how to replace front wheel bearing on a 2004 ford escape

You search PDF repair manual about how to replace front wheel bearing on a 2004 ford escape, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to replace front wheel bearing on a 2004 ford escape Direct Download speed 5432 Kb/s

  how to replace front wheel bearing on a 2004 ford escape Full Version speed 8172 Kb/s



1997 Ford Aerostar/ Ranger Wheel Grease Seal and Bearing Front Replacement and Repacking

0

Filed Under (Ford Manuals) by admin on 20-11-2011

download
Disassembly 1. Raise the vehicle and install Rotunda Car/Truck Stands 077-00018 or equivalent. 2. Remove the wheel and tire assembly. 3. Remove the retainer washers and remove the hub assembly. Refer to Manual Locking or Automatic Locking Hubs under Front Wheel Bearing Adjustment in this section for removal. 4. Remove the disc brake caliper (2B120) as described in Section 06-03 . 5. Remove the hub and rotor. Remove the outer wheel bearing cone. 6. Remove the wheel hub grease seal (1190) from the rotor with Seal Remover TOOL-1175-AC or equivalent and Impact Slide Hammer T50T-100-A. Discard wheel hub grease seal and replace upon assembly. 7. Remove excluder seal. 8. Remove the inner wheel bearing. 9. NOTE: If new wheel bearing cups are installed, install new cone and roller assemblies. Inspect the wheel bearing cups for pits or cracks. If necessary, remove them with Internal Puller D80L-943-A or equivalent and Impact Slide Hammer T50T-100- A. Assembly 1. Lubricate the wheel bearings with High Temperature Constant Velocity Grease E43Z-19590-A or equivalent meeting Ford specification ESP-M1C207-A. Clean all grease from the hub. Pack the cones and rollers. If a bearing packer is not available, work as much lubricant as possible between the rollers and the cages. 2. If wheel bearing cups are to be installed, position wheel bearing cups in rotor and drive in place with Bearing Cup Replacer T80T-4000-P and Driver Handle T80T-4000-W. 3. Position excluder seal on spindle and drive into position using Spindle Seal Replacer T95T-3132-D. 4. Position the inner wheel bearing in the inner wheel bearing cup in the rotor. Install the wheel hub grease seal by driving in place with Seal Replacer T80T-4000-T and Driver Handle T80T-4000-W. 5. Carefully install the rotor onto the front wheel spindle (3105). Refer to Section 06-03 . 6. Install outer wheel bearing into rotor. 7. Refer to Automatic Locking Hubs under Front Wheel Bearing Adjustment in this section for remainder of installation

Related Content:

F550 wheel bearing torque, f53 wheel bearing seal change, wheel bearing 2000 dodge dakota, replacing rear wheel bearing on 2006 escape, Toyota Tacoma Bearing Hub Assembly 2008 inside details, 2009 BUICL ENCLAVE WHEEL BEARING TORQUE, tools needed to change hub and bearing assembly on 2002 tahoe, installing carrier bearing silverado 2002, installing Jedster retaining bearing collar on 9 ford rearend, isuzu npr wheel bearing installation

2004 Chevrolet Silverado 1500 WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) MANUAL

0

Filed Under (Chevrolet Manuals) by admin on 27-06-2012

download
WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) Tools Required J 45859 Axle Remover Removal Procedure 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. 3. Remove the rotor. Refer to Brake Rotor Replacement – Front in Disc Brakes. Fig. 62: View Of Retaining Bolts For Brake Hose And Wheel Speed Sensor Brackets Courtesy of GENERAL MOTORS CORP. 4. Remove the wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle. 2004 Chevrolet Silverado 1500 2004 SUSPENSION Front Suspension – Sierra & Silverado Fig. 63: Removing The Wheel Drive Shaft Nut Retaining Cover (4WD) Courtesy of GENERAL MOTORS CORP. 5. Remove the wheel drive shaft nut retaining cover. IMPORTANT: Do not reuse the nut. A new nut must be used when installing the wheel drive shaft. Fig. 64: Removing Wheel Driveshaft Assembly Retaining Nut And Washer (4WD) Courtesy of GENERAL MOTORS CORP. 6. Remove the wheel driveshaft assembly retaining nut (2) and washer (3) from the wheel driveshaft. 7. Disengage the wheel drive shaft from the wheel hub and bearing using J 45859 or equivalent Fig. 65: Disengaging The Wheel Drive Shaft From The Wheel Hub And Bearing (4WD) Courtesy of GENERAL MOTORS CORP. 8. Remove the wheel hub and the 15-series bearing mounting bolts

Related Content:

wheel bearing 2004 Mountaineer, 2004 CHEVY SILVERADO TCCM, 09 silverado front axle diagram, saturn ion 3 2006 wheel nut torque, torque on 2000 tahoe front brake parts, repair manual for a 95 chevy silverado, torque specs for Tahoe wheel bearing bolt, tourque specs 2003 chev truck 1500 wheels, what size is wheel hub lock nut on 2008 sierra denali, wheel nut torque 2005 f150

2001 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 18-02-2012

download
Wheel Hub Removal All vehicles 1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 . 2. NOTE: Caliper is removed for clarity. Position aside the front disc brake caliper and anchor plate (2B292). 1. Remove the two front disc brake caliper anchor plate bolts. 2. Remove the front disc brake caliper anchor plate and position aside. 3. NOTE: Carry out this step for F-250 and F-350 4×4 SRW vehicles. Remove the rotor. 4. NOTE: Carry out this step for DRW vehicles. NOTE: If excessive force must be used during brake rotor removal, the brake rotors should be checked for lateral runout prior to installation. For additional information, refer to Section 206-00 . Remove the eight hub extender nuts, the hub plate and the rotor. 1. Remove the eight hub plate nuts. 2. Remove the hub plate. 3. Remove the rotor. 5. Remove the hub lock. 1. Remove the retainer ring. 2. Pull outward and remove the hub lock. 6. Remove the axle shaft thrust washers. 1. Remove the snap ring. 2. Remove the three thrust washers. Vehicles equipped with ABS 7. sensor from the bearing. Disconnect the ABS wheel sensor harness. 1. Disconnect the connector. 2. Disconnect the harness routing clips. All vehicles 8. NOTE: The wheel hub and bearing is a slip fit design and should not require a puller to remove it. Remove the wheel hub and bearing. 1. Remove the four lock nuts. 2. Remove the wheel hub and bearing 9. If necessary, remove the brake disc shield. Vehicles with ABS 10. If necessary, remove the bolt and the ABS sensor. All vehicles 11. NOTE: If necessary, position the hub in a soft-jawed vise. Install two nuts on the studs and use the inner nut to remove the studs. 12. Remove and discard the O-ring. Installation All vehicles 1. NOTE: Any time the wheel hub is removed for any reason, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive operations. Install a new O-ring. 2. NOTE: Position the hub in a soft-jawed vise. Install two nuts on the studs and use the outer nut to install the studs. Vehicles equipped with ABS 3. Position the ABS sensor and install the bolt. All vehicles 4. Position the brake disc shield. 5. NOTE: Apply a coat of Ford High Temperature 4×4 Front Axle and Wheel Bearing Grease E8TZ-19590-A meeting Ford specification ESA-M1C198-A to the O-ring area of the wheel hub and bearing before installing the hub and bearing. Install the wheel hub and bearing. 1. Position the wheel hub and bearing. 2. Install the four lock nuts. Vehicle equipped with ABS 6. NOTE: The following step applies only to vehicles equipped with ABS. Connect the ABS sensor harness. 1. Position the ABS sensor harness and install the routing clips. 2. Connect the harness connector. All vehicles 7. n-metallic thrust washer must be installed between the two metal thrust washers. Failure to do so will cause severe wear to the non-metallic thrust washer, allowing the axle shaft to travel further in and out during torque thrust causing damage to the wheel hub and bearing, the axle shaft end seal and the axle shaft. Install the snap ring. 1. Position the three thrust washers onto the axle shaft. 2. Install the snap ring. 8. NOTE: Any time the hub lock is removed, a new O-ring seal must be installed. Failure to do so can cause a vacuum leak and loss of four wheel drive functions. Install a new O-ring. 9. Install the hub lock. 1. Position the hub lock. 2. Install the retainer ring. 10. Position the front disc brake rotor (1125) to the wheel hub (1104). Make sure the wheel hub and the front disc brake rotor braking and mounting surfaces are clean. ? Use brake parts cleaner to clean the front disc brake rotor. 11. NOTE: Carry out this step for DRW vehicles only. Install the front wheel hub extender and nuts.

Related Content:

1995 ford 150 4 wheel drive front hub removal, Need to torque specifications 1999 GMC 1500 wheel hub bearings, snap ring assemble, 2009 impala hub mounting bolt torque, 1998 f250 4x4 front hub bearings torque specs, how to remove a rusted hub assembly, 1977 ford f-350 rear wheel diagram, removing rear axle bearing 2002 toyota tacoma, removing rear wheel bearing race in 06 f-250 super duty lariat, how to change rear hub assembly on a 2006-2010 saturn vue with disk brakes

2004 Buick LeSabre Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Service Manual

0

Filed Under (Buick Manuals) by admin on 04-02-2012

download
Correction 1. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary: 2. Set the tire pressure to 30 psi (205 kPa) COLD. Subject: Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) • Missing balance weights • Bent rim flange • Irregular tire wear • Incomplete bead seating • Tire irregularities • Mud/ice build-up in wheel • Stones in the tire tread © 2009 General Motors Corporation. All rights reserved 3. Road test the vehicle with the Electronic Vibration Analyzer (EVA) essential tool for a sufficient distance on a known, smooth road surface to duplicate the condition. Record the Hertz (Hz) reading as displayed by the EVA onto the tire data worksheet found at the end of this bulletin. This should be done after a tire break-in period of at least 10 miles (16 km) at 45 mph (72 km/h) or greater, in order to eliminate any possible tire flat-spotting. 4. If the road test indicates a shake/vibration still exists, check the imbalance of each tire/wheel assembly on a known, calibrated, off-car dynamic balancer. If any assembly calls for more than ¼ ounce on either rim flange, remove all balance weights and rebalance to as close to zero as possible. Important: Some GM dealers may have a Hunter GSP9700 Road Force Balancer, or a Coats XR1850 Runout Balancer. Either will simplify Step 5 by not requiring dial indicators. If a Hunter GSP9700 machine is available, it may also be used to measure the radial force of the tire/wheel assembly. A guideline here is 18 lbs or less. 5. While on the balancer, measure wheel runout. If radial or lateral runout exceeds .020 in (0.50 mm) for aluminum wheels (.030 in (0.76 mm) for steel wheels), replace the wheel. 6. After confirming wheel balance and wheel runout, if any changes were made, road test the vehicle again. 7. If the smooth road shake/vibration still exists: Important: THE CONTROL ARMS SHOULD ONLY BE INSTALLED ON VEHICLES IF, AFTER THE TIRE AND WHEEL DIAGNOSIS AND REPAIRS HAVE BEEN PERFORMED, THE VIBRATION CONDITION STILL EXISTS. 8. Replace both lower control arms on vehicles built prior to the following VIN breakpoints. On Aurora, Bonneville, DeVille, Park Avenue, Park Avenue Ultra and Seville models, a newly developed hydro-bushing lower control arm with improved damping characteristics has been released. This control arm is not used on the LeSabre. The new lower control arms may provide an incremental improvement to the vehicle ride. Customers who have become “tuned in” to the shake condition may still feel some shake in the vehicle after the new lower control arms are installed. Refer to Lower Control Arm Replacement in SI (refer to the Parts Information table below for SI document ID numbers) . Important: The completed worksheet must be attached to the hard copy of the repair order. • If a Hunter GSP9700 Road Force/Balancing machine is used, record radial force variation (RFV) on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies read more than 18 lbs, match mount the tire to the wheel to get below 18 lbs. Readings of 12 lbs or less are preferable for sensitive customers. • If a Coats XR1850 Runout/Balancing Machine is used, record radial runout of the tire/wheel assemblies on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies are more than .040, match mount the tire to the wheel to get below .040. Readings of .030 inch or less are preferable for sensitive customers. • If the RFV or runout cannot be reduced to an acceptable level, replace the affected tire(s) under the guidelines of the GM Tire Warranty. • The screened tire program is only available for the General branded tires used on the Buick LeSabre. Complete the tire request form at the end of this bulletin and fax to Continental/General. • Road test the vehicle to ensure the shake/vibration has been eliminated

Related Content:

buick terraza hub removal, hunter 9700 user manual, 2005 buick century code p0455, location of fuses and relays 2003 buick park avenue, integrated wheel end FOR F150, hunter lift L401, how to change the lower control arms on a 2005 Titan pdf, how to bypass integrated wheel end 2005 f150, do a 2004 buick lesabre require a rear end alignment, 2000 buick lesabre custom manual

FORD Wheel Bearings REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Ford Manuals) by admin on 16-05-2011

download
Removal & Installation Installation Installation Installation WARNING Do not loosen the axle wheel hub retainer until the wheel and tire are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied. NOTE Have an assistant press the brake pedal to keep the axle from turning. 1. Before servicing the vehicle, please familiarize yourself with safety procedures. 2. Remove the axle”to”wheel hub retainer nut and washer. 3. Remove the parking brake shoes. 4. Press the outboard CV”joint until it is loose from the hub. 5. Remove and discard the toe link”to”wheel knuckle nut. 6. Remove the bolt and separate the toe link from the wheel knuckle. 7. Remove and discard the upper arm”to”wheel knuckle nut. 8. Remove the bolt and separate the upper arm from the wheel knuckle. 9. Remove and discard the lower arm”to”wheel knuckle nut. ? ? WARNING Do not use a hammer to separate the outboard CV”joint from the hub. Damage to the threads and internal CV”joint components can result. ? ? WARNING Do not damage the boot while separating the toe link from the wheel knuckle. ? ? WARNING Do not damage the boot while separating the ball joint from the wheel knuckle. ? ?
To To To To install: install: install: install: 10. Remove the lower arm”to”wheel knuckle bolt. 11. Remove the wheel knuckle. 12. Using a suitable press, remove and discard the wheel hub. 13. Remove and discard the wheel bearing retainer ring. 14. Using a suitable press, remove the wheel bearing

Related Content:

1999 Toyota Prius head torque specifications, 1995 f150 4x4 alignment specfications, what is the wheel torque on a 2013 ford taurus, service manuel cwb-1742 wheel alignment, mazda 3 wheel torque, lug nut torque 2000 Ford E450, How to Read Alignment Specs, how to do a rough tire allignment, 2007 mazda 3 front axle nut torque, 1999 infiniti g20 front axle lug nuts

2004 Toyota Prius EV (Electric Vehicle) Button Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 31-03-2012

download
Time and Difficulty: I found the install to be moderately difficult and pretty time-consuming (about 3 hours) ; others have found it simple and report they have done it in as little as 30 minutes. Your experience will depend on your familiarity with the tools and electronics. I, personally, found insertion of the connection pin into the HV ECU plug to be difficult and almost got the first pin irrevocably stuck in the slot. I spent quite a bit of time with that part alone. I also found threading the wire behind the dash to be fairly tricky. I think the average person, not encountering any problems, could do this job in about 1-1½ hours. Procedure in Brief: 1) Remove bottom cover of steering wheel 2) Locate and unplug flasher plug 3) Open plug and remove 1-3 unused connector pins 4) Reattach steering wheel cover 5) Dismantle part of dash (vents) and remove lower glove box 6) Locate HV ECU (gray plugs) and remove lower plug 7) Solder wire to connector pin and insert into ECU plug (#27) 8) Splice EV button ground wire into ECU plug ground wire (#1) 9) Plug ECU plug back into the ECU 10) Thread wire behind dash to opening near dimmer switch 11) Attach switch to cover and solder wires in place 12) Reassemble the dash 13) Test Procedure in Detail: *Review ALL steps before proceeding and be sure you understand all terms used and you’ve looked at all diagrams and pictures. 1) Remove the bottom cover of the steering wheel by releasing the steering wheel adjustment handle and unscrewing the silver screw in that recess. 2004_prius_evv2.doc Page 4 of 20 Last updated March 13th, 2004 Then, turn the steering wheel 90 degrees right and remove the black screw that becomes visible on the right side of the steering column. Then turn the wheel 180 degrees left (90 degrees from normal position) and remove the black screw on the left side of the steering column. Carefully pull down on the lower portion of the steering column cover until it releases. Mine was a bit stiff/stuck to the upper part and you may need to carefully use a butter knife or screwdriver to start prying them apart. 2004_prius_evv2.doc Page 5 of 20 Last updated March 13th, 2004 2) Locate and unplug the white flasher plug visible just on the left side of the bottom of the steering column. 3) 2 little clips keep a cover locked in place. Pull those apart and remove the cover. Inside you’ll see lines of silver connector pins–some with wires attached, some without. You should remove between 1 and 3 of those pins–2 is probably safe, 3 might be better, since if you plan to install an OEM button at some point, you’ll probably need more pins for that. (You need one pin for the procedure, but it’s handy to have a back-up.) To remove the pins, you can use your paper clip to start the process of sliding them out, and then they just pull right out. 2004_prius_evv2.doc Page 6 of 20 Last updated March 13th, 2004 Stick them to a piece of tape or put them somewhere secure so you can find them later. Snap the cover back into place, and plug the flasher plug back in. 4) Replace the steering wheel cover by reversing the process. Be sure everything’s aligned properly and that there are no gaps. 5) Now you’ll need to dismantle part of the dash to get access to the ECU and other areas. First, open the top and bottom glove box doors. Squeeze the inside sides of the lower glove box together to get the catches past the portion of the dash frame that keeps the door from falling all the way open. Then pull the entire door straight toward you – it will unclip from the hinges at the bottom of the glove box. 2004_prius_evv2.doc Page 7 of 20 Last updated March 13th, 2004 You may also need to unclip the little hydraulic piston that keeps the door from falling open too quickly. Next, grasp the bottom of the silver vent piece next to the glove box. Pull it toward you firmly. It should unclip at the bottom first. Then pull the whole unit straight out

Related Content:

2004 Sienna Fuse Box Diagram, 2004 Chevrolet Malibu Classic Manual Free, 2004 suburban sunroof problems, 2004 honda crv repair manual pdf, all air vents open on 2004 ford explorer, exploded view pontiac grand prix ac system, exhaust system for 2004 malibu maxx lt, 2004 sienna thermostat replacement, 2004 mazda 3 headlight adjustment, how to reset computer on 2004 chevy impala

2000 BMW 528i (E39) DOHC Front Wheel Bearing Removal And Installation Manual

0

Filed Under (Bmw Manuals) by admin on 28-04-2012

download
Replacing Front Wheel Bearing ( Wheel Hub )(Basis) Caution! Bearing cannot be dismantled. Do not wash out bearings. Remove brake disk (brake line remains connected), refer to Brakes and Traction Control; Disc Brake System. Remove ABS impulse sensor. Remove stabilizer link from stabilizer, Steering and Suspension. Unfasten nut. Installation: Use washer (1). Tapered spigot and bore both free of grease. Replace self-locking nut. Brace on hexagon socket if necessary. Tightening Torque, refer to Steering Specifications. Press off track rod with special tool 31 2 240. Mark the installation position of the spring strut tube (1) in the swivel bearing (2) with paint – never mark with scribing tool. Marking is not required if the factory mark is still identifiable. R installation position of right spring strut tube L installation position of left spring strut tube Version with factory marking above the swivel bearing. Unfasten nut. Expand swivel bearing with special tool 31 2 200 and pull swivel bearing downwards. Installation: Press swivel bearing upwards to stop with workshop hoist and note marking of installation position. Replace self-locking nut. Tightening Torque, refer to Suspension Specifications Unfasten screws and remove wheel bearing. Installation: Contact face (2) of wheel bearing and swivel bearing and the threaded bores (1) must be clean and free of grease. Tightening Torque, refer to Suspension Specifications

Related Content:

2000 528i bmw manual, 2000 bmw 528i radio manual, 2000 bmw 528i wheel bearing hub

1997 Jeep Grand Cherokee Laredo 7 1/8″, 7 1/3″, 7 9/16″, 7 4/5″, 8 1/4″, 8 1/2″ & 8 9/10″ Ring Gears Removal And Installation Manual

0

Filed Under (Jeep Manuals) by admin on 04-07-2012

download
Removal (Model 194, 8 1/4″ & 1998 Grand Cherokee 216 Axles) 1. Raise and support vehicle. Remove rear wheel(s). If equipped with drum brakes, remove brake drum. If equipped with disc brakes, remove brake caliper and rotor. On all models, clean axle housing cover. Loosen cover bolts, and drain oil. Remove cover. 2. Remove differential pinion-shaft lock bolt. Remove pinion shaft from differential. Push in axle. Remove “C” clip from axle at pinion gear. Remove axle from tube. Remove axle shaft seal and bearing from axle tube. Installation 1. Grease bearing, and install into axle tube. Ensure bearing part number is facing outwards. Apply wheel bearing grease to axle shaft seal. Install seal in axle tube. Install axle shaft. 2. Install axle “C” clip. Pull axle out to seat “C” clip. Install pinion shaft. Install lock bolt, and tighten to specification. Apply RTV to axle housing cover. Tighten cover bolts to specification. See TORQUE SPECIFICATIONS table. Fill with gear oil. Removal (Model 198, 1999 Grand Cherokee 216 & 226 Axles) 1. Raise and support vehicle. Remove rear wheel(s). Remove brake drum. Remove nuts securing axle retainer plate to axle tube, and discard. Using slide hammer and Adapter (6790), remove axle shaft from axle tube. 2. Using a 3/8″ drill bit, drill a shallow hole into bearing retaining ring on axle. DO NOT drill into axle. Using a cold chisel, cut bearing retaining ring across drilled hole, and remove from axle shaft. Using a press and Bearing Remover (1130), remove bearing from axle shaft. Remove seal and retainer plate from axle shaft. Installation 1. Ensure axle shaft retaining plate is flat and not warped. Install retaining plate on axle shaft. Apply wheel bearing grease to axle shaft seal. Install seal on axle shaft. Grease bearing, and install on axle shaft with outer surface groove facing seal. 2. Using press and Bearing Installer (7913), press bearing onto axle shaft. Press NEW bearing retainer ring onto axle shaft. Install axle shaft in axle tube. Tighten NEW axle retainer plate nuts to specification. See TORQUE SPECIFICATIONS table. PINION SEAL & YOKE Removal

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, exploded view 1996 jeep grand cherokee exploded view of front suspension, Meritor Axle Nut Torque Specs, Silverado Rear Axle Seal Replacement, how to remove right front axle 95 bronco, saturn sl hub bolt torque, DIY LEXUS GX 470 AXLE REPLACE, how to remove axle seal in a 1999 chevy malibu, size axle nut 2005 explorer, 2002 ford expedition trailing arm torque specs

1991 Infiniti G20 AXLE SHAFTS – FRONT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Infiniti Manuals) by admin on 13-02-2012

download
REMOVAL & INSTALLATION FWD AXLE SHAFT Removal (Axle Shaft) 1. Raise and support vehicle. Remove front wheel assembly. Remove wheel bearing lock nut. Remove brake caliper, and support aside. Remove brake rotor. 2. Disconnect tie rod end. Remove upper knuckle nut, and separate knuckle assembly from third link assembly. Push axle shaft through hub, and separate axle assembly from knuckle assembly. 3. Insert screwdriver blade between transaxle case and right axle inner CV joint. Pry out on joint until joint pops free. Use care not to damage axle boot or axle seal. 4. On M/T vehicles, remove left axle in same manner. On A/T vehicles, insert screwdriver through differential, and drive axle out of transaxle case using a hammer. See Fig. 2 . PROBLEM Possible Cause/Action GREASE LEAKING Ripped CV Boot Replace Boot CLICKING NOISE WHILE CORNERING Dry/Worn CV Joints Replace Outer CV Joints CLUNK ON ACCELERATION Dry/Worn CV Joints Replace Inner CV Joints Worn Transmission Gears/Bearings Inspect Transmission VIBRATION/SHUDDER ON ACCELERATION Dry/Worn CV Joints Replace CV Joints Alignment Out Check Alignment Incorrect Spring Height Check Spring Height SQUEALING OR HUMMING Dry/Worn CV Joints Lube/Replace CV Joints Faulty Wheel Bearing Replace Wheel Bearing NOTE: DO NOT allow brake caliper to hang from brake hose. CAUTION: Use care not to damage pinion mate shaft or side gear while driving out axle. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 2
Fig. 2: Removing Left Drive Axle (A/T Vehicles) Courtesy of NISSAN MOTOR CO., U.S.A. Removal (Outer CV Joint) 1. Remove and discard boot bands. Slide boot off joint housing. Thread wheel bearing lock nut onto joint. Using a slide hammer and bearing puller, remove joint from axle shaft. See Fig. 3 . NOTE: Outer joint cannot be disassembled. Remove and inspect joint and replace if damaged or worn. 1991 Infiniti G20 AXLE SHAFTS – FRONT’ ’1991-92 DRIVE AXLES FWD Axle Shafts None Page 3 2. Remove circlip from end of axle, and remove boot. If boot is being reused, take care not to cut boot on axle splines during removal. Clean CV joint in suitable solvent. Inspect components, and replace joint if necessary.

Related Content:

1991 ford ranger manual, shopmanuel for 1991 chevy cavalier, car manual for 1991 lexus ls400, how do i remove cv shaft on 1996 infiniti g20, snap and pop from axel when cornering in silverado, transaxle play in Nissan sentra

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, 2005 explorer transmission exploded view, 2003 trailblazer torque converter removal, gm 4l60e band adjustment screws, automatic transmission adjustments for 1997 yuko, 2011 crv engine whine, how to check tranmission fluid on 2012 kia sedona, e4od repair manual download, how to adjust the bands of an automatic trasmission of hyundai accent 2002, 2004 saturn Clutch Assembly Exploded View

Related Content:

F550 wheel bearing torque, f53 wheel bearing seal change, wheel bearing 2000 dodge dakota, replacing rear wheel bearing on 2006 escape, Toyota Tacoma Bearing Hub Assembly 2008 inside details, 2009 BUICL ENCLAVE WHEEL BEARING TORQUE, tools needed to change hub and bearing assembly on 2002 tahoe, installing carrier bearing silverado 2002, installing Jedster retaining bearing collar on 9 ford rearend, isuzu npr wheel bearing installation