how to replace a 2001 buick lesabre front axle

You search PDF repair manual about how to replace a 2001 buick lesabre front axle, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to replace a 2001 buick lesabre front axle Direct Download speed 5432 Kb/s

  how to replace a 2001 buick lesabre front axle Full Version speed 8172 Kb/s



1997 Jeep Grand Cherokee Laredo 7 1/8″, 7 1/3″, 7 9/16″, 7 4/5″, 8 1/4″, 8 1/2″ & 8 9/10″ Ring Gears Removal And Installation Manual

0

Filed Under (Jeep Manuals) by admin on 04-07-2012

download
Removal (Model 194, 8 1/4″ & 1998 Grand Cherokee 216 Axles) 1. Raise and support vehicle. Remove rear wheel(s). If equipped with drum brakes, remove brake drum. If equipped with disc brakes, remove brake caliper and rotor. On all models, clean axle housing cover. Loosen cover bolts, and drain oil. Remove cover. 2. Remove differential pinion-shaft lock bolt. Remove pinion shaft from differential. Push in axle. Remove “C” clip from axle at pinion gear. Remove axle from tube. Remove axle shaft seal and bearing from axle tube. Installation 1. Grease bearing, and install into axle tube. Ensure bearing part number is facing outwards. Apply wheel bearing grease to axle shaft seal. Install seal in axle tube. Install axle shaft. 2. Install axle “C” clip. Pull axle out to seat “C” clip. Install pinion shaft. Install lock bolt, and tighten to specification. Apply RTV to axle housing cover. Tighten cover bolts to specification. See TORQUE SPECIFICATIONS table. Fill with gear oil. Removal (Model 198, 1999 Grand Cherokee 216 & 226 Axles) 1. Raise and support vehicle. Remove rear wheel(s). Remove brake drum. Remove nuts securing axle retainer plate to axle tube, and discard. Using slide hammer and Adapter (6790), remove axle shaft from axle tube. 2. Using a 3/8″ drill bit, drill a shallow hole into bearing retaining ring on axle. DO NOT drill into axle. Using a cold chisel, cut bearing retaining ring across drilled hole, and remove from axle shaft. Using a press and Bearing Remover (1130), remove bearing from axle shaft. Remove seal and retainer plate from axle shaft. Installation 1. Ensure axle shaft retaining plate is flat and not warped. Install retaining plate on axle shaft. Apply wheel bearing grease to axle shaft seal. Install seal on axle shaft. Grease bearing, and install on axle shaft with outer surface groove facing seal. 2. Using press and Bearing Installer (7913), press bearing onto axle shaft. Press NEW bearing retainer ring onto axle shaft. Install axle shaft in axle tube. Tighten NEW axle retainer plate nuts to specification. See TORQUE SPECIFICATIONS table. PINION SEAL & YOKE Removal

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, Silverado Rear Axle Seal Replacement, Meritor Axle Nut Torque Specs, how to remove right front axle 95 bronco, exploded view 1996 jeep grand cherokee exploded view of front suspension, size axle nut 2005 explorer, 2005 dodge magnum how to replace rear axle hub, 2002 ford expedition trailing arm torque specs, replace shaft seal in AT 2006 Avalon, remove right side axle on a 2001 toyota sienna

1991 Infiniti G20 AXLE SHAFTS – FRONT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Infiniti Manuals) by admin on 13-02-2012

download
REMOVAL & INSTALLATION FWD AXLE SHAFT Removal (Axle Shaft) 1. Raise and support vehicle. Remove front wheel assembly. Remove wheel bearing lock nut. Remove brake caliper, and support aside. Remove brake rotor. 2. Disconnect tie rod end. Remove upper knuckle nut, and separate knuckle assembly from third link assembly. Push axle shaft through hub, and separate axle assembly from knuckle assembly. 3. Insert screwdriver blade between transaxle case and right axle inner CV joint. Pry out on joint until joint pops free. Use care not to damage axle boot or axle seal. 4. On M/T vehicles, remove left axle in same manner. On A/T vehicles, insert screwdriver through differential, and drive axle out of transaxle case using a hammer. See Fig. 2 . PROBLEM Possible Cause/Action GREASE LEAKING Ripped CV Boot Replace Boot CLICKING NOISE WHILE CORNERING Dry/Worn CV Joints Replace Outer CV Joints CLUNK ON ACCELERATION Dry/Worn CV Joints Replace Inner CV Joints Worn Transmission Gears/Bearings Inspect Transmission VIBRATION/SHUDDER ON ACCELERATION Dry/Worn CV Joints Replace CV Joints Alignment Out Check Alignment Incorrect Spring Height Check Spring Height SQUEALING OR HUMMING Dry/Worn CV Joints Lube/Replace CV Joints Faulty Wheel Bearing Replace Wheel Bearing NOTE: DO NOT allow brake caliper to hang from brake hose. CAUTION: Use care not to damage pinion mate shaft or side gear while driving out axle. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 2
Fig. 2: Removing Left Drive Axle (A/T Vehicles) Courtesy of NISSAN MOTOR CO., U.S.A. Removal (Outer CV Joint) 1. Remove and discard boot bands. Slide boot off joint housing. Thread wheel bearing lock nut onto joint. Using a slide hammer and bearing puller, remove joint from axle shaft. See Fig. 3 . NOTE: Outer joint cannot be disassembled. Remove and inspect joint and replace if damaged or worn. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 3 2. Remove circlip from end of axle, and remove boot. If boot is being reused, take care not to cut boot on axle splines during removal. Clean CV joint in suitable solvent. Inspect components, and replace joint if necessary.

Related Content:

1991 ford ranger manual, shopmanuel for 1991 chevy cavalier, car manual for 1991 lexus ls400, how do i remove cv shaft on 1996 infiniti g20, snap and pop from axel when cornering in silverado, transaxle play in Nissan sentra

1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

0

Filed Under (Buick Manuals) by admin on 11-02-2012

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

Related Content:

how to remove trumpet off of ford 2000 tractor, steering pressure hose replacement f250 - 7 3 - 4wd, 99 buick park ave radiator installation, Rav 4 steering rack dismantle and refit procedure, how to replace 2003 impala power steering pump, exploded view of a tilt steering column for 2001 plymouth neon 2 0l, schematic for 99 taurus power steering, 98 amigo isuzu how to remove power steering pump, how to change power steering pump 2009 acada, youtube replace the hub on a meritor ff981 axle

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

0

Filed Under (More Manuals) by admin on 07-07-2012

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

Related Content:

2007 buick lacrosse window relay, chevy hhr evap, bypass anti-theft 2007 silverado, 2007 kia rio service manual, 200lolds aleroraditor system, schematic for front brakes on 2005 Buick Rendezvous, 4t65e service manual online, w584a lincoln, 2007 Chevy Colorado Gas Tank Seal replace, pontiac 2007 g6 remove radiator cover

FORD F450/ 550 SUPER DUTY CHASSIS CABS OWNERS MANUAL

0

Filed Under (Ford Manuals) by admin on 21-05-2012

download
LATERAL CONTROL ROD AXLE BRACKET INSTALLATION 1. Remove and discard the OEM shock absorbers, but retain the mounting fasteners (bolts & nuts) for re-use. 2. Remove the top d-bushing mount bolts and disconnect the axle breather tube (See Figure 2- 1). 3. If the truck is equipped with an S110 4.25″ X 4.25″ square axle (most F450s and F550s), install both axle spacer tabs on the axle bracket using (4) 1/2 x 1 1/4 UNC FLANGE BOLTS and (4) UNC TOP LOCK FLANGE NUTS. (See Figure 2-2). 4. Loosely fasten the axle bracket to the axle as shown in Figure 2-3 using (2) M12 x 1.75 x 40 METRIC BOLTS and (2) 1/2″ WASHERS. 5. Reconnect the axle breather tube to the axle. LATERAL CONTROL ROD (LCR) FRAME BRACKET INSTALLATION 1. On the PASSENGER side, remove to two top rivets from the OE bumper bracket and ream the holes to 0.47″ (See Figure 3-1) 2. Install the frame bracket as shown in Figure 3-2 using (4) 7/16 UNC TOP LOCK FLANGE NUTS. FIG. 3-2 Frame bracket Remove these two rivets and ream to 0.47″ DRIVER SIDE DISASSEMBLY 1. With weight taken off the rear springs, as noted in pre-installation checklist, remove the rear leaf spring hanger. Removal of the rear overload spring bracket is optional See Figure 4-1. 2. Remove the front spring hanger bracket and the front overload spring bracket. (See Figure 4-2). 3. Remove existing U-bolts that attach the axle to the leaf spring and keep the OE U-bolt plate for later use. (See Figure 4-3) After this is done, the axle, spring, and hanger will be loose. Remove and discard the spring and hangers from the axle.DRIVER SIDE ASSEMBLY 1. Review Figure 5-1 & Figure 13-2 to acquaint yourself with the various parts of the UltraRide suspension. 2. Fasten the Front Hanger to the frame using (6) 9/16 x 1-1/2 UNF BOLTS, (6) 9/16 UNF NUTS, and (12) 9/16 FLAT WASHERS. Route the parking brake cables through the corresponding holes on the Front Hanger. 3. Assemble the Suspension Arm to the axle using (2) M20 X 2.50, 79 X 425 METRIC U- BOLTS, (4) M20X2.5 METRIC NUTS, and original OE top plate and axle bracket. Make sure the arm/axle locating pin is properly inserted into the mating hole on the axle pad and that the bottom side of the arm rests evenly on the axle pad. 4. Insert the Bolt Spacer Tube into the arm bushing and loosely fasten the arm to the front hanger using (1) 3/4 X 7 UNF BOLT, (1) 3/4 UNF NUT, (2) 3/4 WASHERS, and (2) plastic wear washers. 5. Loosely fasten the Lateral Control Rod Axle Bracket to the Arm using (2) 1/2 X 1-1/4 UNC FLANGE BOLTS (See Figure 5-2). 6. Bolt the Air Spring Bracket Assembly to the frame using (5) 1/2 X 1-1/4 UNC FLANGE BOLTS and (5) 1/2 UNC TOP LOCK FLANGE NUTS. One frame hole will need to be reamed to 0.53″ on each side. See Figure 5-2. 7. Bolt the Air Spring to the Suspension Arm using (1) 1/2 UNC JAM NUT. Make certain the air spring is not twisted or creased after tightening the nut.

2004 Buick LeSabre Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Service Manual

0

Filed Under (Buick Manuals) by admin on 04-02-2012

download
Correction 1. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary: 2. Set the tire pressure to 30 psi (205 kPa) COLD. Subject: Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) • Missing balance weights • Bent rim flange • Irregular tire wear • Incomplete bead seating • Tire irregularities • Mud/ice build-up in wheel • Stones in the tire tread © 2009 General Motors Corporation. All rights reserved 3. Road test the vehicle with the Electronic Vibration Analyzer (EVA) essential tool for a sufficient distance on a known, smooth road surface to duplicate the condition. Record the Hertz (Hz) reading as displayed by the EVA onto the tire data worksheet found at the end of this bulletin. This should be done after a tire break-in period of at least 10 miles (16 km) at 45 mph (72 km/h) or greater, in order to eliminate any possible tire flat-spotting. 4. If the road test indicates a shake/vibration still exists, check the imbalance of each tire/wheel assembly on a known, calibrated, off-car dynamic balancer. If any assembly calls for more than ¼ ounce on either rim flange, remove all balance weights and rebalance to as close to zero as possible. Important: Some GM dealers may have a Hunter GSP9700 Road Force Balancer, or a Coats XR1850 Runout Balancer. Either will simplify Step 5 by not requiring dial indicators. If a Hunter GSP9700 machine is available, it may also be used to measure the radial force of the tire/wheel assembly. A guideline here is 18 lbs or less. 5. While on the balancer, measure wheel runout. If radial or lateral runout exceeds .020 in (0.50 mm) for aluminum wheels (.030 in (0.76 mm) for steel wheels), replace the wheel. 6. After confirming wheel balance and wheel runout, if any changes were made, road test the vehicle again. 7. If the smooth road shake/vibration still exists: Important: THE CONTROL ARMS SHOULD ONLY BE INSTALLED ON VEHICLES IF, AFTER THE TIRE AND WHEEL DIAGNOSIS AND REPAIRS HAVE BEEN PERFORMED, THE VIBRATION CONDITION STILL EXISTS. 8. Replace both lower control arms on vehicles built prior to the following VIN breakpoints. On Aurora, Bonneville, DeVille, Park Avenue, Park Avenue Ultra and Seville models, a newly developed hydro-bushing lower control arm with improved damping characteristics has been released. This control arm is not used on the LeSabre. The new lower control arms may provide an incremental improvement to the vehicle ride. Customers who have become “tuned in” to the shake condition may still feel some shake in the vehicle after the new lower control arms are installed. Refer to Lower Control Arm Replacement in SI (refer to the Parts Information table below for SI document ID numbers) . Important: The completed worksheet must be attached to the hard copy of the repair order. • If a Hunter GSP9700 Road Force/Balancing machine is used, record radial force variation (RFV) on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies read more than 18 lbs, match mount the tire to the wheel to get below 18 lbs. Readings of 12 lbs or less are preferable for sensitive customers. • If a Coats XR1850 Runout/Balancing Machine is used, record radial runout of the tire/wheel assemblies on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies are more than .040, match mount the tire to the wheel to get below .040. Readings of .030 inch or less are preferable for sensitive customers. • If the RFV or runout cannot be reduced to an acceptable level, replace the affected tire(s) under the guidelines of the GM Tire Warranty. • The screened tire program is only available for the General branded tires used on the Buick LeSabre. Complete the tire request form at the end of this bulletin and fax to Continental/General. • Road test the vehicle to ensure the shake/vibration has been eliminated

Related Content:

buick terraza hub removal, 2005 buick century code p0455, hunter 9700 user manual, 2000 buick lesabre custom manual, how to change the lower control arms on a 2005 Titan pdf, hunter lift L401, integrated wheel end FOR F150, location of fuses and relays 2003 buick park avenue, Rear Tire wear Mecury Mariner, repair manual on 2001 cadi deville on motor mount

1994 Nissan Maxima SE FWD Axle Shafts Removal And Installation Manual

0

Filed Under (Nissan Manuals) by admin on 21-05-2011

download
FWD AXLE SHAFT Removal 1. Raise and support vehicle. Remove wheel. Remove wheel bearing lock nut from end of drive axle. Remove disc brake caliper and suspend out of way. DO NOT allow caliper to hang by hydraulic hose. 2. Separate tie rod end from steering knuckle. Remove axle shaft from steering knuckle hub using a soft mallet. On models with ball and cage type right axle shaft, remove support bearing retainer-to-block bolts. See Fig. 4 . 3. On all models, pry right axle shaft from transaxle using screwdriver. See Fig. 1 . On M/T models, pry left axle shaft from transaxle using screwdriver. On A/T models, insert screwdriver through right axle shaft hole in differential, and drive out left axle shaft. See Fig. 2 1. Place axle shaft in soft-jawed vise with inner joint facing up. Remove boot clamps. See Fig. 4 . Mark slide joint housing and inner race in relation to axle shaft for reassembly reference. 2. Remove and discard snap ring “A”. See Fig. 3 and Fig. 4 . Remove slide joint housing. Remove snap ring “C”. Remove cage, inner race and balls as an assembly. Remove snap ring “B”. Cover axle shaft splines with tape. Remove boot. 3. To disassemble support bearing and retainer assembly on right axle shaft, remove dust shield and snap ring “D”. See Fig. 4 . Press axle shaft out of support bearing and retainer assembly. Remove snap ring and dust shield from retainer. Using bearing driver and hammer, drive support bearing out of retainer.

2009 Toyota Corolla AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION MANUAL

0

Filed Under (Toyota Manuals) by admin on 07-07-2012

download
INSTALLATION 1. INSTALL FRONT AXLE HUB BEARING 2. INSTALL FRONT DISC BRAKE DUST COVER (a) Install the disc brake dust cover to the steering knuckle with the 3 bolts. Torque: 8.3 N·m (85 kgf·cm, 73 in·lbf) 3. INSTALL FRONT AXLE HUB SUB-ASSEMBLY 4. INSTALL FRONT AXLE HUB HOLE SNAP RING Last Modified: 4-24-2008 5.1 A From: 200712 Model Year: 2009 Model: Corolla Doc ID: RM000001IWX00ZX Title: AXLE AND DIFFERENTIAL: FRONT AXLE HUB: INSTALLATION (2009 Corolla) (a) Using SST and a press, install a new front axle hub bearing to the steering knuckle. SST: 09950-60020 09951-00720 SST: 09950-70010 09951-07100 (a) Using SST and a press, install the front axle hub sub-assembly. SST: 09608-32010 SST: 09950-60010 09951-00600 SST: 09950-70010 09951-07100 5. INSTALL FRONT LOWER BALL JOINT 6. INSTALL FRONT AXLE ASSEMBLY 7. INSTALL FRONT LOWER SUSPENSION ARM 8. INSTALL TIE ROD END SUB-ASSEMBLY 9. INSTALL FRONT DISC 10. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY 11. TEMPORARILY INSTALL FRONT AXLE HUB NUT (a) Using snap ring pliers, install a new front axle hub hole snap ring. (a) Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly. (b) Install the front axle assembly to the front shock absorber with the 2 bolts and the 2 nuts. Torque: 240 N·m (2448 kgf·cm, 176 ft·lbf) Be careful not to damage the drive shaft boot or speed sensor rotor. Page 2of 4

Related Content:

calipers torque toyota corolla 2009, 2008 avalanche dtc code u0109, 2006 corolla front wheel hub assembly schematics, 2009 gm u0109, Repair manual hyundai accent 1 5 camshaft installation model 96, replace 2000 toyora corolla caliber bolts

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, automatic transmission adjustments for 1997 yuko, how to check tranmission fluid on 2012 kia sedona, 2005 explorer transmission exploded view, 2003 trailblazer torque converter removal, gm 4l60e band adjustment screws, 2011 crv engine whine, 1997 e450 power stroke trans mount parking brake, rf-d9br-7006-ab gear radio, 4r70w transmission rebuild manual download

1997-2005 Ford Expedition REAR AXLE NOISE REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 16-09-2011

download
5L3Z-4209-F = (9.75-Inch Ring Gear/3.73 ratio) •205-506 – Seal Protectors (Rotunda Tool) (1997-2005 F-150, 1997-2005 •W710084-S439 – Wheel End Nuts Expedition/Navigator) •390266-S100 – Differential Slave Pin Bolt (9.75? axles) NOTE 9.75 REAR AXLE HOUSINGS WERE •387426-S100 – Differential Slave Pin Bolt (8.8? REDESIGNED IN MID-1999, INCREASING FRONT axles) PINION BEARING SIZE. REPLACING RING & •4B422 – Axle Circlips PINIONS IN AN OLD-STYLE AXLE ASSEMBLY •ZC-21 – Metal Surface Cleaner WILL REQUIRE INSTALLATION OF SPACER P/N •TA-29 – Ultra Silicone Sealant YL3Z-4662-CA. SPACER IS TO BE INSTALLED BETWEEN INNER PINION BEARING AND •TA-27 – Stud and Bearing Mount Retaining COLLAPSIBLE SPACER. Compound and Sealer •F3TZ-4121-AA – Fluid Tag (REQUIRED IF FLUID THE AXLE SERVICE KITS INCLUDE THE TYPE IS CHANGED FROM FEHP DURING FOLLOWING COMPONENTS: REPAIR) •4630 – Head Bearing WARRANTY STATUS: Eligible Under Provisions Of •4628 – Head Bearing Cup New Vehicle Limited •4676 – Pinion Seal Warranty Coverage •386989-S2 – Washer (Slinger) OPERATION DESCRIPTION TIME •4621 – Tail Bearing 052303A 1997-2002 Expedition, 4.7 Hrs. 1998-2002 Navigator, •4616 – Tail Bearing Cup 1997-2004 F-150 Heritage, •4222 – Differential Bearing Cups 2004-2005 F-150: Rear •4221 – Differential Bearings Axle Noise Repair •4209 – Gear Set (includes pinion shims, pinion (Includes Time For Road nut and crush spacer) Test To Verify Concern (Beam Axle)) (Do Not Use •4209 – Instruction Sheet With 4205A Or 4205A4) NOTE 052303A 2003-2005 Expedition: 5.8 Hrs. THE KIT DOES NOT INCLUDE THE FOLLOWING Rear Axle Noise Repair ITEMS. SOME OR ALL OF THESE ITEMS WILL (Includes Time For Road BE REQUIRED TO COMPLETE THE AXLE Test To Verify Concern (Irs SERVICE, DEPENDING ON AXLE Axle)) (Do Not Use With APPLICATION/STYLE. 4010D Or 4010D4) 052303A 2003-2005 5.9 Hrs. ORDER AS NEEDED:

Related Content:

2006 odyssey p0741 code, 2005 Scion TC Manual PDF, is there a fuse for speedometer on 2005 chevy tahoe, is the voltage regulator in the alternator or pcm in a 2005 hyundai santa fe, 2005 expedition repair manual, 2005 Ford Focus Workshop Manual Download, head suction drain adapter crownline 240ex, 2005 mercury mariner carrier bearing, ford e450 repair manual torrent, 2005 nissan maxima fuse box location

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, Silverado Rear Axle Seal Replacement, Meritor Axle Nut Torque Specs, how to remove right front axle 95 bronco, exploded view 1996 jeep grand cherokee exploded view of front suspension, size axle nut 2005 explorer, 2005 dodge magnum how to replace rear axle hub, 2002 ford expedition trailing arm torque specs, replace shaft seal in AT 2006 Avalon, remove right side axle on a 2001 toyota sienna