Skip to content

how to remove upper intake manifold on a 2001 chevy blazer

You search PDF repair manual about how to remove upper intake manifold on a 2001 chevy blazer, if there are search results will appear below. If search results do not exist, please search by others keyword.

2001 Chevy Truck S10/ T10 Blazer Intake Manifold Replacement (Upper) Removal And Installation Manual

download
Intake Manifold Replacement (Upper) Notes Intake Manifold Replacement – Upper Removal Procedure Important: The upper intake does not have to be removed to remove the lower intake manifold. 1. Disconnect the breather tube at the air cleaner outlet duct 2. Remove the air cleaner outlet duct retaining wingnut. 3. Disconnect the IAT sensor harness connector 4. Remove the air cleaner outlet duct from the throttle body. 5. Disconnect the accelerator cable from the throttle body 6. Remove the accelerator cable from the accelerator control cable bracket. 7. Disconnect the cruise control cable, if equipped from the throttle shaft and the accelerator cable bracket. 8. Disconnect the vacuum hose from the intake manifold for the vacuum tank. 9. Remove the power brake booster vacuum hose. 10. Disconnect the following electrical connectors: * The A/C compressor clutch (1) * The A/C compressor cutoff switch (5), if equipped * The Throttle Position (TP) sensor (2) * The Idle Air Control (IAC) motor (3) 11. Disconnect the following electrical connectors: * The fuel meter body assembly (1) * The Manifold Absolute Pressure (MAP) sensor(3) * The EVAP canister purge solenoid valve (2) 12. Remove the engine wire harness clip from the accelerator cable bracket. 13. Move the engine wiring harness aside. 14. Remove the accelerator cable bracket from the throttle body and the intake manifold. 15. Remove the accelerator and cruise control cable bracket from the throttle body. Leave the accelerator and cruise control cables on the bracket16. Remove the PCV valve hose assembly from the intake manifold and the valve rocker arm cover. 17. Remove the bracket for the engine wiring harness from the intake manifold stud. 18. Remove the fuel lines from the fuel meter body assembly. 19. Remove the EVAP canister purge solenoid valve.

2001 Lincoln LS Intake Manifold Upper Removal And Installation Manual

download
Intake Manifold — Upper Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01. 2. Drain the engine cooling system. For additional information, refer to Section 303-03 . 3. Remove the engine appearance cover. 4. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 . 5. Disconnect the throttle position (TP) sensor and the idle air control (IAC) solenoid electrical connectors. 6. Disconnect the accelerator and speed control cables. 7. Remove the cable bracket. 1. Remove the bolts. 2. Remove the bracket. 8. Disconnect the throttle body hoses. 1. Disconnect the coolant hoses. 2. Disconnect the positive crankcase ventilation (PCV) hose. 3. Disconnect the vapor purge hose. 9. Disconnect the vacuum hose. 10. Disconnect the EGR to exhaust manifold tube nut. 11. Remove the cowl vent screen. For additional information, refer to Section 501-02 . 12. Remove the brace. 13. Remove the vacuum hoses from the mounting bracket. 14. Remove the bracket and position the accelerator and cruise control cables aside. 15. Disconnect the differential pressure feedback EGR electrical connector. 16. Remove the stud and nut and position the differential pressure feedback EGR transducer aside. 7. Remove the fuel pressure sensor shield. 1. Remove the nut. 2. Remove the bolts. 3. Remove the shield. 18. Disconnect the vacuum hose from the rear of the upper intake manifold. 19. Disconnect the intake manifold tuning valve (IMTV) electrical connector. 20. Disconnect the exhaust vacuum regulator (EVR). 1. Disconnect the electrical connector. 2. Disconnect the vacuum line. 21. Remove the upper intake support bolt. 22. Remove the front intake manifold support bolt.

1997 Ford Explorer/ Mountaineer Intake Manifold Upper Repair Manual

download
Intake Manifold — Upper 1. Disconnect the battery ground cable. 2. Remove the air cleaner outlet tube; refer to Section 303-12 3. Disconnect the ignition coil electrical connector and the noise suppressor electrical connector. 4. Disconnect the idle air control (IAC) electrical connector. 5. Disconnect the EGR backpressure transducer electrical connector. 6. Disconnect the EVR solenoid electrical and vacuum connectors. 7. Disconnect the brake booster vacuum hose from the upper intake manifold. 8. Disconnect the vacuum connector from the upper intake manifold 9. Disconnect the vacuum connector from the fuel pressure regulator and remove the vacuum harness from the engine. 10. Disconnect the throttle position (TP) sensor electrical connector. 11. Disconnect the hoses from the EGR backpressure transducer ports. 12. Disconnect the six spark plug wires from the spark plugs. 13. Disconnect the spark plug wires from the seven retaining clips. 14. Remove the four ignition coil bolts and the ignition coil from the upper intake manifold. 15. Raise and support the vehicle; refer to Section 100-02 . 16. Access the LH exhaust manifold through the wheel well and disconnect the EGR inlet tube from the exhaust manifold (9430). 17. Lower the vehicle. 18. Disconnect the EGR inlet tube from the EGR valve and remove the EGR inlet tube. 19. Remove the EGR valve bolts and the EGR valve and gasket. 20. Remove the oil level indicator tube bracket nut and remove the oil level indicator tube (6754). 21. Remove the EGR outlet tube bracket stud bolt and remove the EGR outlet tube from the upper intake manifold. 22. Disconnect the accelerator cable assembly from the upper intake manifold bracket. 23. Remove the upper intake manifold nuts and remove the upper intake manifold and gasket. Installation 1. NOTE: Before installing the upper intake manifold, the EGR port must be clean and free of obstruction. Use combustion chamber cleaner and a suitable wire brush to remove carbon buildup from the EGR passages. Clean and inspect all surfaces. Install new seals and new gaskets. Use Metal Surface Cleaner F4AZ-19A536-RA or equivalent meeting Ford specification WSE-M5B392-A to clean the upper and lower intake manifold gasket surfaces. Position the upper intake manifold gasket on the fuel injection supply manifold. 2. Position the upper intake manifold and install the six nuts.

2002 Mercury Sable Upper Intake Manifold Removal And Installation Manual

download
Upper Intake Manifold Removal 1. Remove the air cleaner outlet tube. 2. Remove the pin-type retainers and the accelerator cable splash shield 3. Disconnect the throttle cable and the cruise control cable. 4. Disconnect the Throttle Position Sensor (TPS) and Idle Air Control (IAC) valve electrical connectors. 5. Disconnect the harness Tom the throttle body stud. 6. Disconnect the Exhaust Gas Recirculation (EGR) vacuum regulator and vacuum supply hoses. 7. Disconnect the Positive Crankcase Ventilation (PCV) and Evaporative Emissions (EVAP) vacuum hoses. 8. Remove the EGR valve. 9. Remove the EGR Vacuum Regulator (EVR) valve. Zoom Sized for Print 1 Disconnect the vacuum hose. 2 Remove the nuts. 3 Remove the bolts. 4 Remove the EGR valve. Zoom Sized for Print 1 Disconnect the vacuum hose. 2 Disconnect the electrical connector. 3 Remove the bolts. 4 Remove the valve 10. Remove the eight bolts and the upper intake manifold. * Remove and discard the gaskets. * Clean all mating surfaces. Installation 1. Position new gaskets in the upper intake manifold. 2. Position the upper intake manifold and install the bolts in the sequence shown. 3. Install the EGR vacuum regulator valve. 4. Install the EGR valve. Zoom Sized for Print 1 Position the valve. 2 Install the bolts. 3 Connect the electrical connector. 4 Connect the vacuum hose. Zoom Sized for Print 1 Position the EGR. 2 Install the bolts. 3 Install the nuts 4 Connect the vacuum hose

2006 Ford Five Hundred SE UPPER INTAKE MANIFOLD REMOVAL AND INSTALLATION MANUAL

download
Removal All vehicles 1. Drain the cooling system. For additional information, refer to DRAINING . 2. Disconnect the battery ground cable. For additional information, refer to REMOVAL AND INSTALLATION . 3. Remove the air cleaner outlet pipe. For additional information, refer to REMOVAL AND INSTALLATION . 4. Remove the 4 transaxle roll restrictor cross brace bolts 5. Remove the bolt and the transaxle roll restrictor cross brace. 6. Disconnect the evaporative emissions (EVAP) canister purge valve tube from the upper intake manifold and detach the retainer. 7. Disconnect the positive crankcase ventilation (PCV), brake booster and vacuum harness tubes from the upper intake manifold. 8. Detach the fuel tube retainer from the upper intake manifold. 9. Disconnect the exhaust gas recirculation (EGR) system module electrical connector and vacuum tube. 10. Detach the vacuum tube from the upper intake manifold vacuum tube retainer. 11. Disconnect the EGR system module tube from the EGR system module. Early build 12. Disconnect and plug the throttle body and PCV coolant hoses. Late build 13. Disconnect and plug the 2 PCV coolant hoses. All vehicles 14. Disconnect the throttle body electrical connector. 15. If equipped, remove and discard the 4 upper-to-lower intake manifold screws. 16. Remove the 8 bolts and the upper intake manifold. * Remove and discard the gaskets. Installation All vehicles Fig. 4: Identifying Tightening Sequence Of Bolts Courtesy of FORD MOTOR CO. NOTE: Clean and inspect all sealing surfaces. Install new gaskets 1. Position the upper intake manifold and install the 8 bolts. * Tighten in the sequence shown to 10 N.m (89 lb-in). 2. Connect the throttle body electrical connector. Late build 3. Connect the 2 PCV coolant hoses. Early build 4. Connect the throttle body and PCV coolant hoses. All vehicle 5. Connect the EGR system module tube to the EGR system module. * Tighten to 40 N.m (30 lb-ft). 6. Attach the vacuum tube to the upper intake manifold vacuum tube retainer. 7. Connect the EGR system module electrical connector and vacuum tube. 8. Attach the fuel tube retainer to the upper intake manifold. 9. Connect the PCV, brake booster and vacuum harness tubes to the upper intake manifold. 10. Connect the EVAP canister purge valve tube to the upper intake manifold and attach the retainer. 11. Clean the 4 transaxle roll restrictor cross brace bolts using a wire brush and apply new threadlock to the threads. 12. Position the transaxle roll restrictor cross brace and install the 4 new bolts. * Tighten to 55 N.m (41 lb-ft). 13. Clean the transaxle roll restrictor cross brace-to-roll restrictor bolt using a wire brush and apply new threadlock to the threads. 14. Install a new transaxle roll restrictor cross brace-to-roll restrictor bolt. * Tighten to 48 N.m (35 lb-ft). 15. Install the air cleaner outlet pipe. For additional information, refer to REMOVAL AND INSTALLATION . 16. Connect the battery ground cable. For additional information, refer to REMOVAL AND INSTALLATION . 17. Fill and bleed the cooling system.