how to replace a heater core on a 03 trailblazer

You search PDF repair manual about how to replace a heater core on a 03 trailblazer, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to replace a heater core on a 03 trailblazer Direct Download speed 5432 Kb/s

  how to replace a heater core on a 03 trailblazer Full Version speed 8172 Kb/s



2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, location of mode motor for 99 honda civic lx, 2010 f150heater fan speed issues, 2008 colbalt heater core removal, fuse for rear control panel 2006 durango, Body Control Module 2007 Silverado, 2003 durango sxt hvac blower motor resistor wiring diagram, 2005 silverado ac wiring diagram, 2001 DODGE RAM 2500 OWNERS MANUAL

2000 Chevrolet Blazer HEATER CORE Removal And Installation Procedure

0

Filed Under (Chevrolet Manuals) by admin on 20-05-2011

download
HEATER CORE Removal Procedure 1. Remove the heater/vent module. Refer to HEATER/VENT MODULE . 2. Remove the heater core access cover screws. Fig. 14: Identifying Heater Core Access Cover & Screws Courtesy of GENERAL MOTORS CORP. 3. Remove the heater core access cover. 4. Remove the heater core from the heater/vent module. Fig. 15: Identifying Heater Core Courtesy of GENERAL MOTORS CORP. Installation Procedure 1. Install the heater core to the heater/vent module Fig. 16: Identifying Heater Core Courtesy of GENERAL MOTORS CORP. 2. Install the heater core access cover. Tighten Tighten the heater core access cover screws to 1.9 N.m (17 lb in). NOTE: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Related Content:

1998 cadillac deville heater core removal, how to replace feater core 2005 nissan, HOW TO REPLACE HEATER CORE 1998 GMC SIERRA, 02 f150 4 2 6v heater hose, how to change heater core on 03 trailblazer, HOW TO REPLACE THE HEATER CORE IN A 1997 BUICK PARK AVENUE, how top remove evaporator core from a 2000 chevy cavalier/ pontiac sunfire, lincoln navigator rear heater core installation, location of rear heater core 04 suburban, need a picture of how to but on a heater core for a 1997 buick lesabre

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, automatic transmission adjustments for 1997 yuko, how to check tranmission fluid on 2012 kia sedona, 2005 explorer transmission exploded view, 2003 trailblazer torque converter removal, gm 4l60e band adjustment screws, 2011 crv engine whine, 1997 e450 power stroke trans mount parking brake, rf-d9br-7006-ab gear radio, 4r70w transmission rebuild manual download

1994 Ford Mustang A/ C Evaporator Housing Removal and Installation

0

Filed Under (Ford Manuals) by admin on 03-06-2011

download
1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed. Refer to Section 15-01 . If the vehicle doesn’t have a radio chassis , use a small screwdriver and pry radio cover finish panel out of console. 9. Flex glove compartment bin tabs inward. Drop down glove compartment (06010) assembly. Remove two console-to-instrument panel retaining screws. 10. Remove four console bracket retaining screws. Remove console panel from vehicle. 11. Remove three bolts retaining steering column opening cover (3A673) and reinforcement panel. Remove cover. 12. Remove steering column opening reinforcement by removing two bolts. 13. Remove two bolts retaining steering column opening reinforcement and remove reinforcement. 14. Remove six steering column retaining nuts (two retaining the hood release mechanism and four retaining column to lower brake pedal support). Lower steering column to floor. 15. Remove upper and lower steering column shrouds (3530) and disconnect wiring from turn signal and windshield wiper switch (13K359) . 16. Remove steering column through bolt and nut on engine compartment side of cowl panel. Remove steering column from vehicle. 17. Remove brake pedal support nut. 18. Snap out instrument panel defroster opening grille (044E82) . 19. Remove screws from speaker covers. Snap out speaker covers. 20. Remove front screws retaining RH and LH scuff plates at cowl side trim panels. 21. Remove RH and LH cowl side trim panels. 22. Disconnect wiring at RH cowl side. 23. Remove cowl side retaining bolts (one each side) . 24. Remove five cowl top screws attachments. 25. Gently pull instrument panel (04320) away from RH side of cowl panel. Disconnect speedometer cable, air conditioning controls and wire connectors. 26. Place a drain pan or suitable container under the heater water hose connections at the cowl panel. 27. Disconnect heater water hoses (18472) from heater core tubes and plug heater water hoses with suitable 5/8-inch and 3/4-inch plugs. Cap heater core tubes to prevent coolant loss from heater core (18476) during removal of heater case. 28. Remove screw retaining A/C evaporator case support bracket (19A639) to cowl top panel. 29. Disconnect vacuum supply supply hose (black) from A/C vacuum supply in engine compartment.

Related Content:

acadia remove center console panel, remove center console 2002 pontiac grand prix, how to remove center console 2001 ford escort, howtoremovecenterconsolefrom2007malibu, how to tighten the overhead console laredo, 2000 corolla shift knob, how to take a part 2007 toyota tundra center console, how to replace center console lid on toyota tundra, HOW TO REMOVE THE CENTER CONSOL COVER ON A 2011 HONDA ACCORD, remove 2005 rav4 console

2000 Ford Crown Victoria/Grand Marquis Evaporator Core Housing Removal And Installation Manual

0

Filed Under (Ford Manuals) by admin on 03-07-2012

download
Evaporator Core Housing Removal 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 . 2. Recover the refrigerant. For additional information, refer to Section 412-00 . 3. Drain the radiator so that the coolant level is below the heater core. For additional information, refer to Section 303-03 . 4. Raise the vehicle. For additional information, refer to Section 100-02 . 5. Remove the RH front wheel and tire. 6. Remove the screws from the RH fender apron and remove the fender apron. 7. Remove the nuts. 8. Lower the vehicle. 9. Remove the blower motor switch resistor. For additional information, refer to Section 412-04 . 10. Disconnect the connector. 11. Disconnect the evaporator to compressor suction line from the suction accumulator drier. For spring lock couplings disconnect and connect general procedure. For additional information, refer to Section 412-00 12. Disconnect the condenser to evaporator tube from the A/C evaporator core inlet tube. For spring lock couplings disconnect and connect general procedure. For additional information, refer to Section 412-00 13. Remove the nuts and position the purge valve and backet away from the evaporator core housing. 14. Remove the heater hoses from the heater core. 15. Disengage the connectors fom the bracket. 16. Disconnect the connector. 17. Remove the nut and reposition the wire harness away from the evaporator housing. 8 18. Disengage the harness from the bracket. 19. Remove the pin-type retainer and clip and remove the instrument panel lower insulator. 20. Fold back the carpet and remove the screw. 21. Inside the vehicle, remove the screw. 22. Remove the nuts(engine side).

1998 Chevy Truck S10/ T10 Blazer 2WD Evaporator Core Service and Repair Manual

0

Filed Under (Chevy Manuals) by admin on 14-05-2012

download
Manual A/C REMOVAL PROCEDURE CAUTION: Refer to Battery Disconnect Caution in Service Precautions. 1. Disconnect the negative battery cable. 2. Remove the right side instrument panel sound insulator. 3. Remove the instrument panel storage compartment. 4. Disconnect the passenger side SIR. 5. Remove the lower right instrument panel mounting bolt. 6. Remove the left and right front speaker grilles. 7. Remove the center instrument panel sound insulator. 8. Remove the left side instrument panel sound insulator. 9. Disconnect the park brake release cable. 10. Remove the knee bolster. 11. Remove the lower left instrument panel mounting bolt. 12. Remove the BCM. 13. Disconnect the driver side SIR. 14. Remove the instrument panel cluster. 15. Remove the radio. 16. Remove the HVAC control assembly. 17. Remove the steering column retaining retaining nuts. 18. Lower the steering column. 19. Remove the instrument panel carrier. 20. Remove the left and right cowl vent grille panels. 21. Disconnect the underhood lamp electrical connector, if equipped. 22. Remove the hood. 23. Remove the VCM. 24. Remove the coolant recovery tank. 25. Remove the heater hoses. 26. Disconnect the electrical connectors from the grille mounted lamps. 27. Remove the right front headlamp assembly. 28. Remove the front bumper. 29. Remove the right wheelhouse panel. 30. Disconnect the radio antenna cable. 31. Disconnect the electrical connector for the horn. 32. Remove the right fender. 33. Remove the evaporator case heat shield, if equipped. 34. Remove the blower motor resistor. 35. Remove the evaporator case bolts and screws. 36. Remove the accumulator. 37. Remove the condenser to the evaporator line fitting. 38. Remove the bolts which retain the evaporator case to the bulkhead. 39. Pull back lightly on the heater case to remove the evaporator case. 40. Remove the evaporator case retaining screws. 41. Disassemble the evaporator case sections, and remove the evaporator core. NOTE: If replacing the evaporator core, remove the expansion (orofice) tube and install it into the new core. INSTALLATION PROCEDURE 1. Install the evaporator core. 2. Assemble the evaporator case sections. 3. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb) . 4. Install the evaporator core assembly to the vehicle. 5. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in) . 6. Install the condenser to the evaporator line fitting. 7. Install the accumulator. 1998 Chevy Truck S10/T10 Blazer 2WD 8. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in) . 9. Install the blower motor resistor. 10. Install the evaporator case heat shield, if equipped. 11. Install the right fender. 12. Connect the electrical connector for the horn. 13. Install the radio antenna cable. 14. Install the right wheelhouse panel. 15. Install the front bumper. 16. Install the right front headlamp assembly. 17. Connect the electrical connectors to the grille mounted lamps. 18. Install the heater hoses. 19. Install the coolant recovery tank. 20. Install the VCM. 21. Install the hood. 22. Connect the underhood lamp electrical connector, if equipped. 23. Install the left and right cowl vent grille panels. 24. Install the instrument panel carrier. 25. Reposition the the steering column, and install the steering column retaining nuts. 26. Install the HVAC control assembly. 27. Install the radio. 28. Install the instrument panel cluster. 29. Connect the driver side SIR. 30. Install the BCM. 31. Install the lower left instrument panel mounting bolt. 32. Install the knee bolster. 33. Connect the park brake release cable. 34. Install the left side instrument panel sound insulator. 35. Install the center instrument panel sound insulator. 36. Install the left and right front speaker grilles. 37. Install the lower right instrument panel mounting bolt. 38. Connect the passenger side SIR. 39. Install the instrument panel storage compartment. 40. Install the right side instrument panel sound insulator. 41. Connect the negative battery cable. 42. Inspect the system for leaks.

Related Content:

2013 f250xl radio removal, 1998 dodge blower motors durango, how to remove 2011 dodge durango grill, 2008 yaris hatchback remove headliner replace antenna, Redezvous Dash Removal, 2005 buick lesabre instrument cluster removal, remove 2010 highlander radio, remove fender 2001 grand prix, 2006 frontier remove window switch panel, remove front dash on 2014 optima

1998 – 2003 Toyota Sienna SLIDING DOOR DIAGNOSTIC TIPS/ REPAIR MANUAL

0

Filed Under (Toyota Manuals) by admin on 08-07-2012

download
CONDITION POSSIBLE CAUSE COMMON REPAIR Top RollerComes Rail bent or widened condition Replace the upper slide door rail. Top Roller Comes Out of Rail Guide The stopper at the end of the rail is loose or missing. Replace the stopper as needed. Door Does Not Lock in Full Open Position Full open stop latch assembly is damaged. Replace the full open stop latch assembly. Left Door Opens Half Way Fuel door half stopper cable damaged. Adjust the cable. Replace the cable, if damaged. Difficltto Open Dirty weatherstrip. Clean all soda spills or other sticky substances that may have accumulated on weatherstrip and door. Difficult to Open Manually Inside handle release button damaged. Replace inside handle release button assembly according to TSB No. BO027-00, “Sliding Door Handle Push Button Operation”. Door out of adjustment. Adjust levelness of the door, according to Repair Manual. Dragging Open/Close Mll Running board rubs against the bottom of the sliding door. Adjust running board to proper position and assure clearance from the door. Manually Roller rails have bent or warp condition. Dirt or debris in the rails and rollers. Clean rails and rollers. Replace damaged parts. CONDITION POSSIBLE CAUSE COMMON REPAIR Creak Noise Junction block, damaged components, and other issues Refer to TSB No. BO003-99, “Sliding Door Creak Noise Reduction.” Refer to the “Common Sources of Creak Noise” section of this bulletin for additional information for sources of creak noise. Rattle or Clicking (NOT Creak Noise) Door moving when driving over bumps Rollers loose or damaged Adjust lower roller base mounting to bring door closer to body (Refer to TIS, applicable model year Sienna Repair Manual, Vehicle Exterior – Door/Hatch – “Slide Door: Adjustment”). Adjust strikers to bring door closer to the body. Inspect the latch assembly and replace, if damaged. Replace damaged rollers. Noise During Open/Close Rollers or rails are damaged and/or dirty. Inspect, clean, and/or replace as needed

Related Content:

Sienna Sliding Door Cable Replacement, 1998 sienna repair manual, how to fix g-6 door latch, how to remove a chevy tahoe bump stop, lexus door adjustment wind, toyota sienna sliding door repair manual

2002 Ford F-150 Heating and Ventilation REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 20-05-2011

download
Removal and Installation NOTE: If a heater core leak is suspected, the heater core must be pressure leak tested before it is removed from the vehicle. For additional information, refer to Section 412-00 . 1. Drain the radiator. For additional information, refer to Section 303-03A . 2. Remove the instrument panel. For additional information, refer to Section 501-12 . 3. Disconnect the heater core hose couplings. For additional information, refer to Section 412-00 . 4. Remove the A/C plenum demister adapter. 1. Remove the screw. 2. Remove the A/C plenum demister adapter. 5. Remove the screws and position aside the relay bracket. 6. Disconnect the vacuum line. 7. Remove the plenum chamber top. 1. Remove the 15 screws. 2. Remove the plenum chamber top 8. Remove the blend door assembly from the case. 9. Remove the heater core. 10. To install, reverse the removal procedure. * Lubricate the coolant hoses with coolant hose lubricant or plain water only, if needed.

1991 Infiniti G20 AXLE SHAFTS – FRONT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Infiniti Manuals) by admin on 13-02-2012

download
REMOVAL & INSTALLATION FWD AXLE SHAFT Removal (Axle Shaft) 1. Raise and support vehicle. Remove front wheel assembly. Remove wheel bearing lock nut. Remove brake caliper, and support aside. Remove brake rotor. 2. Disconnect tie rod end. Remove upper knuckle nut, and separate knuckle assembly from third link assembly. Push axle shaft through hub, and separate axle assembly from knuckle assembly. 3. Insert screwdriver blade between transaxle case and right axle inner CV joint. Pry out on joint until joint pops free. Use care not to damage axle boot or axle seal. 4. On M/T vehicles, remove left axle in same manner. On A/T vehicles, insert screwdriver through differential, and drive axle out of transaxle case using a hammer. See Fig. 2 . PROBLEM Possible Cause/Action GREASE LEAKING Ripped CV Boot Replace Boot CLICKING NOISE WHILE CORNERING Dry/Worn CV Joints Replace Outer CV Joints CLUNK ON ACCELERATION Dry/Worn CV Joints Replace Inner CV Joints Worn Transmission Gears/Bearings Inspect Transmission VIBRATION/SHUDDER ON ACCELERATION Dry/Worn CV Joints Replace CV Joints Alignment Out Check Alignment Incorrect Spring Height Check Spring Height SQUEALING OR HUMMING Dry/Worn CV Joints Lube/Replace CV Joints Faulty Wheel Bearing Replace Wheel Bearing NOTE: DO NOT allow brake caliper to hang from brake hose. CAUTION: Use care not to damage pinion mate shaft or side gear while driving out axle. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 2
Fig. 2: Removing Left Drive Axle (A/T Vehicles) Courtesy of NISSAN MOTOR CO., U.S.A. Removal (Outer CV Joint) 1. Remove and discard boot bands. Slide boot off joint housing. Thread wheel bearing lock nut onto joint. Using a slide hammer and bearing puller, remove joint from axle shaft. See Fig. 3 . NOTE: Outer joint cannot be disassembled. Remove and inspect joint and replace if damaged or worn. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 3 2. Remove circlip from end of axle, and remove boot. If boot is being reused, take care not to cut boot on axle splines during removal. Clean CV joint in suitable solvent. Inspect components, and replace joint if necessary.

Related Content:

1991 ford ranger manual, shopmanuel for 1991 chevy cavalier, car manual for 1991 lexus ls400, how do i remove cv shaft on 1996 infiniti g20, snap and pop from axel when cornering in silverado, transaxle play in Nissan sentra

2006 Ford Explorer Scheduled Maintenance Guide

0

Filed Under (Ford Manuals) by admin on 12-02-2012

download
Scheduled Maintenance: 2006 Ford Explorer Driving Condition: Normal Condition Engine Displacement Transmission Fuel Cylinders Drivetrain 4.0 L Automatic Flexible 6 RWD ded Maintenance Mileage: Every 5,000 15 30 45 60 75 90 100 105 120 135 150 Value Package Price: See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer See Dealer Change engine oil and replace oil filter (Up to 5 quarts of oil. Perform at specified mileage interval or every 6 months, whichever occurs first) – See dealer Perform multi-point inspection – See dealer Rotate and inspect tires; check wheel end play and turning noise – See dealer Inspect automatic transmission fluid level (if equipped with underhood dipstick) – See dealer Inspect brake pads/shoes/rotors/drums, brake lines and hoses, and parking brake system – See dealer Inspect engine cooling system and hoses – See dealer Inspect and lubricate all non-sealed steering linkage,ball joints,suspension joints,half and drive-shafts and u-joints – See dealer Inspect complete exhaust system and heat shields – See dealer Replace engine air filter – See dealer Replace fuel filter – See dealer Inspect 4×2 front wheel bearings; replace grease and grease seals, and adjust bearings – See dealer Change Premium Gold engine coolant – See dealer Inspect accessory drive belt(s) – See dealer Replace PCV valve – See dealer Replace spark plugs – See dealer Replace accessory drive belts (if not replaced within last 100,000 miles) – See dealer Replace rear axle lubricant – See dealer Change automatic transmission/transaxle fluid and filter – See dealer Notes: Prices are shown for illustrative purposes only and may vary based on required fluid quantities and other conditions. Information in this document is current as of January 07, 2010 and could change in the future.

Related Content:

replace radiator on hummer h3, 2006 nissan frontier cat replacement, hydraulic parking brakes on drive shaft, how to replace cat 05 frontier, how to replace an alternator on a 2006 honda pilot, how to replace a alternator on a 2006 honda pilot, how to change starter in 2006 chevy cobalt 2 2, ford explorer 2006 linkage repair, 2006 saturn ion maintenance recommendations, 2006 mercury 5 1 inboard starter smoking

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, location of mode motor for 99 honda civic lx, 2010 f150heater fan speed issues, 2008 colbalt heater core removal, fuse for rear control panel 2006 durango, Body Control Module 2007 Silverado, 2003 durango sxt hvac blower motor resistor wiring diagram, 2005 silverado ac wiring diagram, 2001 DODGE RAM 2500 OWNERS MANUAL