how to program ecm kia

You search PDF repair manual about how to program ecm kia, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to program ecm kia Direct Download speed 5432 Kb/s

  how to program ecm kia Full Version speed 8172 Kb/s



2000-2002 Infiniti G20 MIL “ON” REAR O2 SENSOR DTC P0138/P0139/P0140 Repair Manual

0

Filed Under (Infiniti Manuals) by admin on 17-02-2012

download
SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies. • ECM Reprogramming (required if the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A -page 2). • Replacing the Rear Oxygen Sensor (required if ECM Reprogramming is needed). Determine the DTC Stored in ECM: 1. Determine which DTC code is stored in the vehicle’s ECM by performing CONSULT-II Self-Diagnosis. 2. Print out the Self-Diagnosis results for use in ECM Part Number Check , below. See Figure 1 for an example of the CONSULT-II Self-Diagnosis printout. Figure 1 SELF-DIAG RESULTS SYSTEM ENGINE DATE 03/15/2002 3:35:35 P/N 23710-7J400 DTC Code TP020169 DTC RESULTS TIME HO2S2 (B1) 3 [P0138] Current ECM Part Number 2/3 ECM Part Number Check 1. Compare the vehicle’s current ECM P/N (from your CONSULT-II Self Diagnosis printout) to those shown under Current ECM P/N in Chart A , below: Chart A – Current ECM P/N’s: Vehicle Current ECM P/N 2000 M/T 23710-7J400, -7J401, -7J402, -7J460 2000 A/T 23710-7J410, -7J411, -7J412, 7J470 2001-2002 M/T 23710-6J105, -6J106, -6J107, -6J108, 6J170 2001-2002 A/T 23710-6J115, -6J116, -6J117, -6J118, -6J180 A. If the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A (above): • Look in the “Vehicle” Column in Chart A (above) and determine the vehicle “configuration” (i.e. 2002 M/T). Make a note of the vehicle configuration and perform ECM Reprogramming , below. B. If the ECM P/N in the vehicle does not match one of those listed under “Current ECM P/N” in Chart A (above): • This bulletin does not apply. Use the appropriate Electronic Service Manual (ESM) to further diagnose and repair the incident. ECM Reprogramming 1. Perform ECM Reprogramming to install the latest available ECM data. • If you are unfamiliar with ECM Reprogramming, click here to link to the “ECM Reprogramming For Infiniti Vehicles” general procedure or refer to Attachment A in the print copy of this bulletin. • For those familiar with ECM Reprogramming, perform the following:

Related Content:

99 hyundai ecm fuse location, hino dutro vnt circuit open, 2002 Ford Windstar Repair Manual, 2002 saturn vue repair manual free, 2002 taurus ecm removal, Free 2002 BMW Service Manual, saturn 2002 l300 maf volts, 2002 vw passat repair manual, 2001 pontiac sunfire P0502, 2000 saturn l300 ecm replacement

1999-2001 Infiniti Q45 MIL “ON” REAR O2 SENSOR DTC SERVICE PROCEDURE

0

Filed Under (Infiniti Manuals) by admin on 07-01-2012

download
SERVICE PROCEDURE You will be performing the following, as required: • Determine the DTC Stored in ECM from the CONSULT-II Self-diagnosis results. • ECM Part Number Check to determine if this bulletin applies. • ECM Reprogramming (required if the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A -page 2). • Replacing the Rear Oxygen Sensor (required if ECM Reprogramming is needed). Determine the DTC Stored in ECM: 1. Determine which DTC code is stored in the vehicle’s ECM by performing CONSULT-II Self-Diagnosis. 2/4 2. Print out the Self-Diagnosis results for use in ECM Part Number Check , below. See Figure 1 for an example of the CONSULT-II Self-Diagnosis printout. ECM Part Number Check 1. Compare the vehicle’s current ECM P/N (from your CONSULT-II Self Diagnosis printout) to those shown under Current ECM P/N in Chart A , below: Chart A – Current ECM P/N’s: Vehicle Current ECM P/N 1999-2001 Q45 23710-3H000, -3H001, -3H005, -3H006, -3H007 A. If the ECM P/N in the vehicle matches one of those listed under “Current ECM P/N” in Chart A (above): • Perform ECM Reprogramming on page 3. B. If the ECM P/N in the vehicle does not match one of those listed under “Current ECM P/N” in Chart A (above): • This bulletin does not apply. Use the appropriate Electronic Service Manual (ESM) to further diagnose and repair the incident. SELF-DIAG RESULTS SYSTEM ENGINE DATE 01/24/2002 5:35:07 P/N 23710-3H000 DTC Code TP020024 DTC RESULTS TIME HO2S2 (B1) 3 [P0138] Current ECM Part Number 3/4 ECM Reprogramming 1. Perform ECM Reprogramming to install the latest available ECM data. • If you are unfamiliar with ECM Reprogramming, click here to link to the “ECM Reprogramming For Infiniti Vehicles” general procedure or refer to Attachment A in the print copy of this bulletin. • For those familiar with ECM Reprogramming, perform the following:

Related Content:

2007 ecm location saturn vue, 2008 chevy 3 5 repair manual, how to replace ECU on 2005 Cadillac CTS, infiniti q45 manual torrent, mercedes cis repair manual pdf, manual pdf de hino dutro, lincoln ecm reprogramming, instructional how to reset the ECM on a 2004 Cadillac CTS, Ford 1998 E350 loction of the ecm, ecm update audi 2006 list

NISSAN ALTIMA OR SENTRA W /QR25 ENGINE NO-START AFTER COLD SOAK REPAIR MANUAL

0

Filed Under (Nissan Manuals) by admin on 10-05-2012

download
SERVICE PROCEDURE Replace Starter, Add Cleaner 1. Replace the starter motor. • Use the part number from the Parts Information section of this bulletin. • Refer to section SC, “STARTING SYSTEM, Removal and Installation” in the applicable Nissan Electronic Service Manual (ESM). 2. Add one full can of Nissan In-Tank Fuel System Cleaner to the fuel. NOTE: If the fuel tank is less than ¾ full, instruct the customer to fill the tank as soon as it is convenient after the repair. Driving with the Cleaner installed and low fuel level will not harm the fuel system or engine, but will reduce the effectiveness of the cleaning process. 3. Continue to ECM Part Number Check (next page). 1. With CONSULT-II “ON”, print the Self-DIAG Results as follows: START (Nissan) >> ENGINE >> Self-DIAG Results >> PRINT SELF-DIAG RESULTS SYSTEM ENGINE DATE XX/XX/XXXX* 11:07:11 P/N 23710-XXXXX TP020389h DTC RESULTS TIME NO DTC IS DETECTED Current ECM Part Number * Example, your screen may differ. 3. Using the printout from Step 1: • Compare the vehicle’s current ECM P/N to those shown under Current ECM P/N in Chart 1, below: • This comparison will allow you to determine if the ECM needs to be reprogrammed. Chart 1, Current ECM P/N’s: VEHICLE PACKAGE NATS? CURRENT ECM P/N A/T, ASCD YES 23710-9J305, -9J003, -9J002, -9J001, -9J000, -8J001, -8J000 M/T, ASCD YES 23710-9J315, -9J013, -9J012, -9J011, -9J010, -8J061, -8J060 A/T, no ASCD YES 23710-9J300, -9J008, -9J007, -9J006, -9J005, -8J011, -8J010 02-04 Altima M/T, no ASCD YES 23710-9J310, -9J018, -9J017, -9J016, -9J015, -8J071, -8J070 YES 23710-8U542, -8U541, -8U540, -8U041, 8U040 A/T NO 23710-8U502, -8U501, -8U500, -8U001, 8U000 YES 23710-8U562, -8U561, -8U560, -8U061, -8U060 02-03 Sentra 5 M/T NO 23710-8U512, -8U511, -8U510, -8U011, -8U010 YES 23710-8U072, -8U071, -8U070 02 Sentra 6 M/T NO 23710-8U022, -8U021, -8U020 YES 23710-8U572, -8U571, -8U570 03 Sentra 6 M/T NO 23710-8U522, -8U521, -8U520 NOTE: The 2004 Sentra ECM does not need to be reprogrammed for this bulletin. A. If your vehicle’s ECM P/N matches a P/N in the chart above: • Perform ECM Reprogramming (page 4). B. If your vehicle’s ECM P/N does not match a P/N in the chart above: • ECM Reprogramming is not necessary, bulletin complete / end here

Related Content:

free repair manuals 2002 nissan sentra, 87 NISSAN SENTRA CARBURETOR AIR HORN REMOVAL, nissan rear undercarriage for altima, p1760 en 96 nissan quest

2003-2004 Accord V6 MIL Comes On With DTC P2195 or P2197 REPAIR PROCEDURE

0

Filed Under (Honda Manuals) by admin on 06-06-2011

download
Before you update an ECM/PCM, make sure the battery in the vehicle is fully charged. •To prevent ECM/PCM damage, do not operate anything electrical (audio system, brakes, A/C, power windows, moonroof, etc.) during the update. 1. If not already done, load the May 2004 or later i N CD onto the i N master terminal. Loading instructions are included with the CD. 2. Update the ECM/PCM software with the HIM. For updating instructions, refer to Programming the HIM and Updating an ECM/PCM With a Programmed HIM in Service Bulletin 01-023, Updating Control Units/Modules . 3. Warm up the engine to operating temperature, then shut if off. 4. Do the ECM/PCM RESET and the CKP PATTERN CLEAR with the HDS. OP# Description FRTTemplate ID 123503Retrieve the DTC(s), and clear the codes with the HDS. 0.3 04-038A 125517Update the ECM/PCM software with the Honda Interface Module. 0.3 122505Do the CKP pattern learn. 0.32 of 2 04-038 5. Do the ECM/PCM idle learn procedure: •Make sure all electrical items (A/C, audio, rear window defogger, lights, etc.) are off. •Turn the ignition switch to the ON (II) position for 30 seconds. •Start the engine, and let it idle (throttle closed and all electrical items off) for 10 minutes. 6. Do the low-rpm CKP pattern learn: •Test-drive the vehicle on a level road: With the A/T in second gear, or the M/T in second or third gear, decelerate (with the throttle fully closed) from 2,500 rpm down to 1,000 rpm . •Stop the vehicle, and put the transmission into Park or Neutral. Set the parking brake. Do not turn off the ignition switch. 7. Connect the HDS to the DLC, and check the status of PULSER F/B LEARN: •On the Selection Menu , select PGM-FI . •On the Mode Menu , select Data List . •Check the value of PULSER F/B LEARN . •If the value is Completed , go to step 7. •If the value is Not Completed , be sure the engine is at normal operating temperature (the ECT SENSOR (1) value is 176 or higher), and return to step 5. 8. Do the high-rpm CKP pattern learn: NOTE: The low-rpm CKP pattern learn must be completed before you do the high-rpm CKP pattern learn. •Test-drive the vehicle on a level road: With the A/T in first gear, or the M/T in first gear, decelerate (with the throttle fully closed) from 5,000 rpm down to 3,000 rpm . •Stop the vehicle, and put the transmission into Park or Neutral. Set the parking brake. Do not turn off the ignition switch. 9. Connect the HDS to the DLC (if not already connected), and do this: •On the Selection Menu , select PGM-FI . •On the Mode Menu , select Data List . 10. Check the value of PULSER F/B LEARN (HIGH RPM) •If the value is Completed , you are finished. Disconnect the HDS. •If the value is Not Completed , be sure the engine is at normal operating temperature (the ECT SENSOR (1) value is 176 or higher), and repeat steps 5 thru 8

Related Content:

kia ceed hidden menu, reset computer on 2004 buick rendevous, kia t s b 04-40-015, kia ceed secret menu, kia ceed menu secret, 2004 accord pcm update, kia ceed 3 hidden menu, how do you do a (pcm) reset & (ckp) pattern clear/learn procedure on a 2007 honda pilot?, CKP pattern learn procedure honda odyssey, 2004 honda accord 6 cylinder EX obd-II P2195

2001 Volkswagen Passat GLX 4Motion UPDATE PROGRAMMING FOR CATALYTIC CONVERTER SYSTEM Manual

0

Filed Under (Volkswagen Manuals) by admin on 26-06-2012

download
Programming software update. SERVICE PROCEDURE Engine Control Module Update – Programming (Flashing) Tip: When performing the update programming procedure, ALL DTCs for all systems are erased. DTCs linked to Guided Fault Finding function tests will be lost. Therefore, always address stored DTCs for Customer concerns unrelated to the update programming procedure first. The following “Update – Programming” (flashing) process may overwrite any “TUNED” ECM programming. A “TUNED” ECM is described as any ECM altered so as to perform outside the normal parameters and specifications approved by Volkswagen of America, Inc. If you encounter a vehicle with a “Tuned” ECM, prior to performing the “Update – Programming” (flashing) procedure: Your Dealership should place the vehicle owner on notice in writing, that their ECM was found to have been tuned, and that any damage caused by the tuning of the ECM (including any adverse emissions consequences) will not be covered by Volkswagen of America, Inc. warranties. For any repair requested by the owner under warranty or outside warranty that requires update programming, which will automatically wipe out the “Tuning” program, your Dealership should advise the owner of the above and get Owner’s written consent (see attached Control Module Tuning form) to the update programming procedure. Tool Requirements VAS 5051 or VAS 5052 (with Base CD V.10.01 and the Brand CD V.10.70.00 or higher). “Update – Programming” (flashing) CD 8D0906961A, B, D. Tip: Additional copies of the “Update – Programming” CD (Literature Number 8D0906961A, B, D) may be ordered from the Volkswagen Technical Literature Ordering Center at www.vw.resolve. com , or by calling 1- 800-544-8021 from 8:00 a.m. to 8:00 p.m. EST Monday through Friday. This number can be dialed in both the United States and Canada

Related Content:

86 chevy silverado manual, hunter gsp9200 parts diagram, 2013 camaro owners manual pdf, is there a certain pattern for props on hubsan x4, oil pump diagram 99 audi a6 auattro 2 8 pdf, owners manual 98 cavalier, quicksilver 3000 installation manual, remove bed slide 1000, Repair frame of Hubsan X4form=LENDF8pc=LEN2src=IE-SearchBox, hubsun x4 wiring

1999 NISSAN MAXIMA NO START AND SECURITY LAMP ON WITH NATS DTC “ID DISCORD, IMM-ECM” REPAIR MANUAL

0

Filed Under (Nissan Manuals) by admin on 29-05-2012

download
SERVICE PROCEDURE NOTE: This procedure is described using CONSULT-II. CONSULT may also be used to perform the diagnostic procedures outlined below. However, the screens and steps will differ slightly from those shown here. 1. Install the NATS card (purple) into slot 1 of CONSULT-II (see Figure 1). Figure 1 2/9 2. Connect CONSULT-II to the vehicle (see Figure 2). Figure 2 3. Turn the ignition switch to “ON” (do not start the engine). CONSULT-II will then turn on automatically (see Figure 3). Now touch “START”. Figure 3 4. Select “NATS V2.0″ (see Figure 4). Figure 4
3/9 5. Select “SELF DIAGNOSIS” (see Figure 5). Figure 5 6. Confirm Self Diagnosis Result “ID DISCORD, IMM-ECM” displayed on the CONSULT-II screen (see Figure 6). Figure 6 7. Press “COPY” to print the Self-Diagnosis screen (see Figure 6). Attach this printout to the repair order. Then press “BACK” (see Figure 6) to return to the CONSULT-II main menu. 4/9 8. Turn the vehicle’s ignition switch “OFF” and CONSULT-II “OFF” (see Figure 7). Figure 7 9. Remove the NATS (purple) card from CONSULT-II and install the Diagnostics (blue) card (see Figure 8). Figure 8 5/9 10.Turn the ignition switch to “ON” (do not start the engine). CONSULT-II will then turn on automatically (see Figure 9). Now touch “START”. Figure 9 11.Select “ENGINE” (see Figure 10). Figure 10 6/9 12.Select “ECM PART NUMBER” (see Figure 11). Figure 11 13.Press “COPY” to print the ECM PART NUMBER screen (see Figure 12). Attach this printout to the repair order . Then press “BACK” to return to the CONSULT-II main menu. Figure 12 7/9 14.Turn the vehicle’s ignition switch “OFF” and CONSULT-II “OFF”. 15.Compare the vehicle’s ECM PART NUMBER as printed from CONSULT-II in step 13 to the ECM # in the chart below.

Related Content:

nissan consult 2 nats card, nissan consult 2 program cards

1999 Buick Regal DTC B1001 Option Configuration Error Repair Manual

0

Filed Under (Buick Manuals) by admin on 02-07-2012

download
Test Description The number(s) below refer to the step number(s) on the diagnostic table. 2. This step checks to see if the correct VIN is programmed in the powertrain control module (PCM). 4. This step checks to see if the body control module (BCM) has been replaced. 5. This step explains the proper steps to perform after a BCM has been replaced in order for the <- Back Forward -> Document ID# 385021 1999 Buick Regal Print BCM to operate properly. 6. This step checks to see if the correct VIN is programmed in the BCM. 7. This step explains how to properly program the VIN into the BCM. DTC B1001 Option Configuration Error Step Action Value (s) Yes No 1 Was the SIR Diagnostic System Check performed? — Go to Step 2 Go to SIR Diagnostic System Check 2 1. Install the scan tool. 2. Use the scan tool to verify that the PCM is programmed with the correct VIN by comparing the VIN that is stored in the PCM to the VIN plate of the vehicle. Is the PCM programmed with the correct VIN? — Go to Step 4 Go to Step 3 3 Use the scan tool and/or the techline machine to program the correct VIN into the PCM. Is the programming procedure complete? — Go to Step 9 — 4 Was the BCM replaced? — Go to Step 5 Go to Step 6 5 1. Use the F2 function key and follow the instructions on the scan tool under the BCM SPECIAL FUNCTIONS to reprogram the BCM. This allows the BCM to learn the Restraints ID from the SDM and also to learn other important data that is required. 2. Use the F6 function key and follow the instructions on the scan tool under the BCM SPECIAL FUNCTIONS to program the correct VIN into the BCM. 3. Use the techline machine to perform the theft relearn procedures for the replacement BCM. Are the programming procedures complete? — Go to Step 9 — 6 Use the scan tool to verify that the BCM is programmed with the correct VIN by comparing the VIN that is stored in the BCM to the VIN that is stored in the PCM. Is the BCM programmed with the correct VIN? — Go to Step 8 Go to Step 7 7 Use the F6 function key and follow the instructions on the scan tool under the BCM SPECIAL FUNCTIONS to program the correct VIN into the BCM. Is the reprogramming procedure complete? — Go to Step 9 — 1. Turn the ignition switch to the OFF position. 2. Replace the SDM. Refer to Inflatable Restraint

Related Content:

GM BCM Repair, diagnostic tester for cummins n14, kia sedona 2004 pcm, reprogram BCM 2003 saturn vue, HOW TO CHANGE A BCM ON A 2001 300M, 2008 buick enclave anti theft relearn procedures, 1999 Chevy Blazer Repair Manual, were is the bcm on a 02 malubu, how to reset a body control module on a 2005 gmc envoy, how tp reset a bcm on 07 silverado

2001-2003 RAV4 HARSH SHIFT AND/ ORM.I.L. “ON”DTC P0750, P0755, P0758, AND/ ORP1760 REPAIR MANUAL

0

Filed Under (Toyota Manuals) by admin on 10-02-2012

download
HARSH SHIFT AND/ORM.I.L. “ON”DTCP 0750, P0755, P0758, AND/ORP1760 –TC 002-06 Revised March3,2006 Page 2of3 PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME QTY 89661–42650 1 89661–42651 89661–42653 1 89661–42652 1 89661–42660 1 89661–42661 89661–42663 Engine Control Module (ECM) 1 89661–42662 Engine Control Module (ECM) 1 89661–42810 89661–42811 1 89661–42820 89661–42821 1 89661–42880 Same 1 89661–42890 Same 1 ITEM NO. SPECIAL SERVICE TOOLS (SSTs) PART NUMBER QTYDRW** 1 Toyota Diagnostic Tester Kit* NOTE: SAll components from this kit/set are required S12 MegabyteDiagnostic Tester Program Card (P/N 01002593–005) with version 13.3aSoftware (or later) is required TOY220036 1 9 *Essential SSTs. **Referstodrawer number in SST Storage System. NOTE: Additional Diagnostic Tester Kits, Program Cards, or other SST smaybeorderedby callingSPX/OTC at 1-800-933-8335. 1. If the vehicle is currently exhibiting a harsh shift condition and/or M.I.L. “ON”with DTCP0750, P0753, P0755, P0758, and/or P1760 stored, refer to the Technical Information System (TIS), 2001–2003 model year RAV4 Repair Manual: S4WD: Diagnostics/Automatic Transaxle (U140f): Problem Symptoms Table S2WD: Diagnostics/Automatic Transaxle (U142E): Problem Symptoms Table NOTE: In some instances the vehicle must be operated at least 30 minutes before the condition can be duplicated. 2. If the vehicle exhibits the above condition, replace the ECM (PCM). Parts Information Required SSTs

Related Content:

2006 toyota rav4 repair manual download

1994-2003 Ford F-Series Power Stroke 7.3L Edge Evolution Programmer Installation Manual

0

Filed Under (Ford Manuals) by admin on 25-05-2012

download
Connecting the Evolution 1. Turn the ignition switch to the OFF position. Locate the diagnostic connector under the dash near the steering column or under the glove compartment and connect the Evolution cable to this connector. After making the connection, the screen will first display the Edge Products logo and then the main startup displays: The numbers in the upper left portion of the screen represent the version number of the Evolution programmer. The character in the upper right portion of the screen represents the current programmed state of your vehicle. The following letters may appear: I – Programming was interrupted. (See Programming Interrupted section for more information) 1 – Vehicle has been programmed to L1 – TOW. 2 – Vehicle has been programmed to L2 – RACE. 3 – Vehicle has been programmed to L3 – EXTREME. Evolution FORD Power Stroke 7.3 Liter 11 2. Select your desired option by pressing the up or down keys on the left side of the programmer and press . Continue to the next section. Evolution FORD Power Stroke 7.3 Liter 12 Power Programming “Caution: Vehicle manufacturers do not recommend vehicle programming in extreme temperature. Please see the service manual of your vehicle to ensure that programming is being done in accordance to the original equipment manufacturers specifications.” If you selected Diagnostics from the Main Menu, go to that section in this instruction manual and follow the steps. If you selected Performance from the Main Menu, go to that section in this instruction manual and follow the steps. If you selected Power Programming, the screen displays the following message: 1. After turning the key ON (do not start the engine) and pressing , the screen displays the following message: Evolution FORD Power Stroke 7.3 Liter 13 Evolution FORD Power Stroke 7.3 Liter 14 2. The Evolution will check the PCM and determine if it is in the Master Calibration list. If the calibration is available, you will see the following message: Otherwise you will see the following message (See Update Required for more information): 3. You will then be instructed to turn the key OFF, Press and turn the key back to ON (do not start) to begin saving STOCK: Evolution FORD Power Stroke 7.3 Liter 15 During the storing process, you will see the following display:
Evolution FORD Power Stroke 7.3 Liter 16 4. If this is the first time the unit is used on a particular vehicle, the Evolution will build and verify the modified calibrations (Skip to step 5 for subsequent programming operations). During this process, you will see the following displays

Related Content:

1997 ford ranger 2 3 repair manual torrent, 2008 gmc acadia water pump removal instructions, edge programmer locked?, ford 2004 f350 moonroof troubleshoot, proramming power window switch on 09 tahoe without programmer, replace water pump on 2008 gmc acadia

2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI – Removal and Installation Manual

0

Filed Under (Toyota Manuals) by admin on 26-02-2012

download
REMOVAL 1. REMOVE HOOD Torque: 13 Nm (130 kgf-cm, 9 ft. lbs.) 2. REMOVE BATTERY 3. REMOVE ECM AND ECM CASE Torque: 6.9 Nm (70 kgf-cm, 61 inch lbs.) 4. REMOVE ECM BRACKET Torque: Bolt: 18 Nm (185 kgf-cm, 13 ft. lbs.) Nut: 12 Nm (120 kgf-cm, 9 ft. lbs.) 5. REMOVE AIR CLEANER ASSEMBLY 6. REMOVE NO.2 CYLINDER HEAD COVER Torque: 7.0 Nm (71 kgf-cm, 62 inch lbs. 7. REMOVE 2 GROUND CABLES Torque: 18 Nm (185 kgf-cm, 13 ft. lbs.) 8. DISCONNECT CONTROL CABLE FROM CLAMP 9. DISCONNECT INPUT TURBINE SPEED SENSOR CONNECTOR 10. DISCONNECT COUNTER GEAR SPEED SENSOR CONNECTOR 11. REMOVE VEHICLE SPEED SENSOR CONNECTOR 12. REMOVE 2 UPPER SIDE TRANSAXLE MOUNTING BOLTS FROM TRANSAXLE Torque: 64 Nm (650 kgf- cm, 47 ft. lbs.) 13. DISCONNECT SOLENOID CONNECTOR AND PARK/NEUTRAL POSITION SWITCH CONNECTOR Disconnect the solenoid connector and park/neutral position switch connector. 14. DISCONNECT CONTROL CABLE 15. REMOVE BOLT AND DISCONNECT RADIATOR RESERVOIR Torque: 4.9 Nm (50 kgf-cm, 43 inch lbs.) 16. REMOVE STARTER 17. REMOVE LH, RH, CENTER ENGINE UNDER COVERS 18. DRAIN ATF FROM FRONT DIFFERENTIAL CASE Torque: 54 Nm (550 kgf-cm, 40 ft. lbs.) 19. REMOVE LH AND RH DRIVE SHAFTS.

Related Content:

is there a recall on the ecm on a 2000 toyota celica gt

Related Content:

99 hyundai ecm fuse location, hino dutro vnt circuit open, 2002 Ford Windstar Repair Manual, 2002 saturn vue repair manual free, 2002 taurus ecm removal, Free 2002 BMW Service Manual, saturn 2002 l300 maf volts, 2002 vw passat repair manual, 2001 pontiac sunfire P0502, 2000 saturn l300 ecm replacement