how to repair kancil 850 carburetor

You search PDF repair manual about how to repair kancil 850 carburetor, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to repair kancil 850 carburetor Direct Download speed 5432 Kb/s

  how to repair kancil 850 carburetor Full Version speed 8172 Kb/s



2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration Repair Manual

0

Filed Under (Toyota Manuals) by admin on 30-05-2012

download
Harsh 5-4 Downshift on Deceleration Repair Procedure 1. Test drive and verify that the 5-4 harsh downshift condition occurs as described in the Introduction section in this TSB. 2. Replace the SLT solenoid assembly. Refer to the Technical Information System (TIS): •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” •2007 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2008 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2009 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” NOTE For SLTsolenoid identification, refer to TSB No. TC 007-05, “U250E Transmission Solenoid Identification”. 3. Reinstall the automatic transaxle oil pan. Refer to TIS: •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” • 2007 / 2008 / 2009 model year Camry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Installation” 4. Test drive and verify that the A TM operates normally

Related Content:

manual book kancil 850 pdf, FORD 555D VALVE SETTINGS, 1971 c10 service manual pdf, 1999 chevy S10 - manual, 2006 ford focus ses repair manual, Pontiac Grand-Am 1994-1998 workshop Service Repair Manual download, cft30 scan codes, 95 ford Windstar 3 8 change transmission shifter cable, 5 9 Cummins Service Manual, 5 9 cummins dodge engine service manual for 2006

Toyota CT20 CT20 Type Dynamic and Carbon Seal Repair Parts & Service Kits

0

Filed Under (Toyota Manuals) by admin on 23-06-2011

download
All parts are available for purchase as individual components or in the following popular Repair Kits Key Part number Description Q ty in Turbo 1500 – 320 – 750 1500 – 320 – 751 1500 – 320 – 752 1500 – 320 – 753 1500 – 320 – 754 1500 – 320 – 760 8 1500-320-100 Journal Bearing 2 2 2 2 2 2 2 9 1500-320-290 Bearing Spacer 1 11 1500-320-320 Thrust Bearing 1 1 1 1 1 1 14 1500-320-160 Piston Ring Turbine 1 1 1 1 1 1 1 15 1500-320-170 Piston Ring Compressor 1 1 1 19 1500-320-200 Thrust Collar 1 1 1 1 1 21 1500-320-220 Thrust Spacer Carbon 1 1 1 1 22 1500-320-221 Thrust Flinger Dynamic 1 1 24 1500-326-145 Seal Plate Retaining Ring 1 28 1500-320-310 Oil Deflector 1 29 1500-320-150 O Ring (Seal Plate) 1 1 1 1 1 1 1 30 1500-320-155 O Ring (CT20 C/Cover) 1 1 1 1 1 1 1 30 1500-320-156 O Ring (CT20 C/Cover) 1 1 1 33 1500-320-300 Seal Plate Assy Carbon 6.1mm Depth 1 1 1 1 34 1500-320-301 Seal Plate Assy Dynamic 1 1 34 1500-320-302 Seal Plate Assy Carbon 7.57mm Depth (for turbo 54030) 1 1 43 1500-320-351 Shaft Nut LHT 1 1 1 1 1 1 1 – 1500-320-790 Gasket CT20 Oil Inlet / outlet 1 1 1 1 1 1 1 – 1500-320-791 Gasket CT20 Water Inlet / Outlet 2 2 2 2 2 2 2 Description of Repair Kits available 1500-320-750 Repair Kit (Minor) CT20 Dynamic 1500-320-751 Repair Kit (Minor) CT20 Carbon Seal 1500-320-752 Repair Kit (Major) CT20 Carbon Seal 1500-320-753 Repair Kit (Major) CT20 Dynamic 1500-320-754 Repair Kit (Major) CT20 Carbon Seal (54030 Only) 1500-320-760 Repair Kit CT20 (Carbon Seal – No thrust bearing Notes: 1) CT20 and CT26 repair kits are identical except for the Comp Cover O-ring – USE 1500-326-754 kit to repair both CT20/CT26 dynamic models from one kit. 2) For Pre 1990 CT20 Landcruiser 2.4L (17201-54030), the seal plate flange is deeper ( Part No. 1500-320- 302 ) and the O-ring groove is Ø114mm in the comp cover rather than Bearing housing. Use kit 1500-320- 754. Version 7.0 CT20 Type Oversize Repair Parts Available Journal Bearings CT20/26 Standard Standard 1500-320-100 + 0.005″ – 0.005″ 1500-320-110 + 0.005″ Standard 1500-320-114 Standard – 0.005″ 1500-320-117 + 0.010″ – 0.010″ 1500-320-120 + 0.010″ Standard 1500-320-124 Standard – 0.010″ 1500-320-127 + 0.005″ – 0.010″ 1500-320-130 Piston Rings CT20/26 Turbine Compressor OD Width Standard Standard 1500-320-160 + 0.010″ Standard 1500-320-180 Standard + 0.010″ 1500-320-181 + 0.010″ + 0.010″ 1500-320-182 Standard Standard

Related Content:

1998 chevy silverado manual, Replacing the reverse band Dodge 1500, 1998 chevy 1500 heater case, 90 ford aerostar repair manual, repair manual for 1998 chevrolet 1500, ax12-1500 nut torque, downloadable schematic for 99 Chevy suburban evap system, 2010 silverado 1500 4 3 liter canister vavle solenoid, how to replace actuator on 2005 chevy 1500, lifter repair on 02 avalanche

HIGH TECH DUAL QUAD THROTTLE LINKAGE KIT INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 24-02-2012

download
INSTALLATION 1. This kit contains all the necessary parts to operate Edelbrock carburetors in a progressive or 1: 1 type operation. Figure 1 illustrates typical progressive type installation in which the rear carburetor is the primary carb. This simplifies linkage attachment to the vehicle’s existing throttle linkage. 2. Before attaching anything to the carburetors, loosely assemble the major components of the linkage kit using Figure 1 as a guideline. Note that the longer rod will go to the rear carb with the flat facing down, and the short rod goes to the front carb with the flat facing up. The brass bearing blocks should be positioned so that the set screws will tighten against the flat of the short rod, i.e., both bearing block set screws will be up. Attach the aluminum collar to the long rod between the bearing blocks with the set screw against the flat. 3. Attach the linkage assembly to the carbs with the 10-24 allen head screws and locknuts. Attach to the rear carb using one of the brass 518″ O.D. x 3/16″ I.D. shoulder spacers and the tapered brass anti-rotation shoulder spacer in the top hole of the throttle arm (112″ diameter). Note that the shoulder spacer goes on the inside and the anti-rotation spacer goes on the outside of the throttle arm. Attach to the front carb using the 3/16″ hole just below the large hole in the throttle arm. ADJUSTMENT – NOTE: If carburetors are full of fuel, place rags in the carb throats to absorb the fuel discharged when working the throttle linkage. This will prevent flooding and possible damage to the piston rings upon start-up. Be sure to remove the rags before starting engine. 1. Tighten the set screw and locknut on the rear bearing block, making sure that the bearing block is close to the end of the shaft from the front carburetor. 2. Push the throttle arms of both carbs to WOT (Wide Open Throttle), then adjust the aluminum collar to touch the rear brass bearing block. Securely tighten the set screw and locknut on the aluminum collar. 3. Let both throttle arms return to idle position, then adjust the front brass bearing block to almost touch the aluminum collar. Leave about .020″-.030″ clearance to allow for independent idle speed adjustment of each carburetor. Tighten all set screws, locknuts, and bolts at this time. 4. Check for smooth operation of linkage from idle to WOT and note that the rear carb will open about 20″ before starting to open the front carb. Both carbs should reach WOT at the same time. 5. IMPORTANT: Attach a return spring to both carburetors as shown in Figure 1. Use the return spring brackets supplied, bending as necessary for attachment to your engine. Generally the brackets can be attached to the intake manifold using the existing bolts. Use the longer or shorter spring on either the front or rear carburetor as required for your particular application. Check for smooth operation and positive return to idle. 6. Attach existing throttle linkage to rear carburetor using the 3/16″ hole below the large hole in the throttle arm. It may be necessary to shorten your existing linkage rod or cable, or to use an aftermarket cable mounting plate. BEFORE STARTING ENGINE, DOUBLE-CHECK FOR SMOOTH OPERATION OF LINKAGE FROM IDLE TO WIDE OPEN THROTTLE AND FOR POSITIVE RETURN TO IDLE. OPTIONAL 1:l INSTALLATION If 1:l linkage is desired, assemble and attach linkage kit as above, except that the attachment point to the front carburetor’s throttle arm will be the large 112″ hole using the other two 518″ O.D. x 3/16″ I.D. shoulder spacers (similar to the rear carburetor). Adjust the bearing blocks to eliminate all freeplay, so that all motion to the rear carburetor’s throttle arm is transmitted directly to the front carb’s throttle arm

Related Content:

vacuum connection for kancil, 4g13 engine ignition adjustments, specialist kancil carburetor, setting caburater kancil, schematic diagram of elect fuel system include locations for a 1989 toyota camry 2 0 engine passenger car, kancil overhaul module, kancil carburetor tuning, how to change kancil carburetor, Duromax 7 hp idle adjustment, carter duel quad carb adjustment

HIGH TECH DUAL QUAD THROTTLE LINKAGE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (More Manuals) by admin on 02-01-2012

download
INSTALLATION 1. This kit contains all the necessary parts to operate Edelbrock carburetors in a progressive or 1: 1 type operation. Figure 1 illustrates typical progressive type installation in which the rear carburetor is the primary carb. This simplifies linkage attachment to the vehicle’s existing throttle linkage. 2. Before attaching anything to the carburetors, loosely assemble the major components of the linkage kit using Figure 1 as a guideline. Note that the longer rod will go to the rear carb with the flat facing down, and the short rod goes to the front carb with the flat facing up. The brass bearing blocks should be positioned so that the set screws will tighten against the flat of the short rod, i.e., both bearing block set screws will be up. Attach the aluminum collar to the long rod between the bearing blocks with the set screw against the flat. 3. Attach the linkage assembly to the carbs with the 10-24 allen head screws and locknuts. Attach to the rear carb using one of the brass 518″ O.D. x 3/16″ I.D. shoulder spacers and the tapered brass anti-rotation shoulder spacer in the top hole of the throttle arm (112″ diameter). Note that the shoulder spacer goes on the inside and the anti-rotation spacer goes on the outside of the throttle arm. Attach to the front carb using the 3/16″ hole just below the large hole in the throttle arm. ADJUSTMENT – NOTE: If carburetors are full of fuel, place rags in the carb throats to absorb the fuel discharged when working the throttle linkage. This will prevent flooding and possible damage to the piston rings upon start-up. Be sure to remove the rags before starting engine. 1. Tighten the set screw and locknut on the rear bearing block, making sure that the bearing block is close to the end of the shaft from the front carburetor. 2. Push the throttle arms of both carbs to WOT (Wide Open Throttle), then adjust the aluminum collar to touch the rear brass bearing block. Securely tighten the set screw and locknut on the aluminum collar. 3. Let both throttle arms return to idle position, then adjust the front brass bearing block to almost touch the aluminum collar. Leave about .020″-.030″ clearance to allow for independent idle speed adjustment of each carburetor. Tighten all set screws, locknuts, and bolts at this time. 4. Check for smooth operation of linkage from idle to WOT and note that the rear carb will open about 20″ before starting to open the front carb. Both carbs should reach WOT at the same time. 5. IMPORTANT: Attach a return spring to both carburetors as shown in Figure 1. Use the return spring brackets supplied, bending as necessary for attachment to your engine. Generally the brackets can be attached to the intake manifold using the existing bolts. Use the longer or shorter spring on either the front or rear carburetor as required for your particular application. Check for smooth operation and positive return to idle. 6. Attach existing throttle linkage to rear carburetor using the 3/16″ hole below the large hole in the throttle arm. It may be necessary to shorten your existing linkage rod or cable, or to use an aftermarket cable mounting plate. BEFORE STARTING ENGINE, DOUBLE-CHECK FOR SMOOTH OPERATION OF LINKAGE FROM IDLE TO WIDE OPEN THROTTLE AND FOR POSITIVE RETURN TO IDLE. OPTIONAL 1:l INSTALLATION If 1:l linkage is desired, assemble and attach linkage kit as above, except that the attachment point to the front carburetor’s throttle arm will be the large 112″ hole using the other two 518″ O.D. x 3/16″ I.D. shoulder spacers (similar to the rear carburetor). Adjust the bearing blocks to eliminate all freeplay, so that all motion to the rear carburetor’s throttle arm is transmitted directly to the front carb’s throttle arm

Related Content:

iS THERE A SPRING CONNECTING THE LINKAGE TO THE TPS ON A97 LESABRE, edelbrock dubble carburetor adjustment linkage, relearn on throttle body trailblazer 2005, throttle body for a 2006 buick rendezvous, relearn procedure for throttle body 2004 chevy trailblazer, volvo penta throttle control diagram, p1512 chevy trailblazer, where is the fuel line to throttle body on a 2006 KIA RIO, lincoln ls throttle linkage, jaguar s type throttle body return spring

Honda Idle Fluctuation and/or the MIL Is On With DTC P1129 and/ or P0505 Repair Manual

0

Filed Under (Honda Manuals) by admin on 07-05-2012

download
DIAGNOSIS 1. Start the engine, and let it idle until it warms up. Does the idle fluctuate, or is there a customer complaint of an intermittent idle fluctuation? Yes – Odyssey : Go to REPAIR PROCEDURE A. Pilot : Go to REPAIR PROCEDURE B. No – Go to step 2. 2. Connect the HDS to the vehicle’s DLC, and check for DTCs. Is DTC P1129 or P0505 stored? Yes – Go to REPAIR PROCEDURE B. No – Continue with normal troubleshooting. REPAIR PROCEDURE A 1. Connect the HDS to the vehicle’s DLC. 2. Start the engine, and turn on the HDS. 3. When prompted, enter the VIN and the odometer reading 4. From the System Selection Menu screen, select PGM-FI . 5. From the Mode Menu, select DATA LIST . 6. Scroll down the list to PSP SWITCH . Watch the reading in the Value column. 7. Check for a broken power steering pressure switch wire by wiggling the P/S pressure switch wire harness at the switch while you check the Value column reading. •If the reading changes between on and off when you wiggle the harness, go to step 8. •If the reading does not change between on and off when you wiggle the harness, go to REPAIR PROCEDURE B. 8. Raise the vehicle on a lift, and remove the right front wheel to access the power steering pressure switch. 9. Disconnect the connector from the switch, and release the harness clip from the body. NOTE: You may need to disconnect the Secondary HO2S connector to free the end of the harness from the body. 10. Lower the vehicle, and pull the harness up for easier access to make the repair. 11. Remove the rubber seal from the connector, and remove the terminals from the connector noting the GRN wire and BLK wire locations. 12. Remove the tape from the corrugated tube and the wires up to the harness clip; mark the wires at the end of the corrugated tube

1999 GMC Truck Yukon PRNDL Display Inaccurate or Inoperative PRNDL Inaccurate Repair Manual

0

Filed Under (GMC Manuals) by admin on 15-02-2012

download
Did you perform the Instrument Cluster System Check? — Go to Step 2 Go to Instrument Cluster System Check 2 1. Disconnect the Transmission Range (TR) Switch connector C2. 2. Turn the ignition switch to the RUN position. 3. Conduct the PRNDL Logic Input Test by connecting fused jumper wires between ground and the appointed cavities of the TR Switch connector. Refer to PRNDL Logic Input Test PRNDL Logic Input Test . 4. Repeat for each transmission range. Do all ranges illuminate? — Go to Step 3 Go to Step 4 3 Adjust the transmission range switch. Refer to Park/Neutral Position Switch Adjustment (4L60E); Park/Neutral Position Switch Adjustment (4L80E) Automatic Transmissions. Replace the PNP Switch. Refer to Park/Neutral Position Switch Replacement (4L60E); Park/Neutral Position Switch Replacement (4L80E) in Automatic Transmissions. Is the repair complete? — Go to Instrument Cluster System Check — 4 1. Remove the I/P Cluster. 2. Connect a J 39200 DMM (continuity) between the I/P Cluster connector and connector C2 of the TR Switch to those circuit(s) that connected to the faulty PRNDL indicators. Is continuity present in the circuit(s) tested? — Go to Step 6 Go to Step 5 5 Locate and repair the open in the circuit(s) that are faulty between the TR Switch and the I/P Cluster. Refer to Wiring Repairs in Wiring Systems. Is the repair complete? — Go to Instrument Cluster System Check — 6 Connect a J 39200 DMM (continuity) between the I/P Cluster connector and ground to those circuit(s) that connected to the faulty PRNDL indicators. Is continuity present in the circuit(s) tested? — Go to Step 7 Go to Step 8 Locate and repair the short to ground in the circuit(s) that are faulty between the TR Switch and the I/P Cluster. Refer to Wiring 7 Repairs in Wiring Systems. Is the repair complete? — Go to Instrument Cluster System Check — 8 Replace the I/P Cluster. Refer to Instrument Panel Cluster (IPC) Replacement . Is the repair complete?

Related Content:

07tahoe dashboard repair kit, 1996 buick instrument cluster problems, 1999 yukon radiator removal instructions, 2006 buick torrent PRNDIL?, GM IPC CIRCUIT BOARDS

1989 Toyota 4Runner ENGINE PERFORMANCE Removal Overhaul And Installation

0

Filed Under (Toyota Manuals) by admin on 26-10-2011

download
CARBURETOR (COROLLA) REMOVAL 1) Drain cooling system. Disconnect air intake hose. Disconnect emission control hoses from air cleaner. Remove air cleaner mounting bolt and wing nut. Remove air cleaner. 2) Disconnect accelerator cable. Disconnect throttle cable (A/T). Disconnect carburetor wiring connector. Disconnect emission control hoses and tag for installation. Disconnect fuel inlet hose. Remove 4 carburetor mounting nuts and No. 1 vacuum pipe. Remove carburetor. DISASSEMBLY Air Horn 1) Remove air cleaner setting bolt. Remove fuel pipe clamp, union, fuel pipe and gaskets. Remove vacuum hoses. Remove pump and pivot screw and pump arm with connecting link. Disconnect choke link and choke opener link. 2 Remove 8 air horn screws and number plate, fuel pipe support and wire clamps. Remove air horn from carburetor body. Disconnect wiring from solenoid valves. 3) Remove float pivot pin, float and needle valve assembly. Remove air horn gasket, needle valve seat and gasket, power piston retainer, power piston and spring. Remove pump plunger and boot. See Fig. 2.
Fig. 1: Exploded View of Aisan Carburetor Main Body (Corolla) Courtesy of Toyota Motor Sales, U.S.A., Inc. Fig. 2: Exploded View of Air Horn Assembly (Corolla) Courtesy of Toyota Motor Sales, U.S.A., Inc. Main Body 1) Remove solenoid valves from carburetor body. Remove stopper gasket. Disconnect throttle positioner links and remove bracket attaching bolts. Remove accelerator pump retainer gasket and remove pump discharge weight, long spring and discharge large ball. See Fig. 1. 2) Remove pump dampening spring. Using tweezers, remove plunger retainer and check ball. Disconnect throttle positioner link and throttle position levers, washer and spring. Remove primary and secondary main passage plugs and gaskets. Remove primary and secondary main jets and gaskets. 3) Remove auxiliary acceleration pump (AAP) housing, spring and diaphragm. Remove AAP inlet plug and check ball. Remove outlet plug, short spring and small ball. Remove primary and secondary small venturies. 4) Remove sight glass retainer, sight glass and “O” ring. Remove throttle lever return spring and back spring. Remove throttle lever and fast idle cam. 5) Disconnect link and remove secondary throttle valve diaphragm assembly and gasket. Remove throttle position switch and bracket. Remove 3 body-to-flange screws and vacuum passage screw. Separate body from flange. See Fig. 3. Remove washer from throttle valve shaft. Remove idle mixture adjusting screw and idle speed adjusting screw.

Related Content:

yhs-mystartdefault, toyota 4k carburetor manual download, remove center peice from 2011 toyota camry, 2005 tundra grill removal, toyota sienna grill removal, mercedes 1997 cell phone manual for sl500, how to remove center console 2013 camry, jaguar fuel hose removal, how remove intake plenum on 1998 Toyota sienna, how replace alternator in 2006 honda odessey

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, gm 4l60e band adjustment screws, 2003 trailblazer torque converter removal, how to check tranmission fluid on 2012 kia sedona, 2011 crv engine whine, 2005 explorer transmission exploded view, automatic transmission adjustments for 1997 yuko, 1997 e450 power stroke trans mount parking brake, e4od repair manual download, manual pdf transmicion automatica ram 2001

INFINITI BRAKE NOISE/ JUDDER/ PEDAL FEEL DIAGNOSIS AND REPAIR MANUAL

0

Filed Under (Infiniti Manuals) by admin on 06-02-2012

download
APPLIED VEHICLES: All Infiniti SERVICE INFORMATION • This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. • Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. BRAKE NOISE • Brakes can make a range of noises when applied or released. Some noises are normal and no repair action should be taken. • Use the following descriptions to identify the specific type of brake noise and the appropriate repair: Squeak noise when the brakes are cold: • Usually occurs during the first few stops in the morning. • This is a normal condition. No service action is necessary Squeak noise with the brakes at normal operating temperatures: • listed under Brake Service on page 5 of this bulletin and the appropriate Service Manual procedures. • Refer to technical bulletins specific to the model of vehicle regarding this issue. If there are no bulletins for the car you are working on, install OE type pads using the information Notes about brake pads and brake noise: Original Equipment (OE) brake pads are installed on all current Infiniti vehicles at the factory. The OE pads use a Non-asbesto • s Organic (NAO) compound. The NAO material provides state of the art resistance to squeal noise. • ervice parts and must be used if replacing brake pads under the terms of • ted under Brake Service on page 5 of this bulletin and the appropriate Service Manual Gro n s after coming to a stop: • It is a normal condition. No repair or service is necessary. These pads are available as s the Infiniti new car warranty. Loud continuous squeak/squeal noise: • Occurs with or without braking. • This is a normal brake function. It occurs when the brake pad wear indicators contact the rotor. It indicates the brake pads are worn out and need to be replaced. Install new brake pads using the information lis procedures. anoise when slightly releasing the brake • This is sometimes called “creep groan

Related Content:

4t65e documentation pdf, 4t65e pdf

1999 Audi A6 Sedan Timing Belt Service and Repair

0

Filed Under (Audi Manuals) by admin on 04-06-2011

download
Toothed belt, removing and installing Removing – Remove engine cover (arrows). – Remove noise insulation panel (arrows). – Remove front bumper. Refer to Body and Frame/Bumper/Service and Repair – Move lock carrier to service position. Refer to Body and Frame/Radiator Support/Service and Repair – Remove ribbed belt. Refer to Engine/Drive Belts, Mounts, Brackets and Accessories/Drive Belt/Serpentine Belt/Service and Repair See: Drive Belt/Service and Repair CAUTION: Mark the running direction of the belt with a crayon or marker before removing. Reinstalling a used belt in reversed running direction could damage the belt. – Unclip toothed belt guard on both sides and remove. – Turn crankshaft by hand to TDC. Marks -A- and -B- must align – Check position of camshafts. Larger holes (arrow) of securing plates on camshaft sprockets must be on inside and must align If they are not in this position: Turn crankshaft one revolution further. – Remove sealing plug from left-side of cylinder block. Top Dead Center (TDC) mark on crankshaft must be visible or can be felt Crankshaft Holder 3242 Shown In Installed Position – Install 3242 crankshaft holder into opening. – Remove tensioner for ribbed belt. – Remove center and left belt guards. Notes: The toothed belt tensioner is oil-dampened. Compress it by slowly applying constant pressure. Use spring clamp from 2024A. – Using 8 mm hex wrench, turn toothed belt tensioning roller -1- counter-clockwise, opposite direction shown (arrow), until tensioning lever -2- compresses tensioner -3- so that spring clamp (2 mm dia.) can be inserted into bore and lifter. – Insert pin and release tension. – Remove vibration dampener. Refer to Engine/Cylinder Block Assembly/Harmonic Balancer/Service and Repair – Remove idler for ribbed belt and guard under vibration dampener (arrows). – Remove toothed belt.

Related Content:

Repair roller lifter

Related Content:

manual book kancil 850 pdf, FORD 555D VALVE SETTINGS, 1971 c10 service manual pdf, 1999 chevy S10 - manual, 2006 ford focus ses repair manual, Pontiac Grand-Am 1994-1998 workshop Service Repair Manual download, cft30 scan codes, 95 ford Windstar 3 8 change transmission shifter cable, 5 9 Cummins Service Manual, 5 9 cummins dodge engine service manual for 2006