Skip to content

how to remove the timing belt on daewoo lanos 2000

You search PDF repair manual about how to remove the timing belt on daewoo lanos 2000, if there are search results will appear below. If search results do not exist, please search by others keyword.

1999 Daewoo Lanos SE TIMING BELT REMOVAL And INSTALLATION MANUAL

download
TIMING BELT Removal 1. Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove the air filter housing. 2. Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove accessory drive belts. See Fig. 1 . 3. Remove power steering pump pulley bolts (if equipped). Remove power steering pump pulley. Remove crankshaft pulley center bolt. Remove crankshaft pulley. Lower vehicle. 4. Remove upper and lower timing belt covers. See Fig. 2 . Remove power steering pump mount bolts (if equipped). Set power steering pump aside with hoses attached. 5. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine). 6. Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 3 . Ensure camshaft sprocket timing marks face each other. See Fig. 4 . 7. Slightly loosen water pump bolts. Using Timing Belt Adjuster (J-42492), rotate water pump counterclockwise to relieve tension on the timing belt. See Fig. 5 . Remove timing belt

2001 Daewoo Leganza SE TIMING BELT REMOVAL And INSTALLATION Manual

download
TIMING BELT Removal 1. Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing. 2. Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt. 3. Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle. 4. Support engine assembly from above with Support Fixture (J-28467-B). See Fig. 1 . Remove engine mount bracket from timing belt end of engine. See Fig. 2 . 5. Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. See Fig. 3 . Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine). 6. Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 . 7. Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. See Fig. 6 . Remove timing belt Fig. 6: Identifying Timing Belt Tensioner Courtesy of DAEWOO MOTOR AMERICA, INC. Installation 1. Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS . 2. Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch. 3. If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt. 4. Install right front splash shield. Install right front wheel. Install air filter housing and resonator.

2000 Cadillac Catera Timing Belt Service and Repair Manual

download
Timing Belt Replacement TIMING BELT REPLACEMENT Removal Procedure ^ Tools Required -J 42069 Timing Belt Alignment Kit -J 42098 Crank Hub Torx Socket Notice: Failure to follow the described timing belt inspection and maintenance may result in a broken timing belt and cause severe engine damage. 1.Inspect the cold start counter (also called a heavy duty register) with a scan tool. If there are any cold starts (below -28° C or -20° F) visually inspect the timing belt for cracks. It cracks are noted, do not reuse the belt. Replace the belt and clear the cold start counter. If the belt is okay, and is reused, do not clear the cold start counter. 2.Remove the intake air resonator. Refer to Intake Air Resonator Replacement in Powertrain Management. 3.Remove the intake plenum. Refer to Intake Plenum Replacement. 4.Remove the timing belt cover. Refer to Timing Belt Cover Replacement. 5.Remove the crankshaft balancer bolts. 6.Remove the crankshaft balancer from the crankshaft sprocket. 7.Rotate the crankshaft clockwise to 60 degrees Before Top Dead Center (BTDC) 8.Install the J 42069-10 to the crankshaft sprocket with the knurled bolt. 9.Use the J 42098 to carefully turn the crankshaft in the engine rotational direction (clockwise) until the lever of the J 42069-10 firmly contacts the water pump pulley flange. 10.Secure the moveable lever of the tool to the water pump pulley flange. Important: Ensure that the crankshaft is not 180 degrees off TDC. The reference marks on the camshaft gears should be aligned with the corresponding notches on the rear timing belt cover at this point. If they are not aligned, the engine is 180 degrees off. 11.Install the J 42069-1 and the J 42069-2 to the camshaft gears. If the J 42069-1 or the J 42069-2 do not fit into the teeth of the camshaft gears, it may be necessary to loosen the relevant timing belt idler pulley and turn the cam until the J 42069-1 or the J 42069-2 can be inserted. Notice: After timing belt is removed, never turn camshaft and crankshaft independently. If turned, interference may occur among pistons and valves, and parts related to pistons and valves may be damaged. 12.Loosen the timing belt tensioner and idler pulleys. Important: Do not remove J 42069-1 and the J 42069-2 while the belt is removed. 13.Remove the timing belt. Installation and Initial Adjustment Procedure ^ Tools Required -J 42069 Timing Belt Alignment Kit -J 42098 Crank Hub Torx Socket

1999 Subaru Forester S TIMING BELT REPLACEMENT MANUAL

download
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove engine under cover. 2. Lower vehicle. Remove radiator coolant reservoir, and set aside. Remove electric cooling fan and radiator shroud. 3. On Impreza and Forester, remove accessory drive belt cover. On all models, remove accessory drive belts. 4. Hold crankshaft pulley stationary, and remove crankshaft pulley center bolt. Remove crankshaft pulley. Remove timing belt covers. 5. Turn crankshaft to align crankshaft and camshaft timing notches with marks on rear timing cover and engine block. See Fig. 1 and Fig. 2 . On manual transmission models, remove timing belt guide from top of crankshaft pulley. 6. On all models, if reusing old belt, use White paint to mark timing belt in relation to sprocket timing marks. See Fig. 3 . Also mark timing belt direction of travel. On 2000 and newer vehicles, count number of teeth between marks. For correct count, see INSTALLATION MARK MEASUREMENT SPECIFICATIONS table. 7. Remove No. 2 timing belt idler pulley. See Fig. 4 . Remove timing belt. Remove timing belt automatic tensioner with rod facing up. INSTALLATION MARK MEASUREMENT SPECIFICATIONS Tips Click a link to view tip Eric O. Tip: Timing Belt – R&R Tech1 Tip: interference engine – ’01 2.5L Tips Click a link to view tip Tech1 Tip: INTERFERENCE MOTOR Application (1) Number Of Teeth Baja

2003 Kia Optima L4-2.4L Timing Belt Service and Repair Manual

download
3.Turn the crankshaft clockwise and align the timing marks so as to bring the No.1 cylinder to compression top-dead-center position. At this time the timing marks of the camshaft sprocket and the upper surface of the rocker cover should coincide, and the dowel pin of the camshaft sprocket should be at the upper side. Remove the auto tensioner. CAUTION: Rotate the crankshaft clockwise. 4.Remove the timing belt. NOTE: If the timing belt is reused, make an arrow mark indicating the turning direction (or the front of the engine) to make sure that the belt is reinstalled in the same direction as before 6.When the oil pump sprocket nut is removed, first remove the plug at left side of the cylinder block and insert a screwdriver to check the left counter balance shaft in position. Screwdriver used for this purpose should have a shaft 8 mm (0.3 inch) in diameter which can be inserted more than 60 mm (2.36 inch) 7.Remove the oil pump sprocket retaining nut and remove the oil pump sprocket. 8.Loosen the right counter balance shaft sprocket mounting bolt until it can be loosened by hand. 9.Next, remove tensioner “B” and remove timing belt “B”. CAUTION: After timing belt “B” has been removed, do not attempt to loosen bolt while holding sprocket with pliers, etc. 10.Remove the crankshaft sprocket “B” from crankshaft. INSPECTION Sprockets, Tensioner Pulley, and Idler Pulley 1.Check the camshaft sprocket, crankshaft sprocket, tensioner pulley, and idler pulley for abnormal wear, cracks, or damage. Replace as necessary. 2.Inspect the tensioner pulley and the idler pulley for easy and smooth pulley rotation and check for play or noise. Replace as necessary. 3.Replace if there is grease leak