Skip to content

how to remove a 2008 toyota highlander rear tail light assembly

You search PDF repair manual about how to remove a 2008 toyota highlander rear tail light assembly, if there are search results will appear below. If search results do not exist, please search by others keyword.

2007-2008 Toyota Tundra Rear Driveshaft/ Propeller Shaft Clunk/ Thunk Noise Repair Manual

download
Repair Procedure 1. Confirm that the condition is the rear driveshaft clunk/thunk noise. A. Test drive the vehicle and confirm the customer’scomplaint. B. Place the transfer casein 4WDHighwiththe center differential lock ed. Remove the rear driveshaft and test drive the vehicle. Refer to the Technical Information System (TIS), 2007 or 2008 model year Tundra Repair Manual, Drivetrain -Driveshaft/Propeller Shaft-”Propeller Shaft: Propeller Shaft Assembly (for 4WD): Removal” C. Is the clunk/thunk noise eliminated when coming to a stop and/or when accelerating froma stop? •If Yes-Replace rear driveshaft (propeller shaft assembly). Go to Step 2. •If No-This TSB does NOT apply. Continue diagnosis to isolate cause of condition Repair Procedure (Continued) 2. Install the NEW driveshaft (propeller shaft) assembly. Refer to TSB DL 001-07 for the installation method for 3 joint driveshaftassemb lies on 2007 model year Tundra. Refer to TIS, 2007 or 2008 model year Tundra Repair Manual, Drivetrain -Driveshaft/Propeller Shaft-”Propeller Shaft: Propeller Shaft Assembly (for 4WD): Installation” NOTE Re-usethespacers provided under the center support bearing to ensure the proper alignment of the center support bearing. 3. Test drive and confirm that NO abnormal vibrations or shudders occur while driving, and that the driveshaft clunk/thunk noise is eliminated.

2008 TOYOTA HIGHLANDER TRAILER WIRE HARNESS Preparation

download
1. Supplemental Restraint System (SRS) (a) Failure to carry out procedures listed below could result in possible deployment of airbag, personal injury, or unnecessary repairs to SRS. (b) Turn the key switch to the LOCK position. (Fig. 1-1) (c) Remove the key from the ignition switch. (d) Disconnect the negative battery cable. (Fig. 1-2) (e) Never use a voltmeter to troubleshoot any of the harnesses or connectors to the SRS. Accidentally probing the connectors to the SRS can lead to deployment of the airbag. (Fig. 1-3) (f) SRS wire harness loom/cover is bright yellow in color. Fig. 1-1 Fig. 1-2 Fig. 1-3 10 mm socket
TOYOTA HIGHLANDER 2008 – TRAILER WIRE HARNESS Procedure Page 5 of 16 pages Issue: A 04/13/07 2. Wiring Precautions (a) DO NOT pull on vehicle wires and/or wire harness. To uncouple electrical connectors, pull only on the connector. (Fig. 2-1) (b) Use nylon ties and adhesive foam strips to secure the vehicle harness and the trailer wire harness. (c) Ensure that all wires are properly insulated from ground. (d) When installing the trailer wire harness, make sure it is not cut or perforated by any sharp metal objects. 3. General Practices and Procedures (a) Before starting installation, refer to the supplemental restraint system procedures in Section 1 above. (b) Take care not to scratch any part of the vehicle. Bind the tips of tools (clip remover, slot screw driver, etc.) with vinyl tape to prevent damage to any part of the car, or use a nylon removal tool (resin based prying tool). (Fig. 3-1) (c) Use a small parts container to store removed bolts and tapping screws so that they can be reassembled correctly. (d) Ensure that seat/floor protectors are in position. (e) After fastening plastic ties, clip away all the excess of the ties using diagonal pliers. (Fig. 3-2)

Toyota Hybrid Highlander Rear View Camera Installation Manual

download
Remove the cap and the bolt holding the upper left side, rear seat belt holder and pull the panel partially free. Remove the push clips visible on the edge of the headliner and pull down the edge of the headliner so that you can begin routing your cables. Bring the camera wire from your harness around to the larger rubber boot connecting the hatch wiring to the interior of the car. Manipulate the camera connector up through this rubber boot. Take your time : ) Once through, make your connection to the cable from the license plate camera to complete this phase. Route your cable down the left side and out near the area behind the tail light. This is where we will make the connections for camera power and ground. The wiring harness for your camera contains connectors and wire taps so that no wires will need to be cut during installation. The wire taps are designed to simply fold around a wire, and when squeezed together with a pair of pliers, create a convenient connection for your harness wires to plug into. Locate the wires behind the clear reverse tail light. Place wire taps on both wires of its connector ( PINK and WHITE W/BLACK STRIPE ) Plug the wires from the camera harness into the appropriate wire tap. The GROUND wire from your camera harness pugs into the WHITE W/BLACK STRIPE wire and the 12V/REVERSE wires are both plugged into taps on the PINK wire. You may find it more convenient to place a tap on one of the power wires of the camera harness to connect them both together, and then place a single tap on the PINK wire to make your connection to. The additional lengths of camera harness wiring may be stored inside this panel area. Next, the video cable from the camera is routed to the front of the vehicle. This is accomplished by lifting out the rear cup holder and pulling the cable up and through to the front of the vehicle. There is a bolt on the front of the cup holder panel and then it can be lifted out. Tuck the wire under the edge of the trim panels along the doors as you bring the video cable up to the front of the car. The trim panel should be pulled up at the driver area to allow the kickpanel up front to be pulled free. Again, no screws are holding these panels in place and are simply pulled free with your fingertips.

2004 Toyota Sienna POWER SLIDING DOOR INOPERATIVE Repair Manual

download
Remove Slide Door Window Garnish. A. Fully open the slide door window. B. Remove the glass run. C. Using a screwdriver, disengage the clip and remove the garnish. HINT: Tape the screwdriver tip before use. D. Using the taped screwdriver, disengage the 2 claws and remove the inner weatherstrip from the garnish. Parts Information Repair Procedure Clip POWER SLIDING DOOR INOPERATIVE – EL004-04 April 19, 2004 Page 3 of 7 2. Remove Side Trim Board Cover Rear. A. Remove the 2 screws. B. Using the taped screwdriver, disengage the 8 claws and remove the cover together with the window control switch. C. Remove the 2 screws and window control switch. 3. Remove Rear Door Trim Board Sub-assembly. A. Remove the screw. B. Using the taped screwdriver, disengage the 9 clips and remove the trim board. HINT: In order to prevent the door panel from being damaged, cover the areas with protective tape as indicated by the arrows in the illustration. 4. Remove Rail End Molding. A. Open the quarter glass. B. Using the taped screwdriver, disengage the clip and 2 claws, and remove the rail end molding. Repair Procedure (Continued) : Claw 1 2 3 4 5 5 4 3 2 1 Protective Tape Protective Tape : Clip : Clip : Claw POWER SLIDING DOOR INOPERATIVE – EL004-04 April 19, 2004 Page 4 of 7 5. Remove Center Bracket No. 2. A. Remove the 2 bolts and Center Bracket No. 2 together with the tensioner (color: white). B. Remove the tensioner from Center Bracket No. 2. 6. Remove Center Bracket No. 1. A. Remove the 2 bolts and Center Bracket No. 1 together with the tensioner (color: black). B. Remove the tensioner from Center Bracket No. 1. 7. Remove Slide Door Window Assembly LH. A. With Sunshade: Remove the sun shade hook. B. Remove the bolt and window frame. C. Remove the bolt. D. Loosen the nut. E. Push the rear lower window frame in the direction indicated by the arrow in the illustration

1990 Toyota Supra Factory Repair Manual

download
REMOVAL AND INSTALLATION OF TRANSMISSION Removal of Transmission REMOVE NEGATIVE BATTERY CABLE CAUTION: Work must be started after approx. 20 se- conds or longer from the “LOCK” position and the nega- tive (-) terminal cable is disconnected from the battery. REMOVE CENTER CLUSTER FINISH PANEL REMOVE SHIFT LEVER FROM INSIDE OF VEHICLE RAISE VEHICLE AND DRAIN TRANSMISSION OIL NOTICE: Be sure the vehicle is securely supported. REMOVE PROPELLER SHAFT Remove the propeller shaft and insert SST into the extension housing. SST 09325-2001 0 (for W58 M/T) 09325-4001 0 (for R 1 54 MIT) DISCONNECT EXHAUST FRONT PlPE FROM TAIL PlPE (a) Remove the rubber hanger. (b) Disconnect the pipe at the front side of the converter. (R154 M/T) REMOVE EXHAUST FRONT PlPE (a) Disconnect the exhaust pipe bracket from the clutch housing. (b) Remove the nuts and exhaust pipe from the exhaust manifold. DISCONNECT SPEEDOMETER CABLE DISCONNECT BACK-UP LIGHT SWITCH CONNECTOR AND REAR SPEED SENSOR CONNECTOR (wl A.B.S.) MANUAL TRANSMISSION – Removal and Installation of Transmission MT-5 10. REMOVE CLUTCH RELEASE CYLINDER 11. REMOVE STARTER Remove the mounting bolts and lay the starter alongside the engine. 12. JACK UP TRANSMISSION SLIGHTLY Raise the transmission enough to remove the weight from the rear support. 13. REMOVE ENGINE REAR MOUNTING 14. REMOVE TRANSMISSION MOUNTING BOLTS AND FLYWHEEL HOUSING UNDER COVER 15.-1 (W58 M/T) REMOVE TRANSMISSION ASSEMBLY Pull out the transmission down and toward the rear. 15.-2 (R154 M/T) REMOVE TRANSMISSION ASSEMBLY WITH CLUTCH COVER AND DISC (a) Remove the two clutch housing covers. (b) Pull out the release fork through the left clutch housing hole. (c) Place the matchmarks on the clutch cover and flywheel. (d) Remove the clutch cover set bolts while turning the crankshaft pulley. HINT: Loosen each set bolt one turn at a time until spring tension is released. (e) Remove the clutch cover and disc from the flywheel, and fully move them toward the transmission. (f) Pull out the transmission with the clutch cover and disc.