Skip to content

how to remove 2004 buick park ave automatic climate control unit

You search PDF repair manual about how to remove 2004 buick park ave automatic climate control unit, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Buick LeSabre Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Service Manual

download
Correction 1. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary: 2. Set the tire pressure to 30 psi (205 kPa) COLD. Subject: Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) • Missing balance weights • Bent rim flange • Irregular tire wear • Incomplete bead seating • Tire irregularities • Mud/ice build-up in wheel • Stones in the tire tread © 2009 General Motors Corporation. All rights reserved 3. Road test the vehicle with the Electronic Vibration Analyzer (EVA) essential tool for a sufficient distance on a known, smooth road surface to duplicate the condition. Record the Hertz (Hz) reading as displayed by the EVA onto the tire data worksheet found at the end of this bulletin. This should be done after a tire break-in period of at least 10 miles (16 km) at 45 mph (72 km/h) or greater, in order to eliminate any possible tire flat-spotting. 4. If the road test indicates a shake/vibration still exists, check the imbalance of each tire/wheel assembly on a known, calibrated, off-car dynamic balancer. If any assembly calls for more than ¼ ounce on either rim flange, remove all balance weights and rebalance to as close to zero as possible. Important: Some GM dealers may have a Hunter GSP9700 Road Force Balancer, or a Coats XR1850 Runout Balancer. Either will simplify Step 5 by not requiring dial indicators. If a Hunter GSP9700 machine is available, it may also be used to measure the radial force of the tire/wheel assembly. A guideline here is 18 lbs or less. 5. While on the balancer, measure wheel runout. If radial or lateral runout exceeds .020 in (0.50 mm) for aluminum wheels (.030 in (0.76 mm) for steel wheels), replace the wheel. 6. After confirming wheel balance and wheel runout, if any changes were made, road test the vehicle again. 7. If the smooth road shake/vibration still exists: Important: THE CONTROL ARMS SHOULD ONLY BE INSTALLED ON VEHICLES IF, AFTER THE TIRE AND WHEEL DIAGNOSIS AND REPAIRS HAVE BEEN PERFORMED, THE VIBRATION CONDITION STILL EXISTS. 8. Replace both lower control arms on vehicles built prior to the following VIN breakpoints. On Aurora, Bonneville, DeVille, Park Avenue, Park Avenue Ultra and Seville models, a newly developed hydro-bushing lower control arm with improved damping characteristics has been released. This control arm is not used on the LeSabre. The new lower control arms may provide an incremental improvement to the vehicle ride. Customers who have become “tuned in” to the shake condition may still feel some shake in the vehicle after the new lower control arms are installed. Refer to Lower Control Arm Replacement in SI (refer to the Parts Information table below for SI document ID numbers) . Important: The completed worksheet must be attached to the hard copy of the repair order. • If a Hunter GSP9700 Road Force/Balancing machine is used, record radial force variation (RFV) on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies read more than 18 lbs, match mount the tire to the wheel to get below 18 lbs. Readings of 12 lbs or less are preferable for sensitive customers. • If a Coats XR1850 Runout/Balancing Machine is used, record radial runout of the tire/wheel assemblies on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies are more than .040, match mount the tire to the wheel to get below .040. Readings of .030 inch or less are preferable for sensitive customers. • If the RFV or runout cannot be reduced to an acceptable level, replace the affected tire(s) under the guidelines of the GM Tire Warranty. • The screened tire program is only available for the General branded tires used on the Buick LeSabre. Complete the tire request form at the end of this bulletin and fax to Continental/General. • Road test the vehicle to ensure the shake/vibration has been eliminated

1996-1998 TOYOTA 4RUNNER w/o auto climate control INSTALLATION INSTRUCTIONS

download
STEP1. Begin by removing four (4) knobs on the climate control levers by grasping knobs and pulling toward you to slide the knobs off. NOTE: On 1998 models there are two (2) sliderand two (2) dial type knobs. Grasp knobs and pull toward you to remove. Set knobs aside. Insert hook tool behind face plate on climate control panel in the top left corner. Carefully pull toward you to release clip. Repeat on remaining three (3) corners to release corner clips. Set aside. Remove radio trim bezel. STEP2. Locate and remove two (2) Phillips screws [one (1) on right and one (1) on left of the climate control unit] that hold the radio trim bezel in place. Set screws aside. Insert the hook tool between the bezel and dash in the upper right hand corner above the air vent. Pull toward you to release corner clip. Do the same in the upper left corner. Grasp the bezel and work loose the remaining clips. Push the bezel to the left side just enough to get at the top right screw that holds the radio in place. Remove this screw with your #2 Phillips screwdriver. Set screw aside. STEP3. Attach the phone holder onto the Pro.Fit VSMTM . Insert screw in top hole of Pro.Fit VSMTM . Align Pro.Fit VSMTM with screw hole above centering pin and insert and tighten factory screw. Re-assemble dash in reverse order securing all screws and clips. This completes the installation

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

2004 Toyota Avensis Installation Manual

download
Remove the dashboardpanels around the radio at the location of the ar- rows. 12 3 45 6 Remove the original OEM metal brackets from the radio and the climate control unit. This is tigten by twelve screws. Remove the original radio from the climate control. Slide the climate control unit to the right. Place the new metal bracket and the climate control unit between the OEM radio brackets.Tighten the climate control with the four original screws. 78 9 Place the OEM replacement panel on the climate control unit by sliding it to the left . Place the OEM replacement panel with the climate control unit and the metal bracket into the dashboard. Place the new headunit. 10 11 Place the radio trim and replace all dashboardpanels in reverse order. Remove the frame above the radio by using a plastic wedge at the location of the arrows. Remove the original radio at the location of the arrows. The radio is tighten by four screws. * Mount the plates. We advice to use the following positions. Other positions are also possible. Use position 1 marked with a cross. Use position 14 & 16 marked with an arrow. Measured from left to right. We advice to use the following positions. Other positions are also possible. Use position 1 marked with a cross. Use position 12 & 14 marked with an arrow Measured from left to right. Installation kit includes the following items: * 1X 2-ISO 100 mm. metal bracket * 1X Radio trim * 2X Mounting plates * 2X Mounting spacers * 4X Screws * 2X Radio keys You need OEM Bezel Part Number : 55405-12A00 metal bronze 55405-02130 black 2-DIN BKX-1300-06 Installation manual for: Toyota Auris Installation kit includes the following items: * 1X 2-ISO 100 mm. metal bracket * 1x Replacement panel for non motorized screen * 2X Replacement panel for motorized screen * 2X Mounting plates * 2X Mounting spaces * 2X Radio keys * 4X Screws Use this hole Use this hole EXAMPLE Remark: The fi xing position can be different between Audio and Multimedia unit