Skip to content

how to remove the rear cover of blu dash 4 5

You search PDF repair manual about how to remove the rear cover of blu dash 4 5, if there are search results will appear below. If search results do not exist, please search by others keyword.

2005 TOYOTA TACOMA PICKUP DASH FRONT DOOR PANEL INSTALLATION MANUAL

download
ANTENNA: THE FACTORY ANTENNA IS LOCATED ATOP THE FRONT PASSENGER FENDER. RADIO REMOVAL AND IN-DASH INSTALLATION: NOTE: THE FACTORY RADIO PROVISION IS A DOUBLE DIN OPENING. 1. USING A PICK TOOL, CAREFULLY POP OUT THE A/C CONTROLS. 2. EXTRACT (4) 10MM BOLTS SECURING THE RADIO TO THE DASH, DISCONNECT AND REMOVE. FRONT DOOR SPEAKER INSTALLATION: NOTE: THE FACTORY SPEAKER PROVISION IS FOR A 6 1/2″ SPEAKER MOUNTED IN A FACTORY ADAPTER. 1. REMOVE “A” TRIM PANEL FROM TOP FRONT CORNER OF DOOR PANEL. 2. EXTRACT (1) PHILLIPS HEAD SCREW FROM DOOR HANDLE. 3. REMOVE ARM REST COVER AND EXTRACT (5) PHILLIPS HEAD SCREWS FROM BEHIND. 4. REMOVE (1) PUSH-TAB FASTENER FROM FRONT UPPER DOOR PANEL NEAR MIRROR. 5. USING A PANEL REMOVAL TOOL, CAREFULLY RELEASE PANEL, LIFT AWAY AND REMOVE. 6. EXTRACT (3) 10MM BOLTS SECURING SPEAKER, LIFT AWAY, DISCONNECT AND REMOVE. REAR SPEAKER INSTALLATION: NOTE: 2-DOOR REGULAR CAB HAS NO FACTORY REAR SPEAKER PROVISION. EXTENDED CAB REAR-SIDE DOOR SPEAKER INSTALLATION: 1. REMOVE (1) PHILLIPS HEAD SCREW FROM DOOR HANDLE, THEN REMOVE HANDLE COVER. 2. REMOVE (1) PHILLIPS FROM ARMREST POCKET. 3. REMOVE (1) POP TAB AT THE TOP OF THE DOOR PANEL. 4. REMOVE (1) 15 MM BOLT SECURING SEAT BELT TO BOTTOM OF THE DOOR. 5. USING A PANEL REMOVAL TOOL, CAREFULLY RELEASE PANEL, LIFT AWAY AND REMOVE. 6. EXTRACT (3) 10MM BOLTS SECURING SPEAKER, LIFT AWAY, DISCONNECT AND REMOVE. 4-DOOR CREW-CAB REAR SIDE DOOR SPEAKER INSTALLATION: 1. REMOVE (1) PHILLIPS HEAD SCREW FROM DOOR RELEASE HANDLE. 2. REMOVE (1) PHILLIPS FROM ARMREST POCKET. 3. REMOVE TRIM PANEL ON REAR SIDE OF WINDOW. 4. REMOVE (1) PUSH-TAP FASTENER EXPOSED IN STEP #3 ABOVE. 5. USING A PANEL REMOVAL TOOL, CAREFULLY RELEASE PANEL, LIFT AWAY, UNPLUG CONNECTORS AND REMOVE. 6. EXTRACT (3) 10MM BOLTS SECURING SPEAKER, LIFT AWAY, DISCONNECT AND REMOVE.

1996 Ford Taurus Transmission and Drivetrain Automatic Transmission/Transaxle Removal and installation Manual

download
REMOVAL NOTE: The oil pump and valve body are removed as an assembly. 1. Disconnect battery ground cable, then remove battery, battery tray, and remote air cleaner. 2. Position supply hoses, vacuum hoses, and wiring away from pump and valve body cover. 3. Remove shift lever. 4. On models equipped with Anti-lock Brake System (ABS) , remove splash shield cover, then disconnect brake reservoir hose and cap to prevent contamination. 5. On all models, remove EGR bracket attaching bolts, then install lifting eye. 6. Remove throttle body bracket attaching bolt, install lifting eye, then using suitable equipment support engine. 7. Remove lefthand transaxle mount. 8. Remove transaxle side pan upper attaching bolts. 9. Raise and support vehicle. 10. Remove lefthand front wheel and tire assembly. 11. Remove inner fender cover and position aside, then disconnect ride height sensor. 12. Remove rear transaxle mount attaching bolt. 13. Loosen but do not remove two lefthand subframe attaching bolts. 14. Remove two engine support mount attaching bolts. 15. Remove four lefthand engine support attaching bolts, then remove the engine support. 16. Position suitable drain pan, then remove remaining transaxle side pan attaching bolts and remove pan. 17. Using suitable screwdriver, place manual shift shaft in Park position. 18. Disconnect upper bulkhead electrical connector wiring retainer clip from valve body. 19. Disconnect electrical connectors 20. Remove valve body attaching bolts, then disengage linkage and remove valve body. NOTE: Do not remove oil pump cover attaching bolts. INSTALLATION 1. Install new pump and valve body to chain cover gasket. 2. Slide pump and valve body onto pump shaft. 3. Rotate pump and valve body assembly toward dash panel, then engage manual valve link with manual valve. 4. Slightly rotate pump and valve body assembly to engage oil pump shaft splines with oil pump rotor splines. Valve body should slide flush with chain cover. A suitable 7/8 inch deep well socket on crankshaft pulley may be required for complete engagement. 5. On models less anti-skid, if engagement is not as indicated in step 4, proceed as follows: a. Remove manual valve from valve body. b. Rotate assembly to allow full engagement, up to 360° . c. After full engagement, return assembly to installed position, then install manual valve. Zoom Sized for Print Oil Pump And Valve Body Bolt Tightening Sequence

2007-2008 Toyota Tundra Crew Cab Installation Manual

download
1. Cover the front seats, floorboards, dash and steering wheel with a clean drop cloth or disposable plastic covers. Note: Always wear eye and hand protection when working with glass. Make sure that you have the right glass and the urethane systems are current. Windshield part numbers are FW02724, FW02723, FW02722 or FW02721. 2. Remove the rearview mirror by loosening the Tork screw using a T-20 Tork screwdriver. Slide the wire-harness trim cover off the headliner. Slide the mirror off the mirror bracket in an upward motion. 3. Disconnect the wire harness from the underside of the hardware with a small flat-tip screwdriver or your fingernails. 4. Remove the windshield-wiper nuts using a wrench or socket. If the nuts are tight, loosen them with a 14-millimeter wrench and then come back with your socket. Move the wiper arm in an up-and-down motion to break it loose from the post, or use a wiper puller. Caution: Wipers can sometimes be hard to remove. To avoid stressing the post, use a wiper puller. The wipers are marked; take note to ensure proper re-installation. 5. Using a No. 2 Phillips-tip screwdriver, remove the two plastic screw inserts on the fasteners located on the outer edge of the cowling corners. There is one on the passenger’s side and one on the driver’s side. A5a A5b 2007-08 Toyota Tundra Crew Cab By Gilbert R. Gutierrez Vehicle type: Four-door, crew-cab pickup truck NAGS numbers*: Windshield part numbers are FW02724, FW02723, FW02722 or FW02721; front door glass FD23323- 24 R-L; rear door glass FD23325-26 R-L; and back glass FY95054, FY95053, FB23336, FB23335 and FB23334. Helpful tools or supplies: Retention tape or a rubber hose to protect the fenders and hood; a PryBaby for molding and panel removal. Watch for: Be careful not to pull too hard on the rearview mirror harness during removal to avoid ripping the headliner. When removing or re-installing the A-pillar trim panels, take care to avoid disturbing the curtain air-bag harness. *With permission from National Auto Glass Specifications. Call NAGS at 800/551-4012 or visit www.nags.com. Vehicle information A1 A2 A3a A3b A4a A4b 35 6. Remove the rubber corner pieces from the corners of the cowling at the base of the windshield. Using an outward motion, pull out the rubber piece, and then gently pull the rubber insert from the cowling. 7. With the hood open, push in and pop loose the six plastic tab fasteners using a No. 1 PryBaby tool from the underside. There are three on the passenger’s side and three on the driver’s side, with a guide pin at the center. 8. Remove the two-part cowl by sliding it in an upward-outward motion toward the engine compartment, disengaging the eight underside tabs on the front part of the cowling from the base of the windshield. Tape the hood and fender with molding-retention tape to avoid gnarling or scratching the cowling. Note: When re-installing the cowling, use a No. 1 PryBaby tool to assist in the installation of the cowling onto the bottom of the windshield. 9. If using a cold knife or power tool to cut out the glass, remove the A-pillar trim panels, as the windshield fits close to the pinchweld. 10. Remove the door weatherstrip. 11. Remove the screw covers using a No. 2 PryBaby. 12. Remove the two 10-millimeter bolts hidden beneath the covers using a 10-millimeter socket-wrench driver. Pull the handle loose. 13. Remove the A-pillar trim panels using a door-panel remover or No. 2 PryBaby tool. Caution: Be careful not to dis- A6a A6b A6c A7a A11a A11b A12a A12b A7b A7c A8 A10 A13a A13b 36 AutoGlass™ •March/April 2008 Installation ? F or T echnicians Only turb the curtain air-bag harness when removing or re-installing the A-pillar trim panels. Note: Before beginning windshield removal, verify the new windshield is the correct one and the urethanes and primers are current. Never use outdated products as this could jeopardize the structural integrity of the vehicle and the safety of its passengers. Removal 14. Make sure cutting blades are sufficiently sharp. 15. Before cutting out the windshield, remove contaminants from the glass and pinchweld to prevent contact with the urethane. 16. If using a cold knife, use a 3? 4 -inch blade. Cut three sides; then use a long knife or power tool to cut the bottom of the windshield. Note: There are no gravity stops on this windshield. 17. If trying to save the windshield, use an Equalizer with an 8-inch blade. Note: When using any power tool, lubricate the cutting area with water. Spray the top and sides; then make your cuts. 18. After cutting the sides and top, cut out the bottom portion of the glass using an Equalizer Express. Spray the bottom of the windshield with water at least 4-to-5 inches above the urethane on the glass, so the water flows down into the urethane while you make your final cut across the bottom of the windshield. Caution: Never use your head to push, as this could result in back and neck injuries. 19. Take the windshield out of the opening using a set of vacuum cups. Lift the glass and place it on a windshield stand or suitable workstation. Installation 20. After cutting the windshield out, remove contaminants such as dirt, moisture and other debris from the pinchweld. Clean the dashboard. 21. Dry fit the new glass to the opening. Mark your glass using a grease pencil or molding-retention tape. 22. Place your vacuum cups on the windshield in the appropriate location for a one-person set. 23. For driver-side setting of the windshield using a Glass Handler Kit, place the kit’s elbow-setting pad on the driver’s side of the hood area; then lift the windshield from the stand using the vacuum cups. 24. Reach over, place your elbow on the setting pad and set the windshield onto the old urethane. 25. With the windshield resting in the opening, make sure it is in the right spot. 26. Adjust both sides to the correct setting, marking the passenger’s side, then the driver’s side. Lift the glass and place it on a windshield stand or suitable workstation. 27. Follow the urethane manufacturer’s recommendations for installation. 28. Clean the inside of the windshield using a urethane manufacturer-recommended product; follow recommended steps. Note: Do not touch the bonding area of the windshield after cleaning, prepping or priming it. 29. Wear powder-free Nitrile gloves to keep off chemicals. 30. Apply the glass prep and primer, following the urethane manufacturer’s recommendations.

EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide

download
EGOCorp USA 8820 Kenamar Drive, Ste. 506 San Diego, CA 92121 Page 1 ofon should 2 Version 1.3 Phone +1 (858) 566-2159 Fax +1 (858) 566-2179 www.egocorpusa.com EGO DASH TS Bluetooth Hands-Free Car Kit Installation Guide WARNING: We recommend disconnecting the vehicles battery prior to the installation. The installatibe only performed by professional installers. Improper installation may void the vehicles and EGO DASH TS warranty. EGO DASH TS Installation Steps 1. Remove head unit (Consult with owner’s and shop manual) 2. Disconnect factory wiring harness from head unit 3. Connect EGO DASH TS Wiring Harness to the head unit Wiring Harness A Locate
amplifier (Most Lexus ? behind glove box; Toyota Land Cruiser ? under drivers or passengers seat). Connect male and female 16-pin connectors between amplifier and the vehicle’s wiring harness. Connect Yellow Mute wire: Lexus ? pin 7 on the 18-pin connector; Land Cruiser ? pin 3 on the 25-pin connector (amplifier). Connect Blue Ignition wire (male bullet connector): Lexus ? pin 16 on the 16-pin connector (female bullet connector); Land Cruiser ? pin 20 on the 25-pin connector (amplifier). Wiring Harness B The normal location of the mute is pin 4 (x) on the 6-pin connector. However, on some rare factory head units, the mute pin might be pin 5. The mute pin on the head unit should show ~ 5 volts when the head unit is turned on. Wiring Harness C Connect the male and female ISO connectors, if they are not already connected. Splice the gray wires (only!) into the loudspeaker wiring, going from the amplifier to the center or door loudspeaker. The 2 female bullet connectors go to the loudspeaker. The 2 male bullet connectors go to the amplifier. The 4 white wires are not used! Connect the yellow mute (“Mute Signal”) cable (male bullet connector) on the ISO Harness coming from the EGO DASH TS brain to “Mute 2″ (white cable – female bullet connector), if not already connected. Wiring Harness D Please contact EGO Technical Support at (858) 566-2170 (9AM-5PM PST) or support@egohandsfree.com . 4. Connect EGO DASH TS Wiring Harness to the vehicle’s wiring harness (One or more of the connectors might be not used, depending on the vehicle’s configuration) 5. Connect the EGO DASH TS Wiring Harness to the EGO DASH TS control box (16pin Molex) 6. Install the EGO DASH TS switch insert into the desired location (knockout) 7. Connect the EGO DASH TS switch with the EGO DASH TS box (Use the included extension cable if necessary) 8. Install the EGO Microphone into the desired location (e.g. the rear view mirror. DO NOT install the microphone on or near vehicles’ safety systems, like the airbag) 9. Test the EGO DASH TS: a. Reconnect the battery and turn on the ignition of the vehicle b. Pair a Bluetooth mobile phone with the EGO DASH TS (Pin code: “0000″) c. Turn on the head unit and select a radio station; Make sure you can hear the radio through the cars’ speakers; Adjust audio volume if necessary

2001 Toyota Highlander Sport Utility, Radio, FRONT DOOR SPEAKER INSTALLATION MANUAL

download
2001 Toyota Highlander Sport Utility PRELIMINARY: Disconnect the negative battery cable. ANTENNA: The factory antenna is located atop the right front fender panel. RADIO REMOVAL AND IN-DASH INSTALLATION: Note: The factory radio provision is for a Double ISO/DIN style radio. An installation kit is required when installing an aftermarket stereo. 1. Using panel removal tool carefully pry off radio bezel. 2. Extract (6) 10 mm bolts securing radio and climate controls in dash, disconnect and remove. 3. Extract (8) Iso screws securing radio to bracket. 4. Extract (2) Philips screws securing bracket to bezel, pull away and remove radio. FRONT DOOR SPEAKER INSTALLATION: Note: The factory speaker provision is for a 1 ½” tweeter and a 6 ½” 3-Hole speaker mounted to a factory speaker adapter. 1. Remove screw cover from door opener cup and exract (1) Philips head screw, pry bezel out then forward to remove. 2. Remove inside mirror cover. 3. Pry out door cup and extract (1) Philips screw from beneath. 4. Exract (1) plastic fastener from front top portion of door. 5. Pry off door panel, pull away, disconnect, and remove. 6. Extract (3) 10 mm bolts securing speaker, pull away, disconnect, and remove. REAR DOOR SPEAKER INSTALLATION: Note: The factory speaker provision is for a 5 ¼” 3-Hole speaker mounted in a factory speaker adapter. 1. Remove screw cover from door opener cup and extract (1) Philips head screw, pry bezel out then forward to remove. 2. Pry out door cup and extract (1) Philips screw from beneath. 3. Pry off door panel, pull away, disconnect and remove. 4. Extract (3) 10 mm bolts securing speaker , pull away, disconnect, and remove