Skip to content

how to put a 2000 chrysler lhs 3 5 engine top dead center

You search PDF repair manual about how to put a 2000 chrysler lhs 3 5 engine top dead center, if there are search results will appear below. If search results do not exist, please search by others keyword.

2000 Audi A6 OIL PAN (A4 And A6) Removal And Installation Manual

download
OIL PAN(A4 & A6) Removal (Lower Pan- A4 & A6) 1. Disconnect negative battery cable. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Unbolt left and right swaybar stabilizer bracket bolts (4) from mounting bracket. See Fig. 98 . Lower swaybar stabilizer not more than 10cm (3.94 INCHES) and secure with heavy wire. 4. If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) bracket from right side oil pan. 5. Remove lower oil pan. To install oil pan (lower), see INSTALLATION (LOWER OIL PAN- A4 & A6) . Installation (Lower Oil Pan- A4 & A6) 1. Ensure oil pan surfaces are clean and dry. Remove residual sealant from oil pan, if necessary, with hand drill and plastic brush instead of a flat scrapper. See Fig. 99 . Install gasket. 2. Install 2 bolts diagonal to each other (to hold up pan). Install the rest of the bolts and hand tighten. 3. Starting at center and moving outward, tighten lower oil pan to upper oil pan bolts to 10 N.m (89 INCH lbs.). Tighten oil pan drain plug 30 N.m (22 ft. lbs.). Wait 30 minutes before filling with engine oil. Tighten all bolts to specification. See TORQUE SPECIFICATIONS . 4. To complete installation, reverse removal procedure. Fill and bleed cooling system. See COOLING SYSTEM BLEEDING . Removal (Upper Oil Pan- A4 & A6) 1. Disconnect negative battery cable. Remove oil dipstick. Unbolt oil dipstick tube at front of cylinder head. Remove oil dipstick tube. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Move lock carrier into service position. See LOCK CARRIER . This will allow servicing of front engine components and facilitate removal of oil pan. 4. Open coolant expansion tank cap, drain cooling system at radiator. Open the coolant pump bearing housing drain plug. Located at bottom of block near transmission bell housing, drivers side of vehicle. See Fig. 32 – Fig. 33 . If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) CAUTION: Wear eye protection NOTE: Obtain radio code before disconnecting battery. For help in identifying components and component locations, refer to illustrations Fig. 108 -Fig. 109 . NOTE: If engine is out of car, ensure oil pan is aligned with cylinder block on flywheel side. 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve bracket from right side oil pan. 5. Position Engine Support (10-222A) with (10-222A/3) engine support adapter, or equivalent, on bolted flanges of fenders. Connect support bracket to front and rear engine lifting eyes. Lift up engine as far as possible. DO NOT use excessive force to raise engine. 6. Cut tie wraps and open bracket supporting starter wiring. See Fig. 97 . Disconnect electrical connection at starter.

2000 Dodge Dakota & Durango Power Windows ADJUSTMENTS

download
ADJUSTMENTS WINDOWS Remove door trim panel. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. Loosen bolts holding window to regulator. Raise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Distribution Center (PDC). PDC is located in left front corner of engine compartment. Inspect power window system ground circuit. See WIRING DIAGRAMS . SYSTEM TESTS ALL WINDOWS INOPERATIVE Dakota 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Check for continuity between ground and terminal No. 3 (Black wire) at driver power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver power window 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango 2000 Dodge Durango 2000 ACCESSORIES & EQUIPMENT’ ‘Power Windows – Dakota & Durango switch connector and ground. See WIRING DIAGRAMS . 3. Connect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 5 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. Durango 1. Check circuit breaker for power window system. See TROUBLE SHOOTING . Replace circuit breaker as necessary. If circuit breaker is okay, go to next step. 2. Disconnect negative battery cable. Remove driver’s front power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. 3. Check for continuity between ground and terminal No. 5 (Black wire) at driver’s power window switch wiring harness connector. If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between driver’s power window switch connector and ground. See WIRING DIAGRAMS . 4. Reconnect negative battery cable. Turn ignition on. Measure voltage between ground and terminal No. 4 (Tan wire) at driver’s power window switch wiring harness connector. If battery voltage is present, check driver’s power window switch. See POWER WINDOW SWITCH under COMPONENT TESTS. If battery voltage is not present, repair open Tan wire between driver power window switch connector and ignition switch. See WIRING DIAGRAMS . See POWER DISTRIBUTION article in WIRING DIAGRAMS. ONE WINDOW INOPERATIVE

2005-2006 (LX) Chrysler 300/ Magnum/ Charger/ Pacifica Multiple Cylinder Misfire Or Rough Idle Repair Manual

download
REPAIR PROCEDURE: VALVE ROTATION: 1. Relieve the fuel pressure. Refer to the detailed service information available in TechCONNECTunder: Service Info>14-Fuel System>Fuel Delivery >Standard Procedure>Fuel System Pressure Release Procedure. 2. Remove upper intake manifold. Refer to the detailed service information available in TechCONNECTunder: Service Info >9-Engine>Manifolds>Intake Manifold> Removal. 3. Remove cylinder head cover(s). Refer to the detailed service information available in TechCONNECTunder: Service Info >9-Engine>Cylinder Head>Cylinder Head Cover(s) >Removal. 4. Remove rocker arm and shaft assembly. Refer to the detailed service information available in TechCONNECT under: Service Info >9-Engine>Cylinder Head> Rocker Arm/Adjuster Assembly >Removal). 5. Clean and mark the tip of each exhaust valve stem at the 12 O’clock position witha paint marker. The paint mark will be used later to assist with determining the amount of valve rotation. 6. Remove the sparkplugs. 7. Rotate the crankshaft clockwise, until the number 1 piston is at Top Dead Center (TDC) on the compression stroke. 8. Install the compression tester sparkplug adapter in cylinder#1 sparkplug hole. With air hose attached to sparkplug adapter, apply 620.5 to 689 kPa (90 to 100 psi) air pressure. This is to hold valves into place while servicing components. 9. Using Tool MD 998772A (1) with adapter 6527 (4) or equivalent, slightly compress the exhaust valve spring to release tension against the valve and valve spring retainer ( Fig. 1 ). 10. Remove the valve spring retainer locks and discard the locks. NOTE: It is important that the valve rotation section of this repair procedure be performed.

2000 Cadillac Catera Timing Belt Service and Repair Manual

download
Timing Belt Replacement TIMING BELT REPLACEMENT Removal Procedure ^ Tools Required -J 42069 Timing Belt Alignment Kit -J 42098 Crank Hub Torx Socket Notice: Failure to follow the described timing belt inspection and maintenance may result in a broken timing belt and cause severe engine damage. 1.Inspect the cold start counter (also called a heavy duty register) with a scan tool. If there are any cold starts (below -28° C or -20° F) visually inspect the timing belt for cracks. It cracks are noted, do not reuse the belt. Replace the belt and clear the cold start counter. If the belt is okay, and is reused, do not clear the cold start counter. 2.Remove the intake air resonator. Refer to Intake Air Resonator Replacement in Powertrain Management. 3.Remove the intake plenum. Refer to Intake Plenum Replacement. 4.Remove the timing belt cover. Refer to Timing Belt Cover Replacement. 5.Remove the crankshaft balancer bolts. 6.Remove the crankshaft balancer from the crankshaft sprocket. 7.Rotate the crankshaft clockwise to 60 degrees Before Top Dead Center (BTDC) 8.Install the J 42069-10 to the crankshaft sprocket with the knurled bolt. 9.Use the J 42098 to carefully turn the crankshaft in the engine rotational direction (clockwise) until the lever of the J 42069-10 firmly contacts the water pump pulley flange. 10.Secure the moveable lever of the tool to the water pump pulley flange. Important: Ensure that the crankshaft is not 180 degrees off TDC. The reference marks on the camshaft gears should be aligned with the corresponding notches on the rear timing belt cover at this point. If they are not aligned, the engine is 180 degrees off. 11.Install the J 42069-1 and the J 42069-2 to the camshaft gears. If the J 42069-1 or the J 42069-2 do not fit into the teeth of the camshaft gears, it may be necessary to loosen the relevant timing belt idler pulley and turn the cam until the J 42069-1 or the J 42069-2 can be inserted. Notice: After timing belt is removed, never turn camshaft and crankshaft independently. If turned, interference may occur among pistons and valves, and parts related to pistons and valves may be damaged. 12.Loosen the timing belt tensioner and idler pulleys. Important: Do not remove J 42069-1 and the J 42069-2 while the belt is removed. 13.Remove the timing belt. Installation and Initial Adjustment Procedure ^ Tools Required -J 42069 Timing Belt Alignment Kit -J 42098 Crank Hub Torx Socket

2001 Honda Prelude Engine, Cooling and Exhaust Engine Timing Belt Service and Repair Manual

download
Removal and Installation REMOVAL NOTE: * Turn the crankshaft pulley so the No. 1 piston is at Top Dead Center (TDC) before removing the belt. * Inspect the water pump after removing the timing belt. * Replace the timing belt and timing balancer belt at 105,000 miles (168,000 km) according to the maintenance schedule (normal conditions/severe conditions). If the vehicle is regularly driven in one or more of the following conditions, replace the timing belt and timing balancer belt at 60,000 miles (U.S.A.) 100,000 km (Canada). * In very high temperatures (over 110°F, 43°C). * In very low temperatures (under -20°F, -29°C). 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the radio’s preset buttons. 2. Disconnect the battery negative terminal first, then the positive terminal. 3. Remove the wheel well splash shield. 4. Loosen the adjusting bolt, locknut and mounting bolt, then remove the Power Steering (P/S) pump belt. 5. Remove the alternator terminal and connector. 6. Loosen the adjusting bolt, mounting bolt and lock nut, then remove the alternator belt. 7. Remove the side engine mount. NOTE: * Support the engine with a jack before removing the side engine mount and upper bracket assembly is removed. * Make sure to place a cushion between the oil pan and the jack 8. Remove the dipstick and the tube. 9. Remove the cylinder head cover. NOTE: The procedures in steps 10 and 11 are for reusing the timing belt. For replacing the timing belt, skip these procedures and go to step 12. 10. Use an open-end wrench to loosen the maintenance bolt. If it cannot be loosened with an open-end wrench, a box wrench can be used after removing the lock pin. NOTE: Use of a tool should be limited to initial loosening only 11. Unscrew the maintenance bolt by hand until it stops. The auto-tensioner bracket is now fixed. NOTE: * Never use a tool to unscrew the maintenance bolt after initial loosening it. * If the auto-tensioner has been extended and the timing belt cannot be installed, remove the auto-tensioner, compress it and reinstall it. 12. Remove the middle cover. NOTE: Do not use the middle cover to store removed items. 13. Remove the pulley bolt and crankshaft pulley