Skip to content

how to remove kia optima valve cover

You search PDF repair manual about how to remove kia optima valve cover, if there are search results will appear below. If search results do not exist, please search by others keyword.

2002 Ford Lincoln LS Valve Cover LH Workshop Manual

download
Valve Cover LH Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 . 2. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 . 3. Remove the air cleaner housing. 1. Disconnect the mass air flow (MAF) sensor electrical connector. 2. Remove the bolt. 3. Remove the housing. 4. CAUTION: To disconnect the Norma fitting, squeeze the tabs and pull straight out or damage to the fitting can occur. Disconnect the crankcase ventilation tube. 5. Disconnect the fuel hose. For additional information, refer to Section 310-00 . 6. Disconnect the evaporative emission canister purge valve hose. 7. Remove the vapor management valve (VMV) cover. SECTION 303-01B: Engine — 3.9L 2002 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/17/2001 Material Item Specification 8. Remove the VMV. 1. Disconnect the vacuum hose. 2. Disconnect the purge hose. 3. Disconnect the electrical connector and the push pin. 4. Remove the nuts and the valve. 9. Remove the exhaust gas recirculation (EGR) vacuum regulator solenoid. 1. Disconnect the electrical connector. 2. Remove the screws and the EGR vacuum regulator solenoid. 10. Remove the bracket. 1. Remove the hose. 2. Remove the bracket. 11. Position the engine wiring harness up. 12. Remove the ignition coil cover. * Inspect the gasket and install a new gasket as necessary.

1994 Toyota Paseo ENGINE IDENTIFICATION/ VALVE CLEARANCE ADJUSTMENT

download
1) Disconnect PCV hose, necessary electrical connections and spark plug wires to access valve cover. Remove nuts, seal washers, valve cover and gasket. 2) Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Cylinder No. 1 is front cylinder at timing belt end of engine. Ensure timing mark on crankshaft pulley aligns with “0″ mark on timing belt cover. 3) Ensure valve lifters on cylinder No. 1 are loose and valve lifters on cylinder No. 4 are tight. If conditions are not as described, rotate crankshaft clockwise one complete revolution (360 degrees). 4) Using feeler gauge, measure valve clearance between valve lifter and camshaft on intake valves of cylinders No. 1 and 2, and exhaust valves of cylinders No. 1 and 3. Record valve clearance. Rotate crankshaft clockwise one complete revolution (360 degrees). 5) Measure and record valve clearance on intake valves of cylinders No. 3 and 4, and exhaust valves of cylinders No. 2 and 4. Ensure valve clearance is within specification. See VALVE CLEARANCE SPECIFICATIONS table. VALVE CLEARANCE SPECIFICATIONS TABLE (1) Application In. (mm) Exhaust Valve ………….. .012-.016 (.31-.41) Intake Valve …………… .006-.010 (.15-.25) (1) – Adjust valve clearance with engine cold. 6) If valve clearance requires adjustment, rotate camshaft so lobe on valve to be adjusted is facing upward, away from valve lifter. Position notch area on valve lifter toward inside of cylinder head. DO NOT align notch area with camshaft. Use Valve Clearance Adjuster (SST 09248-55040) to adjust valve clearance. 7) Using SST “A” of valve clearance adjuster, push downward on valve lifter. Place SST “B” between camshaft and valve lifter. See Fig. 2. Ensure enough clearance exists for adjusting shim removal. Remove SST “A”. Fig. 2: Adjusting Valve Clearance Courtesy of Toyota Motor Sales, U.S.A., Inc. 8) Using small screwdriver and magnet, remove adjusting shim. Measure and record thickness of removed shim. Using measured clearance and adjusting shim thickness, select proper replacement adjusting shim. See Figs. 4 and 5. 9) Install replacement adjusting shim. Recheck valve clearance. Apply sealant at indicated valve cover sealing areas on cylinder head. See Fig. 3. 10) Using NEW gasket, install valve cover and sealing washers. Install and tighten nuts to specification. See TORQUE SPECIFICATIONS. To install remaining components, reverse removal procedure. NEW SHIM THICKNESS TAB

2003 Kia Optima L4-2.4L Timing Belt Service and Repair Manual

download
3.Turn the crankshaft clockwise and align the timing marks so as to bring the No.1 cylinder to compression top-dead-center position. At this time the timing marks of the camshaft sprocket and the upper surface of the rocker cover should coincide, and the dowel pin of the camshaft sprocket should be at the upper side. Remove the auto tensioner. CAUTION: Rotate the crankshaft clockwise. 4.Remove the timing belt. NOTE: If the timing belt is reused, make an arrow mark indicating the turning direction (or the front of the engine) to make sure that the belt is reinstalled in the same direction as before 6.When the oil pump sprocket nut is removed, first remove the plug at left side of the cylinder block and insert a screwdriver to check the left counter balance shaft in position. Screwdriver used for this purpose should have a shaft 8 mm (0.3 inch) in diameter which can be inserted more than 60 mm (2.36 inch) 7.Remove the oil pump sprocket retaining nut and remove the oil pump sprocket. 8.Loosen the right counter balance shaft sprocket mounting bolt until it can be loosened by hand. 9.Next, remove tensioner “B” and remove timing belt “B”. CAUTION: After timing belt “B” has been removed, do not attempt to loosen bolt while holding sprocket with pliers, etc. 10.Remove the crankshaft sprocket “B” from crankshaft. INSPECTION Sprockets, Tensioner Pulley, and Idler Pulley 1.Check the camshaft sprocket, crankshaft sprocket, tensioner pulley, and idler pulley for abnormal wear, cracks, or damage. Replace as necessary. 2.Inspect the tensioner pulley and the idler pulley for easy and smooth pulley rotation and check for play or noise. Replace as necessary. 3.Replace if there is grease leak

1999 Dodge Intrepid PRIMARY TIMING CHAIN And SPROCKETS REMOVAL AND INSTALLATION MANUAL

download
Removal 1. Remove upper radiator crossmember. Disconnect fan assembly connector. Remove fan assembly. Remove drive belts. Using Crankshaft Pulley Holder (8191), hold crankshaft pulley and remove center bolt. Using a 3-jaw puller, remove crankshaft pulley. 2. Remove upper intake manifold. See INTAKE MANIFOLD . Remove electrical and vacuum harness retaining clips from valve cover studs. Remove ignition coils. Remove valve covers. Remove power steering pump and set aside. Remove drive belt tensioner pulley and bracket. Remove timing chain cover. 3. Align crankshaft sprocket timing mark to mark on oil pump housing. Mark on oil pump housing is 60 degrees ATDC of number one cylinder. See Fig. 10

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).