Skip to content

how to replace door hinges on chevy silverado

You search PDF repair manual about how to replace door hinges on chevy silverado, if there are search results will appear below. If search results do not exist, please search by others keyword.

2005 Chevrolet Chevy K Silverado Disabling Auto Door Locks – keywords dic ipc lock manual mode operation program reprogram Repair Manual

download
Since the 2005 model year, all BCM’s (Body Control Modules) are programmed from the factory to lock all doors when the transmission is shifted into gear or vehicle speed is greater than 8 mph (13 km/h). There is no option to disable the auto door locks from the factory, but if an owner wishes to have the auto door locks disabled the following procedure can be performed: 1. Use the following procedure to disable the auto door locks on the models listed below: 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT 2007-2008 Chevrolet Avalanche, Silverado (new body style), Suburban, Tahoe 2007-2008 GMC Sierra (new body style), Yukon, Yukon Denali, Yukon XL, Yukon Denali XL Reprogram the BCM with updated calibrations currently available in Tis2Web. In some rare instances, the calibrations may not be available in Tis2Web and Techline Customer Support should be contacted to obtain the calibrations. When at the “Calibration Selection” screen in Tis2Web, select “locking” (should be highlighted in Red) and pick the calibration listed as “(Per Customer Request Only) Auto door locks off, option no longer in DIC”.

2004 Chevrolet Chevy K Silverado – 4WD Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

download
Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 2004 Chevrolet Chevy K Silverado – 4WD 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 8 ft box, the CVS line is routed below the frame crossmember. 2. Install the CVS clip to the frame crossmember. 3. Connect the EVAP CVS line to the canister. 4. If the vehicle is equipped with a 6 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 6 ft box, the CVS line is routed above the frame crossmember. 5. Install the CVS clip to the frame crossmember. 6. Connect the EVAP CVS line to the canister. 7. Connect the CVS electrical connector. 8. Install the harness clip to the canister vent solenoid (CVS) line. 9. Lower the vehicle.

2003 Chevrolet Chevy K Silverado Exhaust Popping/Snapping Noise When Vehicle is Hot, at Idle, or Immediately After Vehicle is Shut Off (Replace Muffler Heat Shield) Service Manual

download
Follow the service procedure below to correct this condition. Important: Some popping/snapping noise from the exhaust system during cool down is a normal condition. The customer should be made aware that this service procedure is designed to reduce but not eliminate all exhaust system popping and snapping during cool down. 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. Caution: 2. Remove the nuts securing the muffler to the catalytic converter. 3. On 6.0L and 8.1L equipped vehicles only, loosen the exhaust pipe clamp. Important: Do not use oil base lubricants on the rubber exhaust hangers. 4. Apply a soapy solution to the exhaust pipe hanger rods in order to ease the removal of the exhaust hangers. 5. Pry the exhaust hangers free from the exhaust pipe hanger rods. Important: It is not necessary to remove the muffler from the vehicle to replace the muffler heat shield. 6. Reposition the muffler to gain access to the muffler heat shield 7. Using an air-powered hack saw blade, or equivalent, cut off the existing muffler heat shield just as the heat shield rises off of the muffler. See the illustration above. 8. Remove the heat shield from the muffler. 9. Hammer flush the remaining heat shield to the muffler. Important: 10. Install the new heat shield (see parts list below) onto the muffler as shown above.

1998 – 2003 Toyota Sienna SLIDING DOOR DIAGNOSTIC TIPS/ REPAIR MANUAL

download
CONDITION POSSIBLE CAUSE COMMON REPAIR Top RollerComes Rail bent or widened condition Replace the upper slide door rail. Top Roller Comes Out of Rail Guide The stopper at the end of the rail is loose or missing. Replace the stopper as needed. Door Does Not Lock in Full Open Position Full open stop latch assembly is damaged. Replace the full open stop latch assembly. Left Door Opens Half Way Fuel door half stopper cable damaged. Adjust the cable. Replace the cable, if damaged. Difficltto Open Dirty weatherstrip. Clean all soda spills or other sticky substances that may have accumulated on weatherstrip and door. Difficult to Open Manually Inside handle release button damaged. Replace inside handle release button assembly according to TSB No. BO027-00, “Sliding Door Handle Push Button Operation”. Door out of adjustment. Adjust levelness of the door, according to Repair Manual. Dragging Open/Close Mll Running board rubs against the bottom of the sliding door. Adjust running board to proper position and assure clearance from the door. Manually Roller rails have bent or warp condition. Dirt or debris in the rails and rollers. Clean rails and rollers. Replace damaged parts. CONDITION POSSIBLE CAUSE COMMON REPAIR Creak Noise Junction block, damaged components, and other issues Refer to TSB No. BO003-99, “Sliding Door Creak Noise Reduction.” Refer to the “Common Sources of Creak Noise” section of this bulletin for additional information for sources of creak noise. Rattle or Clicking (NOT Creak Noise) Door moving when driving over bumps Rollers loose or damaged Adjust lower roller base mounting to bring door closer to body (Refer to TIS, applicable model year Sienna Repair Manual, Vehicle Exterior – Door/Hatch – “Slide Door: Adjustment”). Adjust strikers to bring door closer to the body. Inspect the latch assembly and replace, if damaged. Replace damaged rollers. Noise During Open/Close Rollers or rails are damaged and/or dirty. Inspect, clean, and/or replace as needed

2003 HONDA CIVIC Door Panel Removal And Installation Manual

download
2003 CIVIC – Door Panel Removal/Installation Special Tools Required *KTC trim tool set SOJATP2014 *Trim pad remover, Snap-on A 177A or equivalent, commercially available 2-door NOTE: Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. 1. If applicable, remove the regulator handle (A) by pulling the clip (B) out with a wire hook (C). 2. Remove the inner handle (A). Take care not to scratch the door panel. 3. Remove the switch panel (A) (power window model) or the pull pocket (B) (manual window model). -1 Pry out on the upper portion of the cover (B) to release the hooks (C, D), then remove the cover. -2 Remove the screws. -3 Pull the inner handle forward and out half-way to release the hook (E). -4 Disconnect the inner handle rod (F) and power door lock switch connector (G) (driver’s side for some models). – 1 Using a trim tool, pry the cap (C), then remove the screw (D) 4. Remove the screws (H) securing the door panel. 5. Remove the mirror mount cover. 6. Release the clips that hold the door panel (A) with a commercially available trim pad remover (B), then remove the door panel by pulling it upward. Remove the door panel with as little bending as possible to avoid creasing or breaking it. 7. Install the door panel in the reverse order of removal, and note these items: *Replace any damaged clips. *Make sure the connectors are plugged in properly, and the rod is connected properly. *Make sure the window and power door locks operate properly. *If applicable, install the regulator handle so it points forward and up at a 45 º angle with the glass fully closed