Skip to content

how to replace blend door actuator impala

You search PDF repair manual about how to replace blend door actuator impala, if there are search results will appear below. If search results do not exist, please search by others keyword.

1999 Chrysler Truck Town And Country Blend Door Actuator REMOVAL And INSTALLATION MANUAL

download
REMOVAL The air conditioning system can be equipped with either a standard, single blend- air door actuator, or it can be equipped with dual actuators. The dual system has separate blend-air controls. This allows for separate control of the driver’s side air, and the passenger side air. 1. Remove the lower left side steering column cover. Refer to Instrument Panel and Systems. Side View Of HVAC With Actuators Zoom Sized for Print ABS Control Module 2. Remove ABS control module. 3. Remove blend-air actuator connector. 4. Remove blend-air actuator. INSTALLATION 1. For installation, reverse the above procedures. 2. Perform the HVAC Control Calibration Diagnostic and Cooldown test. Repeating the test is necessary to clear the fault codes

1998 – 2003 Toyota Sienna SLIDING DOOR DIAGNOSTIC TIPS/ REPAIR MANUAL

download
CONDITION POSSIBLE CAUSE COMMON REPAIR Top RollerComes Rail bent or widened condition Replace the upper slide door rail. Top Roller Comes Out of Rail Guide The stopper at the end of the rail is loose or missing. Replace the stopper as needed. Door Does Not Lock in Full Open Position Full open stop latch assembly is damaged. Replace the full open stop latch assembly. Left Door Opens Half Way Fuel door half stopper cable damaged. Adjust the cable. Replace the cable, if damaged. Difficltto Open Dirty weatherstrip. Clean all soda spills or other sticky substances that may have accumulated on weatherstrip and door. Difficult to Open Manually Inside handle release button damaged. Replace inside handle release button assembly according to TSB No. BO027-00, “Sliding Door Handle Push Button Operation”. Door out of adjustment. Adjust levelness of the door, according to Repair Manual. Dragging Open/Close Mll Running board rubs against the bottom of the sliding door. Adjust running board to proper position and assure clearance from the door. Manually Roller rails have bent or warp condition. Dirt or debris in the rails and rollers. Clean rails and rollers. Replace damaged parts. CONDITION POSSIBLE CAUSE COMMON REPAIR Creak Noise Junction block, damaged components, and other issues Refer to TSB No. BO003-99, “Sliding Door Creak Noise Reduction.” Refer to the “Common Sources of Creak Noise” section of this bulletin for additional information for sources of creak noise. Rattle or Clicking (NOT Creak Noise) Door moving when driving over bumps Rollers loose or damaged Adjust lower roller base mounting to bring door closer to body (Refer to TIS, applicable model year Sienna Repair Manual, Vehicle Exterior – Door/Hatch – “Slide Door: Adjustment”). Adjust strikers to bring door closer to the body. Inspect the latch assembly and replace, if damaged. Replace damaged rollers. Noise During Open/Close Rollers or rails are damaged and/or dirty. Inspect, clean, and/or replace as needed

2003 HONDA CIVIC Door Panel Removal And Installation Manual

download
2003 CIVIC – Door Panel Removal/Installation Special Tools Required *KTC trim tool set SOJATP2014 *Trim pad remover, Snap-on A 177A or equivalent, commercially available 2-door NOTE: Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. 1. If applicable, remove the regulator handle (A) by pulling the clip (B) out with a wire hook (C). 2. Remove the inner handle (A). Take care not to scratch the door panel. 3. Remove the switch panel (A) (power window model) or the pull pocket (B) (manual window model). -1 Pry out on the upper portion of the cover (B) to release the hooks (C, D), then remove the cover. -2 Remove the screws. -3 Pull the inner handle forward and out half-way to release the hook (E). -4 Disconnect the inner handle rod (F) and power door lock switch connector (G) (driver’s side for some models). – 1 Using a trim tool, pry the cap (C), then remove the screw (D) 4. Remove the screws (H) securing the door panel. 5. Remove the mirror mount cover. 6. Release the clips that hold the door panel (A) with a commercially available trim pad remover (B), then remove the door panel by pulling it upward. Remove the door panel with as little bending as possible to avoid creasing or breaking it. 7. Install the door panel in the reverse order of removal, and note these items: *Replace any damaged clips. *Make sure the connectors are plugged in properly, and the rod is connected properly. *Make sure the window and power door locks operate properly. *If applicable, install the regulator handle so it points forward and up at a 45 º angle with the glass fully closed

2002 Chevrolet Impala Radiator Air Baffle and Deflector Replacement Manual

download
Radiator Air Baffle and Deflector Replacement – Upper Removal Procedure 1. Remove the radiator air baffle retainers. 2. Tilt the rear of air baffle upward slightly. Slide the air baffle rearward in order to disengage the upper and lower clips of the air baffle from the fascia support. 3. Remove the radiator air baffle. Installation Procedure 2002 Chevrolet Impala 1. Position the radiator air baffle to the vehicle. Tilt the rear of the air baffle upward slightly. Position the upper clip of the air baffle to the lower edge of the front fascia support C-channel. 2. Slide the baffle towards the front of the vehicle in order to completely engage the upper and lower clips of the baffle onto the fascia support. 3. Align the tabs at the rear of the air baffle to the openings in the upper radiator support. 4. Install the radiator air baffle retainers.

2002 Ford Focus L4-2.0L SOHC VIN P-Front Door Latch Removal And Installation Manual

download
Hood and Trunk Front Door Latch Service and Repair Front Door Latch Front Door Latch Notes REMOVAL 1. Remove the front door trim panel . 2. Remove the side impact energy absorption panel. 3. Remove the screw (if equipped). 4. Detach the door latch remote control. 1. Detach the handle from the door panel. 2. Detach the door latch remote control. 5. Peel back the watershield. CAUTION: Do not touch the adhesive surface as re-bonding will be impaired. 6. Disconnect the door latch actuator electrical connector. 7. Remove the exterior door handle access hole grommet from the door. 8. Loosen the screw. NOTE: The screw must be fully disengaged from the door lock cylinder bezel although it is not necessary to fully remove the screw 9. Remove the door lock cylinder bezel. 10. Remove the exterior door handle. 1. Slide the exterior door handle to release. 2. Remove the exterior door handle and gaskets. 11. Remove the screws. 12. Loosen the screw. NOTE: The screw must be fully disengaged from the exterior door handle although it is not necessary to fully remove the screw. 13. Detach the door latch. 1. Press the door latch to release. 2. Detach the door latch. 14. Detach the door latch security shield. 15. Remove the door latch and exterior door handle reinforcement plate. 16. Disconnect the door lock cylinder connecting rod. 1. Rotate the clip counterclockwise to release the connecting rod. 2. Disconnect the connecting rod. 17. Disconnect the exterior door handle reinforcement plate connecting rod.