replace blower motor resistor hyundai santa

You search PDF repair manual about replace blower motor resistor hyundai santa, if there are search results will appear below. If search results do not exist, please search by others keyword.



  replace blower motor resistor hyundai santa Direct Download speed 5432 Kb/s

  replace blower motor resistor hyundai santa Full Version speed 8172 Kb/s



2001 Dodge Durango BLOWER MOTOR RELAYS REPAIR MANUAL

0

Filed Under (Dodge Manuals) by admin on 13-02-2012

download
BLOWER MOTOR RESISTOR 1. Disconnect negative battery cable. Disconnect blower motor resistor harness connector. Using DVOM, check for continuity between all blower motor resistor terminals. If continuity exists between all terminals, go to next step. If continuity does not exist between all terminals, replace faulty blower motor resistor. 2. Check for open or short in circuits between blower motor resistor and heater control panel. Also check for open or short in wire between blower motor resistor and blower motor. BLOWER MOTOR SWITCH 2000 Dakota, 2000 Durango & 2000-01 Ram Pickup 1. Remove Power Distribution Center (PDC) cover. Using DVOM, check for battery voltage at PDC fuse No. 5 (40-amp) on Dakota and Durango; PDC fuse No. 12 (40-amp) on Ram Pickup. If battery voltage exists, go to next step. If battery voltage does not exist, check for open in Red wire between battery and underhood PDC. If Red wire is okay, replace underhood PDC. 2. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel cable, electrical and vacuum connectors as necessary. Using DVOM, check for continuity between heater control panel harness connector terminal No. 7 (Black wire on Dakota and Durango; Black/Orange on Ram Pickup) and ground. See Fig. 5 . If continuity exists, go to step 4 . 3. If continuity does not exist, repair open in Black wire or Black/Orange wire between heater control panel 2001 Dodge Durango 2000-01 HEATER SYSTEMS’ ‘RWD Trucks & Vans harness connector terminal No. 7 and ground connector located at lower right corner of instrument panel (Dakota and Durango) or behind center of instrument panel (Ram Pickup). 4. Place heater mode control knob to any position except OFF. Using DVOM, check for continuity between heater control panel terminal No. 7 and terminals No. 3, 4, 5 and 6 while rotating blower motor switch. See Fig. 5 . 5. If continuity does not exist at any terminal, replace faulty heater control panel. If continuity exists as specified, check for open in circuits between heater control panel and blower motor resistor. Also check for an open in circuit between heater control panel and blower motor. See WIRING DIAGRAMS . Fig. 5: Identifying Heater Control Panel Blower Switch Connector Terminals (2000 Dakota & Durango Are Shown; Ram Pickup Is Similar) Courtesy of CHRYSLER CORP. Ram Van/Wagon 1. Disconnect negative battery cable. Remove heater control panel. See HEATER CONTROL PANEL under REMOVAL & INSTALLATION. Disconnect heater control panel harness connectors. Using DVOM, check for continuity between heater control panel C3 harness connector terminal “C” (Black wire) and ground. See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Black wire between heater control panel and ground connector located at lower right of steering column. 2. Place heater mode control selector to any position, except OFF. Using DVOM, check for continuity between appropriate terminals of heater control panel, for C3 connector terminals “B” (Violet wire) and “C” (Black wire). If continuity exists through heater control panel, go to next step. If continuity does not exist, replace faulty heater control panel assembly. 3. Using DVOM, check for continuity between heater control panel C3 connector terminal “B” (Violet wire) and C1 connector terminal “E” (Violet wire). See Fig. 6 . If continuity exists, go to next step. If continuity does not exist, repair open in Violet wire between heater control panel C3 and C1 connectors.

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, location of mode motor for 99 honda civic lx, 2010 f150heater fan speed issues, 2008 colbalt heater core removal, fuse for rear control panel 2006 durango, Body Control Module 2007 Silverado, 2003 durango sxt hvac blower motor resistor wiring diagram, 2005 silverado ac wiring diagram, 2001 DODGE RAM 2500 OWNERS MANUAL

2005 Chevy Truck Silverado 1500 2WD Blower Motor Resistor Replacement

0

Filed Under (Chevy Manuals) by admin on 29-04-2012

download
Blower Motor Resistor Replacement Notes BLOWER MOTOR RESISTOR REPLACEMENT REMOVAL PROCEDURE 1. If equipped, remove the IP sound insulator. 2. Disconnect the electrical connection from the blower motor . 3. Disconnect the electrical connection from the blower motor resistor 4. Remove the blower motor resistor retaining screws. 5. Remove the blower motor resistor. INSTALLATION PROCEDURE 1. Install the blower motor resistor. NOTE: Refer to Fastener Notice in Service Precautions. 2. Install the blower motor resistor retaining screws. Tighten Tighten the screws to 1.6 N.m (14 lb in) . 3. Connect the electrical connection to the blower motor resistor. 4. Connect the electrical connection to the blower motor . 5. If equipped, install the IP sound insulator.

Related Content:

2005 chevy blower motor resistor ground connections, testing mazda 5 for faulty blower moror, resistor sl1, part number 05 silverado blower resistor fix, fan blower resistor for 1998 buick regal, how to change blower motor 2005 hummer h2, how to rotate resistor in schematics, NISSAN CHANGED BLOWER RESISTOR MAKING NOISE WHEN CRANK, removal/replacement of stepper motor in a 05 tahoe, removing blower motor from 2002 tundra

2004 Pontiac Grand Prix Blower Motor Inoperative or Intermittent, Blower Speed May Drop or Blower Continues to Run After Key Off (Install a Capacitor at Blower Motor Control Module Connector) Service Manual

0

Filed Under (Pontiac Manuals) by admin on 27-02-2011

download
Technicians are to install a capacitor, P/N 25073556, at the blower motor control module connector using the following procedure: 1. Disconnect the negative cable from the battery. Refer to the Battery Negative Cable Disconnect/Connect procedure in the Engine Electrical section of SI. 2. Remove the right closeout/insulator panel. Refer to the Closeout/Insulator Panel Replacement-Right procedure in the Instrument Panel, Gages and Console section of SI 3. Disconnect the wire harness connector to the blower motor control module. 4. Install a capacitor, P/N 25073556, into the blower motor control module connector using the following steps. Refer to the illustration above to locate the positive and negative leads of the capacitor. Refer to the Splicing Copper Wire Using Splice Clips procedure in the Wiring Systems section of SI (Document ID #303646) for more information on using splice clips. 5. If the customer concern was of a blower motor that continues to run after key off, then replace the blower motor control module and install the capacitor . Refer to the blower motor control module Replacement procedure in the HVAC section of SI. This condition is the only time you need to replace the blower motor control module. 6. Reconnect the blower motor control module connector. 7. Install the right closeout/insulator panel. Refer to the Closeout/Insulator Panel Replacement- Right procedure in the Instrument Panel, Gages and Console section of SI. 8. Reconnect the negative cable to the battery. Refer to the Battery Negative Cable Disconnect/Connect procedure in the Engine Electrical section of SI. 9. Verify proper operation of the blower motor.

Related Content:

replace 2002 suburban fan motor, 2004 cavalier stepper motors, Hino 268 2013 fuse box for heater, hino blower motor replace procedure, installing heaterfan motor dodge grand caravan 2011, instructions for replacing 2004 pontiac grand prix blower motor, is the resisistor built in the blower motor on a 2012 chevy sonic?, remove heat blower motor 67 grand prix, to replace an a/c motor on a 2003 civic, wireing for blower control 2004 silverado

2001-2004 FORD Taurus WATER IN THE BLOWER CASE—BLOWER MOTOR SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 14-06-2011

download
SERVICE PROCEDURE 1. Access blower motor and resistor per the Workshop Manual Sections 412-02 and 412-04. Inspect for evidence of water/corrosion. If water/corrosion are found or parts have failed, replace per Workshop Manual (blower motor 1F1Z-19805-AA and resistor F6DZ-19A706-AA). 2. Visually inspect the Cowl Vent Screen located under the RH windshield wiper to verify if the Figure 1 – Article 04-15-3 screen is fully seated. Inspect the rubber seal on the vent screen which should be fully seated 5. Locate the tape as shown (Figure 2). Remove against the windshield. If the cowl vent screen the tape and apply Clear Silicone Rubber is not fully seated and appears warped, it must TA-32 to the small hole as shown (Figure 2). be replaced (4F1Z-54018A16-BAA) 3. Remove the cowl vent screen per the vehicle model years and build date information. Workshop Manual Section 412-01 Pollen Filter Removal and inspect the cabin filter to confirm ISSUE it is fully seated. Re-seat the filter as Some vehicles built between 5/1/2001 and necessary. Inspect rain-hat base to make sure 12/15/2003 may exhibit water in the blower case or it is secure and sealed to the body. Reposition on the passenger side floor, an inoperative climate and reseal as necessary using Clear Silicone control blower motor, a motor that operates on high Rubber TA-32. speed only, and/or a blower motor resistor failure. 4. Remove the foam sealant expulsion at lower front outboard corner base of the rain-hat ACTION (Figure 1). Inspect and seal cowl area and install Rain-Hat Extension Seal. Inspect and replace blower motor and/or blower motor resistor if there is evidence of water/corrosion. Refer to the following Service Procedure for details.

Related Content:

2001 saab 9-3 shop manual, Replacing blower fan on 2008 F2 50

2002 Chrysler Voyager LX Power Windows TROUBLE SHOOTING/ SYSTEM TESTS

0

Filed Under (Chrysler Manuals) by admin on 19-11-2011

download
ALL WINDOWS INOPERATIVE 1. Check power window system circuit breaker and fuse. See TROUBLE SHOOTING . Replace components as necessary. If components are okay, go to next step. 2. Remove driver’s power window switch. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Turn ignition on. Using test light, connect ground lead to harness connector terminal No. 13 (Black/Brown wire). Check for voltage by touching test light probe to harness connector terminals No. 9, 11 and 14 (all White/Pink wires). 3. If test light does not illuminate, check power and ground circuits. See WIRING DIAGRAMS . If test light illuminates, ground circuit and power circuit between battery and switch are okay. Check switch and motor. See POWER WINDOW SWITCH and POWER WINDOW MOTOR under COMPONENT TESTS. COMPONENT TESTS VENT WINDOW MOTOR 1. Remove “D” pillar trim panel. See “D” PILLAR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power vent window motor wire connector from body harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. 5. Momentarily touch the positive (+) jumper probe to the other motor connector terminal. When the positive probe is connected, the motor should rotate in one direction to either move window open of closed. If window is all the way open or closed the motor will grunt and the crank system will flex when actuated in the one direction. Reverse jumper probes at the motor connector terminals and window should now move in the opposite position to verify full operation. If motor grunts and does not move with the motor connected in both directions, verify that crank system is not binding. POWER WINDOW MOTOR 1. Remove door trim panel and sound pad. See DOOR TRIM PANEL under REMOVAL & INSTALLATION. 2. Disconnect power window motor wire connector from door harness. 3. Using 2 jumper wires, connect one to a battery (+) source and the other to a good ground (-). 4. Connect the negative (-) jumper probe to one of the motor connector terminals. POWER WINDOW SWITCH 1. Remove window switch from door trim panel. See POWER WINDOW SWITCH under REMOVAL & INSTALLATION. Using an ohmmeter, check switch continuity. See appropriate WINDOW SWITCH CONTINUITY table. See Fig. 1 or Fig. 2 . 2. If the results are NOT OK, replace the drivers side window lift switch. 3. Test passenger door switch for continuity. 4. If the results are not OK, replace the switch. The power window master switch has a Auto-Down feature. The switch is equipped with 2 detent positions when actuating the power window OPEN. The first detent position allows the window to roll down and stop when the switch is released. The second detent position actuates an integral express roll down relay that rolls the window down after the switch is released. When the express down circuit senses stall current (window has reached end of down travel), the switch will turn current off to the motor. The AUTO feature can be cancelled by actuating the switch UP or DOWN while window is in motion. If the electronic circuit in the switch fails to detect a stall current, the auto down circuit will time out within 9 to 13 seconds.

Related Content:

starter motor repair manual, 07 yukon 4wd left side motor mount replace, How to test end coder, instructions on wiring a 350 motor, parts diagram 1990 grand prix 4 door drivers window, remove water deflector 2000 silverado window, repairing power window on 2003 ford focus, replacement of acadia thermostat, replacing window weatherstripping toyota tundra, silverado motor mount replace

2002 Ford Taurus WATER IN THE BLOWER CASE BLOWER MOTOR AND/ OR RESISTOR FAILURE REPAIR MANUAL

0

Filed Under (Ford Manuals) by admin on 30-01-2012

download
SERVICE PROCEDURE 1. Access blower motor and resistor per the Workshop Manual Sections 412-02 and 412-04. Inspect for evidence of water/corrosion. If water/corrosion are found or parts have failed, replace per Workshop Manual (blower motor 1F1Z- 19805-AA and resistor F6DZ-19A706-AA). 2. Visually inspect the Cowl Vent Screen located under the RH windshield wiper to verify if the screen is fully seated. Inspect the rubber seal on the vent screen which should be fully seated against the windshield. If the cowl vent screen is not fully seated and appears warped, it must be replaced (4F1Z-54018A16- BAA). 3. Remove the cowl vent screen per the Workshop Manual Section 412-01 Pollen Filter Removal and inspect the cabin filter to confirm it is fully seated. Re-seat the filter as necessary. Inspect rain-hat base to make sure it is secure and sealed to the body. Reposition and reseal as necessary using Clear Silicone Rubber TA-32. 4. Remove the foam sealant expulsion at lower front outboard corner base of the rain-hat (Figure 1). Zoom Sized for Print 5. Locate the tape as shown (Figure 2). Remove the tape and apply Clear Silicone Rubber TA-32 to the small hole as shown (Figure 2) Parts Block Zoom Sized for Print 6. Install the Rain-Hat Extension Seal or Shed Lip Seal 4F1Z-54022A54-AA to the outboard edge of the rain-hat (see Figure 2 for installation). The 10 mm by 10 mm (0.5″ by 0.5″) cut area, located 25 mm (1″) from the end of the seal, will face down and locate at the 90 degree bend of the rain-hat on the fender side (Figure 3). 7. Prior to installation of the cowl vent screen, verify that the cabin filter cover is properly snapped in place and the clip is located on the inboard side, (toward the center of the bulkhead), the cover will feel loose if not properly snapped in place. Reinstall the cowl vent screen per Section 412-01 of the Workshop Manual.

Related Content:

2004 ford tarus rain hat, mazda titan workshop manual

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, automatic transmission adjustments for 1997 yuko, how to check tranmission fluid on 2012 kia sedona, 2005 explorer transmission exploded view, 2003 trailblazer torque converter removal, gm 4l60e band adjustment screws, 2011 crv engine whine, 1997 e450 power stroke trans mount parking brake, rf-d9br-7006-ab gear radio, 4r70w transmission rebuild manual download

1998 Acura 3.5RL FUEL PUMP RELAY (3.5RL) INSTALLATION MANUAL

0

Filed Under (Acura Manuals) by admin on 13-06-2011

download
Fuel pump relay is located in the front of the trunk. Turn ignition switch to START position. If engine starts, go to next step. If engine does not start, go to FUEL PUMP RESISTOR (3.5RL) . 2. Turn engine off and ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is present, go to next step. If battery voltage is not present, go to step 4). 3. Start engine and run at 3000 RPM with no loads and transmission in Park or Neutral, until radiator fan comes on. Allow engine to idle for at least one minute. Turn engine off. Disconnect vacuum hose No. 21 from vacuum manifold. Apply 8-12 in. Hg (27-40 kPa) vacuum to Manifold Absolute Pressure (MAP) sensor. Start engine and run at 6500 RPM with no loads and transmission in Park or Neutral. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If less than one volt is present, fuel pump relay circuit is okay. If one volt or more is present, substitute a known good PCM, then recheck. If symptom or indication goes away, replace original PCM. 4. Turn ignition off. Disconnect PCM 26-pin and 12-pin connectors. Disconnect fuel pump relay 4-pin connector. Using a fused jumper wire, connect fuel pump relay connector terminals No. 2 (Red/White wire) and No. 4 (Green wire). Turn ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is not present, go to next step. If battery voltage is present, replace fuel pump relay. 5. Remove jumper wire. Measure voltage between ground and fuel pump relay 4-pin connector terminal No. 2 (Red/White wire). If battery voltage is present, repair open or short in Green wire between PCM and fuel pump relay. If battery voltage is not present, repair open in Red/White wire between fuel pump relay and FUEL PUMP fuse No. 22 (20-amp), located in underdash fuse/relay box. FUEL PUMP RESISTOR (3.5RL) 1. Fuel pump resistor is located in the left corner of the trunk. Disconnect fuel pump resistor 2-pin connector. Turn ignition on and measure voltage between ground and fuel pump resistor connector terminal No. 2 (Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, go to next step. If battery voltage is not present as specified, check PGM-FI relay. See PGM- FI MAIN RELAY . 2. Turn ignition off. Using a jumper wire, connect fuel pump resistor connector terminals No. 1 (Black/Yellow wire) and No. 2 (Yellow wire). Turn ignition switch to START position. If engine does not start, go to next step. If engine starts, replace fuel pump resistor. 3. Turn ignition off. Disconnect fuel unit sub-harness Gray, 10-pin connector located in front of trunk, above fuel pump access panel, next to Gray, 20-pin connector. Turn ignition on and measure voltage between ground and sub-harness connector terminal No. 7 (Black/Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, check fuel pump. If battery voltage is present as specified, repair open in Black/Yellow wire between fuel pump resistor and fuel pump

Related Content:

1998 jimmy fuel pump install, wire diagram on a 2002 grand prix headlight, 03 ford windstar fuel pump wiring, proper connection for horn relay 1968 chevelle, pcm drag adjustment, damaged fuel pump wiring, vcm ground wire, location of vent valve solenoid on 2010 ford ranger, 2005 tundra speed pulse signal wire location, 1998 s10 6 cylindes fuel regulator diagram

Windshield Wiper Linkage Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 05-04-2012

download
Installation Instructions 1. Place the Wiper Motor Mount Plate (FFR# 25391) along the edge of the ¾” shock tower support tube on the passenger side and the top of the footbox front wall aluminum. Mark the location for the riv nuts (4 total). 2. Drill the riv nut holes using a 25/64″ drill bit. You may want to begin by using a smaller drill bit to drill a pilot hole first (shown). 3 3. Intsall the 1/4″ riv nuts (4) using the supplied riv nut tool. 4. Install one of the rod ends (FFR# 25724) with the supplied jam nut (FFR# 25725) onto the wiper motor arm (1/2″, 9/16″ wrenches). You will have to trim some of the excess thread off of the rod end in order for it to have sufficient clearance between it and the wiper motor mount plate. 4 5. Place the wiper motor in the mount plate (FFR# 25391) so the pins on the motor fit inside the holes in the mount plate and the three threaded holes in the motor line up with the corresponding holes in the mount plate. 6. Using the three Corvette screws that held the motor in place, fasten the motor to the mount plate (T- 30 Torx). 7. Place a nylon spacer (FFR# 10960) between the frame and the mount plate at each of the riv nuts and bolt the plate into positon using the supplied ¼”-20 x 1.5″ long bolts (4mm allen).
6 ATTENTION: For the bolt at the front corner of the plate, you may have to use the supplied washers as well as the nylon spacer to prevent the bolt from bottoming out before the plate is firmly in place (See photo). 8. Screw the supplied section of threaded rod (FFR# 25723) into the rod end on the wiper motor. 7 9. Slide the aluminum tube (FFR# 25934) over the threaded rod and measure how much of the aluminum tube will need to be trimmed once the rod end is screwed on. Trim the tubing with a tubing cutter/hacksaw/cutoff wheel. 10. As you did with the rod end on the wiper motor, you will have to trim the threads on the rod end to clear the aluminum. 11. Place the aluminum tube over the threaded rod, then screw the rod end (FFR# 25724) onto the rod until tight. 12. Before installing the wheel box to the body you will have to trial fit the wiper arm to the wheel box. It is a tight fit, so you may have to spray the splines with some WD-40 or some oil and tap the wiper arm onto the splines. Remove the wiper arm from the wheelbox so you can bolt it to the body. 8 13. Follow the instructions in the assembly manual for bolting the wheelbox to the body. 14. Install the rod end on the wiper wheel box arm with the supplied jam nut (FFR# 25725) (1/2″, 9/16″ wrenches). 15. Install the wiper blade (FFR# 25629) onto the wiper arm (FFR# 25552). 16. Clip the wiper arm onto the shaft of the wiper wheel box, making sure that the tab on the arm clips into the channel on the wheel box shaft (clip shown). 9 17. Spray the windshield with water, or glass cleaner. Check the sweep by turning the wipers on – start with the slowest setting to avoid damaging the linkage or running the wiper beyond the windshield. Make any necessary adjustments, and the linkage installation is complete

Related Content:

how to replace a 2004 impala wiper fluid motor, how to change the wiper motor in 01 isuzu npr, install motor mount on 03 lesabre, 2002 GRAND PRIX wiper linkage, isuzu npr wiper motor replacement, isuzu npr how to replace wiper motor, need 2011 dodge journey wiper motor electrical schematic, nut plate drill motor, how to unplug the windshield wiper motor on a 2002 cadillac deville, 1983 rx-7 wiper linkage

1991 Infiniti G20 AXLE SHAFTS – FRONT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Infiniti Manuals) by admin on 13-02-2012

download
REMOVAL & INSTALLATION FWD AXLE SHAFT Removal (Axle Shaft) 1. Raise and support vehicle. Remove front wheel assembly. Remove wheel bearing lock nut. Remove brake caliper, and support aside. Remove brake rotor. 2. Disconnect tie rod end. Remove upper knuckle nut, and separate knuckle assembly from third link assembly. Push axle shaft through hub, and separate axle assembly from knuckle assembly. 3. Insert screwdriver blade between transaxle case and right axle inner CV joint. Pry out on joint until joint pops free. Use care not to damage axle boot or axle seal. 4. On M/T vehicles, remove left axle in same manner. On A/T vehicles, insert screwdriver through differential, and drive axle out of transaxle case using a hammer. See Fig. 2 . PROBLEM Possible Cause/Action GREASE LEAKING Ripped CV Boot Replace Boot CLICKING NOISE WHILE CORNERING Dry/Worn CV Joints Replace Outer CV Joints CLUNK ON ACCELERATION Dry/Worn CV Joints Replace Inner CV Joints Worn Transmission Gears/Bearings Inspect Transmission VIBRATION/SHUDDER ON ACCELERATION Dry/Worn CV Joints Replace CV Joints Alignment Out Check Alignment Incorrect Spring Height Check Spring Height SQUEALING OR HUMMING Dry/Worn CV Joints Lube/Replace CV Joints Faulty Wheel Bearing Replace Wheel Bearing NOTE: DO NOT allow brake caliper to hang from brake hose. CAUTION: Use care not to damage pinion mate shaft or side gear while driving out axle. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 2
Fig. 2: Removing Left Drive Axle (A/T Vehicles) Courtesy of NISSAN MOTOR CO., U.S.A. Removal (Outer CV Joint) 1. Remove and discard boot bands. Slide boot off joint housing. Thread wheel bearing lock nut onto joint. Using a slide hammer and bearing puller, remove joint from axle shaft. See Fig. 3 . NOTE: Outer joint cannot be disassembled. Remove and inspect joint and replace if damaged or worn. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 3 2. Remove circlip from end of axle, and remove boot. If boot is being reused, take care not to cut boot on axle splines during removal. Clean CV joint in suitable solvent. Inspect components, and replace joint if necessary.

Related Content:

1991 ford ranger manual, shopmanuel for 1991 chevy cavalier, car manual for 1991 lexus ls400, how do i remove cv shaft on 1996 infiniti g20, snap and pop from axel when cornering in silverado, transaxle play in Nissan sentra

Related Content:

where is the blower fuse on a 2001 chevy s10, where is the blower motor resistor located on a 2003 monte carlo, location of mode motor for 99 honda civic lx, 2010 f150heater fan speed issues, 2008 colbalt heater core removal, fuse for rear control panel 2006 durango, Body Control Module 2007 Silverado, 2003 durango sxt hvac blower motor resistor wiring diagram, 2005 silverado ac wiring diagram, 2001 DODGE RAM 2500 OWNERS MANUAL