Skip to content

how to remove front bumper toyota camry

You search PDF repair manual about how to remove front bumper toyota camry, if there are search results will appear below. If search results do not exist, please search by others keyword.

Toyota Tundra Front Winch Bumper Installation Instructions

download
Installation Instructions Toyota Tundra Front Winch Bumper Product Number: H1850, H1851, H1852 Application: ’07-Current Toyota Tundra Copyright sing a deep 14mm socket and breaker bar, loosen the 4 14mm nuts located at the connection between the factory frame end and the bumper. See Image Below. G. Remove the bumper by pulling forward away from the vehicle and rolling forward. H. Remove the two (per side) plastic clips from the painted plastic trim pieces located below the headlights. The Hood must be open for this. See Image Below. I. Remove these plastic painted trim pieces by pulling directly away from the front of the truck. Do not discard these! J. Remove all pop rivets (8 Total) from the front painted plastic bumper upper fascia. See Image Below. K. Remove all bolts holding the painted plastic fascia piece using a 10mm socket and wrench (16 total). See Image Below in addition to Image Above. L. Remove the Phillips pop rivet holding the fascia to the inner fender. 1 per side. M. Remove the two(one per side) 10mm screws from the recessed hole in the inner fender well. N. Pull the edges of the plastic fascia from the truck and directly away from the front to snap free. Set fascia aside. O. Remove the two 10mm screws using a socket from the plastic spacer pieces located on the lower fender. With Screws removed pull bracket straight off the truck. Complete on opposite side. See Image Below Pre-Installation Assembly A. Remove the Bumper from the shipping carton. Lay all items out on a blanket to prevent damage to the powder coating. B. OPTIONAL: If installing winch and roller fairlead (neither provided) into bumper, do it at this time. Follow the winch Manufacturers instructions to mount the fairlead to the front of the bumper and the winch itself to the 4 hole pattern on the internal winch tray of the bumper. C. Install turn signal into light pockets as shown using self- tapping screws as shown below.

TOYOTA FJ CRUISER – FRONT BUMPER INSTALLATION INSTRUCTIONS

download
Front Bumper Installation – TOYOTA FJ CRUISER Step 1 Very Important Before beginning installation, assure that vehicle has been pulled forward into work-area with the wheels straight and that the ground is level. The clearances around the FJ bumper are critical to proper installation and fitment. Moving vehicle with wheels turned causes slight frame twist preventing ease of removal of OE bumper and installation of new bumper without issue. Make sure you have plenty of room to work around front of vehicle. Open the hood at this time, you will need to see down through the inner-body core-support while removing your OE bumper and installing your Body Armor FJ Bumper. Step 2 a. Unpack bumper using staple puller to remove staples. Save all packing materials and take care not to tear cartons. b. Remove hardware and misc.parts. Check parts/hardware list to confirm all parts and necessary hardware are included. c. It’s a good idea to spray all OE attaching hardware at this time with penetrating oil before beginning removal of OE bumper. This will ease removal as well as to help assure that none of the bolts’ / nuts’ threads are damaged during removal. Use extra caution when working with the bumper mounting studs & nuts. Step 3Prep bumper for install: You may install your auxilary lights in the light pockets. The light tab is slotted to allow for adjustment for adjustment for light grilles. You may also attach a second set of lights on the top deck . Also attach the grill guard at this time. Step 4 a. Begin removing OE bumper following instructions and photos on the following page for detailed descriptions and references. When done, proceed to Step 4 here. Step 5 a. If equipped, remove OE chassis skid plate and set aside for install after new bumper is installed. Save OE hardware to re-install the skid plate once new bumper is installed (3 upper bolts and 2 lower bolts, lowers have spacers between frame & skid plate). b. Remove the (3) outer hold-down hex nuts holding bumper to frame-caps on both passenger and driver sides. Un-clip the outer ends of the bumper from the outer bumper support clips (see Photo 5 on following page) by pulling bumper fascia down and out of clip on driver and passenger sides. Next, while a helper holds the bumper in place, loosen and remove the inner hold-down hex nuts on both passenger and driver sides. Reference Photo 1 on the last page for stud locations. The bumper should now slide off the front of the locating / mounting studs in the frame-caps. Remove slowly prevent paint damage. Save hold-down nuts. c. Remove the outer bumper support clips from both driver and passenger sides (see Photo 5 on following page) Step 6 a. If you bought a winch, skip to Step 6b. If you did not purchase a winch, you can mount the winch cover plate / lower bumper fascia, and fairlead slot cover plate to the bumper now, using (6) 3/8″ x 1″ bolts with (2) flat washers, (1) lock washer, and (1) hex nut on each bolt. See photos 4 & 5 on the last page for reference. b. If you purchased a winch for your FJ, now is the time to mount it in the bumper. The winch will bolt down using the fairlead mounting bracket and 10mm bolts to secure winch & fairlead bracket to bumper. The roller fairlead bolts to the fairlead bracket using the 1/2″ hex nuts supplied. See photo 3 on the last page for reference. Be sure to mount with the correct side of winch to passenger side for solenoid pack installation / clearance. Once the winch is bolted in, you can mount the winch cover plate / lower bumper fascia to the bottom of the bumper using (4) of the 3/8″ x 1″ bolts with (2) flat washers, (1) lock washer and (1) hex nut on each bolt. If you purchased lights, mount them to the light tabs. It the lights have a protective grille you should be able. to use the cover. Important: Follow winch mfr’s directions for cable to winch / solenoid / battery connections. Use caution to assure clearance of any and all bumper / winch / mounting surfaces at all cable end connections. Coil cables and lay in winch mount plate to protect against damage while installing bumper onto vehicle. Place coiled cables in winch mount plate to assure no interference with the radiator, a/c line and / or inner body core support during bumper installation. Cables to be run in Step 7. Step 7 Along with your helper, one person on each side, guide your Body Armor FJ Bumper onto the the frame-cap mounting studs. Use caution guiding the bumper on slowly and evenly to prevent paint damage. Locating / mounting studs and bumper mounting plates can be seen down through inner-body core support while guiding bumper into place. Make sure the bumper does not contact grill or fascia while installing bumper as this can cause paint damage. While you or your helper hold the bumper in place, thread the OE hold-down nuts onto mounting studs to hold the bumper in place, hand tighten at this time. Step 8 Confirm bumper is even side-to-side, torque hold-down nuts to 80 ft.lbs. Again confirm bumper is even and there are no clearance issues between the bumper and any part of the body and / or inner-body core-support. You can now run the winch cables through the inner-body core support to the battery. If you purchased a set of lights to be used with your bumper, you can now wire them up, please follow the detailed light manufacturer instructions. **Body Armor is not responsible for any issues with respect to the wiring, operation or warranties to the lights Step 9 a. Fit the wheel well inner-liner end-caps to the bottom of the bumper at each corner and bolt up with supplied 1/4″ x .75″ phillips- head machine screws, (2) each side, into drilled / threaded holes in bottom corners of bumper. See photos 6 & 7 on the last page. b. Next, using the OE hardware and spacers, re-install your chassis skidplate, making sure it’s straight before tightening. c. Using the (2) remaining 1/4″ x .75″ phillips-head machine screws, mount your license plate to threaded holes in the bumper face. d. Re-install the grill by snapping onto clips and using the OE push-pins and screws to hold down in OE locations. ** trimming off the front inner fender is a customer option, it is not required. We recommend you check the torque of all bolts after about two weeks, and after every off-road / trail run thereafter to assure tightness

2004 Toyota Camry Disc Brake System Service/ Repair Manual

download
OVERHAUL HINT: Overhaul the RH side by the same procedures with LH side. REMOVE FRONT WHEEL 1. DRAIN BRAKE FLUID NOTICE: Wash off the brake fluid immediately if it comes into contact with a painted surface. 2. DISCONNECT FRONT FLEXIBLE HOSE 3. Remove the union bolt and a gasket from the disc brake cylinder, then disconnect the flexible hose from the disc brake cylinder. a. REMOVE DISC BRAKE CYLINDER ASSY FR LH 4. Remove the 2 bolts and disc brake cylinder. a. REMOVE DISC BRAKE PAD KIT FRONT (PAD ONLY) 5. Remove the 2 brake pads with anti-squeal shim. a. 6. Remove the 2 anti-squeal shims from each of 2 brake pads . a. Using a screwdriver, remove the wear indicator from each of 2 brake pads . b. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 7. Remove the upper side front disc brake pad support plate. a. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE 8. Remove the bottom side front disc brake pad support plate. a. 10. Remove the cylinder slide bush from the cylinder slide pin. a. REMOVE FRONT DISC BRAKE BUSH DUST BOOT 11. Remove the 2 bush dust boots from the disc brake cylinder mounting. a. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH 12. Remove the 2 bolts and disc brake cylinder mounting LH. a. 13. Using a screwdriver, remove the set ring and cylinder boot. a. REMOVE FRONT DISC BRAKE PISTON 14. Place a piece of cloth or similar, between the piston and the disc brake cylinder. a. Use compressed air to remove the piston from the disc brake cylinder. CAUTION: Do not place your fingers in front of the piston when using compressed air. NOTICE: Do not spatter the brake fluid . b. 2004 Toyota Camry L4-2.4L (2AZ-FE) REMOVE PISTON SEAL 15. Using a screwdriver, remove the piston seal from the disc brake cylinder. NOTICE: Do not damage the inner cylinder and the cylinder groove. a. REMOVE FRONT DISC BRAKE BLEEDER PLUG CAP 16. REMOVE FRONT DISC BRAKE BLEEDER PLUG 17. INSPECT BRAKE CYLINDER AND PISTON Check the cylinder bore and piston for rust and scoring 18.

2007 Toyota Camry Billet Bumper Grille Installation Instructions

download
Step 1: Remove the 2 screws that hold the top portion of the front fascia to the core support. Figure 1 Step 2: Remove the 2 push clips that hold the top portion of the front fascia to the core support. Figure 2 Figure 1 Figure 2 Step 3: Remove the bolt that holds the center of the front fascia to the core support. Figure 3 Step 4: Rock the top portion of the front fascia forward to gain access to the backside of the factory grille shell. Step 5: There are 16 clips that hold the factory grille shell and most should come undone by pulling out on the grille shell, some of them may need to be unclipped from the backside and then remove the factory grille shell from the front fascia. Figure 4 Step 6: Install the fully threaded studs into the threaded tabs on the backside of the billet grille. Step 7: Center the billet grille into the bumper opening. Step 8: Coming in through the factory grille shell opening install the powder coated brackets over the fully threaded studs and hold in place using the k-lock nuts. Figure 5. The photo was taken without the grille being installed. The grille must first be installed onto the vehicle then the powder coated brackets placed over the fully threaded studs. Figure 5 Step 9: Re-center the billet grille to your liking and secure all hardware. Step 10: If you are installing part# 807196 now is the time to do so. Step 11: Reattach the front fascia to the vehicle using the hardware saved from steps

2007-2010 Toyota Camry Hybrid Vehicles Potential Floor Mat Interference with Accelerator Pedal

download
The owner notification will commence in early February, approximately one week after your dealership has been notified. This campaign will be launched in phases. • The first phase will include certain 2007 through 2010 model year Camry and Camry Hybrid vehicles equipped with Denso accelerator pedals. These owner letters will be mailed over a period of several weeks. • Additional models, including Camrys equipped with a CTS accelerator pedal will be launched in later phases as the remedy is developed. • Information on additional phases related to Camry (equipped with a CTS accelerator pedal), Avalon, Corolla, Highlander, Matrix, Prius, Tacoma, Tundra and Venza will be provided prior to the launch of these phases. If your dealership is contacted by an owner of a Denso pedal equipped Camry who has not yet received a notification, please verify eligibility by confirming through Dealer Daily/TIS prior to performing repairs . Dealers should perform the repair as outlined in the attached Technical Instructions. 2. Vehicles in Dealer Stock • As required by Federal law, dealers are not to deliver any new vehicles in their inventory, which are involved in a safety recall unless the defect has been remedied. However, because this defect does not exist in vehicles in which the driver’s side floor mat is compatible with the vehicle and properly secured you may continue to sell new vehicles (with Denso pedals) that have not received the full remedy if you assure the driver’s position floor mat is semi-permanently secured or place the front driver’s and passenger’s floor mats in the trunk on any vehicles in stock prior to sale or lease. Vehicle safety recall completion can be verified through TIS. • In order to assure established customers receive priority for the safety recall, we request that this campaign remedy be performed on in-stock Camry and Camry Hybrid vehicles just prior to vehicle delivery where possible. • A VIN list containing vehicles in dealer stock will be provided shortly