Skip to content

how to remove 2001 buick engine

You search PDF repair manual about how to remove 2001 buick engine, if there are search results will appear below. If search results do not exist, please search by others keyword.

Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination)

download
2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue 1. Verify that the coolant is at proper level in the radiator and the coolant recovery bottle. If the coolant is low, add proper amount of 50/50 water and DEX-COOL® mixture. If the low coolant light operates properly, diagnose the cooling system for loss of coolant as outlined in SI. DO NOT proceed further with this bulletin. 2. Remove the low coolant level sensor. Refer to Coolant Level Module Replacement in the Engine Cooling sub-section. 3. With the key on, the engine off and the coolant level sensor disconnected from the vehicle wiring harness, observe the low coolant light: Subject: Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination) Models: 2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue • Light is on — Chassis wiring or instrument cluster concern. Follow the appropriate diagnostic information in SI. • 4. With the key off, connect the coolant level sensor into the vehicle’s wiring harness. Connect a ground wire (1) to the battery negative terminal. Using a sharp probe (3) attached to the ground wire, ground the coolant sensor probe (2) as shown in the illustration. Make sure a good contact is made. With the key on and the engine off, observe the low coolant light for at least 15 seconds. 5. Using a small wire brush or emery cloth, polish the low coolant level sensor probe to remove any film or oxidation. The probe should be a bright brass color when finished. Use Brake Parts Cleaner to flush removed deposits from the low coolant sensor probe. Reinstall the low coolant sensor into the vehicle and proceed to Step 6. 6. Flush the cooling system and install new DEX-COOL® mixture as outlined in the SI. Check the vehicle’s warranty history to determine if any engine gasket had recently been changed. If there has not been a recent gasket replacement, locate and repair the source of the engine oil contamination

1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

1999 Saturn SL1 L4-1.9L SOHC VIN 8 Engine – Driveability Concerns/ Cooling System DTC’s Set

download
1. Disconnect engine coolant temperature sensor electrical connector and inspect sensor and connector terminals for corrosion and/or evidence of engine coolant. ^If terminals are corroded or if there is evidence of engine coolant proceed to step 4. ^If terminals are not corroded and there is no evidence of engine coolant, reconnect the electrical connector and continue to next step. 2. Perform one or both of the following checks to determine whether the engine coolant temperature sensor is providing the correct temperature indication. If engine coolant temperature sensor reading does not pass either of the above tests, continue with next step. ^If engine is at ambient temperature (vehicle has been sitting overnight or not started for several hours), use a Scan tool to compare the inlet air temperature ( IAT ) to the engine coolant temperature ( ECT ). These two readings should be within 2°C (4°F) of each other. ^If engine is at operating temperature, install a thermometer in the coolant recovery reservoir. With the engine running and A/C off, use a Scan tool to compare the engine coolant temperature sensor reading to the thermometer reading. These two readings should be within 8°C (15°F) of each other If engine coolant temperature sensor reading passes both of the tests above, refer to appropriate symptom diagnostic chart in the Engine/Emissions Controls Section of applicable Engine Service Manual. 3. Turn ignition off. 4Remove coolant surge tank cap. 5. Drain at least 1.9 L (2 Qt.) of engine coolant from the cooling system by opening radiator drain valve or removing engine drain plug. Collect engine coolant in a container. 6. Disconnect engine coolant temperature sensor electrical connector. 7. Remove engine coolant temperature sensor from cylinder head. 8. Obtain replacement engine coolant temperature sensor (P/N 21025106). 9. Use appropriate tap to clean sensor mounting hole of any thread sealant residue. 10. Install engine coolant temperature sensor in cylinder head. Torque: Engine Coolant Temperature Sensor: 8 Nm (71 in-lbs) 11. Inspect harness connector terminals for corrosion and/or evidence of engine coolant. If harness connector terminals are corroded or there is evidence of engine coolant, the harness connector must be replaced with new connector (P/N 12117087-includes: connector, terminals, wires, and splice sleeves). 12. Connect engine coolant temperature sensor connector. 13. Transfer engine coolant drained in step 5 into coolant surge tank. If necessary fill coolant surge tank to the FULL COLD range with 50/50 solution of correct type of antifreeze and clean water. 14. Start engine and check for leaks. 15. Run engine until upper radiator hose is hot, then add additional coolant if needed to bring the level to the FULL COLD level (1991-early 1997) or within the Min./Max. cold range (late l997-2001). 16. Install coolant surge tank cap.

1996-2001 Honda Civic – ALL Civic Rear Main Oil Seal Leaks Repair manual

download
REPAIR PROCEDURE 1. Remove the transmission. Refer to section 13 or 14 of the appropriate service manual. 2. Remove and discard the rear main oil seal (crankshaft oil seal). 3. Install the new oil seal. Refer to page 7 – 29 of the ’96-00 service manual or page 7-27 of the ’01 service manual. 4. Reinstall the transmission. 5. Reinstall the drain plug with a new sealing washer. 6. Refill the transmission with the appropriate fluid. 7. 2001 models only. Do the idle learn procedure: Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are turned off, then start the engine. Let the engine warm up to its normal operating temperature (the cooling fan cycles twice). Let the engine idle (throttle fully closed with all electrical items turned off) for 10 minutes. 8. 2001 2-door EX and LX models only. Drive the vehicle above 40 mph for 5 to 10 minutes with the cruise control on. (This lets the cruise control actuator learn how much slack there is in the throttle cable.)

2001-2008 GM 1500/2500 Series Pick-Up Edelbrock Header Installation Manual

download
INSTALLATION INSTRUCTIONS DISASSEMBLY 1. Disconnect negative battery cable. 2. Unbolt exhaust pipes from manifolds. RIGHT SIDE 1. Disconnect and remove spark plug wires. 2. Unbolt and remove dipstick tube. 3. Unbolt and remove manifold from top. 4. Install flange gasket and header from top. Install header bolts, lock washers, and thick flat washers supplied. Note: Ensure proper alignment on slotted holes of port flange and only snug bolts at this time. 5. Re-install spark plug wires. 6. Re-install dipstick tube. 7. Some models may require the aluminum heat shield under the A/C receiver dryer to be re-positioned, adjusted or bent to gain some clearance between header and heat shield. LEFT SIDE 1. Disconnect and remove spark plug wires. 2. Unbolt and remove manifold. 3. Install flange gasket and header from top. Install header bolts, lock washers, and thick flat washers supplied, ensure proper alignment and only snug bolts at this time. IMPORTANT NOTE: Proper installation is the responsibility of the installer. Improper installation will void warranty and may result in poor performance and engine or vehicle damage.
©2007 Edelbrock Corporation Catalog #65022 & 65023 Page 2of 2 Brochure #63-0364 Rev. 8/07 – DA/mc Edelbrock Corporation, 2700 California St., Torrance, CA 90503 Tech Line: 1-800-416-8628 Office: 310-781-2222 Tech Fax: 310-972-2730 E-Mail: Edelbrock@Edelbrock.com 2. Using supplied hardware, re-attach the factory exhaust pipes to the headers and tighten bolts evenly to ensure a tight seal. ( Note: The 7/16 x 2 bolts are to be used on 4.8L, 5.3L, & some 6.0L V8s. The 7/16 x 1 ¾ are for the left side of 4.8L & 5.3L V8s, and on the 6.0L V8 that do not have OEdonut gaskets. 3. After the factory exhaust pipes have been tightened to the collector flange of the header, tighten the port flange bolts to recommended factoryspecifications. FINAL INSPECTION 1. Check all lines (hydraulic, vacuum, air conditioning and fuel) to ensure there is adequate clearance to headers. 2. Re-connect battery. 3. At this point, it is a good idea to look everything over and make sure that nothing was missed in assembly. 4. Start vehicle and bring up to normal operating temperature. Check for possible leaks. 5. Turn engine off and let cool. Tighten all bolts again. Note: Thick washers are to be used on slotted holes of port flange. 4. Re-install spark plug wires. Note: Due to production tolerance, it may be necessary to bend the motor mount heat shield for better clearance. ASSEMBLY OF EXHAUST PIPE Note: Some 2007 model year vehicles will have a donut gasket on the right side OE exhaust manifold. If your vehicle has that donut gasket, it will be re-used with your shorty headers (see below). This system comes with 2 exhaust crush rings. On 2001- 2006 4.8L & 5.3L V8s, one will be used on the left side collector. On 2001-2006 6.0L vehicles will use one on the left side and one on the right side to replace factory-installed crush rings. 1. On 4.8L, 5.3L, &6.0L V8s with donut gasket – Remove the donut gasket from right side exhaust manifold. Using a pair of pliers, remove the retaining ring from the donut gasket and place the donut gasket in flare of factory exhaust pipe.