts on the studs and use the inner nut to remove the studs. 12. Remove and discard the O-ring. Installation All vehicles 1. NOTE: Any time the wheel hub is removed for any reason, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive operations. Install a new O-ring. 2. NOTE: Position the hub in a soft-jawed vise. Install two nuts on the studs and use the outer nut to install the studs. Vehicles equipped with ABS 3. Position the ABS sensor and install the bolt. All vehicles 4. Position the brake disc shield. 5. NOTE: Apply a coat of Ford High Temperature 4×4 Front Axle and Wheel Bearing Grease E8TZ-19590-A meeting Ford specification ESA-M1C198-A to the O-ring area of the wheel hub and bearing before installing the hub and bearing. Install the wheel hub and bearing. 1. Position the wheel hub and bearing. 2. Install the four lock nuts. Vehicle equipped with ABS 6. NOTE: The following step applies only to vehicles equipped with ABS. Connect the ABS sensor harness. 1. Position the ABS sensor harness and install the routing clips. 2. Connect the harness connector. All vehicles 7. n-metallic thrust washer must be installed between the two metal thrust washers. Failure to do so will cause severe wear to the non-metallic thrust washer, allowing the axle shaft to travel further in and out during torque thrust causing damage to the wheel hub and bearing, the axle shaft end seal and the axle shaft. Install the snap ring. 1. Position the three thrust washers onto the axle shaft. 2. Install the snap ring. 8. NOTE: Any time the hub lock is removed, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive functions. Install a new O-ring. 9. Install the hub lock. 1. Position the hub lock. 2. Install the retainer ring. 10. Position the front disc brake rotor (1125) to the wheel hub (1104). Make sure the wheel hub and the front disc brake rotor braking and mounting surfaces are clean. ? Use brake parts cleaner to clean the front disc brake rotor. 11. NOTE: Carry out this step for DRW vehicles only. Install the front wheel hub extender and nuts.

Related Content:

1995 ford 150 4 wheel drive front hub removal, Need to torque specifications 1999 GMC 1500 wheel hub bearings, snap ring assemble, 2009 impala hub mounting bolt torque, 1998 f250 4x4 front hub bearings torque specs, how to remove a rusted hub assembly, 1977 ford f-350 rear wheel diagram, removing rear axle bearing 2002 toyota tacoma, removing rear wheel bearing race in 06 f-250 super duty lariat, how to change rear hub assembly on a 2006-2010 saturn vue with disk brakes

2007 2008 Toyota Tundra 5.7L dual rear exit aft cat system Installation Manual

0

Filed Under (Toyota Manuals) by admin on 04-12-2011

download
Installation instructions: 1.) Raise and support vehicle. 2.) Lubricate all factory rubber hangers and fasteners with penetrating oil. 3.) Detach tailpipe from rear of factory muffler and slip hanger rods on tailpipe out of rubber hangers. Remove tailpipe from vehicle. 4.) Remove factory rubber hangers from hanger rods attached to muffler inlet pipes. 5.) Remove factory bolts attaching inlet pipe flanges to vehicle converter pipes; retain stock flange gaskets. 6.) Using stock gasket and bolts, attach supplied left muffler inlet pipe to mating flange of driver side converter pipe. Install factory rubber hanger onto hanger rod welded to pipe. 7.) Using stock gasket and bolts, attach supplied right muffler inlet pipe to mating flange of passenger side converter pipe. Install factory rubber hanger onto hanger rod welded to pipe. 8.) Place supplied 2.25? band clamps over inlets of muffler and install muffler onto inlet pipes with weld seam on muffler body facing up. 9.) Place one supplied 2.5? clamp over inlet of tailpipe section “D” and install pipe onto muffler outlet closest to drive-shaft. Insert hanger rod welded to pipe into corresponding factory rubber hanger just behind muffler 10.) Place one supplied 2.5? clamp over inlet of tailpipe section “E” and install pipe onto outlet of tailpipe section “D”. 11.) Install supplied fabricated hanger bracket, with two attached rods, to bottom of driver side frame rail as shown in Photo no.1. below. Use the supplied 5/16? hardware for attachment; there is an existing hole in frame to use for this purpose. 12.) Place one supplied 2.5? clamp over inlet of tailpipe section “H” and install pipe onto outlet of tailpipe section “D”. 13.) Install one supplied urethane hanger onto the hanger rods welded to the fabricated bracket and tailpipe section “H”. 14.) Place one supplied 2.5? clamp over inlet of tailpipe section “F” and install pipe onto remaining muffler outlet. 15.) Place one supplied 2.5? clamp over inlet of tailpipe section “G” and install pipe onto outlet of tailpipe section “F”. Insert hanger rod on pipe into stock rubber hanger next to spare tire. 16.) Referring to photo no.2 below, remove one stock bumper attachment bolt from each frame rail and replace with supplied 14mm bolts; the bolts closest to the front of the vehicle are the ones which need to be replaced. 17.) Install the supplied left and right tip hangers to the inside of the frame rails and onto the supplied bolts as shown in photo no. 2.; the slots in the brackets will index over the rear-most factory bolts when properly installed. Install the supplied 14mm nuts onto the supplied bolts to retain in place. 18.) Place two remaining 2.5? clamps over tip inlets and install tips onto outlets of tailpipes. 19.) Install remaining urethane hangers between hanger rods on tips and tip brackets attached to frame. Hanger rods on tips will point to the center of vehicle when correctly installed. 20.) Align all components for proper fit and clearance and tighten all clamps.

Related Content:

Rubber muffler hanger for Buick Riviera 95, chevrolet malibu 2007 crossover tube, toyota tundra 2010 spare tire removal, spare tire removal on 2002 tundra, silverado exhaust hanger extensions, section lower rear rail on 02 altima, 2000 bmw heater inlet pipe, removing spare tire from 2004 toyota tundra, how to replce the upper radiator water inlet pipe on a 2001 chevy cavalier, 2007 chevy malibu crossover pipe

2007 Toyota Tundra PRO STEP INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 20-05-2011

download
2 Side Bar Kit – Kit 84801 Before Starting Installation 1. Carefully read all warnings and instructions completely before beginning. 2. Verify all parts have been received in this kit by checking the parts list at the end of this document. 3. Only install this kit on the vehicle for which it is specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-3176. 4. Special tools needed: a. 17/64″ drill bit 5. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction. Engine Compartment 1. Disconnect both battery cables. Disconnect negative cable first, then positive cable. 2. Factory Side Bars a. Remove factory side bars if present. NOTE Kit parts are prefaced by the word kit and appear in bold print. NOTE If parts are missing from kit, please be prepared to provide the following information: 1. Name of purchase location 2. Bar Code on side of box 3. Date above bar code 4. Date inside box cover 5. Inspector # from inside box cover Positive Cable Negative Cable Prepare to Install Kit Drivers Side of Vehicle 1. Install kit brackets (body mounted). a. Install two kit brackets (body mounted) along driver side of vehicle using either two factory installed bolts per bracket,.or kit supplied 8mm bolts b. Repeat previous step on pass. side of vehicle. 2. Side Bars a. Insert kit sleeve into kit side bar (rear). Install kit bolt (7/16″ x 1″) and kit washer (7/16 USS flat) into kit sleeve . Underside of Body Kit Bracket Kit Side Bar (front) Short End Kit Side Bar (rear) Long End Side Bar (Passenger Side) Kit Sleeve 3 Side Bar Kit – Kit 84801 b. Install kit side bar (front) onto kit sleeve . Install kit bolt (7/16″ x 1″) and kit washer (3/8 USS flat) into kit sleeve . Install Side Bars on Vehicle 1. Install steps on vehicle a. Install the kit side bar assembly (driver) onto kit body brackets using four kit bolts (1/2″ X 1-1/ 4″), four kit washers (1/2″ flat), four kit sleeves (7/8″ OD), and four kit nuts (flange). Install the kit bolts into the outer holes in the kit body brackets . DO NOT TIGHTEN. NOTE The side bar can be installed in two positions. It can be installed so that the steps are flat or it can be installed with the steps slightly angled downward. Kit bolt (7/16″ x 1″), Kit Washer (3/8 USS flat ) Kit Body Bracket Outer Holes Kit Bolts (1/2 X1-1/4″) b. Determine desired position for the steps. Install four kit bolt (7/16″ x 3 1/2″), four kit washers (7/ 16″), and four kit nuts (flange nut) as indicated below. c. Tighten all mounting bolts on driver side of vehi- cle. d. Repeat for passenger side of vehicle. Install Step Pads on Side Bar 1. Step Pads a. Position kit step pads on center of kit side bar hoop . Ensure the kit step pad is level and mark two locations on each pad to drill

Related Content:

rear camber kit instruction for 07 impala, 2006 ford taurus flex pipe repair kit, vacuum windshield wiper model a ford kit repair, delphi alternator rebuild kit, owners manual for 1983 kit roadranger, installation of Fog Light Assembly 2011 Camry, 2000 blazer frame replacement, install cargo net 2014 impala, impala camber kit, how to replace the drivers side axel seal on an 2008 colbalt

1996-2000 Chevrolet And GMC Suburban/ Pick-Up 2500/ 3500 Series TUBULAR EXHAUST SYSTEM INSTALLATION INSTRUCTION

0

Filed Under (Chevrolet Manuals) by admin on 29-12-2011

download
Disassembly – Left Side 1. Disconnect negative cable from battery. 2. Use penetrating oil on all nuts and bolts to be removed. This will prevent the possibility of broken or stripped nuts and bolts. 3. Remove air cleaner system (note position of line and hose connections). 4. Disconnect spark plug wires. 5. Disconnect temperature sensor wire. 6. Remove EGR fitting. 7. Remove bolts and exhaust manifold. Disassembly – Right Side 1. Remove air cleaner box. 2. Disconnect spark plug wires. 3. Remove dipstick and dipstick tube. 4. Remove bolts and exhaust manifold. 5. Clean exhaust flange surfaces on both cylinder heads at this time. DISASSEMBLY – CROSSOVER PIPE 1. Raise vehicle and support with jackstands. 2. Disconnect and remove 02 sensors (2), being careful not to rupture or destroy the unit. WARNING: Do not clean this unit in any cleaning solvent and do not damage wire. 3. Between left and right side of the catalytic converter is a 3-bolt flange with gasket. From the front face of flange, measure out 15″ towards front of truck and cut stock exhaust pipes. Remove exhaust pipes from vehicle. NOTE: Before cutting pipes, measure the height of the converter from the bottom of the floor board for when you install new exhaust pipes you can maintain same distance. •ASSEMBLY – LEFT SIDE 1. Install T.E.S. flange gasket and one 3/8″-16 x 1″ bolt, lock washer, and thick flat washer at rearmost bolt hole (leave bolt loose enough to accept T.E.S.). 2. Install left side T.E.S. manifold from bottom side 3. Install all bolts and washers and tighten. Use thick flat washers on slotted holes. 4. Reinstall spark plugs. 5. Replace original equipment spark plug ends on cylinders #3 and #5 with 60° connectors and boots provided in kit. 6. Re-connect spark plug wires on left side. 7. Re-install temperature sensor wire to temperature sensor. ASSEMBLY – RIGHT SIDE 1. Install T.E.S. flange gasket and one 3/8″-16 x 1″ bolt, lock washer and thick flat washers at rearmost bolt hole (leave bolt loose enough to accept T.E.S.). 2. Install right side T.E.S. manifold from top side. Now install dipstick tube. 3. Install remaining bolts and lock washers. 4. Align all parts and tighten all right side bolts at this time. 5. Replace original equipment spark plug ends on cylinders #4, #6 and #8 with 60° connectors and boots provided in kit. 6. Re-connect right side spark plug wires. 7. To prevent contact with the hot T.E.S. tubing, use nylon tie wrap (supplied) to secure the heater hose to the a.c. dryer. 8. Re-install air cleaner box. CROSSOVER PIPE ASSEMBLY 1. With catalytic converters in their natural position, install and bolt exhaust extension pipes to header collectors using 3/8″ – 16″ x 2 1/2″ hex bolts, 3/8″ flat washers, 3/8″ lock washers and 3/8 hex nuts. Use the 3″ donut provided in kit. 2. Check alignment of pipes to the catalytic converter, secure bolts. 3. With everything in place, tack weld exhaust pipes to catalytic assembly. 4. Unbolt whole exhaust assembly from vehicle and let it hang. Complete weld around pipes. 5. Bolt assembly back in vehicle and check for clearance. 6. Re-install 02 sensors. Use anti-seize on threads of sensor. Route wires clear of exhaust system. 7. Lower vehicle to ground

Related Content:

2005 taurus exhaust system diagram, 2 2 s10 exhaust flange bolts, diagram of an exhaust system on a 2003 gmc envoy, Diagram of a exhaust crossover pipe for a 95 Oldsmobile aurora, 04 pacifica parts diagram, pontiac sunfire gt exhaust system diagram, how tight should exhaust, gmc yukon exhaust manifold diagram, 454 exhaust donut installation, 2006 corvette mid pipe flange torque

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, evap vacuum purge line collapsed on my 2001 oldsmobile silhouette, 2002 silverado remove front driveshaft, 2003 mitsubishi eclipse replace evapulator, how to remove malibu 2008 instrument gauge cluster cover, Redezvous Dash Removal, how to remove the heater core on 2000 VW Beetle, HOW TO REMOVE TOYOTA TACOMA FENDER LINER, 2004 Buick lesabre inrument cluster removeal