how to remove axle shaft seal in 04 f250

You search PDF repair manual about how to remove axle shaft seal in 04 f250, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to remove axle shaft seal in 04 f250 Direct Download speed 5432 Kb/s

  how to remove axle shaft seal in 04 f250 Full Version speed 8172 Kb/s



1997 Jeep Grand Cherokee Laredo 7 1/8″, 7 1/3″, 7 9/16″, 7 4/5″, 8 1/4″, 8 1/2″ & 8 9/10″ Ring Gears Removal And Installation Manual

0

Filed Under (Jeep Manuals) by admin on 04-07-2012

download
Removal (Model 194, 8 1/4″ & 1998 Grand Cherokee 216 Axles) 1. Raise and support vehicle. Remove rear wheel(s). If equipped with drum brakes, remove brake drum. If equipped with disc brakes, remove brake caliper and rotor. On all models, clean axle housing cover. Loosen cover bolts, and drain oil. Remove cover. 2. Remove differential pinion-shaft lock bolt. Remove pinion shaft from differential. Push in axle. Remove “C” clip from axle at pinion gear. Remove axle from tube. Remove axle shaft seal and bearing from axle tube. Installation 1. Grease bearing, and install into axle tube. Ensure bearing part number is facing outwards. Apply wheel bearing grease to axle shaft seal. Install seal in axle tube. Install axle shaft. 2. Install axle “C” clip. Pull axle out to seat “C” clip. Install pinion shaft. Install lock bolt, and tighten to specification. Apply RTV to axle housing cover. Tighten cover bolts to specification. See TORQUE SPECIFICATIONS table. Fill with gear oil. Removal (Model 198, 1999 Grand Cherokee 216 & 226 Axles) 1. Raise and support vehicle. Remove rear wheel(s). Remove brake drum. Remove nuts securing axle retainer plate to axle tube, and discard. Using slide hammer and Adapter (6790), remove axle shaft from axle tube. 2. Using a 3/8″ drill bit, drill a shallow hole into bearing retaining ring on axle. DO NOT drill into axle. Using a cold chisel, cut bearing retaining ring across drilled hole, and remove from axle shaft. Using a press and Bearing Remover (1130), remove bearing from axle shaft. Remove seal and retainer plate from axle shaft. Installation 1. Ensure axle shaft retaining plate is flat and not warped. Install retaining plate on axle shaft. Apply wheel bearing grease to axle shaft seal. Install seal on axle shaft. Grease bearing, and install on axle shaft with outer surface groove facing seal. 2. Using press and Bearing Installer (7913), press bearing onto axle shaft. Press NEW bearing retainer ring onto axle shaft. Install axle shaft in axle tube. Tighten NEW axle retainer plate nuts to specification. See TORQUE SPECIFICATIONS table. PINION SEAL & YOKE Removal

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, exploded view 1996 jeep grand cherokee exploded view of front suspension, Meritor Axle Nut Torque Specs, Silverado Rear Axle Seal Replacement, how to remove right front axle 95 bronco, saturn sl hub bolt torque, DIY LEXUS GX 470 AXLE REPLACE, how to remove axle seal in a 1999 chevy malibu, size axle nut 2005 explorer, 2002 ford expedition trailing arm torque specs

1994 Nissan Maxima SE FWD Axle Shafts Removal And Installation Manual

0

Filed Under (Nissan Manuals) by admin on 21-05-2011

download
FWD AXLE SHAFT Removal 1. Raise and support vehicle. Remove wheel. Remove wheel bearing lock nut from end of drive axle. Remove disc brake caliper and suspend out of way. DO NOT allow caliper to hang by hydraulic hose. 2. Separate tie rod end from steering knuckle. Remove axle shaft from steering knuckle hub using a soft mallet. On models with ball and cage type right axle shaft, remove support bearing retainer-to-block bolts. See Fig. 4 . 3. On all models, pry right axle shaft from transaxle using screwdriver. See Fig. 1 . On M/T models, pry left axle shaft from transaxle using screwdriver. On A/T models, insert screwdriver through right axle shaft hole in differential, and drive out left axle shaft. See Fig. 2 1. Place axle shaft in soft-jawed vise with inner joint facing up. Remove boot clamps. See Fig. 4 . Mark slide joint housing and inner race in relation to axle shaft for reassembly reference. 2. Remove and discard snap ring “A”. See Fig. 3 and Fig. 4 . Remove slide joint housing. Remove snap ring “C”. Remove cage, inner race and balls as an assembly. Remove snap ring “B”. Cover axle shaft splines with tape. Remove boot. 3. To disassemble support bearing and retainer assembly on right axle shaft, remove dust shield and snap ring “D”. See Fig. 4 . Press axle shaft out of support bearing and retainer assembly. Remove snap ring and dust shield from retainer. Using bearing driver and hammer, drive support bearing out of retainer.

1994 Ford Explorer SPINDLE AND SHAFT ASSEMBLY REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 01-02-2012

download
Removal 1. Raise and support vehicle. Remove wheel assembly. Remove caliper from rotor. Remove locking hub. See AUTOMATIC LOCKING HUBS or MANUAL LOCKING HUBS under REMOVAL & INSTALLATION. 2. Remove wheel bearings, lock nuts, hub and rotor. Remove spindle-to-steering knuckle nuts. Tap spindle with plastic hammer to free spindle from steering knuckle. See Fig. 9 . Remove spindle, spindle seat (if equipped) and splash shield. 3. On right side applications, remove and discard keystone clamp from shaft assembly and stub shaft. Slide rubber boot onto stub shaft. Remove shaft assembly from right axle. See Fig. 9 . 4. Remove left shaft assembly (if required). On all applications, wrap spindle in protective cloth and place second step of spindle in soft-jawed vise. 5. On Explorer and Ranger, remove oil seal using slide hammer and Seal Remover (TOOL-1175-AC). Remove needle bearing from spindle. Press seal from shaft assembly. See Fig. 9 . 6. On Bronco and F150, remove needle bearing and oil seal using slide hammer and Cup Puller (T77F- 1102-A). Press seal from shaft assembly. Installation 1. Clean all dirt and grease from spindle bearing bore. Ensure bearing bore is free of nicks and burrs. On Explorer and Ranger, install seal on shaft assembly using press and Seal Installer (T83T-3132-A). 2. On Bronco and F150, install seal on shaft assembly, with seal lip toward spindle. On right side applications, install rubber boot and NEW keystone clamps on stub shaft. Install right shaft assembly into stub shaft, with stub shaft missing spline aligned with shaft assembly. 3. Ensure splines are fully engaged. Install rubber boot over assembly and tighten keystone clamps. On left axle applications, install shaft assembly through steering knuckle, and engage in splines. 4. Install needle bearing in spindle, with manufacturer identification mark facing away from spindle bore. For bearing installation, use Handle (T80T-4000-W), and Bearing/Seal Installer (T83T-3123-A for Explorer and Ranger; T80T-4000-S for Bronco and F150).

Related Content:

2005 f150 half wrap, how to replace a turbine speed sensor on a 1998 ford explorer, remove shaft 326rx service manual, spindle nut torque 2007 ford 150

LEAKS FROM REAR HALFSHAFT AXLE SEAL REPAIR MANUAL

0

Filed Under (More Manuals) by admin on 15-06-2012

download
FORD: LINCOLN: 2002-2006 Explorer 2003-2005 Aviator 2003-2006 Expedition 2003-2006 Navigator MERCURY: 2002-2006 Mountaineer This article supersedes TSB 05-15-5 to update the 3. Do not use a damaged seal installation tool vehicle model years, Parts, and Service Procedure. exhibiting nicks, burrs, or sharp edges. NOTE ISSUE THE USE OF SEAL PROTECTOR 1L2W-4N206-AA Some 2003-2006 Expedition/Navigator, 2002-2006 IS NO LONGER REQUIRED. Explorer 4dr/Mountaineer, and 2003-2005 Aviator vehicles equipped with the 8.8? or 9.75? ring gear 4. Do not tap directly on the back of the seal and independent rear suspension (IRS), may exhibit installation tool, always tap on the handle, per leaks at the rear halfshaft axle seals. A new Instruction Sheet. Seal should be driven evenly unitized seal is now available for service. The new into housing bore with only enough force to seal design eliminates the need to use seal seat in the bore. protectors during installation. Removal of the excluder seal (1L2W-1N013-BA) if present is 5. Before installing the halfshaft, verify that the required. inboard excluder seal (1L2W-1N013-BA) is not present on the halfshaft. If the excluder seal is ACTION present, follow the kit Instruction Sheet and Order and install the new seal kit to correct the leak remove the excluder seal. condition. Review the updated instruction sheet NOTE included in the kit and obtain the required tools before beginning repair. OVERFILLING THE AXLE CAN INCREASE POTENTIAL FOR LEAKS. INSTALLATION SERVICE TIPS PART NUMBER PART NAME Refer to the appropriate Workshop Manual, Section 7L1Z-4A109-B Axle Shaft Seal Kit (9.75 Axle) 205-02 for half shaft removal and installation. 7L1Z-4A109-C Axle Shaft Seal Kit (8.8 Axle) NOTE IN THE WORKSHOP MANUAL UNDER THE HALF WARRANTY STATUS: Eligible Under Provisions Of SHAFT REMOVAL/INSTALLATION SECTION New Vehicle Limited THERE ARE ADDITIONAL PARTS CALLED OUT Warranty Coverage THAT ARE REQUIRED TO BE REPLACED. OPERATION DESCRIPTION TIME THESE PARTS ARE NOT INCLUDED IN THE 062205A 2003-2006 0.8 Hr. AXLE SHAFT SEAL KIT LISTED. Expedition/Navigator: Replace Rear Axle (Stub) 1. Use only the proper seal installation tool, Lisle Shaft Seal Includes Time Special Seal Installer (LIS 17850) available To Remove And Install through the Rotunda Technician Tool Program. Halfshaft One Side (Do Not Use With 4139A, 2. Ensure the seal installation tool is clean and 4139A2) free of debris prior to inserting into new seal.

Related Content:

2004 ford explorer manual download, Lincoln pa66-gf30 w584a, 2003 ford explorer rear differential removal, removing stuck halfshaft 03 explorer, Free Mercury Mountaineer Repair Manual, free 2002 lincoln ls chilton manual, Ford Five Hundred Repair Manual, 2006 mountainee repair manual, 2006 Ford explorer manual online, 2006 ford explorer manual download

1991 Infiniti G20 AXLE SHAFTS – FRONT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Infiniti Manuals) by admin on 13-02-2012

download
REMOVAL & INSTALLATION FWD AXLE SHAFT Removal (Axle Shaft) 1. Raise and support vehicle. Remove front wheel assembly. Remove wheel bearing lock nut. Remove brake caliper, and support aside. Remove brake rotor. 2. Disconnect tie rod end. Remove upper knuckle nut, and separate knuckle assembly from third link assembly. Push axle shaft through hub, and separate axle assembly from knuckle assembly. 3. Insert screwdriver blade between transaxle case and right axle inner CV joint. Pry out on joint until joint pops free. Use care not to damage axle boot or axle seal. 4. On M/T vehicles, remove left axle in same manner. On A/T vehicles, insert screwdriver through differential, and drive axle out of transaxle case using a hammer. See Fig. 2 . PROBLEM Possible Cause/Action GREASE LEAKING Ripped CV Boot Replace Boot CLICKING NOISE WHILE CORNERING Dry/Worn CV Joints Replace Outer CV Joints CLUNK ON ACCELERATION Dry/Worn CV Joints Replace Inner CV Joints Worn Transmission Gears/Bearings Inspect Transmission VIBRATION/SHUDDER ON ACCELERATION Dry/Worn CV Joints Replace CV Joints Alignment Out Check Alignment Incorrect Spring Height Check Spring Height SQUEALING OR HUMMING Dry/Worn CV Joints Lube/Replace CV Joints Faulty Wheel Bearing Replace Wheel Bearing NOTE: DO NOT allow brake caliper to hang from brake hose. CAUTION: Use care not to damage pinion mate shaft or side gear while driving out axle. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 2
Fig. 2: Removing Left Drive Axle (A/T Vehicles) Courtesy of NISSAN MOTOR CO., U.S.A. Removal (Outer CV Joint) 1. Remove and discard boot bands. Slide boot off joint housing. Thread wheel bearing lock nut onto joint. Using a slide hammer and bearing puller, remove joint from axle shaft. See Fig. 3 . NOTE: Outer joint cannot be disassembled. Remove and inspect joint and replace if damaged or worn. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 3 2. Remove circlip from end of axle, and remove boot. If boot is being reused, take care not to cut boot on axle splines during removal. Clean CV joint in suitable solvent. Inspect components, and replace joint if necessary.

Related Content:

1991 ford ranger manual, shopmanuel for 1991 chevy cavalier, car manual for 1991 lexus ls400, how do i remove cv shaft on 1996 infiniti g20, snap and pop from axel when cornering in silverado, transaxle play in Nissan sentra

2001 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 18-02-2012

download
Wheel Hub Removal All vehicles 1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 . 2. NOTE: Caliper is removed for clarity. Position aside the front disc brake caliper and anchor plate (2B292). 1. Remove the two front disc brake caliper anchor plate bolts. 2. Remove the front disc brake caliper anchor plate and position aside. 3. NOTE: Carry out this step for F-250 and F-350 4×4 SRW vehicles. Remove the rotor. 4. NOTE: Carry out this step for DRW vehicles. NOTE: If excessive force must be used during brake rotor removal, the brake rotors should be checked for lateral runout prior to installation. For additional information, refer to Section 206-00 . Remove the eight hub extender nuts, the hub plate and the rotor. 1. Remove the eight hub plate nuts. 2. Remove the hub plate. 3. Remove the rotor. 5. Remove the hub lock. 1. Remove the retainer ring. 2. Pull outward and remove the hub lock. 6. Remove the axle shaft thrust washers. 1. Remove the snap ring. 2. Remove the three thrust washers. Vehicles equipped with ABS 7. sensor from the bearing. Disconnect the ABS wheel sensor harness. 1. Disconnect the connector. 2. Disconnect the harness routing clips. All vehicles 8. NOTE: The wheel hub and bearing is a slip fit design and should not require a puller to remove it. Remove the wheel hub and bearing. 1. Remove the four lock nuts. 2. Remove the wheel hub and bearing 9. If necessary, remove the brake disc shield. Vehicles with ABS 10. If necessary, remove the bolt and the ABS sensor. All vehicles 11. NOTE: If necessary, position the hub in a soft-jawed vise. Install two nuts on the studs and use the inner nut to remove the studs. 12. Remove and discard the O-ring. Installation All vehicles 1. NOTE: Any time the wheel hub is removed for any reason, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive operations. Install a new O-ring. 2. NOTE: Position the hub in a soft-jawed vise. Install two nuts on the studs and use the outer nut to install the studs. Vehicles equipped with ABS 3. Position the ABS sensor and install the bolt. All vehicles 4. Position the brake disc shield. 5. NOTE: Apply a coat of Ford High Temperature 4×4 Front Axle and Wheel Bearing Grease E8TZ-19590-A meeting Ford specification ESA-M1C198-A to the O-ring area of the wheel hub and bearing before installing the hub and bearing. Install the wheel hub and bearing. 1. Position the wheel hub and bearing. 2. Install the four lock nuts. Vehicle equipped with ABS 6. NOTE: The following step applies only to vehicles equipped with ABS. Connect the ABS sensor harness. 1. Position the ABS sensor harness and install the routing clips. 2. Connect the harness connector. All vehicles 7. n-metallic thrust washer must be installed between the two metal thrust washers. Failure to do so will cause severe wear to the non-metallic thrust washer, allowing the axle shaft to travel further in and out during torque thrust causing damage to the wheel hub and bearing, the axle shaft end seal and the axle shaft. Install the snap ring. 1. Position the three thrust washers onto the axle shaft. 2. Install the snap ring. 8. NOTE: Any time the hub lock is removed, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive functions. Install a new O-ring. 9. Install the hub lock. 1. Position the hub lock. 2. Install the retainer ring. 10. Position the front disc brake rotor (1125) to the wheel hub (1104). Make sure the wheel hub and the front disc brake rotor braking and mounting surfaces are clean. ? Use brake parts cleaner to clean the front disc brake rotor. 11. NOTE: Carry out this step for DRW vehicles only. Install the front wheel hub extender and nuts.

Related Content:

1995 ford 150 4 wheel drive front hub removal, Need to torque specifications 1999 GMC 1500 wheel hub bearings, snap ring assemble, 2009 impala hub mounting bolt torque, 1998 f250 4x4 front hub bearings torque specs, how to remove a rusted hub assembly, 1977 ford f-350 rear wheel diagram, removing rear axle bearing 2002 toyota tacoma, removing rear wheel bearing race in 06 f-250 super duty lariat, how to change rear hub assembly on a 2006-2010 saturn vue with disk brakes

1989 Toyota 4Runner ENGINE PERFORMANCE Removal Overhaul And Installation

0

Filed Under (Toyota Manuals) by admin on 26-10-2011

download
CARBURETOR (COROLLA) REMOVAL 1) Drain cooling system. Disconnect air intake hose. Disconnect emission control hoses from air cleaner. Remove air cleaner mounting bolt and wing nut. Remove air cleaner. 2) Disconnect accelerator cable. Disconnect throttle cable (A/T). Disconnect carburetor wiring connector. Disconnect emission control hoses and tag for installation. Disconnect fuel inlet hose. Remove 4 carburetor mounting nuts and No. 1 vacuum pipe. Remove carburetor. DISASSEMBLY Air Horn 1) Remove air cleaner setting bolt. Remove fuel pipe clamp, union, fuel pipe and gaskets. Remove vacuum hoses. Remove pump and pivot screw and pump arm with connecting link. Disconnect choke link and choke opener link. 2 Remove 8 air horn screws and number plate, fuel pipe support and wire clamps. Remove air horn from carburetor body. Disconnect wiring from solenoid valves. 3) Remove float pivot pin, float and needle valve assembly. Remove air horn gasket, needle valve seat and gasket, power piston retainer, power piston and spring. Remove pump plunger and boot. See Fig. 2.
Fig. 1: Exploded View of Aisan Carburetor Main Body (Corolla) Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 2: Exploded View of Air Horn Assembly (Corolla) Courtesy of Toyota Motor Sales, U.S.A., Inc. Main Body 1) Remove solenoid valves from carburetor body. Remove stopper gasket. Disconnect throttle positioner links and remove bracket attaching bolts. Remove accelerator pump retainer gasket and remove pump discharge weight, long spring and discharge large ball. See Fig. 1. 2) Remove pump dampening spring. Using tweezers, remove plunger retainer and check ball. Disconnect throttle positioner link and throttle position levers, washer and spring. Remove primary and secondary main passage plugs and gaskets. Remove primary and secondary main jets and gaskets. 3) Remove auxiliary acceleration pump (AAP) housing, spring and diaphragm. Remove AAP inlet plug and check ball. Remove outlet plug, short spring and small ball. Remove primary and secondary small venturies. 4) Remove sight glass retainer, sight glass and “O” ring. Remove throttle lever return spring and back spring. Remove throttle lever and fast idle cam. 5) Disconnect link and remove secondary throttle valve diaphragm assembly and gasket. Remove throttle position switch and bracket. Remove 3 body-to-flange screws and vacuum passage screw. Separate body from flange. See Fig. 3. Remove washer from throttle valve shaft. Remove idle mixture adjusting screw and idle speed adjusting screw.

Related Content:

yhs-mystartdefault, toyota 4k carburetor manual download, remove center peice from 2011 toyota camry, 2005 tundra grill removal, how to check windshield wiper motor and arm on a 2007 malibut, how replace alternator in 2006 honda odessey, how remove intake plenum on 1998 Toyota sienna, toyota sienna grill removal, jaguar fuel hose removal, how to remove center console 2013 camry

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

0

Filed Under (Chevy Manuals) by admin on 14-05-2012

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, how to change evaporator core on 1998 blazer, 2008 yaris hatchback remove headliner replace antenna, Redezvous Dash Removal, 2005 buick lesabre instrument cluster removal, remove 2010 highlander radio, remove fender 2001 grand prix, 2006 frontier remove window switch panel, remove front dash on 2014 optima

1989 Toyota 4Runner STEERING COLUMN REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 13-11-2011

download
REMOVAL & INSTALLATION STEERING COLUMN Removal 1) Disconnect battery ground cable. Remove steering wheel. On Cressida, Corolla, MR2 and Tercel models, remove fuse box cover, lower instrument trim panel and air duct from under steering column. 2) On all models, remove upper and lower steering column covers. Remove combination switch. Mark position of “U” joints and shaft for reassembly. 3) On models with “U” joints, remove “U” joint retaining bolt. On models with flexible joint, remove flexible joint retaining bolt. NOTE: On 2WD Pickup models, remove steering column with intermediate shaft attached. 4) On all models, mark position of joint and pinion shaft for reassembly. Remove intermediate steering shaft. 5) Remove floor pan cover bolts. Remove tilt bracket-to- dashboard mounting bolts. Remove steering column toward inside of vehicle. Fig. 1: Exploded View of Camry, Corolla, MR2 & Tercel Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 2: Exploded View of Celica, Cressida & Supra Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 3: Exploded View of Land Cruiser, Pickup, Van & 4Runner Steering Column Assembly Courtesy of Toyota Motor Sales, U.S.A., Inc. Installation 1) To install steering columns, reverse disassembly procedure. Grease main steering shaft and all bearings. 2) Ensure marks made to flexible couplings and to “U” joints are aligned. Ensure steering column and shafts do not bind after installation. STEERING COLUMN OVERHAUL NOTE: Camry, Corolla, MR2 and Tercel steering columns are similar. Some of the following procedures will not pertain to all models. Disassembly (Camry, Corolla, MR2 & Tercel) 1) Remove tension springs, grommets and screws from tilt bracket. Remove tilt lever left-hand set bolt. Remove column upper support lock bolt. 2) Remove tilt steering support bolts and pawl set bolts. Place bushings and “O” rings aside and keep them clean. Remove ignition lock cylinder. 3) Using a screwdriver, push 2 thrust stoppers into bearing retainers. Pull out shaft from column. Remove the No. 1 column ring, bearing retainer, thrust stoppers and No. 2 column ring from shaft. 4) Remove snap ring and lower bearing from shaft. Remove bearing inner snap ring. Remove upper bracket retaining bolts and ground strap. Separate upper bracket from column. Inspection 1) Check that steering lock mechanism operates properly. Check upper bearing for smooth rotation or excessive noise. Replace upper bearing (if necessary). 2) Using Drift (09631-00020) and Adapter (09627-30010), drive bearing from upper bracket. Pack new bearing with grease. Using the same drift and adapter used in removal, drive new bearing into upper bracket. 3) Inspect lower bearing for smooth rotation or excessive noise. If lower bearing shows signs of wear or damage, replace with a new one. Reassembly 1) Install upper bracket onto column. Install ground strap. Tighten retaining bolts to 14 ft. lbs. (19 N.m). Install inner snap ring on shaft groove nearest to center of shaft. 2) Install lower bearing and lower bearing snap ring. Place No. 2 column ring into position next to bearing on side nearest center of shaft. See Fig. 4.

Related Content:

2003 toyota camry 2 4 main crankshaftbearing removal, stearing colium cover removel 2003 buick reagel, Reinstall steering column for 1992 Toyota Camry, kia sorento front drive shaft center bearing removal, kia sorento center support bearing removal, kia sorento 2007 manual driveshaft carrier bearing, jeep upper bearing pulls out, how to remove steering column cover on 1994 mitsubishi gt3000, does the center bearing on a 2007sorento require lubrication, 2007 kia sorento center support bearing

2002 Land Rover Freelander (LN) Camshaft Timing Belt Service Repair

0

Filed Under (Land Rover Manuals) by admin on 09-01-2012

download
Service Repair No – 12.65.18 Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt . 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash shield to body and remove shield. 5. Remove 3 bolts securing camshaft timing belt LH rear cover and remove cover. 6. Rotate crankshaft in a clockwise direction and align the engine “SAFE” position, notch on crankshaft pulley aligned to the “ARROW” on front mounting plate and the timing marks aligned on the rear camshaft gears as illustrated 7. Remove bolt securing PAS pipe to engine front mounting plate. 8. Remove 3 Torx screws securing PAS pump pulley and remove pulley. Zoom Sized for Print Zoom Sized for Print Zoom Sized for Print 9. Remove 3 bolts securing PAS pump to front mounting plate and tie pump aside. 10. Release alternator battery lead terminal cover, loosen terminal nut and disconnect lead from terminal. 11. Disconnect multiplug from alternator. 12. Remove lower bolt and upper nut and bolt securing alternator to front mounting plate. 13. Remove alternator. 14. Remove Torx screw securing idler pulley to front mounting plate and remove pulley 15. Loosen bolt securing lower engine steady to front subframe. 16. Remove bolt securing lower engine steady to sump mounting, release lower engine steady from sump mounting. 17. Remove 3 bolts securing camshaft timing belt RH front cover and remove cover 18. Remove 3 bolts securing camshaft timing belt LH front cover and remove cover. 19. Assemble LRT-12-161 to LRT-12-199 and secure with clamp bolt. 20. Insert LRT-12-161 with LRT-12-199 into crankshaft pulley, loosen and remove pulley bolt. 21. Remove special tool from crankshaft pulley and remove crankshaft pulley. 22. Remove 3 bolts securing camshaft timing belt lower cover to cylinder block and remove cover. 23. Remove 2 bolts securing ancillary drive belt tensioner and remove tensioner. 24. Note fitted position of heat shield on A/C compressor and remove 3 bolts securing A/C compressor to front mounting plate and cylinder block. Release A/C compressor and heat shield and position aside. 25. Drain engine oil.

Related Content:

accessory drive timing marks cummins m11, 05 sport trac crank pulley tighten, camshaft bolt removal tool ford escort, how much is a camshaft pulley for 2005 mazda 6, mazda 3 crankshaft pulley broken bolt removal, montero sport how do i remove it cam seal nut, how to remove rear cargo cover in venza, how to remove pulley tensioner on a 99 mercury sable, perkins AR70498 front cover, removing a crankshaft starlet

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, exploded view 1996 jeep grand cherokee exploded view of front suspension, Meritor Axle Nut Torque Specs, Silverado Rear Axle Seal Replacement, how to remove right front axle 95 bronco, saturn sl hub bolt torque, DIY LEXUS GX 470 AXLE REPLACE, how to remove axle seal in a 1999 chevy malibu, size axle nut 2005 explorer, 2002 ford expedition trailing arm torque specs