how to replace 2007 camry bumper cover

You search PDF repair manual about how to replace 2007 camry bumper cover, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to replace 2007 camry bumper cover Direct Download speed 5432 Kb/s

  how to replace 2007 camry bumper cover Full Version speed 8172 Kb/s



TOYOTA FJ CRUISER – FRONT BUMPER INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 05-02-2011

download
Front Bumper Installation – TOYOTA FJ CRUISER Step 1 Very Important Before beginning installation, assure that vehicle has been pulled forward into work-area with the wheels straight and that the ground is level. The clearances around the FJ bumper are critical to proper installation and fitment. Moving vehicle with wheels turned causes slight frame twist preventing ease of removal of OE bumper and installation of new bumper without issue. Make sure you have plenty of room to work around front of vehicle. Open the hood at this time, you will need to see down through the inner-body core-support while removing your OE bumper and installing your Body Armor FJ Bumper. Step 2 a. Unpack bumper using staple puller to remove staples. Save all packing materials and take care not to tear cartons. b. Remove hardware and misc.parts. Check parts/hardware list to confirm all parts and necessary hardware are included. c. It’s a good idea to spray all OE attaching hardware at this time with penetrating oil before beginning removal of OE bumper. This will ease removal as well as to help assure that none of the bolts’ / nuts’ threads are damaged during removal. Use extra caution when working with the bumper mounting studs & nuts. Step 3Prep bumper for install: You may install your auxilary lights in the light pockets. The light tab is slotted to allow for adjustment for adjustment for light grilles. You may also attach a second set of lights on the top deck . Also attach the grill guard at this time. Step 4 a. Begin removing OE bumper following instructions and photos on the following page for detailed descriptions and references. When done, proceed to Step 4 here. Step 5 a. If equipped, remove OE chassis skid plate and set aside for install after new bumper is installed. Save OE hardware to re-install the skid plate once new bumper is installed (3 upper bolts and 2 lower bolts, lowers have spacers between frame & skid plate). b. Remove the (3) outer hold-down hex nuts holding bumper to frame-caps on both passenger and driver sides. Un-clip the outer ends of the bumper from the outer bumper support clips (see Photo 5 on following page) by pulling bumper fascia down and out of clip on driver and passenger sides. Next, while a helper holds the bumper in place, loosen and remove the inner hold-down hex nuts on both passenger and driver sides. Reference Photo 1 on the last page for stud locations. The bumper should now slide off the front of the locating / mounting studs in the frame-caps. Remove slowly prevent paint damage. Save hold-down nuts. c. Remove the outer bumper support clips from both driver and passenger sides (see Photo 5 on following page) Step 6 a. If you bought a winch, skip to Step 6b. If you did not purchase a winch, you can mount the winch cover plate / lower bumper fascia, and fairlead slot cover plate to the bumper now, using (6) 3/8″ x 1″ bolts with (2) flat washers, (1) lock washer, and (1) hex nut on each bolt. See photos 4 & 5 on the last page for reference. b. If you purchased a winch for your FJ, now is the time to mount it in the bumper. The winch will bolt down using the fairlead mounting bracket and 10mm bolts to secure winch & fairlead bracket to bumper. The roller fairlead bolts to the fairlead bracket using the 1/2″ hex nuts supplied. See photo 3 on the last page for reference. Be sure to mount with the correct side of winch to passenger side for solenoid pack installation / clearance. Once the winch is bolted in, you can mount the winch cover plate / lower bumper fascia to the bottom of the bumper using (4) of the 3/8″ x 1″ bolts with (2) flat washers, (1) lock washer and (1) hex nut on each bolt. If you purchased lights, mount them to the light tabs. It the lights have a protective grille you should be able. to use the cover. Important: Follow winch mfr’s directions for cable to winch / solenoid / battery connections. Use caution to assure clearance of any and all bumper / winch / mounting surfaces at all cable end connections. Coil cables and lay in winch mount plate to protect against damage while installing bumper onto vehicle. Place coiled cables in winch mount plate to assure no interference with the radiator, a/c line and / or inner body core support during bumper installation. Cables to be run in Step 7. Step 7 Along with your helper, one person on each side, guide your Body Armor FJ Bumper onto the the frame-cap mounting studs. Use caution guiding the bumper on slowly and evenly to prevent paint damage. Locating / mounting studs and bumper mounting plates can be seen down through inner-body core support while guiding bumper into place. Make sure the bumper does not contact grill or fascia while installing bumper as this can cause paint damage. While you or your helper hold the bumper in place, thread the OE hold-down nuts onto mounting studs to hold the bumper in place, hand tighten at this time. Step 8 Confirm bumper is even side-to-side, torque hold-down nuts to 80 ft.lbs. Again confirm bumper is even and there are no clearance issues between the bumper and any part of the body and / or inner-body core-support. You can now run the winch cables through the inner-body core support to the battery. If you purchased a set of lights to be used with your bumper, you can now wire them up, please follow the detailed light manufacturer instructions. **Body Armor is not responsible for any issues with respect to the wiring, operation or warranties to the lights Step 9 a. Fit the wheel well inner-liner end-caps to the bottom of the bumper at each corner and bolt up with supplied 1/4″ x .75″ phillips- head machine screws, (2) each side, into drilled / threaded holes in bottom corners of bumper. See photos 6 & 7 on the last page. b. Next, using the OE hardware and spacers, re-install your chassis skidplate, making sure it’s straight before tightening. c. Using the (2) remaining 1/4″ x .75″ phillips-head machine screws, mount your license plate to threaded holes in the bumper face. d. Re-install the grill by snapping onto clips and using the OE push-pins and screws to hold down in OE locations. ** trimming off the front inner fender is a customer option, it is not required. We recommend you check the torque of all bolts after about two weeks, and after every off-road / trail run thereafter to assure tightness

Related Content:

how to remove chevy sonic front bumper, INSTALLING A FRONT BUMPER ON THE TOYOTA RAV 4, replacing front bumper end cap on 2012 Toyota FJ cruiser, 2004fordf150frontbumperdiagram, 2000 4runner step bumper rear chrome install instructions, remove back bumper on kia sedona cover, remove back bumper on kia sedona, remove 2006 toyota matrix rear bumper, rear fender for 2008 camry, you tube remove rear bumper camry 2000

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

0

Filed Under (More Manuals) by admin on 07-07-2012

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

Related Content:

2007 buick lacrosse window relay, chevy hhr evap, bypass anti-theft 2007 silverado, pontiac 2007 g6 remove radiator cover, how to change intake gasket 2007 grandprix, schematic for front brakes on 2005 Buick Rendezvous, 200lolds aleroraditor system, w584a lincoln, 2007 Chevy Colorado Gas Tank Seal replace, 4t65e service manual online

2007 TOYOTA FJ CRUISER HEAVY DUTY WINCH BUMPER INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 05-04-2012

download
INSTALLATION 1. Remove the screws from the rear corners of the bumper, two in each side. Figure 2 Figure 2 Bumper mounting screws, left side 2. Remove the eight screws along the bottom of the bumper. Figure 3 Figure 3 Lower bumper mounting screws Remove 2 screws in rear of bumper Remove 8 screws in bottom of bumper (4 per side) WARN INDUSTRIES PAGE 4 73465 A0 3. Lift the hood and remove the two screws from the top of the grille. Retain the hardware for use later. Figure 4 Figure 4 Grille fasteners 4. Remove the two plastic fasteners from the top of the grille. Retain the hardware for use later. Carefully pry the center pins up before removing the fasteners. Figure 5 Figure 5 Left grille fastener removal 5. Pull the grille free of the retaining clips with a “sharp” pull. Remove 2 screws Remove 2 plastic fasteners (1each side) Lift center pin then pry fastener out WARN INDUSTRIES PAGE 5 73465 A0 6. Remove five plastic fasteners from the top of the bumper. Two are behind the upper bumper support. Figure 6 Figure 6 Bumper fasteners 7. Pull the bumper corners free by pulling the ends rearward and out. The top of the bumper is snapped into plastic clips just below the fender corners, in front of the flares. Pull the bumper free. Figure 7 Figure 7 Left bumper end removal Remove 5 plastic fasteners (2 behind bumper not shown) WARN INDUSTRIES PAGE 6 73465 A0 8. Remove the two screws that hold each plastic mounting block in place and remove the blocks. Figure 8 Figure 8 LH bumper mounting block 9. Remove the three screws and remove the upper bumper support. Figure 9 Figure 9 Upper bumper support Remove 2 screws and remove plastic block Remove 3 screws Do not remove the nuts on top Bumper mounting block Upper bumper support WARN INDUSTRIES PAGE 7 73465 A0 10. Remove the 8 hex flange nuts and remove the bumper beam. Retain the hardware for bumper installation. Figure 10 Figure 10 Bumper beam, left side shown 11. Remove the four screws and remove the skid pan. Retain the hardware for reinstallation of the skid pan. Figure 11 Figure 11 Skid pan 12. Remove the molded plastic inner fender extensions by clipping or drilling out the rivets holding them to the bottom of the inner fenders. Figure 12 Remove 4 fasteners to remove skid pan Remove 4 flange nuts per side Bumper beam WARN INDUSTRIES PAGE 8 73465 A0 Figure 12 Left side fender extension 12. Locate the 1″ hole in the side of the frame behind the body mount. Drill a 1/2″ hole through the center into the inner wall. The Spacer Tube may be used as a centering tool. Repeat for opposite side. Figure 13 Figure 13 Outside left frame rail 13. Hold the Lower Frame Bracket in position and insert a 12mm bolt with 1/2″ lock washer and flat washer through the bottom hole in the Bracket and into the threaded hole in the frame. Do not tighten yet. Figure 14 Drill ½” hole through center of existing hole into inner frame wall Clip or drill rivets to remove fender extension Fender extension WARN INDUSTRIES PAGE 9 73465 A0 14. Slide a 1/2″ flat washer and Spacer Tube over a 1/2 x 4″ bolt and insert through the Lower Frame Bracket and Frame. Install 1/2″ lock washer and hex nut. Do not tighten yet. Figure 14 15. Slide an Upper Frame Bracket above the frame rail along the inside of the Lower Frame Bracket. Align the holes and insert two 7/16 x 1 1/2″ bolts through the holes and install a lock washer and hex nut on each. Do not tighten yet.

Related Content:

how to remove 03 sequoia rere bumper, fj cruiser front bumper removal, romoving rear bumper on mazda 6, removed 2012 mazda 3 bumper, remove rear bumper 2005 camry, remove lower bumper r350, removal of rear bumper 2003 ford explorer, removal of fj cruiser lower grill, rear bumper of 07 corolla removal, plasitic piece under carraige nissal altima

2007 Toyota Camry Rear Bumper Removal and Replacement Manual

0

Filed Under (Toyota Manuals) by admin on 26-01-2012

download
REMOVAL 1. REMOVE REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws and 2 clips. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. 2. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler ) a. Remove the 4 screws, 2 clips, 3 nuts and rear floor board. 3. REMOVE REAR BUMPER ASSEMBLY (w/Rear Lower Spoiler ) a. Put protective tape around the rear bumper assembly. b. Using a screwdriver, open the 2 rear bumper plates. HINT: Tape the screwdriver tip before use. c. Remove the 6 screws. d. Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration. HINT: Use the same procedures for the RH side and LH side. e. Remove the rear bumper assembly. INSTALLATION 1. INSTALL REAR BUMPER ASSEMBLY (w/o Rear Lower Spoiler ) a. Engage each claw.

Related Content:

2005 F250 Ford Truck rear brake backing plate, how to remove rear bumper 2008 camry, time it takes to repair front bumper for 2007 toyota camry

2006 HONDA CR-V CARGO COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 12-10-2011

download
INSTALLATION Installing the Cargo Cover 1. Open the tailgate. Using a flat-tip screwdriver, remove the panel covers from the right and left rear side trim panels. SUPPLIES REQUIRED Flat-tip screwdriver Clean soft cloth Cargo cover 2 Adhesive tapes 2. Using a clean soft cloth, clean the areas where the panel covers were removed. Remove the adhesive backings from the adhesive tapes, and attach the tapes to the right and left, rear side trim panels where the panel covers were removed. 3. Insert the left end of the cargo cover into the recess in the left rear side trim panel; compress the cargo cover, and insert the right end into the recess in the right rear side trim panel as you release the cover 4. Attach the four front roll cover hooks to the rear seat headrest posts as shown. 5. Slide both ends of the rear roll cover rod into the recesses in the rear side trim panel. Storing the Cargo Cover 6. Insert the right end of the cargo cover into the recess in the right rear side trim panel; compress the cargo cover, and insert the left end into the recess in the left rear side trim panel by compressing the cargo cover, and aligning the end with the recess in the left rear side panel. USE AND CARE •The front roll cover cannot be used when the rear seat is stored. •Do place cargo on the front and rear roll covers. •Do not hang anything from the roll cover hooks. REAR SEAT HEADREST ROLL COVER HOOKS (4) HEADREST STAY CARGO COVER CARGO COVER ROLL COVER ROD

Related Content:

2011 gmc terrain headrest dvds, 2012 honda civic coupe undercarriage cover, 5r55e transmission servo cover blew out AND DAMAGED CASE case, ford 6 0 hpop valve cover torque specifications, install fj cruiser cargo cover

2007 TOYOTA FJ CRUISER TOWING HITCH Installation Preparation

0

Filed Under (Toyota Manuals) by admin on 29-10-2011

download
1. Prepare for Installation. (a) Verify kit contents (b) Wear safety glasses. (c) Raise vehicle. (d) Caution muffler might be hot NOTE: Apply masking tape to quarter panels above the bumper fascia. To prevent damage when removing the bumper fascia, apply masking tape on the underside of the bottom left- hand corner of the door and left hand upper corner of door. (Fig. 1-1) 2. Prepare Vehicle for Rear Bumper Fascia Removal. (a) Open rear door (Fig. 2-1). (b) Protect exhaust tip with a rag or protective tape during installation of hitch. (Fig. 2-1) NOTE: If the vehicle is equipped with proximity sensors, detach the sensor wire connector from inside the fascia, behind the rear wheels on both sides of the vehicle (Fig. 2-2). Fig.2-1 Fig.2-2 Masking Tape Fig. 1-1 TOYOTA FJ CRUISER 2007 – TOWING HITCH Section II Installation Procedure Page 3 of 6 pages Issue: B 03/01/06 3. Remove Rear Bumper Fascia. NOTE: Protect rear bumper to prevent damage from tools (i.e. air tools) when removing the fascia bolts. (a) Remove the 13 6 mm hex head bolts (A) from rear bumper fascia. (Fig. 3-1) (b) Remove one (1) push pin (B) from fascia (Fig. 3-1) (c) Unsnap the sides of the fascia from the vehicle. (Fig. 3-2) (d) With one person on each end, remove fascia from vehicle. Store in a safe place to avoid damage during installation. (Fig. 3-2) 4. Install Hitch. (a) Install one (1) M12 x 45 bolt into the 13 mm hole as shown (Bolt 1). (Fig. 4-1) (b) Install two (2) M12 x 45 bolts in the lower slots (Bolts 2 & 3). (Fig. 4-1) (c) Install three (3) M12 x 45 bolts in the 15mm holes (Bolts 4 to 6). (Fig. 4-1) Fig. 4-1 – 3/8″ socket wrench – 17 mm socket – 6″ extension 3

Related Content:

08921-35870, Toyota FJ Cruiser tow hitch install

2005 TOYOTA AVALON TVIP V4 (REMOTE ENGINE STARTER) INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 26-03-2012

download
TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 2 of 33 pages Issue: C 02/02/05 Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Visassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Vehicle Disassembly. (a) Remove the negative battery cable. (Fig. 1-1) (1) Protect the fender before starting. (2) Do not touch the positive terminal with any tool removing the cable. (b) Remove the glove box under-dash cover. (Fig. 1-2) (c) Remove the passenger’s step cover. (Fig. 1-3) Fig. 1-1 10mm Wrench Negative Battery Cable Battery Step Cover Fig. 1-3 Nylon Panel Removal Tool Fig. 1-2 Under-Dash Cover Nylon Panel Removal Tool TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 3 of 33 pages Issue: C 02/02/05 (d) Remove the passenger’s cowl cover. (Fig. 1-4) (1) Remove one nut securing the cowl cover. (e) Remove one screw and one bolt from the glove box assembly. (Fig. 1-5) (f) Remove the glove box assembly. (Fig. 1-6) (1) Open the glove box door and remove three screws securing the glove box assembly. (2) Disconnect the trunk opener cancel switch from the glove box assembly if equipped. For vehicles with Smart Entry, the disassembly process ends on Step f. Go to Section 5. For vehicles without Smart Entry, continue the disassembly process. FOR VEHICLES WITHOUT SMART ENTRY SYSTEM ONLY. (Step g) NOTE: Do not perform this step if the vehicle has Smart Entry. (g) Remove the driver’s step cover. (Fig. 1-7) Screw Fig. 1-5 10mm Wrench, Phillips Screwdriver Bolt Glove Box Assembly Cowl Cover Fig. 1-4 Nut Fig. 1-6 Nylon Panel Removal Tool, Phillips Screwdriver Screws (x3) Glove Box Assembly Trunk Opener Cancel Switch Connector Fig. 1-7 Step Cover Nylon Panel Removal Tool
TOYOTA AVALON 2005 – TVIP V4 (REMOTE ENGINE STARTER) Procedure Page 4 of 33 pages Issue: C 02/02/05 FOR VEHICLES WITHOUT SMART ENTRY SYSTEM ONLY. (Steps h-l) NOTE: Do not perform this step if the vehicle has Smart Entry. (h) Remove the driver’s cowl cover. (Fig. 1-8) (1) Remove the one nut securing the cowl cover. (i) Remove the hood release cable. (Fig. 1-9) (1) Do not bend the hood release cable. (j) Open the screw cover on the lower dash cover. Insert the tip of a Nylon Panel Removal Tool in the upper slot to loosen it. (Fig. 1-9) (1) Remove one screw and one bolt securing the lower dash cover. (k) Remove the lower dash cover. (Fig. 1-10) (1) Disconnect the temperature sensor (connector and aspirator hose) from the lower dash cover if equipped. (l) Carefully remove the driver side airbag assembly. (Fig. 1-11) (1) Remove four bolts securing the driver side airbag assembly. (2) Be careful not to get cut by the sharp metal edges. (3) Do not disconnect the airbag assembly. (4) Use the empty V4 kit box to support the airbag assembly on the floor

Related Content:

Prius upper glovebox door hinge, Prius repair glovebox door, toyota venza glove compartment box, how to take the back off a blu dask 3 5, colbalt where is the strarter located, 2005 toyota tacoma airbag fuse location, 2005 toyota corolla under carriage, clicking noise by glove box 2008 chevy impala, loud clicking noise in glove box impala, PICTURE OF GLOVE BOX LOWER BRACE ON CHEVY UPLANDER

2007 HONDA CIVIC SI REAR UNDER SPOILER INSTALLATION INSTRUCTIONS

0

Filed Under (Honda Manuals) by admin on 05-10-2011

download
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” NOTE: •Be careful not to damage the rear bumper and body paint finish. •This rear under spoiler kit should be installed only if the ambient air temperature is 60°F (15°C) or above. •To allow the adhesive to “cure,” do not wash the vehicle for 24 hours. 4 Self-tapping screws Template Clip Rubber washer 2 If the vehicle is equipped with a rear inner fender, go to step 7; if not, continue with step 5. 5. Using a drill, drill one 3 mm hole through the lower dimple on the rear bumper on each side. • After drilling, remove any burrs from the edges of the holes with a file. DIMPLED AREA 1. Attach the template to the arched section of the rear bumper. Secure the template with strips of tape. 4. Using a hacksaw blade, cut the rear bumper along the lines you made. • After cutting, remove any burrs from the edges of the cut section. REAR BUMPER Cut out the marked area. TEMPLATE (Remove.) DRILL STOP 2. Mark the rear bumper along the outer edge of the template with a felt-tip pen, and lightly center- punch the four marks on the template. 3. Remove the template. While wearing eye protection, drill a 10 mm hole through each mark you just made. • Using a drill stop on the end of each bit, first drill with a 3 mm drill bit, and finish with a 10 mm drill bit. DRILL (3 mm 10 mm DRILL BIT) CENTER- PUNCH REAR BUMPER FELT-TIP PEN TEMPLATE REAR BUMPER TAPE 10 mm DRILL (3 mm DRILL BIT) MARKS (4) MARKS (4) HACKSAW BLADE

Related Content:

Clausing 20 Drill Press Manual, Clausing Drill Press Manual Download

2007-2010 Toyota Camry Hybrid Vehicles Potential Floor Mat Interference with Accelerator Pedal

0

Filed Under (Toyota Manuals) by admin on 18-04-2012

download
The owner notification will commence in early February, approximately one week after your dealership has been notified. This campaign will be launched in phases. • The first phase will include certain 2007 through 2010 model year Camry and Camry Hybrid vehicles equipped with Denso accelerator pedals. These owner letters will be mailed over a period of several weeks. • Additional models, including Camrys equipped with a CTS accelerator pedal will be launched in later phases as the remedy is developed. • Information on additional phases related to Camry (equipped with a CTS accelerator pedal), Avalon, Corolla, Highlander, Matrix, Prius, Tacoma, Tundra and Venza will be provided prior to the launch of these phases. If your dealership is contacted by an owner of a Denso pedal equipped Camry who has not yet received a notification, please verify eligibility by confirming through Dealer Daily/TIS prior to performing repairs . Dealers should perform the repair as outlined in the attached Technical Instructions. 2. Vehicles in Dealer Stock • As required by Federal law, dealers are not to deliver any new vehicles in their inventory, which are involved in a safety recall unless the defect has been remedied. However, because this defect does not exist in vehicles in which the driver’s side floor mat is compatible with the vehicle and properly secured you may continue to sell new vehicles (with Denso pedals) that have not received the full remedy if you assure the driver’s position floor mat is semi-permanently secured or place the front driver’s and passenger’s floor mats in the trunk on any vehicles in stock prior to sale or lease. Vehicle safety recall completion can be verified through TIS. • In order to assure established customers receive priority for the safety recall, we request that this campaign remedy be performed on in-stock Camry and Camry Hybrid vehicles just prior to vehicle delivery where possible. • A VIN list containing vehicles in dealer stock will be provided shortly

Related Content:

2010 camry service manual, 2010 F150 Owners Manual PDF, 2010 toyota venza owners manual, repair manual 2007 camry, Toyota Camry lift points

2007 Chevrolet Impala V6-3.9L – A/T 4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration

0

Filed Under (Chevrolet Manuals) by admin on 16-06-2011

download
This service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover ( Channel Plate ) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, other gaskets not included in this service kit will also be needed to complete the repair – a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering gasket kit 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to-Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve

Related Content:

2003 chevy impala transmission solenoid repair manual, 2007 impala transmission pressure solinoid

Related Content:

how to remove chevy sonic front bumper, INSTALLING A FRONT BUMPER ON THE TOYOTA RAV 4, replacing front bumper end cap on 2012 Toyota FJ cruiser, 2004fordf150frontbumperdiagram, 2000 4runner step bumper rear chrome install instructions, remove back bumper on kia sedona cover, remove back bumper on kia sedona, remove 2006 toyota matrix rear bumper, rear fender for 2008 camry, you tube remove rear bumper camry 2000