Skip to content

how to replace 2004 kia amanti throttle position sensor

You search PDF repair manual about how to replace 2004 kia amanti throttle position sensor, if there are search results will appear below. If search results do not exist, please search by others keyword.

2004 Ford Truck Ranger 2WD Transmission Position Switch/ Sensor Service and Repair MANUAL

download
Special Tool(s) Removal 1. With the vehicle in NEUTRAL, position it on a hoist. 2. Disconnect the shift cable from the manual control lever. 3. Disconnect the digital transmission range (TR) sensor electrical connector. 4. Remove the manual control outer lever nut and manual control outer lever. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E 5. Remove the screws and the digital TR sensor. Installation 1. Install the digital TR sensor and loosely install the screws. 2. CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged. NOTE: The manual lever must be in the NEUTRAL position. Using the special tool, align the digital TR sensor and tighten screws in an alternating sequence. 3. Install the manual control outer lever and nut. 2004 Ford Truck Ranger 2WD V6-4.0L VIN E Copyright © 2007, ALLDATA 9.50 Page 3 4. Connect the digital transmission range (TR) sensor electrical connector. 5. Connect the shift cable to the manual control lever. 6. Verify that the shift cable is adjusted correctly.

Kia Sorento/ Sedona Throttle Position Sensor W/ 3.5L Engine (Fuel System) Service Procedure

download
Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly. Adjustment will be required. Re-install electrical connector to TP Sensor. 4. Install Global Diagnostic System. a. Select “System Option” b. Select “Idle RPM Adjust Mode” c. Apply Parking Brake 5. Select Neutral position and place engine in idle condition with A/C OFF. 6. Remove rubber plug and adjust using instructions provided on screen. Set Base idle between 800~900 rpm Adjust TPS: 7. Using the GDS scan tool, monitor current data using two (2) parameters: • Closed Throttle Position Switch • Throttle Position Voltage Value 8. Open throttle by hand very slowly until idle switch status switches to OFF. Note the TPS voltage value. Voltage:____________________________ 9. Close throttle and record the TPS voltage. oltage:____________________________ Closed throttle voltage should be 30~65mV less than the voltage noted in step eight (8). Adjust TP Sensor and repeat test as required. WARRANTY CLAIM INFORMATION: 10. Tighten TP Sensor screws as required. Torque is 12~18 inch lbs. Verify switching of throttle switch with throttle plate movement. 11. Install engine cover. 12. Clear any stored DTC which may have set during service procedure. Remove GDS tool from vehicle

2003 Honda ODYSSEY Intake Manifold Removal and Installation Manual

download
Removal 1. Remove the intake manifold cover (A) and ignition coil cover(s) (B). 1999-2001 models: 2002-2004 models: 2. Remove the evaporative emission (EVAP) canister hose (A) (1999-2001 models) or vacuum hose (A) (2002-2004 models). 3. Remove the vacuum hose(s) (B) and breather pipe (C), then remove the intake air duct (D). 1999-2001 models: 2002-2004 models: 4. Remove the throttle cable (A) and cruise control cable (B) by loosening the locknuts (C), then slip the cable ends out of the accelerator linkage. Take care not to bend the cables when removing them. Always replace any kinked cable with a new one. 5. Remove the engine wire harness connectors and wire harness clamps from the intake manifold. *Intake air temperature (IAT) sensor connector *Idle air control (IAC) valve connector *Throttle position (TP) sensor connector *Manifold absolute pressure (MAP) sensor connector *Evaporative emission (EVAP) canister purge valve connector (2002-2004 models) 6. Remove the brake booster vacuum hose (A) and positive crankcase ventilation (PCV) hose (B). 7. Remove the vacuum hoses (C) (1999-2001 models). 1999-2001 models: 2002-2004 models: 8. Remove the breather hose (A) and water bypass hoses (B), then plug the water bypass hoses. 9. Remove the EVAP canister hose (C) (2002-2004 models). 1999-2001 models:

2001 Chevrolet Chevy K Silverado Crankshaft Position Sensor Engine Stall Service Procedure

download
Why is your vehicle being recalled? Your vehicle may have a condition in which the crankshaft position sensor can fail intermittently or permanently. If the sensor fails intermittently, the Service Engine Soon (SES) light may illuminate and the vehicle may run rough. In addition, the engine may stall, and if so, may re-start immediately or after a cool down period. If the sensor fails permanently, the engine will quit running and will not re-start. If this happens while the vehicle is moving, a crash could result without prior warning. What will we do? Your GM dealer will replace the crankshaft position sensor. This service will be performed for you at no charge . Because of service scheduling requirements, it is likely that your dealer will need your vehicle longer than the actual service correction time of approximately one hour and twenty minutes. What should you do? You should contact your GM dealer to arrange a service appointment as soon as possible. Bring the enclosed customer reply form with you when you visit your dealer. The form identifies the repairs required. If you no longer own this vehicle, please let us know by completing the form and mailing it back to us. Did you already pay for this repair? The enclosed form explains what reimbursement is available and how to request reimbursement if you have paid for repairs for the recall condition.

2003-2004 Accord V6 MIL Comes On With DTC P2195 or P2197 REPAIR PROCEDURE

download
Before you update an ECM/PCM, make sure the battery in the vehicle is fully charged. •To prevent ECM/PCM damage, do not operate anything electrical (audio system, brakes, A/C, power windows, moonroof, etc.) during the update. 1. If not already done, load the May 2004 or later i N CD onto the i N master terminal. Loading instructions are included with the CD. 2. Update the ECM/PCM software with the HIM. For updating instructions, refer to Programming the HIM and Updating an ECM/PCM With a Programmed HIM in Service Bulletin 01-023, Updating Control Units/Modules . 3. Warm up the engine to operating temperature, then shut if off. 4. Do the ECM/PCM RESET and the CKP PATTERN CLEAR with the HDS. OP# Description FRTTemplate ID 123503Retrieve the DTC(s), and clear the codes with the HDS. 0.3 04-038A 125517Update the ECM/PCM software with the Honda Interface Module. 0.3 122505Do the CKP pattern learn. 0.32 of 2 04-038 5. Do the ECM/PCM idle learn procedure: •Make sure all electrical items (A/C, audio, rear window defogger, lights, etc.) are off. •Turn the ignition switch to the ON (II) position for 30 seconds. •Start the engine, and let it idle (throttle closed and all electrical items off) for 10 minutes. 6. Do the low-rpm CKP pattern learn: •Test-drive the vehicle on a level road: With the A/T in second gear, or the M/T in second or third gear, decelerate (with the throttle fully closed) from 2,500 rpm down to 1,000 rpm . •Stop the vehicle, and put the transmission into Park or Neutral. Set the parking brake. Do not turn off the ignition switch. 7. Connect the HDS to the DLC, and check the status of PULSER F/B LEARN: •On the Selection Menu , select PGM-FI . •On the Mode Menu , select Data List . •Check the value of PULSER F/B LEARN . •If the value is Completed , go to step 7. •If the value is Not Completed , be sure the engine is at normal operating temperature (the ECT SENSOR (1) value is 176 or higher), and return to step 5. 8. Do the high-rpm CKP pattern learn: NOTE: The low-rpm CKP pattern learn must be completed before you do the high-rpm CKP pattern learn. •Test-drive the vehicle on a level road: With the A/T in first gear, or the M/T in first gear, decelerate (with the throttle fully closed) from 5,000 rpm down to 3,000 rpm . •Stop the vehicle, and put the transmission into Park or Neutral. Set the parking brake. Do not turn off the ignition switch. 9. Connect the HDS to the DLC (if not already connected), and do this: •On the Selection Menu , select PGM-FI . •On the Mode Menu , select Data List . 10. Check the value of PULSER F/B LEARN (HIGH RPM) •If the value is Completed , you are finished. Disconnect the HDS. •If the value is Not Completed , be sure the engine is at normal operating temperature (the ECT SENSOR (1) value is 176 or higher), and repeat steps 5 thru 8