how to replace 2006 kia sedona front struts

You search PDF repair manual about how to replace 2006 kia sedona front struts, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to replace 2006 kia sedona front struts Direct Download speed 5432 Kb/s

  how to replace 2006 kia sedona front struts Full Version speed 8172 Kb/s



Toyota Front Coil Spring Spacer Lift Kit Installation Manual

0

Filed Under (Toyota Manuals) by admin on 22-12-2011

download
INSTALLATION INSTRUCTIONS FRONT 1. Read complete instructions before beginning installation, the following special tools are recommended: Coil spring compressor, floor jack, ball joint separator, jack stands, bench vise, and metric hand tools. 2. Jack the vehicle in the center of the front cross member. 3. Support the vehicle by placing jack stands on the frame cross member so that the front tire/wheels are off the ground. 4. Remove the front tires/wheels. 5. Disconnect the sway bar end links and remove the upper ball joint cotter pin and nut. 6. Separate the upper ball joint from the spindle. (Using ball joint separator or a suitable tool, be careful NOT to damage the ball joint boot) 7. Remove upper strut tower nuts holding strut assembly to strut tower (3) on each side of vehicle. 8. Remove the lower strut bolt from the lower control arm and remove the strut assembly from the vehicle. (Note the direction of the bolt for reinstallation) 9. Compress the coil spring on the strut assembly with a suitable coil spring compressor so that the coil spring has about 3/8″ play in the strut and remove the upper strut isolator mount nut. 10. Remove the coil spring isolator from the upper strut mounting plate. 11. Replace the upper strut mounting plate studs with the supplied studs with a bench vise and a deep well socket. (3 on each side) 12. Reinstall the factory coil spring isolator to the upper strut mounting plate. 13. Reinstall the compressed coil spring onto the strut assembly and reattach the upper strut mount plate using the stock hardware. See diagram. Torque upper strut mounting plate nut to 18 foot-pounds. 14. Decompress the coil spring in the strut assembly. Make sure that the spring is seated correctly into the strut assembly alignment indentation at the bottom of the strut and the top isolator. 15. Slide the coil spring spacer onto the top of the strut assembly over the 10mm studs. 16. Install the strut assembly into the strut tower and start the upper three 10mm lock nuts. (Make sure that the bottom of the strut is aligned as well) 17. Install the lower strut bolt in the original position and torque to 100 foot- pounds. (Step 8) 18. Using the floor jack, raise the lower control arm and connect the upper ball joint on the upper control arm to the spindle. Torque nut to 80 ft lbs. and make sure that you replace the cotter pin. (Not supplied) 19. Install the front tires/wheels. 20. Lower the vehicle onto the ground and tighten the upper strut tower 10mm nuts. Torque to 35 foot-pounds. (3 on each side) 21. RETORQUE ALL BOLTS AFTER 500 MILES.

Related Content:

what checks would you carry out before and after fitting a macpherson strut, sienna manual powered struts open manually, how man ft lbs for cadilla dts strut, how to replace upper strut mounts on a 2002 buick, how to replace front strut assembly 06 dakota, how to install lift support struts on 2006 Toyota Sienna, How to install lift gate struts, how to change out hatch struts on a toyota sienna, honda pilot strut replacement, Front strut replacement 1997 Ford Thunderbird

2006 Ford Explorer Scheduled Maintenance Guide

0

Filed Under (Ford Manuals) by admin on 12-02-2012

download
Scheduled Maintenance: 2006 Ford Explorer Driving Condition: Normal Condition Engine Displacement Transmission Fuel Cylinders Drivetrain 4.0 L Automatic Flexible 6 RWD ded Maintenance Mileage: Every 5,000 15 30 45 60 75 90 100 105 120 135 150 Value Package Price: See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer Change engine oil and replace oil filter (Up to 5 quarts of oil. Perform at specified mileage interval or every 6 months, whichever occurs first) – See dealer Perform multi-point inspection – See dealer Rotate and inspect tires; check wheel end play and turning noise – See dealer Inspect automatic transmission fluid level (if equipped with underhood dipstick) – See dealer Inspect brake pads/shoes/rotors/drums, brake lines and hoses, and parking brake system – See dealer Inspect engine cooling system and hoses – See dealer Inspect and lubricate all non-sealed steering linkage,ball joints,suspension joints,half and drive-shafts and u-joints – See dealer Inspect complete exhaust system and heat shields – See dealer Replace engine air filter – See dealer Replace fuel filter – See dealer Inspect 4×2 front wheel bearings; replace grease and grease seals, and adjust bearings – See dealer Change Premium Gold engine coolant – See dealer Inspect accessory drive belt(s) – See dealer Replace PCV valve – See dealer Replace spark plugs – See dealer Replace accessory drive belts (if not replaced within last 100,000 miles) – See dealer Replace rear axle lubricant – See dealer Change automatic transmission/transaxle fluid and filter – See dealer Notes: Prices are shown for illustrative purposes only and may vary based on required fluid quantities and other conditions. Information in this document is current as of January 07, 2010 and could change in the future.

Related Content:

replace radiator on hummer h3, 2006 nissan frontier cat replacement, hydraulic parking brakes on drive shaft, how to replace cat 05 frontier, how to replace an alternator on a 2006 honda pilot, how to replace a alternator on a 2006 honda pilot, how to change starter in 2006 chevy cobalt 2 2, ford explorer 2006 linkage repair, 2006 saturn ion maintenance recommendations, 2006 mercury 5 1 inboard starter smoking

2006 Saturn ION L4-2.2L VIN F Window Regulator Replacement – Front Door (Power Regulator) removal and installation procedure

0

Filed Under (Saturn Manuals) by admin on 05-01-2012

download
Removal Procedure 1. Lower the window to the full down position. 2. Remove the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door ) . 3. Remove the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 4. Remove the water deflector in order to access the window regulator. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 5. Disengage the door glass to the regulator sash channel clips (2). Separate the door glass from the sash channel (1). 6. Push the window to the up position and tape in place. 7. Loosen the power window regulator bolts. Remove the rear regulator bolt. 8. Lift the window regulator, disengaging the loosened bolts from the door. 9. Disconnect the regulator electrical connector. 10. Remove the power window regulator from the door. Installation Procedure 1. Loosely install the four forward fasteners into the window regulator. 2. Position the power window regulator in the door. 3. Connect the door window regulator electrical connector. Notice: Refer to Fastener Notice in Cautions and Notices. 4. Install the power window regulator bolts. Tighten the regulator bolts to 10 N.m (89 lb in). 5. Remove the tape from the window. Push the window down to the regulator sash channel. 6. Slide the glass sash clips (2) into the window regulator sash channel (1). 7. Install the water deflector. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 8. Install the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 9. Install the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door

Related Content:

what does a fuel pressure regulator do on a 2003 gmc yukon, 2009 focus exterior door hand replacing, 2005 yukon xl blend door problems, volvo penta impeller replacement instructions, how to remove a 2009 chev avalanche door panel, How to replace a window regulator on 2002 LIncoln ls, how to remove 2008 chevy silverado back passenger window replacement, replace temperature door actuator 2005 chevy 2500hd truck, replace lh front door regulator on 2002 explorer, remove alternator malibu 2010

1999-2006 TOYOTA TUNDRA FRONT LEVELING SYSTEM FOR THE 6-LUG SUSPENSION INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 04-12-2011

download
1. To begin installation, block the rear tires of the vehicle so that the vehicle is stable and can’t roll backwards. Safely lift the front of the vehicle and support the frame with jack stands. Place jack stands on both the driver and the passenger sides of the vehicle. Next remove the wheels from both sides. 2. Using a 17mm socket, remove the lower sway bar link bolt from both sides. HINT: If the stud turns together with the nut use a hex wrench or vice grips to hold the stud . 4. Next remove the strut’s lower mounting bolt with a 19 mm socket and wrench. NOTE: Once the nut is removed, it may be necessary to use a punch and hammer to free the bolt. 5. Remove the nuts from the three upper strut mounting bolts with a 14 mm ratchet. Be sure to support the strut assembly as the nuts are removed to prevent it from falling. 6. Remove the strut assembly from the vehicle and mount it in a bench vise. Install the steel strut extension on the top of the strut assembly. ** Caution: Use the factory nuts with the factory studs** 7. Run down nuts snug with end wrench. Torque to OEM specs. NOTE: Because of the shape of the steel spacer the strut will be rotated 180° when reinstalled. 8. Place strut back into upper strut mount. Tighten provided nuts snug with a 14mm wrench or ratchet (after install, you will torque to OEM specs). 9. Use a pry bar to position the lower control arm and the strut mount, and then reinstall the mounting bolt. Torque to OEM specs. 10. Place a jack under the lower control arm. Raise the lower control arm to reattach the lower ball joint bolts. Torque the ball joint nuts to OEM specs. 11. Repeat Steps 3 through 10 on the opposite side of the vehicle. 12. Reattach the sway bar link assembly on both sides of the vehicle. Torque to OEM specs. For 2wd trucks skip Step 13. 13. For 4×4 models only it is necessary to lower the differential using the provided spacers and bolts. Install the spacers following the instructions provided with the spacers. 14. Reattach the wheels. Torque to OEM specs. 15. Lower vehicle to the ground and torque strut mounts to OEM specs. 16. Align the vehicle. A certified alignment technician that is experienced with lifted vehicles is recommended to perform the alignment

Related Content:

2007 kia optima harmonic balancer bolt torque, volvo d13 flywheel torque spec, torque specs 04 gmc yukon, torque specs 4 8 chevrolet, torque specs for 5 7 volvo penta exhaust manifold, ax4n pan bolt torque spec, 2006 chrysler 300 rocker torque specs 2 7, lug nut torque on isuzi, 2001 buick lesabre strut torque, cummins n14 torque specs

2004 – 2006 Toyota Sienna Vehicles Equipped w/ Power Back Door (Power Rear Liftgate) Repair Manual

0

Filed Under (Toyota Manuals) by admin on 22-06-2012

download
Certain 2004 – 2006 Model Year Sienna vehicles equipped w/Power Back Door (Rear Liftgate) Q1: What is the condition? A1: Toyota has determined that the gas struts used to help lift and support the Power Rear Liftgate in certain 2004 through 2006 model year Sienna vehicles could be wearing out sooner than expected. As the gas struts deteriorate, the performance of the Power Rear Liftgate will begin to degrade, and the Power Rear Liftgate will operate more slowly than when the gas struts were new. Only Sienna vehicles equipped with the Power Rear Liftgate are involved. Q2: Are there any warnings that this condition exists? A2: Owners may notice that the Power Rear Liftgate will not remain in the open position. If not repaired, the gas struts may not be able to support the weight of the liftgate when it is open, and eventually, the gas struts could deteriorate to the point that the liftgate will fall about ten inches after it reaches the fully open position, at which point the power motor will engage and power the liftgate to the fully closed position. This condition may cause injury to a person who is struck by the liftgate when it falls or when it is closing. Q3: When were these vehicles produced, and how many vehicles are involved? A3: Only certain 2004 through 2006 model year Sienna vehicles equipped with the Power Rear Liftgate, produced between January 2003 and December, 2006 are involved. Approximately 196,000 vehicles are involved nationwide.

Related Content:

2006 pontiac torrent liftgate release switch, 2004 Toyota Sienna Manual PDF, 2004 sienna engine firing order, 2006 cadillac escalade liftgate problem blows fuses, free repair manual for a 2004 toyota sienna, owners manual for a 2006 scion xb, pt cruiser owners manual 2006, replace 2007 pacifica liftgate assists

2007-Up Toyota Tundra 2WD/4WD ADJUSTABLE UPPER STRUT FRONT LIFT/ LEVELING KIT INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 28-03-2012

download
Step 1: Measure current front ride height. Take a measurement from the bottom of the wheel/rim to the lip of the fender on each side of the vehicle. Write down measurements to help in determining ride height after new kit is installed. (Figure A) Step 2: Position vehicle on a flat surface or automotive lift. Suspend front wheels , lifting by the frame with a floor jack or lift jack. Secure using jack stands and wheel chocks. Be sure engine is turned OFF and vehicle is in PARK. Remove tire/wheel assembly on ONE side of vehicle . Step 3: Support Spindle to protect ABS system and brake lines! LOOSEN, but don’t completely remove upper ball joint nut, outer tie rod nut and sway bar link nut at the lower control arm. Step 4 : Break Outer tie rod and ball joint from their tapers using tools specific to this procedure. CAREFULLY, while supporting the spindle assembly, completely remove upper ball joint nut & tie rod nut, leaving the loosened sway bar link nut in place. ( Figure B) Step 5: Remove strut assembly from the vehicle. Remove LOWER strut bolt first, followed by the three (3) upper strut nuts. CAUTION! BE EXTREMELY CAREFULL TO SUPPORT STRUT ASSEMBLY WHEN REMOVING UPPER STRUT NUTS! The Strut/Spring assembly is heavy and can cause injury to technician or damage to other components if released too quickly! (Figure C) Step 6: Apply 50% of the INCLUDED Synthetic Grease to the TOP of the THREADED INNER ADJUSTMENT SCREW, as illustrated. (Figure D) Step 7: Using the original OEM stud nuts , secure new Adjustable Upper Strut Kit to OEM upper strut studs and torque to manufacturer’s specifications. (Figure E) IMPORTANT! Be sure the Threaded Adjustment Screw Rotates FREELY after securing kit to OEM top of strut! If not, slightly loosen the three upper stud nuts and reposition Threaded Adjuster Screw UPWARD slightly. Retorque upper stud nuts to manufacturer’s specifications and recheck that Inner Adjuster Screw rotates freely. Step 8: Install the Top Connection Plate ONLY, studs directed UPWARD, into position in the strut tower, and secure with the NEW Nylock stud nuts supplied with this kit. Torque stud nuts to OEM specifications. (Figure F) Step 9: Reinstall strut assembly . Be sure the new Adjustable Upper Strut Kit is THREADED DOWN in the MOST COMPACT POSITION for easiest reassembly, then pass exposed threaded area of the kit THROUGH the center of the Top Connection Plate already installed. HINT: The use of a pry bar or breaker bar may simplify reinstallation of the Strut Assembly. (Figure G) Step 10: Install Large 1-1/4-12 Adjustment Locking Jam Nut included with this kit and tighten until snug to Top Connection Plate. Install Snap Ring included with kit.

1995-2004 TOYOTA TACOMA 4 X 4 AND PRERUNNER 3″ SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 29-02-2012

download
Tacoma 4WD & PreRunner Installation Instructions Page 3 of 7 09/09/08 INST-425F.DOC FRONT OF VEHICLE 1. Park vehicle on level concrete surface. 2. Center and lock the steering wheel. 3. Block the rear wheels of the vehicle to prevent vehicle from moving in either direction. 4. Jack up the vehicle from the lift point in Figure “A.” 5. Support the vehicle with jack stands from the points in Figure “A.” 6. Remove the front wheels. 7. Remove the nut (14mm) and the hardware from the anti-sway bar. See Figure “B.” 8. Remove the nut (19mm) and bolt (14mm) from the bottom of the strut. See Figure “C.” 9. Remove the three nuts (14mm) from the top of the strut. See Figure “D.” 10. Remove the strut from the vehicle. NOTE: AT THIS TIME, IF YOU DO NOT HAVE A SUITABLE SPRING COMPRESSOR, IT IS HIGHLY ADVISED TO EITHER TAKE THE STRUT TO A QUALIFIED SERVICE CENTER OR PURCHASE THE REVTEK SC-1 SPRING COMPRESSOR. 11. Compress strut assembly and remove the nut (17mm) on the top of the strut shaft in Figure “E.” 12. Release the compressor. 13. Remove the spring top plate from the strut. 14. Remove and discard the rubber spacer. 15. Remove (hammer) the studs from the spring top plate. See Figure “F.” 16. Install (hammer) the LONGER STUDS (10MM) (provided) in the spring top plate. See Figure “G.” 17. Install the PRELOAD SPACER between the spring and the spring top plate with the small diameter facing toward the spring. See Figure “H.” 18. Compress the strut assembly, making sure you center the strut shaft through the spring top plate hole and that the STUDS line up with the PRELOAD SPACER reliefs. Replace nut on the top of the strut shaft and torque to spec. (Figure “E”). (Torque specs can be found on page 1.) 19. Install the TOP OUT EXTENDER over the STUDS (Figure “H”). 20. Reinstall the strut by reversing the removal procedure; torque to spec. (Torque specs on page 1.) 21. When properly installed, PRELOAD SPACER relief and Revtek Industries logo should face outward. (Figure R) 22. Reinstall hardware and nut on anti-sway bar; torque to spec. 23. Replace the wheels; torque to spec.

Related Content:

TORQUESPECLINCOLN2000

2001 – 2006 TOYOTA Sequoia BACK DOOR POWER WINDOW INOPERATIVE

0

Filed Under (Toyota Manuals) by admin on 11-01-2012

download
BACK DOOR POWER WINDOW INOPERATIVE – EL007-06 June 14, 2006 Page 2 of 6 ITEM NO. SPECIAL SERVICE TOOLS (SSTs) PART NUMBER QTYDRW** 1 Plastic Pry Tool Set* NOTE: All components from this kit/set are required 00002-06000-01 1 21 *Essential SSTs. **Refers to drawer number in SST Storage System. NOTE: Additional SSTs may be ordered by calling SPX/OTC at 1-800-933-8335. 1. Disconnect the negative (-) terminal of the vehicle battery. NOTE: Any time the negative (-) battery terminal has been disconnected, systems requiring initialization will need to be re-initialized after the negative (-) battery terminal has been reconnected. 2. Open the back door and leave open. 3. Using the plastic pry tool, remove the back door garnish center. 4. Using the plastic pry tool, remove the left and right back door side garnish panels. Required SSTs Repair Procedure : 5 Clips : 3 Clips BACK DOOR POWER WINDOW INOPERATIVE – EL007-06 June 14, 2006 Page 3 of 6 5. Remove the strap cover, bolt, and pull strap. NOTE: To remove the strap cover, push it toward the back door window as shown in the illustration. 6. Remove the back door trim board. A. Insert the plastic pry tool between the back door trim board to release the clips retaining the back door trim. NOTE: Be careful NOT to damage the back door and back door trim board. B. Release each clip as shown in the illustration. 7. Disconnect both connectors to the back door ECU and both clips holding the wire harness to the large service cover. 8. Remove both of the back door service hole covers. For 2001 – 2004 model year Sequoia vehicles, go to step 11. For 2005 – 2006 model year Sequoia vehicles, continue to step 9. 9. For 2005 – 2006 model year Sequoia vehicles ONLY: Remove the multiplex network door ECU. Using a drill of less than 3.2 mm (0.126 in.), drill out the two (2) rivet heads. HINT: Gently and vertically put the drill to the rivets and cut the rivet flanges. CAUTION: Take care as the cut rivets may be HOT. 10. For 2005 – 2006 model year Sequoia vehicles ONLY: Install the replacement multiplex network door ECU and rivets

Related Content:

2006 pt cruiser install guide, 2006 mercury eatc repairs, 2006 kia rio service manual free download, Back Door Power Window Inoperative - EL007-06 - June 14 2006, remove transmission control module G500, where to fine starter location in 2006 chevy calorando, 2006 npr freon capacity, 2006 chevy colorado service manual free, 2006 Chrysler 300c srt8 service and repair manual pdf download, enigine diagram for 2006 grand prix

2004-2006 Chevrolet Malibu, Malibu Maxx Loss of Power Steering Assist, Power Steering Warning Message Displayed in DIC, IPC/Radio Displays Erratic, DTC C0900, B1325 Set (Replace Ignition Coil/Module Assembly and Add Ground Strap)

0

Filed Under (Chevrolet Manuals) by admin on 10-01-2012

download
Correction Replace the ignition coil/module assembly and add ground strap following the procedure below. 1. Disconnect the ignition coil electrical connector. 2. Disconnect the left side spark plug wires from the ignition coil. 3. Disconnect the right side spark plug wires from the ignition coil. 4. Remove the four bolts attaching the ignition coil to its mounting bracket and remove the ignition coil. 5. Remove the ignition coil from the mounting bracket. 6. Loosen the two lower ignition coil mounting bracket nuts. 7. Remove the two upper ignition coil mounting bracket bolts and discard. Subject: Loss of Power Steering Assist, Power Steering Warning Message Displayed in DIC, IPC/Radio Displays Erratic, DTC C0900, B1325 Set (Replace Ignition Coil/Module Assembly and Add Ground Strap) Models: 2004-2006 Chevrolet Malibu, Malibu Maxx with 3.5L Engine (VINs 8, N — RPOs LX9, LZ4) 8. Install the ground strap (1), P/N 12581176, to the upper left side of the bracket as shown between the coil bracket and intake. Install the new bracket bolt, P/N 11570082, (do not tighten at this time). Prior to installing the ground strap, remove the captured nut and washers. They are not needed (simply pound them out with a hammer on a vise). 9. Install the washer (2), P/N 02436162, to the upper right side of the bracket between the coil bracket and intake. Install the new bracket bolt, P/N 11570082, (do not tighten at this time). Tighten Tighten all the ignition coil bracket bolts and nuts to 25 N·m (15 lb ft). 10. Install the new ignition coil to the mounting bracket. 11. Install the other end of the ground strap to the coil as shown and secure using a new bolt, P/N 11588715. 12. Install the other three ignition coil bolts. Tighten Tighten the bolts to 10 N·m (89 lb in). 13. Connect the right side spark plug wires to the ignition coil. 14. Connect the left side spark plug wires to the ignition coil. 15. Connect the ignition coil electrical connector

Related Content:

diagram for ignition wires on a 1998 sebring 2 5l, replac upper valve cover gasket 2005 chevy malibu maxx 3 5, Owners Manual 2004 Chevy Malibu Maxx, malibu ml60t manual, how to replace a ignition coil on 2004 toyota sienna, repair of saab ignition coil, mazda speed 6 ignition module, firing order for a 2006 chevy malibn maxx, 1999 saturn replacement ignition switch bolts, 2006 pontiac torrent replacement ignition

Remote Keyless Entry (RKE) Inoperative, Poor Range, Tire Pressure Monitor (TPM) Message Displayed, Remote Vehicle Start (RVS) (Replace/Reprogram RCDLR, Replace Antenna and Transmitters)

0

Filed Under (More Manuals) by admin on 28-01-2011

download
Models: 2006-2007 Buick Lucerne 2006-2007 Cadillac DTS 2006-2007 Chevrolet Impala, Monte Carlo 1. Replace the RCDLR module and the RCDLR antenna using the following procedure: Impala / Monte Carlo DTS • DTS / Lucerne: 5/1/07 • Impala / Monte Carle: 3/1/07 • The 2006 and 2007 Impala LS without AP8 does not have a coax antenna. • The 2006 and 2007 Lucerne without AP3 or AP8 does not have a coax antenna. 1.1. Remove the driver’s side “A” pillar molding and I/P closeout panel. 1.2. Unplug the speaker. 1.3. To expose the RCDLR antenna, partially remove the driver’s side upper I/P closeout panel (near windshield). 1.4. Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the “A” pillar. 1.5. Cut the old RCDLR antenna wire a minimum of 152 mm (6 in) from the button (connecting to the windshield), leaving that portion of the old RCDLR antenna connected to the windshield. 1.6. Remove the I/P carrier bolt and remove the old RCDLR antenna. 1.7. Remove the RCDLR module. 1.8. Install the new RCDLR module. 1.9. Lay in the new RCDLR antenna and reinstall the carrier bolt. 1.10. Connect the new antenna to the RCDLR antenna module. 1.11. Clip the new RCDLR antenna into place using the existing holes on the “A” pillar. 1.12. Reinstall the I/P close-out panel. 1.13. Reconnect the speaker wire. Important: Be sure that the end of the old RCDLR antenna is tucked behind the “A” pillar molding. The button on the windshield is no longer functional, however leaving the cover on the button will provide a cleaner look to the vehicle. 1.14. Reinstall the “A” pillar molding and I/P side closeout panel. 1.1. Remove the rear seat cushion. 1.2. Remove the rear seat back.

Related Content:

antenna repair torrent, 04 impaia p0455, 2006 chev impala remote lock location, how to remove back seat in 2007 Buick lucerne, how to remove the back seat on buick lucerne 2006 v6, how to repace autana on 2000 tacoma, is the keyless entry module wiring in all 02 monte carlos, location rcdlr hummer h2, partially blown channel plate gasket 2001 chevy malibu, remove back seat 2008 dts

Related Content:

what checks would you carry out before and after fitting a macpherson strut, sienna manual powered struts open manually, how man ft lbs for cadilla dts strut, how to replace upper strut mounts on a 2002 buick, how to replace front strut assembly 06 dakota, how to install lift support struts on 2006 Toyota Sienna, How to install lift gate struts, how to change out hatch struts on a toyota sienna, honda pilot strut replacement, Front strut replacement 1997 Ford Thunderbird