how to install sway bar on toyota tacoma

You search PDF repair manual about how to install sway bar on toyota tacoma, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to install sway bar on toyota tacoma Direct Download speed 5432 Kb/s

  how to install sway bar on toyota tacoma Full Version speed 8172 Kb/s



2005-2008 TOYOTA TACOMA 4 X 4 AND PRE RUNNER 3″ SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 31-03-2012

download
Tacoma Installation Instructions 09/09/08 INST-426A.DOC Page 2 of 7 FRONT OF TACOMA 1. Park vehicle on level concrete surface. 2. Center and lock the steering wheel. 3. Block the rear wheels of the vehicle to prevent vehicle from moving in either direction. 4. Jack up the vehicle from the lift point in Figure A. 5. Support the vehicle with jack stands from the points in Figure A. 6. Remove the front wheels. 7. Remove sway bar end links from spindle using 17mm socket (both sides). See Figure B. 8. Remove front skid plate using 12mm socket. 9. Remove sway bar from frame using 14mm socket. See Figure C. 10. Using 19mm socket, remove lower bolt and nut from the bottom of the strut (both sides). 11. Remove cotter key and 19mm nut from outer tie rod end, rack & pinion utilizing a tie rod end puller (or pickle fork). 12. Remove the three nuts (14mm) from the top of the strut. See Figure D. 13. Remove the struts from the vehicle, making sure that they are marked driver and passenger side respectively for reinstallation. NOTE: AT THIS TIME, IF YOU DO NOT HAVE A SUITABLE SPRING COMPRESSOR, IT IS HIGHLY ADVISED TO EITHER TAKE THE STRUT TO A QUALIFIED SERVICE CENTER OR PURCHASE THE REVTEK SC-1 SPRING COMPRESSOR. 14. Compress strut assembly and remove the nut (17mm) on the top of the strut shaft. 15. Release the compressor. 16. Remove the spring top plate from the strut. 17. Remove and discard the rubber spacer Tacoma Installation Instructions 09/09/08 INST-426A.DOC Page 3 of 7 FRONT OF TACOMA (continued) 18. Remove (hammer) the studs from the spring top plate. See Figure “F.” 19. Install (hammer) the LONGER STUDS (10MM) (provided) in the spring top plate. See Figure “G.” 20. Install the PRELOAD SPACER between the spring and the spring top plate with the small diameter facing toward the spring and the Revtek Industries logo facing outward. See Figure H. 21. Compress the strut assembly, making sure you center the strut shaft through the spring top plate hole and that the STUDS line up with the PRELOAD SPACER reliefs. Replace nut on the top of the strut shaft and torque to spec. (Torque specs can be found on page 1.) 22. Install the TOP OUT EXTENDER over the STUDS (Figure H). 23. Reinstall the strut by reversing the removal procedure; torque to spec. (Torque specs on page 1.) 24. When properly installed, Revtek Industries logo will be centered between preload spacer reliefs. 25. Reinstall tie rod ends, torque to spec. 26. Reinstall sway bar to frame. 27. Reinstall sway bar end links into spindles. Torque to spec

Related Content:

2005 tacoma shop manual free download, install rack and pinion 2006 tacoma, pdf how to replace 2003 prerunner steering knuckle, rack and pinion 99toyota tacoma install, skid plate install intructions for a 2014 toyota tacoma, torque specs for pressure plate 1997 tacoma 4x4, toyota avensis jacking points, toyota tacoma frame replacement procedures

1995-2004 TOYOTA TACOMA 4 X 4 AND PRERUNNER 3″ SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 29-02-2012

download
Tacoma 4WD & PreRunner Installation Instructions Page 3 of 7 09/09/08 INST-425F.DOC FRONT OF VEHICLE 1. Park vehicle on level concrete surface. 2. Center and lock the steering wheel. 3. Block the rear wheels of the vehicle to prevent vehicle from moving in either direction. 4. Jack up the vehicle from the lift point in Figure “A.” 5. Support the vehicle with jack stands from the points in Figure “A.” 6. Remove the front wheels. 7. Remove the nut (14mm) and the hardware from the anti-sway bar. See Figure “B.” 8. Remove the nut (19mm) and bolt (14mm) from the bottom of the strut. See Figure “C.” 9. Remove the three nuts (14mm) from the top of the strut. See Figure “D.” 10. Remove the strut from the vehicle. NOTE: AT THIS TIME, IF YOU DO NOT HAVE A SUITABLE SPRING COMPRESSOR, IT IS HIGHLY ADVISED TO EITHER TAKE THE STRUT TO A QUALIFIED SERVICE CENTER OR PURCHASE THE REVTEK SC-1 SPRING COMPRESSOR. 11. Compress strut assembly and remove the nut (17mm) on the top of the strut shaft in Figure “E.” 12. Release the compressor. 13. Remove the spring top plate from the strut. 14. Remove and discard the rubber spacer. 15. Remove (hammer) the studs from the spring top plate. See Figure “F.” 16. Install (hammer) the LONGER STUDS (10MM) (provided) in the spring top plate. See Figure “G.” 17. Install the PRELOAD SPACER between the spring and the spring top plate with the small diameter facing toward the spring. See Figure “H.” 18. Compress the strut assembly, making sure you center the strut shaft through the spring top plate hole and that the STUDS line up with the PRELOAD SPACER reliefs. Replace nut on the top of the strut shaft and torque to spec. (Figure “E”). (Torque specs can be found on page 1.) 19. Install the TOP OUT EXTENDER over the STUDS (Figure “H”). 20. Reinstall the strut by reversing the removal procedure; torque to spec. (Torque specs on page 1.) 21. When properly installed, PRELOAD SPACER relief and Revtek Industries logo should face outward. (Figure R) 22. Reinstall hardware and nut on anti-sway bar; torque to spec. 23. Replace the wheels; torque to spec.

Related Content:

TORQUESPECLINCOLN2000

1995-2000 Toyota Tacoma DROP KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 03-12-2011

download
Removing Factory Parts. 1) Park your truck on a flat, level, concrete surface. Measure and record the wheel well height on installation helper. Chock the rear wheels. Loosen front lug nuts. Raise the front with a floor jack. Support the frame with jack stands. Remove front wheels. NOTE : ALWAYS USE JACK STANDS – NEVER RELY ON JACKS ONLY!! 2) Working on one side at a time. Remove front shocks. Remove front sway bar end links from sway bar and the bracket bolted to stock lower control arm. Remove the tie rod end from spindle. Keep all hardware, you will need it to reinstall later. 3) Support the lower control arm with floor jack. Remove upper ball joint nut and separate from spindle. Remove the two bolts that attach the lower ball joint bracket to the spindle, located on each side of the lower ball joint. SECURE SPINDLE TO FRAME WITH SAFETY WIRE. DO NOT LET SPINDLE HANG FROM BRAKE LINE!! Note position o factory parts. Fig 1 & 2. 4) Loosen the two bolts holding the upper control arm shaft to the frame. Carefully remove the alignment shims and keep together. Note forward and rearward, you will install them the same way they were removed. Remove upper control ar mounting bolts and remove upper arm. Keep all hardware 5) Next remove the two nuts on the bottom of the control ar holding the sway bar bracket and tensioncomperssion rod (TC) to lower arm. Remove the TC pivot bolt and remove TC rod fro vehicle. The two studs are pressed into the TC rod. Keep the TC pivot bolt, you will need use it later. 6) Remove the two nuts on the outer end of the lower arm that hold the spindle mounting bracket and remove bracket. The two studs are pressed into the bracket. When all these parts are removed the lower arm will look like the picture in Fig 3. Note coil spring removed for photo.

1995-2004 Toyota Tacoma/ 2000-2006 Tundra 2″ Leveling Kit Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 02-03-2012

download
Front Installation: 1. Secure and properly block the tires of vehicle on a level concrete or asphalt surface. 2. Raise the vehicle from the front center cross member and remove tires and wheels. (See Photo #1) 3. Disconnect outer tie rod from steering knuckle. Remove cotter pin. (See Photo #2), It may be necessary to strike the side of the knuckle to dislodge the tie rod end. Be careful not to damage the tie rod end itself. 4. Disconnect the ABS line from the upper A-ARM.. 5. Disconnect the sway bar end link from the frame and the side of the steering knuckle (See Photo #3). Disconnect the upper ball joint from the top of the steering knuckle. 6. Remove the upper three strut mounting bolts from the upper frame. (See Photo #4). Remove strut assembly from vehicle. 7. Locate supplied 7/16″ studs and new front Aluminum Spacers. Apply thread locking compound to the coarse thread portion of the studs. Thread in studs by hand until tight. (See Photo #5) 8. With studs installed, attach aluminum spacer to the top of the factory strut using the factory studs and nuts. Note: The Tundra factory studs will need to be ground down 1/4″ for proper clearance.(See Photo #6) Torque to 45 Ft. Lbs. 9. Install new strut assembly. Attach with new upper 7/16″ retaining nuts and washers. (See Photo #7) Only start the nuts at this time. 10. With upper nuts started, install lower shock retaining bolt @ the A- Arm. 11. Using a floor jack to raise the lower A-Arm, Re-Attach upper ball joint to steering knuckle.

Related Content:

picture diagram of how to install a toyota tacoma body lift kit#5533, yhsm-inucbr_001

Related Content:

2005 tacoma shop manual free download, install rack and pinion 2006 tacoma, pdf how to replace 2003 prerunner steering knuckle, rack and pinion 99toyota tacoma install, skid plate install intructions for a 2014 toyota tacoma, torque specs for pressure plate 1997 tacoma 4x4, toyota avensis jacking points, toyota tacoma frame replacement procedures