how to repair shifter cable for 1999 taurus

You search PDF repair manual about how to repair shifter cable for 1999 taurus, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to repair shifter cable for 1999 taurus Direct Download speed 5432 Kb/s

  how to repair shifter cable for 1999 taurus Full Version speed 8172 Kb/s



2002 Chrysler 300M Special Floor Shift Service and Repair Manual

0

Filed Under (Chrysler Manuals) by admin on 14-02-2012

download
Vehicle Level Transmission and Drivetrain Automatic Transmission/Transaxle Shift Linkage Shift Cable Service and Repair Floor Shift Automatic Transmission GEAR SHIFT CABLE – FLOOR / REMOVAL 1. Using suitable size allen wrench, remove the shift handle retaining screw (Fig. 251). 2. Remove shift handle from shifter assy. 3. Remove console bezel from vehicle 5. Remove retaining clip from shift cable conduit bracket (Fig. 253). 6. Disconnect shifter cable from cable attach stud (pin) (Fig. 253). 7. Remove cable from center console routing. Leave flat on floor for ease of removal. 8. Raise hood. Remove gearshift cable from throttle/gearshift cable bracket (Fig. 254) 9. Unseat cable grommet at firewall and remove cable from interior of vehicle (Fig. 255). 10. Raise vehicle on hoist and disconnect fill tube bracket from transaxle. Rotate fill tube to gain access to shift cable clamp. 11. Remove cable from routing bracket (Fig. 256) 12. Remove cable-to-transaxle nut and slide cable off of stud (Fig. 255). 13. Disconnect shifter cable from shift lever assembly at transaxle (Fig. 255). 14. Remove cable from underneath vehicle. INSTALLATION 1. Make sure transaxle shift lever is in “Park.” This is the most rearward position. Verify park sprag is fully engaged by rotating either a tire or an axle shaft . 2. Position cable in vehicle and connect cable end to the transaxle shift lever (Fig. 255). 3. Verify that the washer (Fig. 255) is still in place on the cable mounting stud. Install cable to transaxle and tighten nut to 28 Nm (250 inch lbs.). 4. Rotate fill tube to original location. Install and tighten fill tube bracket bolt. 5. Install cable “push pin” into bracket as shown in (Fig. 254)

Related Content:

how install console shift handle 1999 taurus, 2002 expedition shifter cable disconnect, ford escape shift cable repair, 2006 gmc envoy rear hatch rubber boot wire harness, Dodge 3500 Brown how to install shifting cable, 2004 ford f150 transmission shift cable ends, saturn 2008 How to install bcm, shifter cable came off 2006 Buick Terraza, need diagram of shifter cable for 2008 chevy malibu lt, on a 2006 pt cruiser when takeing off the battery cable do you need to reset it

Various Concerns With Shifter and/or Ignition Key (Replace Shifter Assembly/Shifter Components or Ignition Lock Cylinder )

0

Filed Under (More Manuals) by admin on 05-05-2012

download
2005-2007 Chevrolet Cobalt 2005-2006 Pontiac Pursuit (Canada Only) 2007 Pontiac G5 with Automatic Transmission 4T45-E (RPO MN5) The illustration above shows the switch in a correct position. Cause 3 Metal flashing left in the cylinder may cause a high effort to rotate the key. Cause 4 The slider may be binding in the guides. This may cause the shifter to become difficult to operate. Correction 1 Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter assembly moves when activating the button. If the parking pawl does not move when the button is activated, the shifter handle will have to be replaced. Refer to Floor Shifter Control Knob Replacement in SI. Correction 2 Important: A change has been made to the shifter assembly for service. The replacement shifter assembly will read PRNDIL (Park, Reverse, Neutral, Drive, Intermediate and Low). Verify that the micro switch is out of position. Replace the shifter assembly. Refer to Transmission Control Replacement in SI. Correction 3 Important: Refer to instruction sheet that is supplied with the lock cylinder kit. BO 47869 is an essential staking tool and must be used for the repair. Replace the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement in SI. Correction 4 Replace the slide indicator and guides in the shifter following the procedure below: 1. Apply the parking brake. 2. Remove the upper console trim. Refer to Trim Plate Replacement-Console Front in SI. 3. Remove shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 4. Remove the indicator plate. Use a flat-bladed screwdriver to release the locking tabs. 5. Remove the shifter indicator lens. 6. Pull up on the indicator and remove it from the assembly. 7. Remove the two front rails by unsnapping the front and lifting up, and then back, to remove the rails from the shifter assembly. 8. Install the new guides. Place the hook end into the assembly and push down. It will snap into place. 9. Install the new slide indicator. With the transmission in neutral, place the slide over the shifter and into the guides. Move the slide indicator down the guides in the front and rear. Important: Replace the shifter indicator lens if damage is present due to the slider binding or if it becomes damaged during disassembly. 10. Install the shift indicator lens. 11. Install the shift indicator plate. 12. Install the shifter knob. Refer to Floor Shifter Control Knob Replacement in SI. 13. Install the upper console trim. Refer to Trim Plate Replacement-Console Front in SI

Related Content:

2006 impala shifter converison instructions, Removing a concole from 2006 monte carlo, How to replace shift indicator on 99 f150, replace shifting cable for 2003 GMC Envoy how do you remove the console, replace shifter handle on 2000 malibu, replace shifter cable 2003 rendezvous, cover push button on shifter for chevey 2007 cobalt automatic, buick rendezvous detached shifter, buick rendezvous gear shift cable repair, chevy cobalt shift lock

2003 Honda ODYSSEY Intake Manifold Removal and Installation Manual

0

Filed Under (Honda Manuals) by admin on 27-06-2012

download
Removal 1. Remove the intake manifold cover (A) and ignition coil cover(s) (B). 1999-2001 models: 2002-2004 models: 2. Remove the evaporative emission (EVAP) canister hose (A) (1999-2001 models) or vacuum hose (A) (2002-2004 models). 3. Remove the vacuum hose(s) (B) and breather pipe (C), then remove the intake air duct (D). 1999-2001 models: 2002-2004 models: 4. Remove the throttle cable (A) and cruise control cable (B) by loosening the locknuts (C), then slip the cable ends out of the accelerator linkage. Take care not to bend the cables when removing them. Always replace any kinked cable with a new one. 5. Remove the engine wire harness connectors and wire harness clamps from the intake manifold. *Intake air temperature (IAT) sensor connector *Idle air control (IAC) valve connector *Throttle position (TP) sensor connector *Manifold absolute pressure (MAP) sensor connector *Evaporative emission (EVAP) canister purge valve connector (2002-2004 models) 6. Remove the brake booster vacuum hose (A) and positive crankcase ventilation (PCV) hose (B). 7. Remove the vacuum hoses (C) (1999-2001 models). 1999-2001 models: 2002-2004 models: 8. Remove the breather hose (A) and water bypass hoses (B), then plug the water bypass hoses. 9. Remove the EVAP canister hose (C) (2002-2004 models). 1999-2001 models:

Related Content:

1999 honda civic ex manual, ashley recliner model 7528 parts, Savage Model 99 Manual, lazy boy model 7528, honda odyssey canister purge valve location, honda odyssey 2002 repair manual pdf, Honda Odyssey 2001 Parts Diagram, ashley recliner model 7528 replacement parts, 2001 civic fuel canister pdf, viper 4115v1remote start

2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration Repair Manual

0

Filed Under (Toyota Manuals) by admin on 30-05-2012

download
Harsh 5-4 Downshift on Deceleration Repair Procedure 1. Test drive and verify that the 5-4 harsh downshift condition occurs as described in the Introduction section in this TSB. 2. Replace the SLT solenoid assembly. Refer to the Technical Information System (TIS): •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” •2007 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2008 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2009 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” NOTE For SLTsolenoid identification, refer to TSB No. TC 007-05, “U250E Transmission Solenoid Identification”. 3. Reinstall the automatic transaxle oil pan. Refer to TIS: •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” • 2007 / 2008 / 2009 model year Camry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Installation” 4. Test drive and verify that the A TM operates normally

Related Content:

manual book kancil 850 pdf, FORD 555D VALVE SETTINGS, 1971 c10 service manual pdf, 6m70 engine manual pdf, cft30 scan codes, 1999 chevy S10 - manual, Pontiac Grand-Am 1994-1998 workshop Service Repair Manual download, pdf kancil 850 manual tranission, 2006 ford focus ses repair manual, 1996 buick regal 3800 owners mAnuel

Toyota CT20 CT20 Type Dynamic and Carbon Seal Repair Parts & Service Kits

0

Filed Under (Toyota Manuals) by admin on 23-06-2011

download
All parts are available for purchase as individual components or in the following popular Repair Kits Key Part number Description Q ty in Turbo 1500 – 320 – 750 1500 – 320 – 751 1500 – 320 – 752 1500 – 320 – 753 1500 – 320 – 754 1500 – 320 – 760 8 1500-320-100 Journal Bearing 2 2 2 2 2 2 2 9 1500-320-290 Bearing Spacer 1 11 1500-320-320 Thrust Bearing 1 1 1 1 1 1 14 1500-320-160 Piston Ring Turbine 1 1 1 1 1 1 1 15 1500-320-170 Piston Ring Compressor 1 1 1 19 1500-320-200 Thrust Collar 1 1 1 1 1 21 1500-320-220 Thrust Spacer Carbon 1 1 1 1 22 1500-320-221 Thrust Flinger Dynamic 1 1 24 1500-326-145 Seal Plate Retaining Ring 1 28 1500-320-310 Oil Deflector 1 29 1500-320-150 O Ring (Seal Plate) 1 1 1 1 1 1 1 30 1500-320-155 O Ring (CT20 C/Cover) 1 1 1 1 1 1 1 30 1500-320-156 O Ring (CT20 C/Cover) 1 1 1 33 1500-320-300 Seal Plate Assy Carbon 6.1mm Depth 1 1 1 1 34 1500-320-301 Seal Plate Assy Dynamic 1 1 34 1500-320-302 Seal Plate Assy Carbon 7.57mm Depth (for turbo 54030) 1 1 43 1500-320-351 Shaft Nut LHT 1 1 1 1 1 1 1 – 1500-320-790 Gasket CT20 Oil Inlet / outlet 1 1 1 1 1 1 1 – 1500-320-791 Gasket CT20 Water Inlet / Outlet 2 2 2 2 2 2 2 Description of Repair Kits available 1500-320-750 Repair Kit (Minor) CT20 Dynamic 1500-320-751 Repair Kit (Minor) CT20 Carbon Seal 1500-320-752 Repair Kit (Major) CT20 Carbon Seal 1500-320-753 Repair Kit (Major) CT20 Dynamic 1500-320-754 Repair Kit (Major) CT20 Carbon Seal (54030 Only) 1500-320-760 Repair Kit CT20 (Carbon Seal – No thrust bearing Notes: 1) CT20 and CT26 repair kits are identical except for the Comp Cover O-ring – USE 1500-326-754 kit to repair both CT20/CT26 dynamic models from one kit. 2) For Pre 1990 CT20 Landcruiser 2.4L (17201-54030), the seal plate flange is deeper ( Part No. 1500-320- 302 ) and the O-ring groove is Ø114mm in the comp cover rather than Bearing housing. Use kit 1500-320- 754. Version 7.0 CT20 Type Oversize Repair Parts Available Journal Bearings CT20/26 Standard Standard 1500-320-100 + 0.005″ – 0.005″ 1500-320-110 + 0.005″ Standard 1500-320-114 Standard – 0.005″ 1500-320-117 + 0.010″ – 0.010″ 1500-320-120 + 0.010″ Standard 1500-320-124 Standard – 0.010″ 1500-320-127 + 0.005″ – 0.010″ 1500-320-130 Piston Rings CT20/26 Turbine Compressor OD Width Standard Standard 1500-320-160 + 0.010″ Standard 1500-320-180 Standard + 0.010″ 1500-320-181 + 0.010″ + 0.010″ 1500-320-182 Standard Standard

Related Content:

1998 chevy silverado manual, 1998 chevy 1500 heater case, 90 ford aerostar repair manual, Replacing the reverse band Dodge 1500, 2010 silverado 1500 4 3 liter canister vavle solenoid, repair manual for 1998 chevrolet 1500, ax12-1500 nut torque, downloadable schematic for 99 Chevy suburban evap system, parts manual for lazy boy reclin, Pcv valve 2005 gmc 1500

1999 GMC Truck Yukon PRNDL Display Inaccurate or Inoperative PRNDL Inaccurate Repair Manual

0

Filed Under (GMC Manuals) by admin on 15-02-2012

download
Did you perform the Instrument Cluster System Check? — Go to Step 2 Go to Instrument Cluster System Check 2 1. Disconnect the Transmission Range (TR) Switch connector C2. 2. Turn the ignition switch to the RUN position. 3. Conduct the PRNDL Logic Input Test by connecting fused jumper wires between ground and the appointed cavities of the TR Switch connector. Refer to PRNDL Logic Input Test PRNDL Logic Input Test . 4. Repeat for each transmission range. Do all ranges illuminate? — Go to Step 3 Go to Step 4 3 Adjust the transmission range switch. Refer to Park/Neutral Position Switch Adjustment (4L60E); Park/Neutral Position Switch Adjustment (4L80E) Automatic Transmissions. Replace the PNP Switch. Refer to Park/Neutral Position Switch Replacement (4L60E); Park/Neutral Position Switch Replacement (4L80E) in Automatic Transmissions. Is the repair complete? — Go to Instrument Cluster System Check — 4 1. Remove the I/P Cluster. 2. Connect a J 39200 DMM (continuity) between the I/P Cluster connector and connector C2 of the TR Switch to those circuit(s) that connected to the faulty PRNDL indicators. Is continuity present in the circuit(s) tested? — Go to Step 6 Go to Step 5 5 Locate and repair the open in the circuit(s) that are faulty between the TR Switch and the I/P Cluster. Refer to Wiring Repairs in Wiring Systems. Is the repair complete? — Go to Instrument Cluster System Check — 6 Connect a J 39200 DMM (continuity) between the I/P Cluster connector and ground to those circuit(s) that connected to the faulty PRNDL indicators. Is continuity present in the circuit(s) tested? — Go to Step 7 Go to Step 8 Locate and repair the short to ground in the circuit(s) that are faulty between the TR Switch and the I/P Cluster. Refer to Wiring 7 Repairs in Wiring Systems. Is the repair complete? — Go to Instrument Cluster System Check — 8 Replace the I/P Cluster. Refer to Instrument Panel Cluster (IPC) Replacement . Is the repair complete?

Related Content:

07tahoe dashboard repair kit, 1996 buick instrument cluster problems, 1999 yukon radiator removal instructions, 2006 buick torrent PRNDIL?, 2006 nissan quest odometer repair sacramerto area, GM IPC CIRCUIT BOARDS

2006 Lexus GS300 Toyota i- -R DICE iPod Integration Kit for Radio Interface Kit Toyota

0

Filed Under (Toyota Manuals) by admin on 22-09-2011

download
1. Pull vehicle into service bay and access radio/center console. 2. Disconnect both battery terminals. These cables must be disconnected during installation to insure proper initialization of the DICE module when the DICE when it is connected. 4. The Shift knob needs to be removed by rotating it counter-clockwise. The trim plate around the shifter also needs to be removed. Clips on the side of the plate hold it in place and easily unsnap by lifting up the back of the plate. 5. The plate can be lifted up but will still be hinged in the front, underneath the radio. Move the shifter through the gears to allow the plate to be lifted up. Once the plate can be lifted remove the screw holding the side panels in place. The panel will now be held by clips only and can be unsnapped by pulling it way from the center console. 2 1 2 3 4 5a Make sure the key is removed from the ignition. If vehicle is equipped with keyless ignition, make sure vehicle is OFF. 5b 3 6. Remove any screws holding the radio in place, so the radio may be fully removed. The arrows indicate the location of the 4 screws (2 on each side of the console). After the screws are removed only clips will be holding the radio in place. The entire radio with navigation (if applicable) can be pulled out. 7. Connect the vehicle specific cable’s 8-pin molex and iPod Docking Cable to the DICE module. The correct plugs on the DICE module can be identified by matching it up with the connector or by looking for the label on the bottom of the module. connector 1/8″ AUX Dock Cable Vehicle Specific Cable 6 7 5. Shown is the CD Changer harness from the back of the radio. The vehicle specific cable will be interfacing from this point. Some radios may have the connectors in a different order than shown. Match up the DICE vehicle specific cable to the connector on the back of the radio. 6 b. If the vehicle is equipped with Sirius/XM satellite radio, then this connector will already be occupied. Disconnect and reconnect it to the optionalToyota Cable. a. For late modelToyotas using the optional Toyota Cable, the extra plug on theToyota interface cable wil

1999 Audi A6 Sedan Timing Belt Service and Repair

0

Filed Under (Audi Manuals) by admin on 04-06-2011

download
Toothed belt, removing and installing Removing – Remove engine cover (arrows). – Remove noise insulation panel (arrows). – Remove front bumper. Refer to Body and Frame/Bumper/Service and Repair – Move lock carrier to service position. Refer to Body and Frame/Radiator Support/Service and Repair – Remove ribbed belt. Refer to Engine/Drive Belts, Mounts, Brackets and Accessories/Drive Belt/Serpentine Belt/Service and Repair See: Drive Belt/Service and Repair CAUTION: Mark the running direction of the belt with a crayon or marker before removing. Reinstalling a used belt in reversed running direction could damage the belt. – Unclip toothed belt guard on both sides and remove. – Turn crankshaft by hand to TDC. Marks -A- and -B- must align – Check position of camshafts. Larger holes (arrow) of securing plates on camshaft sprockets must be on inside and must align If they are not in this position: Turn crankshaft one revolution further. – Remove sealing plug from left-side of cylinder block. Top Dead Center (TDC) mark on crankshaft must be visible or can be felt Crankshaft Holder 3242 Shown In Installed Position – Install 3242 crankshaft holder into opening. – Remove tensioner for ribbed belt. – Remove center and left belt guards. Notes: The toothed belt tensioner is oil-dampened. Compress it by slowly applying constant pressure. Use spring clamp from 2024A. – Using 8 mm hex wrench, turn toothed belt tensioning roller -1- counter-clockwise, opposite direction shown (arrow), until tensioning lever -2- compresses tensioner -3- so that spring clamp (2 mm dia.) can be inserted into bore and lifter. – Insert pin and release tension. – Remove vibration dampener. Refer to Engine/Cylinder Block Assembly/Harmonic Balancer/Service and Repair – Remove idler for ribbed belt and guard under vibration dampener (arrows). – Remove toothed belt.

Related Content:

Repair roller lifter

2002 NISSAN ALTIMA MANUAL A/C TEMPERATURE NOT ADJUSTABLE REPAIR MANUAL

0

Filed Under (Nissan Manuals) by admin on 11-05-2012

download
SERVICE PROCEDURE 1. Remove the following components; • cluster lid “C” (HVAC control surround trim) • fuse box cover • driver’s side instrument panel lower cover (attached with 2 screws). 2. Remove the screw from the center of the cable operated gear (see Figure 2). Figure 2 3. Locate the small (about 1″ dia.) white air mix door gear. Hopefully it is still on the floor. NOTE: If you cannot find the old air mix door gear, order a new gear. Refer to the Parts Information section of this bulletin. 4. To see how it is supposed to fit, temporarily install the gear into the air mix door shaft (see Figure 3). Figure 3 Air mix door drive gear (shown installed) Heater box Cable operated gear Retaining screw (remove) Front TP020106 Cable (do not detach) On the left side of the heater case, remove the screw from the center of the cable operated gear for the air mix door. Note: It is not necessary to detach the cable from the gear or the heater box. Proper pin location for air mix door/door gear with door/gear turned fully clock wise. Front TP010607a The gear can fit two different ways, only one of which is correct. Install the gear and rotate the gear/mix door shaft assembly fully clockwise so the gear’s index pin is at the 2 to 3 o’clock position. Cable (do not detach) Note: If the gear is in the correct spot, the alignment pin will be at the 2 to 3 o’clock position. POSITIONING THE GEAR CORRECTLY IS CRITICAL TO GETTING THE DOOR TIMING RIGHT. 3/5 5. Remove the gear, thoroughly clean the gear shaft of any grease, and apply the glue. See Figure 4. Figure 4 6. Re-install the gear into the mix door shaft (see Figure 5). Figure 5 TP010606a Air mix door gear (back side) Apply Glue to Shaded areas b. Apply plastic glue (3M dp-8005 or equivalent) to the shaft of the air mix door gear in the area where it inserts into the air mix door shaft. a. Thoroughly clean the air mix door gear shaft. Note: It is not necessary to clean the grease from the gear teeth. Front TP020100 Re-install the gear so the gear’s index pin is at the 2 to 3 o’clock position when the gear/mix door shaft assembly is turned fully clockwise. Proper pin location for air mix door/door gear with door/gear turned fully clock wise. 4/5 7. Set the HVAC control temperature dial as shown in Figure 6. Figure 6 8. Re-install the cable operated gear (see Figure 7). Figure 7 9. Operate the temperature control while watching the air mix door gear movement. They should operate freely with no binding. 10.Check the adjustment of the temperature cable as follows: A. Rotate the temperature control knob to the full COLD position (i.e., fully counterclockwise) and confirm the air mix door is fully seated (sealed) in the down position, then B. Rotate the temperature control knob to the full HOT position (i.e., fully clockwise) and confirm the air mix door is fully seated (sealed) in the up position. If the air mix door does not fully seat (seal) in either the full HOT or full COLD position: • Adjust the temperature control cable, with the temperature control knob in the full hot position, using the clip at the heater unit (see Figure 7) 11.Re-install the trim pieces removed in step 1.

Related Content:

how to check the backlash between the camshaft gear and the adjustable idler gear for 3406 e monel, used set of pistons for 2000 nissan altima with2 2, how to fix a shifter in a 2000 chevy malibu, VVTI GEAR POSITION DETERMINED BY CAM SENSOR WAVEFORM, how to change shift boot hummer h3, how to align cd4e mlp sensor, how do i replace the rear differential seal in my 2006 kia sorento ex 4wd, hino so5d gears, Gear shift nob broken on 2000 Chev Malibu, gear selector for 00 rodeo only goes in first and reverse

GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps)

0

Filed Under (More Manuals) by admin on 03-02-2012

download
GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps) Models: 2004-2007 Buick Rainier 2008 Buick Enclave 2003-2008 Cadillac Escalade Models 2005-2008 Cadillac CTS, SRX, STS 2006-2008 Cadillac DTS 2003-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer Models 2006-2008 Chevrolet Colorado 2007-2008 Chevrolet Equinox, HHR 2003-2008 GMC Envoy Models, Sierra, Yukon Models 2006-2008 GMC Canyon 2007-2008 GMC Acadia 2007-2008 Pontiac Torrent 2005-2008 HUMMER H2 2006-2008 HUMMER H3 2007-2008 Saturn OUTLOOK 2005-2008 Saab 9-7X This bulletin is being revised to update the models affected list. Please discard Corporate Bulletin Number 07-08-44-016 (Section 08 — Body & Accessories). Condition Some customers may comment on an inoperative display monitor or monitors in the GM Accessories Headrest DVD System. Cause This condition may be caused by a loose connection at the display monitor cable connectors. These connectors are located at the lower rear part of both front seats. Two cables are routed to the display monitor in each seat. Correction Do This Don’t Do This Install display monitor cable connector clamps. Do Not replace the DVD system display monitor. Important: A number of headrest monitors have been replaced under warranty and in many cases, no trouble was found by the supplier when these units were analyzed. Therefore, technicians should be checking for loose connections and installing cable connector clamps to ensure a positive and robust connection. Technicians are to install a video cable connector clamp on each cable connector located under each front seat. A total of four cable connector clamps, P/N 19159659, are required for each vehicle. The illustration above shows a pair of display monitor cable connectors without the cable clamps installed.

Related Content:

allinurl:Electronic Ignition Key , yhs-looksafe_ds_trans, 2008 checrolet colorodo emmisions purge valve, how to change the thermostat 2008 ford escape ehow, 2008 SCION XB BRAKE ROTOR RELEASE TOOL, 2008 pilot alternator replacement, Kia Spectra Repair Manual PDF, 2008 f250 haynes pdf, hummer h3 2008 p0741, 2008 toyota tundra tailgate latch assembly

Related Content:

how install console shift handle 1999 taurus, 2002 expedition shifter cable disconnect, ford escape shift cable repair, 2006 gmc envoy rear hatch rubber boot wire harness, Dodge 3500 Brown how to install shifting cable, 2004 ford f150 transmission shift cable ends, saturn 2008 How to install bcm, shifter cable came off 2006 Buick Terraza, need diagram of shifter cable for 2008 chevy malibu lt, on a 2006 pt cruiser when takeing off the battery cable do you need to reset it