Skip to content

how to remove headliner from 2002 pontiac sunfire with sunroof

You search PDF repair manual about how to remove headliner from 2002 pontiac sunfire with sunroof, if there are search results will appear below. If search results do not exist, please search by others keyword.

SKYROOF LSS Electric Spoiler Sunroof with Sliding Panel Shade Installation Manual

download
SUNROOF KIT PREPARATION 1. Verify that sunroof kit is complete and undamaged. 2. Bench test the sunroof to ensure proper operation. Close the glass fully before continuing. 3. Cover the vehicle interior to keep clean and prevent damage. SUNROOF INSTALLATION 4. Position the sunroof : Place the interior shade tray against the interior headliner and position to avoid any obstructions, allowing 4 inches clearance in front for the motor. Consider obstructions hidden by the headliner such as roof header, side rails and cross bows. NOTE: motor can be located above most consoles. Place the point of a scratch awl against the center inside front lip of the headliner ring (inside edge of the shade tray). Pierce the headliner, and make a slight dent in the roof panel that will be easily visible on top of the vehicle 5. Carefully remove the entire headliner board from the vehicle. 6. If applicable, remove anti-flutter roof bows from the inside of the roof. Do not remove, cut or modify any structural braces, headers or side rails. 7. Measure and mark a front-to-rear center line on the outside of the roof with a marking pencil. Draw a “reference mark” crossing the center line at the roof dent made in step 4. Measure and mark the front cut line 1¼ inches in front of this reference mark. 8. Align the template centerline to centerline on roof. Align front arrow on the template to front cut line mark. Tape template in place, and apply 2 inch wide masking tape around the outside of the cut line to protect the paint while cutting the roof panel. 9. Make a hole large enough to allow entry of the cutting tool, 1 to 3 inches inside the cut line. If necessary, enlarge the hole using hand held metal snips. Cut the sunroof opening with a suitable metal cutting tool. 10. Use a file to clean up any rough edges or burrs around the sunroof opening. 11. Test fit the sunroof. Trim the hole if required and retest. There should be approximately 1/8 inch (4 mm) clearance front to rear, and side to side. Once proper fit has been achieved, remove the masking tape [ peel inward, toward the opening ] and marking pencil lines from the roof. 12. Apply bare metal primer to the cut edge to prevent the metal from rusting. 13. Clean underside of main frame with wax/grease remover. Apply sealant to the inside lip of the main frame. Use nonacidic silicone, butyl, or the supplied foam tape. If using foam or butyl tape, fully overlap the ends in the rear center at a screw hole. Kit includes foam sealant tape, however some technicians prefer silicone or butyl

Vehicles Equipped with a Webasto Sunroof System

download
Models: 1997-2000 Buick Century 1988-1991 Buick Reatta 1988-1999 Buick Riviera 1989-2000 Buick Park Avenue 1998-2000 Buick Regal 1988-1997 Cadillac Seville 1988-1996 Cadillac Fleetwood 1988-2000 Cadillac Eldorado 1989-2000 Cadillac DeVille 1995-2000 Chevrolet Cavalier 1998-2000 Chevrolet Malibu 2000 Chevrolet Impala, Monte Carlo 1988-1995 Oldsmobile Ciera 1989-1996 Oldsmobile Ninety Eight 1994-1998 Oldsmobile Achieva 1995-1999 Oldsmobile Aurora 1997 Oldsmobile Silhouette 1998-1999 Oldsmobile Cutlass 1998-2000 Oldsmobile Intrigue 1999-2000 Oldsmobile Alero 1987 Pontiac 6000 1989-1998 Pontiac Bonneville 1994-2000 Pontiac Grand Am 1995-2000 Pontiac Sunfire 1997-1998 Pontiac Trans Sport 1997-2000 Pontiac Grand Prix 1997-2000 Chevrolet & GMC S/T Models (Blazer, Jimmy) 1997-2000 Oldsmobile Bravada #99-08-67-003: Info – Vehicles Equipped with a Webasto Sunroof System – (Jul 23, 1999) This bulletin is being revised to update the model information. Please discard Corporate Bulletin Number 43-10-18A (Body Section)

2002 Land Rover Freelander (LN) V6-2.5L Automatic Transmission/Transaxle Service and Repair Manual

download
Automatic Transmission/Transaxle: Service and Repair Gearbox – KV6 – NAS Models JATCO Gearbox – KV6 – NAS models Remove 1. Position the vehicle on a twin-post lift. 2. Tie bonnet back in upright position. 3. Disconnect battery earth lead. 4. Remove engine acoustic cover. 5. Release HO2S multiplug from support bracket on LH camshaft cover, disconnect multiplug. 6. Raise vehicle on lift. 7. Remove rear beam. 8. Remove RH catalytic converter 2002 Land Rover Freelander (LN) V6-2.5L Copyright © 2010, ALLDATA 10.20 Page 3 12. Remove bolt securing front pipe to bracket and remove front pipe. Discard gasket. 13. Remove 3 screws securing LH splash shield and remove shield 14. Release HO2S lead from clip on cylinder block. Remove 4 nuts securing exhaust manifold to cylinder head, remove manifold and discard gasket. 15. Drain fluid from IRD. 16. Drain gearbox fluid. 17. FitLRT-54-026 to the RH drive shaft inboard joint. 18. Using a suitable lever, release drive shaft from IRD. 19. With assistance, pull hub outwards and release drive shaft from IRD. CAUTION: Care must be taken not to damage oil seal when removing drive shaft from IRD. CAUTION: To avoid damage to gaiter or joint, do not allow shaft to hang on joint. 20. Remove LRT-54-026 from RH drive shaft inboard joint.

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

2002 Chevrolet Impala Radiator Air Baffle and Deflector Replacement Manual

download
Radiator Air Baffle and Deflector Replacement – Upper Removal Procedure 1. Remove the radiator air baffle retainers. 2. Tilt the rear of air baffle upward slightly. Slide the air baffle rearward in order to disengage the upper and lower clips of the air baffle from the fascia support. 3. Remove the radiator air baffle. Installation Procedure 2002 Chevrolet Impala 1. Position the radiator air baffle to the vehicle. Tilt the rear of the air baffle upward slightly. Position the upper clip of the air baffle to the lower edge of the front fascia support C-channel. 2. Slide the baffle towards the front of the vehicle in order to completely engage the upper and lower clips of the baffle onto the fascia support. 3. Align the tabs at the rear of the air baffle to the openings in the upper radiator support. 4. Install the radiator air baffle retainers.