replace idler pulley belt tensioner chrysler

You search PDF repair manual about replace idler pulley belt tensioner chrysler, if there are search results will appear below. If search results do not exist, please search by others keyword.



  replace idler pulley belt tensioner chrysler Direct Download speed 5432 Kb/s

  replace idler pulley belt tensioner chrysler Full Version speed 8172 Kb/s



2002 Mitsubishi Montero Limited Removing Drive Belt Auto Tensioner/ Aligning Timing Marks

0

Filed Under (Mitsubishi Manuals) by admin on 14-01-2012

download
Aligning Timing Marks (2001-02 Montero) Courtesy of MITSUBISHI MOTOR SALES OF AMERICA. Installation (2001-02 Montero) 1. Place auto-tensioner in soft-jawed vise to SLOWLY compress the push rod. If there is a plug at the base of the auto-tensioner body, place flat washer around plug so it will not contact vise jaw. 2. Slowly compress auto-tensioner push rod until holes in push rod and auto-tensioner housing are aligned. Insert a locking pin into the alignment holes. Install auto-tensioner on engine. 3. Ensure all timing marks are still aligned. See Fig. 11 . Install timing belt on crankshaft sprocket, idler pulley, left bank camshaft sprocket, water pump pulley, right bank camshaft sprocket, and tensioner CAUTION: Never compress the auto-tensioner too fast, or the push rod will be damaged. WARNING: Right bank camshaft can easily turn from applied spring pressure. Be careful not to pinch fingers when installing timing belt. 2002 Mitsubishi Montero Limited MITSUBISHI 3.5L V6 – SOHC many waters gallery pulley. Take all slack out of timing belt. 4. Loosen the tensioner pulley center bolt. Using Tensioner Pulley Wrench (MD998767), rotate tensioner pulley against timing belt. Temporarily tighten tensioner pulley center bolt. Using Crankshaft Pulley Spacer (MD998769), turn crankshaft 1/4 turn counterclockwise. Turn crankshaft 1/4 turn clockwise. Ensure all timing belt marks are still aligned. 5. Loosen tensioner pulley center bolt. Position tensioner pin holes at bottom of tensioner. Install Tensioner Pulley Wrench (MD998767) on tensioner pulley. See Fig. 12 . Using torque wrench, apply 39 INCH lbs. (4.4 N.m) of torque (counterclockwise direction) to tensioner pulley. Tighten tensioner center bolt to specification while holding tensioner pulley stationary. See TORQUE SPECIFICATIONS . 6. Remove locking pin from auto-tensioner. Turn crankshaft 2 revolutions clockwise and align all timing marks. DO NOT rotate counterclockwise. 7. Wait for at least 5 minutes, then check auto-tensioner push rod protrusion. To check push rod protrusion, measure clearance between body of auto-tensioner and bottom of tensioner pulley bracket arm. Clearance should be 0.15-0.20″ (3.8-5.0 mm). If protrusion is not correct, repeat timing belt tensioning procedure. Ensure all timing marks are aligned. 8. Install timing belt covers. See Fig. 10 . Install crankshaft pulley. Tighten crankshaft pulley bolt to specification. See TORQUE SPECIFICATIONS . Install accessory mount assembly on front of engine. See Fig. 13 . See TORQUE SPECIFICATIONS . To install remaining components, reverse removal procedures. See Fig. 7 and Fig. 8 . Adjust drive belts to proper tension. 9. When filling cooling system, use 50/50 mix of coolant and water. Open bleed screw on top of thermostat housing. Slowly fill cooling system until coolant flows out of bleed hole. Install bleed screw. Start engine and run to normal operating temperature. Race engine to 3000 RPM several times. Stop engine. After engine cools, refill radiator and coolant reservoir tank.

Related Content:

the torque specs on a 2001 Mitsubishi Montero limited thermostat housing, 02 mitsubishi montero limited repair manual, montero crank shaft pully removal, 2003 buick 3 8 turbo engine tensioner pulley replacement youtube, MITSUBISHI CANTER 4M51 MANUAL, manuals for mitsubishi montero limited 2002, isuzu 4hk1-tc specs flywheel tension, HAW TO CHAIN SEOL VALVE THE MITSUBISHI MONTERO 3 0L 2002, free repair manual mitsubishi montero, dodge neon timing belt tensioner setting

Peugeot 306 Timing belt replacement Removal And Installation Manual

0

Filed Under (Peugeot Manuals) by admin on 23-02-2011

download
Removal Removal Raise and support front of vehicle. 1. Remove: RH front wheel. Engine undershield (if fitted). Lower inner wing panel. Auxiliary drive belt(s). 307: Engine tie-bars. Crankshaft pulley [1] . Timing belt upper cover [2] . Timing belt centre cover [3] . Timing belt lower cover [4] . 2. Turn crankshaft to setting position. Insert timing pins in camshaft sprocket and flywheel [5] & [6] . 3. Slacken tensioner nut to release tension on belt [7] . Lightly tighten nut. 4. Remove timing belt. 5. Installation – -1997 Installation – -1997 Ensure timing pins located correctly [5] & [6] . 1. Fit timing belt in following order: Crankshaft sprocket. Camshaft sprocket. Water pump sprocket. 2. Manufacturer: Peugeot Model: 306 (93-97) 1,4 Engine code: TU3M/Z (KDZ) Output: 55 (75) 5800 Tuned for: R-Cat Year: 1993-97 – Tensioner pulley. NOTE: Ensure belt is taut between sprockets on non-tensioned side. Slacken tensioner nut [7] . Turn tensioner anti-clockwise to tension belt. Temporarily tighten nut. 3. Remove timing pins [5] & [6] . 4. Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. 5. Slacken tensioner nut [7] . 6. Tension belt as follows: 7. Turn tensioner anti-clockwise until tension gauge indicates 45 SEEM units. 8. Tighten tensioner nut to 20 Nm [7] . 9. Remove tension gauge. 10. Turn crankshaft four turns clockwise to setting position. 11. Ensure timing pins can be inserted [5] & [6] . 12. Wait 1 minute to allow belt to settle. 13. Apply firm thumb pressure to belt at . 14. Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. 15. Slacken tensioner nut [7] . 16. Turn tensioner anti-clockwise to tension belt. New belt: 40 SEEM units. Used belt: 36 SEEM units. 17. Tighten tensioner nut to 20 Nm [7] . 18. Remove tension gauge [8] . 19. Turn crankshaft two turns clockwise. 20. Ensure flywheel timing pin can be inserted [6] . NOTE: DO NOT allow crankshaft to turn anti-clockwise. 21. Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. 22. Check tension gauge reading. New belt: 51±3 SEEM units. Used belt: 45±3 SEEM units. 23. Install components in reverse order of removal. 24. Tighten crankshaft pulley bolts to 8 Nm [9] . 25. Installation – 1997- Installation – 1997- Ensure timing pins located correctly [5] & [6] . 1. Fit timing belt in following order: Crankshaft sprocket. Camshaft sprocket. Water pump sprocket. Tensioner pulley. NOTE: Ensure belt is taut between sprockets on non-tensioned side. 2. Slacken tensioner nut [7] . Turn tensioner anti-clockwise to tension belt. Temporarily tighten nut. 3. Remove timing pins [5] & [6] . 4. Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. 5. Slacken tensioner nut [7] . 6. Tension belt as follows: 7. Remove cylinder head cover. 8. Install valve spring compressor. Tool No.0132AE [10] . 9. Turn tensioner anti-clockwise until tension gauge indicates the following: Except 307: 31 SEEM units. 307: 44 SEEM units.

Related Content:

videos on removal of tensioner pulley on 2005 dodge neon, HUB A433T4232, remove right timing belt cover 2004 axiom, volvo penta 5 belt tighten, MERITOR HUB A433T4232, peugeot 307 camshaft repair, picture belt assembly on 98 4 3 volvo penta, peugeot pdf belt, peugeot 107 alternator belt diagram, noise of timing belt broken tensioner bearing 1991 toyota corolla

Honda Civic A/C Compressor Belt Adjustment

0

Filed Under (Honda Manuals) by admin on 21-11-2011

download
1. Apply a force of 98 N (10 kgf, 22 Ibf), and measure the deflection between the A/C compressor and the crankshaft pulley. A/C Compressor Belt Used Belt: B16A2 engine 6.0 – 9.5 mm (0.24 – 0.37 in) 7.5 – 9.5 mm (0.30 – 0.37 in) 4.5 – 6.5 mm (0.18 – 0.26 in) 5.0 – 6.5 mm (0.20 – 0.26 in) Except B16A2 engine New Belt: B16A2 engine Except B16A2 engine Note these items when adjusting belt tension: If there are cracks or any damage evident on the belt, replace it with a new one. ” Used belt ” means a belt which has been used for five minutes or more. ” New belt ” means a belt which has been used for less than five minutes. 2. Loosen, the center nut of the idler pulley (SANDEN), or the pivot bolt of the idler pulley bracket and the lock nut of the adjusting bolt (DENSO). Turn the adjusting bolt to get proper belt tension. Retighten the center nut of the idler pulley (SANDEN), or the pivot bolt of the idler pulley bracket and the lock nut of the adjusting bolt (DENSO). Recheck the deflection of the A/C compressor belt. 3. 4. 5. Tension Gauge Method 1. Attach the special tool to the 4/C compressor belt as shown below, and measure the tension of the belt. A/C Compressor Belt Used Belt: B16A2 engine 390 – 540 N (40 – 55 kgf, 88 – 120 Ibf) Except B16A2 engine 340 – 490 N 135 – 50 kgf, 77 – 110 Ibf) New Belt: B16A2 engine 740 – 880 N (75 – 90 kgf, 170 – 200 Ibf) Except B16A2 engine 690 – 830 N (70 – 85 kgf, 150 – 190 Ibf) Note these items when adjusting belt tension: Follow the manufacturer’s instructions for the belt tension gauge. If there are cracks or any damage evident on the belt, replace it with a new one. ” Used belt ” means a belt which has been used for five minutes or more. ” New belt ” means a belt which has been used for less than five minutes. 2. Loosen the center nut of the idler pulley (SANDEN), or the pivot bolt of the idler pulley bracket and the lock nut of the adjusting bolt (DENSO). Turn the adjusting bolt to get proper belt tension. Retighten the center nut of the idler pulley (SANDEN), or the pivot bolt of the idler pulley bracket and the lock nut of the adjusting bolt (DENSO). Recheck the tension of the 4/C compressor belt

Related Content:

2003 kia sedona belt tensioner lock nut, drive belt routing diagrams 2012 kia optima, why does ac compressor lock up on 98 honda civic

Toyota LandCruiser 4.2TD Timing belt replacement intervals

0

Filed Under (Toyota Manuals) by admin on 02-03-2012

download
Timing belt replacement intervals The information relating to timing belt replacement intervals is additional to the main purpose of this CD, but is included to provide guidance to garages and for customer advice. Where possible the recommended intervals have been compiled from vehicle manufacturers’ information. In a few instances no recommendation has been made by the manufacturer and the decision to replace the belt must be made from the evidence of a thorough examination of the condition of the existing belt. Apart from the visible condition of the belt, which is explained fully later in this section, there are several other factors which must be considered when checking a timing belt: Is the belt an original or a replacement. 1. When was the belt last replaced and was it at the correct mileage. 2. Is the service history of the vehicle known. 3. Has the vehicle been operated under arduous conditions which might warrant a shorter replacement interval. 4. Is the general condition of other components in the camshaft drive, such as the tensioner, pulleys, and other ancillary components driven by the timing belt, typically the water pump, sound enough to ensure that the life of the replacement belt will not be affected. 5. If the condition of the existing belt appears good, can you be satisfied that the belt will not fail before the next check or service is due. 6. If the belt does fail, have you considered the consequences. If the engine is an INTERFERENCE type then considerable expensive damage may well be the result. 7. The cost of replacing a belt as part of a routine service could be as little as 5 to 10% of the repair cost following a belt failure. Make sure your customer is aware of the consequences. 8. If in doubt about the condition of the belt – RENEW it. 9. Removal Removal Remove timing belt cover [1]. 1. Turn crankshaft clockwise until timing marks aligned [2]. 2. Ensure timing marks aligned: 1KZ-T/TE: [3]. 3. 4. Remove: Automatic tensioner unit [6]. Tensioner pulley bolt [7]. Tensioner pulley [8]. Timing belt. 5. Installation Installation Check tensioner pulley for smooth operation [8]. Replace if necessary. 1. Remove dust cover. Check tensioner body for leakage or damage [6]. Check pushrod protrusion is 9,0-9,8 mm [9]. 2. Check pushrod does not move when pushed against a firm surface. If pushrod moves: Replace automatic tensioner unit. 3. Slowly compress pushrod into tensioner body until holes aligned. Use press. 4. Retain pushrod with 1,5 mm Allen key through hole in tensioner body [10]. Fit dust cover. 5. Ensure timing marks aligned [2]. 6. Ensure timing marks aligned: 1KZ-T/TE: [3]. 1HD-FT/1HD-FTE: [4]. 7. Fit timing belt in anti-clockwise direction, starting at lower sprocket. Ensure belt is taut between sprockets. 8. Fit tensioner pulley [8]. Tighten bolt to 34 Nm [7]. 9. Push tensioner pulley against belt. Install automatic tensioner unit [6]. Tighten bolts evenly to 13 Nm [5]. 10. Remove Allen key from tensioner body to release pushrod. 11. Turn crankshaft two turns clockwise. Ensure timing marks aligned [2] & [3] or [4]. 12. If not: Repeat installation and tensioning procedures. 13. Install components in reverse order of removal. 14. Reset timing belt replacement warning lamp as follows: 15. -Runner/Landcruiser: Remove grommet in speedometer housing. Depress switch using a thin screwdriver [11]. 16. Colorado: Remove speedometer housing. Remove screw indicated and insert in alternative location [12]. 17. Amazon: Lamp illuminates at 90,000 miles. Return vehicle to dealer.

Related Content:

mazda bt50 timing belt replacement, 4 7L Toyota Timing Belt Replacement, Kia 3 5 Timing Belt Replacement, honda odyssey timing belt replacement mileage, 2004 subaru forester XT timing you tube instalation, Timing Belt Replacement Intervals Pontiac, how often change timing belt 2011 chevy malibu, how to change a timing belt on a 2011 kia soul, how to install varable timing solenoid on gmc envoy xuv 4 2l, how to remove a three bolt crankshaft pulley mazda bt 50

2004 Kia Sorento EX TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Kia Motors Manuals) by admin on 03-06-2012

download
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove engine cover. Using 16-mm spanner wrench, rotate serpentine belt tension arm clockwise about 14 degrees to relieve belt tension. Remove serpentine drive belt. Remove power steering pump pulley, idler pulley, tensioner pulley and crankshaft pulley. Remove upper and lower timing belt covers. See Fig. 1 or Fig. 2 . 2. Ensure timing marks of camshaft sprocket and cylinder head cover are matching. See Fig. 5 . On Sedona, support engine with jack and remove engine mounting insulator. On all models, remove auto tensioner. See Fig. 3 . 3. Unbolt timing belt tensioner pulley, and remove timing belt. CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: Rotate crankshaft clockwise and align timing mark to set No. 1 cylinder to TDC on compression stroke. NOTE: If timing belt is to be reused, mark rotational direction on belt for reinstallation reference. CAUTION: If either camshaft is set at TDC for cylinder No. 1 at the compression stroke and the corresponding camshaft on the same cylinder head is rotated 180 degrees while the timing belt is removed, intake and exhaust valves may contact each other Inspection Inspect timing belt for wear on edges of drive teeth. Inspect the belt for signs of oil contamination, cracks, separation, worn or missing teeth, or hardened Black surface. Replace belt if worn, damaged or contaminated. Inspect belt tensioner pulley for smooth rotation. Replace if defective. Check timing belt auto tensioner for leaks. Replace if necessary. Installation 1. Install timing belt idler pulley to engine support lower bracket. Install tensioner arm, shaft and washer to cylinder block. Tighten tensioner arm bolt to specification. See TORQUE SPECIFICATIONS . 2. Install crankshaft sprocket and align timing mark. See Fig. 4 . Install camshaft sprocket and adjust installation positions as shown. See Fig. 5 and Fig. 6 . Install auto tensioner to oil pump case. Ensure that

Related Content:

change timing belt 2004 kia sorento, 2003 kia sorento power steering pump replacement, 2004 sorento replace drive belts, how to install a motor mount on a kia sedona, how to replace the camshaft pulley bolt on a 2004 Kia Sorento here at home?, how to take a intake manifold off of a 2003 kia sorento, how to time a 2004 kia sorento, kia sedona steering pump rebuilt, kia sorento drive shaft repair

1991 Subaru Loyale Sedan (4 Door) Camshaft And Timing Belt Repair Manual

0

Filed Under (Subaru Manuals) by admin on 27-06-2012

download
Tightening torque: REMOVAL 1. Loosen water pump pulley mounting nuts or bolts. 2. Loosen two alternator mounting bolts, and detach V-belt. [Except air conditioner equipped model] 3. Remove water pump pulley and pulley cover. 4. Disconnect lead from oil pressure switch. 5. Remove oil level gauge guide together with gauge. 6. Remove crankshaft pulley. To lock crankshaft, use FLYWHEEL STOPPER [manual transmission model] or DRIVE PLATE STOPPER [automatic transmission model]. 7. Remove belt cover plate. [TURBO model] 8. Remove belt covers LH, RH and FR. 9. Removing timing belt Zoom Sized for Print (a) Loosen tensioner mounting bolts on # 1 cylinder by 1/2 turn. (b) With tensioner fully turned to slacken belt, tighten mounting bolts. (c) Mark rotating direction of timing belt, then remove belt. (d) Loosen tensioner No. 2 mounting bolts on # 2 cylinder by 1/2 turn. (e) With tensioner fully rotated to slacken belt by using TENSIONER WRENCH, tighten tensioner mounting bolts. NOTE: Cover TENSIONER WRENCH clamping tips with a rubber hose or waste cloth to prevent crankshaft or pulley from being damaged 10. Remove tensioner and tensioner No. 2 together with tensioner spring. 11. Remove belt idler. 12. Remove camshaft sprockets by using CAMSHAFT SPROCKET WRENCH. 13. Remove right-hand belt cover No. 2, left-hand belt cover No. 2 and belt cover RR. TIMING BELT 1. Check timing belt teeth for breaks, cracks, and wear. If any fault is found, replace belt. 2. Check the condition of back side of belt; if any crack is found, replace belt. A. Be careful not to let oil, grease or coolant contact the belt. Remove quickly and thoroughly if this happens. Zoom Sized for Print

Related Content:

subaru timing cover bolts, wire diagrams for a 91 subaru loyale

2002 HONDA ACCORD – Timing Belt and Balancer Belt Installation Instructions

0

Filed Under (Honda Manuals) by admin on 22-01-2011

download
1. Remove and clean the balancer belt drive pulley. 2. Clean the timing belt pulleys, and the upper and lower timing cover. 3. Set the crankshaft to TDC. Align the dimple (A) on the tooth of the timing belt drive pulley with the pointer (B) on the oil pump. 4. Clean the camshaft pulley and set it to TDC. 5. Install the timing belt in a counterclockwise sequence, starting with the drive pulley. -1 The ”UP” mark (A) on the camshaft pulley should be at the top. -2 Align the TDC grooves (B) on the pulley with the top edge of the head. -1 Drive pulley (A). -2 Tensioner pulley (B). -3 Water pump pulley (C). -4 Camshaft pulley (D). 6. Loosen and retighten the adjusting nut to tension the timing belt. 7. Clean any oil off both faces of the balancer belt drive pulley. 8. Check the lower cover rubber seal for cracks and other damage. NOTE: ?If the rubber seal is coming off, apply liquid gasket to the lower cover and reinstall the rubber seal. Wipe off any liquid gasket that is pressed out. ?When replacing the rubber seal, clean the lower cover groove, cut the repair rubber seal to length, and put the rubber seal into the groove evenly. 9. Install the balancer belt drive pulley and the lower cover. 10. Temporarly install the crankshaft pulley and bolt. 11. Rotate the crankshaft pulley five or six turns counterclockwise to seat the timing belt on the pulleys. 14. Check the camshaft pulley marks. ?If the camshaft pulley marks are also at TDC, go to step 15. ?If the camshaft pulley marks are not at TDC, remove the timing belt and repeat steps 3, 4 and 5. 15. Remove the crankshaft pulley and the lower cover. 16. Turn the crankshaft to TDC again. 17. Lock the timing belt adjuster arm in place with one of the 6 mm timing cover bolts. 18. Loosen the adjusting nut 2/3-1 turn, and make sure the balancer belt tensioner moves freely. Then push the tensioner up and retighten the adjusting nut. 19. Align the rear balancer shaft pulley with a 6 x 100 mm bolt (or equivalent). -1 Remove the bolt (A) and washer (B) from the maintenance hole (C). -2 Scribe a line on a 6 x 100 mm bolt, 74 mm (2.9 in) from the end

Related Content:

2002 honda accord 2 3 timing belt tension adjustment, toyota2y engine only starts when rocker shaft has been loosened, 2005 audi 3 2 tdc diagram, 2006 kia sorento camshaft pulley repair manual pdf, how to replace a tensioner pulley on a 2006 mazda 5, 2003 buick lasabre serpentine belt idler pulley torque spec, mazda 6 crankshaft tool, pulley configuration 2001 buick lesabre, Residue from serpentine bolt on smooth pulleys, lincoln ls crank pulley diagram

2002 Dodge Neon Power Steering Belt Service and Repair Manual

0

Filed Under (Dodge Manuals) by admin on 15-04-2012

download
Power Steering Belt REMOVAL POWER STEERING PUMP AND AIR CONDITIONING COMPRESSOR BELT 1. Using a 17 mm wrench, rotate belt tensioner clockwise (Fig. 2) until belt can be removed from power steering pump pulley. Gently, release spring tension on tensioner. 2. Remove the drive belt (Fig. 3). Clean all foreign debris from belt pulley grooves. The belt pulleys must be free of oil, grease, and coolants before installing the drive belt. INSPECTION Belt replacement under any or all of the following conditions is required: ^Excessive wear ^Frayed cords ^Severe glazing Poly-V Belt system may develop minor cracks across the ribbed side (due to reverse bending). These minor cracks are considered normal and acceptable. Parallel cracks are not (Fig. 6). NOTE: Do not use any type of belt dressing or restorer on Poly-V Belts. INSTALLATION NOTE: When installing drive belt on the pulleys, make sure that belt is properly routed and all V-grooves make proper contact with pulley grooves. POWER STEERING PUMP AND AIR CONDITIONING COMPRESSOR BELT 1. Install the drive belt (Fig. 3) over all the pulleys except for the power steering pump pulley 2. Using a 17 mm wrench, rotate belt tensioner clockwise (Fig. 2) until belt can be installed on the power steering pulley Release spring tension onto belt. 2002 Dodge Neon L4-2.0L VIN C Copyright © 2009, ALLDATA 9.90 Page 4 3. After belt is installed, inspect belt length indicator marks (Fig. 7). The indicator mark should be within the minimum belt length and maximum belt length marks. On a new belt, the indicator mark should align approximately with the nominal belt length mark

Related Content:

2002 dodge intrepid steering short circuit, 2002 dodge nein manual, 2002 dodge neon repair, 2003 dodge neon belt diagram, Dodge Intrepid repair Manual PDF, Free Download Air Compressor Manual

1995 Isuzu Trooper LS TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Isuzu Manuals) by admin on 13-05-2012

download
TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2. Remove fan pulley assembly. Remove crankshaft pulley bolt. Using Puller (J-8614-01) or equivalent, remove crankshaft pulley. Remove oil cooler hose from timing cover. Remove timing belt cover. Align all timing marks prior to belt removal. See Fig. 1 – Fig. 4 . Remove belt tensioner pusher and timing belt. Fig. 1: Aligning Timing Belt Sprockets (DOHC) Courtesy of ISUZU MOTOR CO. Installation 1. Ensure all timing marks are aligned. Install belt over one pulley at a time starting at crankshaft sprocket and working counterclockwise. Belt should go over tensioner last. Secure belt at each pulley during installation with pinch clips. See Fig. 5 . 2. Compress timing belt tensioner pusher and insert pin to retain pusher. Apply pressure to tensioner against belt, and install tensioner pusher. Tighten bolts to specification. See TORQUE SPECIFICATIONS . 3. Loosen tensioner pulley bolt. Apply pressure on belt by rotating tensioner. Tighten tensioner pulley bolt to specification.. See TORQUE SPECIFICATIONS . Remove pin from timing belt tensioner pusher. 4. Remove pinch clips from timing belt (if used). Install crankshaft pulley, tightening center bolt finger tight. Rotate crankshaft 2 turns clockwise. Ensure timing belt tensioner pusher rod protrudes proper

Related Content:

2004 Isuzu NPR refrigerant, isuzu 4hk1 timing marks

1996 Mitsubishi Eclipse GS-T TIMING BELT And BALANCE SHAFT BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Mitsubishi Manuals) by admin on 29-04-2012

download
Removal 1. Disconnect negative battery cable. Remove engine undercover. Place wooden block between jack and oil pan, and raise engine slightly. Remove engine mount assembly near timing belt cover. 2. Remove clamp for power steering return hose near timing belt cover. Remove all drive belts and tensioner pulley bracket. See Fig. 1 . Remove power steering and water pump pulleys. Rotate crankshaft clockwise so that No. 1 cylinder is at TDC of compression stroke. Remove crankshaft pulley. 3. Remove upper timing belt cover and gasket. Remove stub bolt of engine support bracket, and remove center timing belt cover. Remove lower timing belt cover. 4. Ensure camshaft, crankshaft and oil pump sprocket timing marks are aligned. See Fig. 2 or Fig. 3 . Loosen tensioner pulley center bolt. Move tensioner to relieve timing belt tension. Remove timing belt. Remove timing belt auto tensioner. See Fig. 1 . 5. Remove plug from left side of cylinder block. Install a .31″ (8.0 mm) diameter Phillips screwdriver into the hole against balance shaft. See Fig. 4 . Screwdriver must go in at least 2.36″ (60 mm) or more. If screwdriver will only go in about .79-.98″ (20-25 mm) before striking balance shaft, turn sprocket one revolution and align timing mark. Keep screwdriver in place until timing belt is installed. This ensures balance shaft driven by oil pump sprocket remains in correct position. 6. To remove timing belt “B” (balance shaft belt), hold crankshaft sprocket stationary with a spanner wrench. Remove crankshaft sprocket bolt. Using gear puller, remove outer crankshaft sprocket. 7. Remove crankshaft sensing blade (if equipped). See Fig. 5 . Loosen timing belt “B” tensioner bolt. If reusing timing belt “B”, mark direction of belt rotation for reassembly reference. Remove timing belt “B Inspection 1. Inspect timing belts for damaged teeth and cracking. Ensure belts are not contaminated with oil. Check tensioners for free rotation and grease leakage. Replace components if damaged or if grease leakage exists. 2. Check timing belt auto tensioner for leaks. Hold timing belt auto tensioner upright. Measure rod protrusion above edge of housing. See Fig. 6 . Length should be .47″ (12 mm). Apply 22-44 lbs. (10-20 kg) of force to end of rod. If auto tensioner rod moves more than 0.39″ (1 mm), replace the auto tensioner.

Related Content:

1996 nissan pathfinder timing set-up, 1996 toyota rav 4 timing belt replacement, belt diagram for 1996 toyota corola, check timing eclipse gst, timing spec diagram 1996 mitsubishi montero

Related Content:

the torque specs on a 2001 Mitsubishi Montero limited thermostat housing, 02 mitsubishi montero limited repair manual, montero crank shaft pully removal, 2003 buick 3 8 turbo engine tensioner pulley replacement youtube, MITSUBISHI CANTER 4M51 MANUAL, manuals for mitsubishi montero limited 2002, isuzu 4hk1-tc specs flywheel tension, HAW TO CHAIN SEOL VALVE THE MITSUBISHI MONTERO 3 0L 2002, free repair manual mitsubishi montero, dodge neon timing belt tensioner setting