Skip to content

how to remove turn signal lever 1986 monte carlo

You search PDF repair manual about how to remove turn signal lever 1986 monte carlo, if there are search results will appear below. If search results do not exist, please search by others keyword.

2003 Chevrolet Impala LS MULTIFUNCTION TURN SIGNAL SWITCH REPLACEMENT

download
1. Disable the SIR system. Refer to SIR Disabling and Enabling Zone 3 in SIR. 2. Remove the upper and lower trim covers. Refer to Steering Column Trim Covers Replacement . 3. Remove the wire harness assembly (1) from the wire harness strap (2). 4. Disconnect the turn signal and multifunction switch assembly connector from the SIR system coil connector. 5. Slide the 2 connectors (2) of the turn signal and multifunction switch assembly out of the bulkhead connector (1) 6. Remove the 2 pan head tapping screws (1) and (3) from the turn signal and multifunction switch assembly (2). 7. Remove the turn signal and multifunction switch assembly (2) from the steering column tilt head assembly. 1. Install the turn signal and multifunction switch assembly (2) onto the steering column tilt head assembly. 2. Screw the 2 pan head tapping screws (1) and (3) into the turn signal and multifunction assembly (2). Tighten * Tighten the top pan head tapping screw (1) to 3 N.m (27 lb in). * Tighten the side pan head tapping screw (3) to 7 N.m (62 lb in).

1989 Chevrolet Corvette V8-350 5.7L Steering Column Service and Repair Manual

download
SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE Disassembly 1. Remove steering wheel as follows: a. Disconnect battery ground cable, then remove horn cap from steering wheel by pulling. b. Disconnect horn button wire, then remove telescope lever screws and shaft lock knob screw. c. Remove telescope adjustment lever, steering wheel nut retainer and nut. d. Remove steering wheel with a puller. 2. Remove spacer, bumper, spacer and snap ring retainer (Nos. 2, 3, 4, and 5 in Fig. 59 ). 3. Remove shaft lock retainer using lock plate compressor to depress shaft lock. 4. Remove shaft lock and carrier assembly, upper bearing spring, upper bearing seat and inner race. 5. Reverse procedure to install. TURN SIGNAL SWITCH Disassembly 1. Remove SHAFT LOCK, TURN SIGNAL CANCELLING CAM, UPPER BEARING SPRING, UPPER BEARING SEAT & INNER RACE as previously outlined. 2. Place turn signal lever to the right turn position, then remove screw and switch actuator pivot assembly (Nos. 11 and 44 in Fig. 59 ). 3. Remove the screws and the wiring protector (Nos. 10 and 45). 4. Remove turn signal switch, then gently pull wire harness through column housing shroud, column housing and lock housing cover. 5. Reverse procedure to install, noting the following: a. Torque turn signal switch screws (No. 10 in Fig. 59 ) to 27 inch lbs. and torque screw (No. 11) to 18 inch lbs. BUZZER SWITCH ASSEMBLY & STEERING COLUMN LOCK CYLINDER SET

1988 Cadillac DeVille Steering Column Service and Repair Manual

download
Disassembly 1. Remove dash panel bracket and store bracket in a safe place to prevent damage to mounting capsules. 2. Place column in a vise using both weld nuts of either set A or B, Fig. 29. The vise jaws must clamp onto the sides of weld nuts indicated by arrows shown on set B. Do not place column in vise by clamping onto only one weld nut, by clamping on one weld nut of both sets A and B or by clamping onto the sides not indicated by arrows, as damage to column could result. 3. Inspect steering shaft to determine type of thread used for steering shaft nut. Metric type shafts can be identified by a groove located in area of steering wheel locating splines, while shafts with American type threads do not have this groove. If shaft has metric type threads, the forcing screw of Lock Plate Compressor Tool J-23653 must be removed and replaced with the metric forcing screw J-23653-4 before installing lock plate compressor tool on steering shaft. Compress lock plate using lock plate compressor tool, then pry snap ring from shaft groove and discard wing. Remove lock plate compressor tool and lock plate. 4. Remove directional signal switch, lock cylinder and ignition key warning switch, then remove steering shaft from lower end of column. 5. On power steering columns, remove steering shaft lower bearing from plastic adapter at lower end of column. 6. Remove four turn signal housing to column jacket retaining screws and remove housing and shroud assembly. 7. Remove three shroud to signal housing retaining screws and remove shroud. 8. Using hand as shield to prevent lock inhibitor lever spring wire from flying out, remove lock inhibitor lever and spring wire. 9. Lift ignition switch actuating rod, rack assembly, shaft lock bolt and spring assembly from housing, then if necessary, remove rack preload spring. 10. Remove ignition switch actuator sector through lock cylinder hole by pushing firmly on block tooth of sector with a blunt punch or screwdriver.

1994 Ford Truck F 350 2WD Pickup A/T – E40D No Upshifts or Harsh Upshifts/ 4th Gear Starts

download
All of these concerns can be the result of an inappropriate Manual Lever Position (MLP) sensor signal. The MLP sensor consists of six resistors connected in series (ganged). The resistance of the MLP sensor will vary based on which range the transmission is in. The MLP circuit can be checked using the following steps. (Step 1) Check the MLPS ground: Turn the ignition on. The voltage on pin 46 (sensor ground ) should not exceed .1v. If the voltage is excessive, add an additional ground to the existing ground wire (figure 2). Figure 2 Splice an additional ground from the existing ground wire to a known good ground.The negative post of the battery is the best. This view is of the pins of the MLP connector pins. (Step 2) Check the MLPS voltage: The voltage at pin 30 should vary-in increments- according to the position of the manual lever (figure 3). MLP voltage (ignition on) should be within 20% of these specifications Note It is recommended that you use a break-out box. If a break-out box is not available, you will need to pierce the wires to pins 30 and 46 for these tests. (Step 3) Check the resistance of the MLPS: The resistance of the MLPS (pins 30 and 46) should change-in increments-with the position of the manual lever (figure 4). Note If this test is being done with a break-out box, disconnect the computer first (make sure the ignition is off). If this test is being done without a break-out box, disconnect the MLPS from the vehicle harness. REVISED This is a revised bulletin. Remove bulletin 230 from your files. Note Testing beyond this point will include tests of the harness. Consult the appropriate repair manual for this.

1995-1999 TOYOTA TACOMA BODY LIFT KIT INSTALLATION INSTRUCTIONS

download
1. Read all warnings and instructions completely and carefully before you begin. Check the kit for proper contents (refer to the part’s list and the picture diagrams). NOTE: This kit is designed to fit Tacoma models only, 95 1/2 -97 models equipped with air conditions will require modification to the low pressure A/C line at the firewall. It will need to be bent or in some cases the line may need to be lengthened. The vehicle will need to be taken to a certified A/C service technician to have the system evacuated. The line can then be lengthened between four and five inches. It is crucial that the procedure is done properly to avoid damage to the A/C system. If at anytime during the installation you encounter something different from what is outlined in the instructions, call technical support. (928) 636-7080. www.PerformanceAccessories.com . 2. Park the vehicle on a clean, dry, flat, level surface. Block the tires so the vehicle cannot roll in either direction. WARNING The Supplemental Restraint System (SRS, or air bag) must be deactivated during lift kit installation to avoid accidental air bag deployment while working near SRS sensors and wiring. Do not allow anyone near the air bag during lift kit installation. Accidental deployment can result in serious personal injury or death. Refer to your factory service manual/owner’s manual for the recommended procedure to disable the SRS. The SRS must be reactivated before driving the vehicle. 3. Disconnect both battery cables. Be sure to disconnect the negative cable first, then the positive cable. Remove the airbag fuse from the fuse box. 4. Remove the wire loom that runs from under the alternator to the battery from the mounting brackets. One bracket is on top of the frame. The other bracket is on the fender well. The plastic mounting-collar will slide off the bracket by pushing on the tab on the collar. 5. Remove the fuse that controls the air bag system from the fuse box (refer to the owners manual for the exact location). 6. Remove the ground wire that runs from the back of the engine to the top of the firewall. Remove the wire loom from the mounting bracket on the firewall. Remove the bracket from the firewall. Turn the bracket upside down. Insert the mounting bolt through the ground wire removed from the firewall, Then through the bracket. Tighten securely. Reinstall the bolt that mounted the ground wire to the firewall. Tighten the bolt securely. Do not attach the wire loom at this time. 7. Gently pull out the plastic clips that mount the front fender well skirts to the frame. NOTE: Be very careful with the plastic clips. They will break easily. 8. 4 wheel drive models only. Remove the front axle vent hose from the mounting bracket on the driver’s side fender well. The hose should remain in the frame bracket. 9. Remove the vacuum hose from the bracket that holds it to the drivers side fenderwell. This should allow enough slack to not damage the hose during lifting. 10. Remove the front bumper. Remove the light bulbs and wires from the light housings on each side of the bumper. There are two holes in the fender wells to access the outside bumper mounting bolts. Remove the nuts that mount the outside of the bumper to the body. Remove the bolts that mount the bumper to each side of the frame. Remove the bumper from the vehicle. 11. Remove the grill assembly. Remove the turn signal housing from the body. Disconnect the wiring attached to the housing. The grill is mounted to plastic tabs that have a lever in the middle. This lever is locked into place when the grill is mounted. To remove the grill, unlock the tabs and slide the grill off. Be sure that all of the mounting tabs are released before attempting to remove the grill