replace oil filter adapter gasket chevy

You search PDF repair manual about replace oil filter adapter gasket chevy, if there are search results will appear below. If search results do not exist, please search by others keyword.



  replace oil filter adapter gasket chevy Direct Download speed 5432 Kb/s

  replace oil filter adapter gasket chevy Full Version speed 8172 Kb/s



1998 Chevrolet Blazer Engine Oil Cooler Hose/ Pipe Removal And Installation Manual

0

Filed Under (Chevrolet Manuals) by admin on 22-05-2012

download
Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6. Rotate the retaining ring around the quick connector until the retaining ring is out of position and can be completely removed. Discard the retaining rings. 7. Remove the engine oil cooler lines from the quick connectors at the radiator engine oil cooler inlet and outlet. Pull the lines straight out from the connectors. 8. Remove the remote engine oil filter lines support clamp bolt. Important: Have a drain pan ready for the engine oil to drain into. 9. Remove the bolt attaching the remote engine oil filter lines to the remote (frame mounted) engine oil filter adapter. 10. Hold the remote engine oil filter lines below the remote engine oil filter lines (engine mounted) adapter to drain the engine oil. 11. Remove and discard the seals. 12. Remove the bolt attaching the remote engine oil filter lines to the remote engine oil filter lines (engine mounted) adapter. 13. Remove and discard the seals. 14. Clean all of the components in a suitable solvent, and dry them with compressed air. 15. Inspect the fittings, the connectors, the cooler lines, the cooler, the filter lines, and the remote filter adapter for damage, distortion, or restriction. Replace parts as necessary. 16. Flush the engine oil cooler, the engine oil cooler lines, the remote engine oil filter adapter, and the remote engine oil filter lines with the same type of engine oil normally circulating through the engine. Installation Procedure

Related Content:

replace oil cooker 3406 cat motor, removing the oil pan on a 2008 impala 3 5, 2006 impala oil filter housing gasket, 2006 chevy trailblazer engine removal, 2012 kia srento a/c condensor drain line drawing, oil cooler on 3406 cat how to change, 2005 ford escape 2 3liter oil dipstick housing seal, oil flow path for 5 3 chevrolet, how many man hours to replace engine suburban 2007 for, clips for blazer oil cooling lines

2003 Ford Excursion, F-Super Duty 250-550 Oil Filter Adapter Removal And Installation manual

0

Filed Under (Ford Manuals) by admin on 18-05-2012

download
Removal 1. Remove the LH engine mount. For additional 6. Disconnect the oil pressure switch electrical information, refer to Engine Mounts in this connector. section. 2. Drain the engine cooling system. For additional information, refer to Section 303-03. 3. Disconnect the coolant hoses. 7. Remove the oil pressure switch. 4. Remove the oil filter. 5. Remove the threaded insert and the oil cooler. 8. Disconnect the lower radiator hose. 2. Connect the lower radiator hose. 9. Remove the nut, the bolts, the oil filter adapter and the gasket. •Discard the gasket. 3. Install the oil pressure switch. 10. Clean the gasket surface at the cylinder block. Installation 1. Position the oil filter adapter gasket and the oil filter adapter. Install the nut and bolts. 4. Connect the oil pressure switch electrical connector. 7. Connect the coolant hoses. 5. NOTE: Make sure the tab on the oil filter adapter nests into the notch in the oil cooler. Position the oil cooler on the oil filter adapter and install the threaded insert. 8. Install the LH engine mount. For additional information, refer to Engine Mounts in this section. 9. Fill the engine with clean engine oil. 10. Fill and bleed the cooling system. For 6. Install a new oil filter. additional information, refer to Section 303-03

Ford Excursion Oil Filter Adapter Removal and Installation Manual

0

Filed Under (Ford Manuals) by admin on 05-02-2012

download
Removal 1. Remove the LH engine mount. For additional 6. Disconnect the oil pressure switch electrical information, refer to Engine Mounts in this connector. section. 2. Drain the engine cooling system. For additional information, refer to Section 303-03. 3. Disconnect the coolant hoses. 7. Remove the oil pressure switch. 4. Remove the oil filter. 5. Remove the threaded insert and the oil cooler 8. Disconnect the lower radiator hose. 2. Connect the lower radiator hose. 9. Remove the nut, the bolts, the oil filter adapter and the gasket. •Discard the gasket. 3. Install the oil pressure switch. 10. Clean the gasket surface at the cylinder block. Installation 1. Position the oil filter adapter gasket and the oil filter adapter. Install the nut and bolts IN-VEHICLE REPAIR (Continued) 4. Connect the oil pressure switch electrical connector. 7. Connect the coolant hoses. 5. NOTE: Make sure the tab on the oil filter adapter nests into the notch in the oil cooler. Position the oil cooler on the oil filter adapter and install the threaded insert. 8. Install the LH engine mount. For additional information, refer to Engine Mounts in this section. 9. Fill the engine with clean engine oil. 10. Fill and bleed the cooling system. For 6. Install a new oil filter. additional information, refer to Section 303-03

2004 Honda Element EX ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) CIRCUIT HIGH VOLTAGE MANUAL

0

Filed Under (Honda Manuals) by admin on 20-06-2012

download
1. Check the engine oil level. Is the level OK? YES- Go to step 2 . NO- Adjust the engine oil to the proper level, then go to step 14 . 2. Turn the ignition switch ON (II). 3. Clear the DTC with the HDS. 4. Do the VTEC TEST in the INSPECTION MENU with the HDS. Is the result OK? YES- Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch) and the ECM/PCM. NO- Go to step 5 . 5. Check the result of step 4 . * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Failure * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Open * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) SIG Line Open * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) GND Line Open Is the test result any of the above? YES- Go to step 6 . NO- Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch). If it is OK, replace the rocker arm oil control solenoid (VTEC solenoid valve) (see step CMP SENSOR A REPLACEMENT ), then go to 14 . 6. Turn the ignition switch OFF. 7. Disconnect the rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector. 8. Check for continuity between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminals No. 1 and No. 2 Fig. 16: Checking Continuity Between Rocker Arm Oil Pressure Switch 2P Connector Terminals Courtesy of AMERICAN HONDA MOTOR CO., INC. Is there continuity? YES- Go to step 9 . NO- Replace the rocker arm oil pressure switch (VTEC oil pressure switch) (see ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) REMOVAL/INSTALLATION ), then go to step 13 . 9. Turn the ignition switch ON (II). 10. Measure voltage between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminal No. 1 and body ground

Related Content:

solenoid 2007 honda, causes of low oil pump presure on 4l60e, btsi solenoid pontiac gran prix diognose, location of oil pressure switch 2005 Honda cr-v, dt466 injection control pressure, 2007 CHEV UPLANDER LOW OIL PRESSURE, hazard switch wiring 2005 impala, 2008 gmc acadia radio no sound AND BACK POWER HATCH NOT WORKING, chevrolet silverado oil pressure sensor repair, crv honda 2004 vtech oil pressure switch

2000 Audi A6 OIL PAN (A4 And A6) Removal And Installation Manual

0

Filed Under (Audi Manuals) by admin on 01-07-2012

download
OIL PAN(A4 & A6) Removal (Lower Pan- A4 & A6) 1. Disconnect negative battery cable. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Unbolt left and right swaybar stabilizer bracket bolts (4) from mounting bracket. See Fig. 98 . Lower swaybar stabilizer not more than 10cm (3.94 INCHES) and secure with heavy wire. 4. If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) bracket from right side oil pan. 5. Remove lower oil pan. To install oil pan (lower), see INSTALLATION (LOWER OIL PAN- A4 & A6) . Installation (Lower Oil Pan- A4 & A6) 1. Ensure oil pan surfaces are clean and dry. Remove residual sealant from oil pan, if necessary, with hand drill and plastic brush instead of a flat scrapper. See Fig. 99 . Install gasket. 2. Install 2 bolts diagonal to each other (to hold up pan). Install the rest of the bolts and hand tighten. 3. Starting at center and moving outward, tighten lower oil pan to upper oil pan bolts to 10 N.m (89 INCH lbs.). Tighten oil pan drain plug 30 N.m (22 ft. lbs.). Wait 30 minutes before filling with engine oil. Tighten all bolts to specification. See TORQUE SPECIFICATIONS . 4. To complete installation, reverse removal procedure. Fill and bleed cooling system. See COOLING SYSTEM BLEEDING . Removal (Upper Oil Pan- A4 & A6) 1. Disconnect negative battery cable. Remove oil dipstick. Unbolt oil dipstick tube at front of cylinder head. Remove oil dipstick tube. 2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil. 3. Move lock carrier into service position. See LOCK CARRIER . This will allow servicing of front engine components and facilitate removal of oil pan. 4. Open coolant expansion tank cap, drain cooling system at radiator. Open the coolant pump bearing housing drain plug. Located at bottom of block near transmission bell housing, drivers side of vehicle. See Fig. 32 – Fig. 33 . If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) CAUTION: Wear eye protection NOTE: Obtain radio code before disconnecting battery. For help in identifying components and component locations, refer to illustrations Fig. 108 -Fig. 109 . NOTE: If engine is out of car, ensure oil pan is aligned with cylinder block on flywheel side. 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve 2000 Audi A6 1998-02 ENGINES’ ’2.8L V6 30-Valve bracket from right side oil pan. 5. Position Engine Support (10-222A) with (10-222A/3) engine support adapter, or equivalent, on bolted flanges of fenders. Connect support bracket to front and rear engine lifting eyes. Lift up engine as far as possible. DO NOT use excessive force to raise engine. 6. Cut tie wraps and open bracket supporting starter wiring. See Fig. 97 . Disconnect electrical connection at starter.

Related Content:

Oil Pan Gasket Leaking 2005 altima, 07 kia sportage oil pan removeing, how to change oil pan gasket 2003 chevy silverado 5 3, instutins how to replce oil PAN GASKEET ON 2006 CHEV IMPLA 5 3, ntc cummins pan bolts, oil drain pan torque 1991 corrola, oil drain plug for 3406e cat, oil pan for a 03 pontiac aztek, oildipsticktuberemoval 6 4litreford, on manual transmission how to seperate the motor from transmission

2008 Ford F-Super Duty LACKS POWER, LEAKS FLUID FROM EXHAUST PIPE, ABNORMAL TAILPIPE SEDIMENT, WHITE SMOKE, EXHAUST SMELL, AND MIL ON SERVICE PROCEDURE

0

Filed Under (Ford Manuals) by admin on 02-02-2012

download
ACTION To diagnose and correct the concern, refer to the following Service Procedure. SERVICE PROCEDURE NOTE DO NOT START ENGINE Evaluation, Inspections, And Checks 1. Retrieve KOEO diagnostic trouble codes (DTCs). 2. Check oil level. Remove and clean dipstick. Reinsert into dipstick tube only until dipstick handle reaches top of dipstick tube (Figure 1). NOTE FIGURE 1 DEMONSTRATES DIPSTICK Figure 1 – Article 07-8-9 POSITIONING FOR OVER-FULL CHECK. KEEP 3. Check coolant level. DIPSTICK HANDLE OFFSET OF CENTER TO PREVENT IT FROM FULLY SEATING. IF OIL 4. Check fuel quality. LEVEL IS BELOW THE MAX MARK, OIL IS NOT OVER-FULL. 5. Inspect tailpipes for abnormal sediment; for example black soot, white ash, oil, coolant, or fuel. 6. Inspect vehicle for coolant, oil and fuel leaks at the following locations: •Tailpipes Repair Directions •Section A – If the following DTCs are present P0087, P2291, P0263-0284, P0300-P0308, or P1336 or if observation of external fuel leaks, for example, wetness around exhaust manifolds or over-full oil level indication. •Section B – If the following DTCs are present P132B, P2262, or P2263 or observation of oil leaks (aside from over-full oil level) or oil level is low. Figure 2 – Article 07-8-9 •Section C – If coolant low or observation of 8. Replace any leaking components and verify coolant leaks. leak has been repaired while running IDS high •Sections A, B, and C – If only abnormal sediment pressure fuel system test – KOER. in tailpipes. 9. Perform WSM, Section 303-04D – Turbocharger SECTION – A Bearing Clearance Check. Fuel System Diagnostics 10. If fuel quality is poor, drain all fuel and replace with known good ultra-low sulfur diesel fuel. NOTE IN CASES WHERE ENGINE OIL HAS BEEN 11. If no DTCs were stored in pending or DILUTED WITH DIESEL FUEL AND ALL REPAIRS continuous memory go to Step 13. ARE COMPLETE, RELEASE THE OIL FILTER CAP 12. Is there abnormal sediment in tailpipes or fuel ALLOWING OIL TO DRAIN TO OIL PAN AND evident? KEEP FILTER, DRAIN THE OIL FROM OIL PAN AND FILL WITH NEW OIL. TIGHTEN OIL FILTER a. No – Complete PC/ED worksheet and CAP AND RUN ENGINE FOR 10 MINUTES. applicable PPT tests for the codes retrieved. FINALLY, CHANGE OIL FILTER AND OIL AGAIN. b. Yes – Go to Step 13. 1. If oil is not over-full – go to Step 9. 13. Is there abnormal sediment in the tailpipes?

Related Content:

ford 2014 c max service manual

OIL PAN ADAPTER INSTALLATION MANUAL

0

Filed Under (More Manuals) by admin on 24-02-2012

download
Remove the oil pan prior to installing the oil pan adapter. Refer to a factory service manual for your vehicle for reference. 2. The Oil Drain Adapter requires the oil pan to be drilled. The hole should be located above the oil level in the pan in an area that does not interfere with any other parts and that will allow oil to flow freely from the drain hose. Mark the area to be drilled. We find that typically, locating the center drain hole 1.5″from the Oil Pan Rail, provides clearance between the adapter fitting and the pan rail, and also keeps the drain hole above the oil level in the pan (See Fig. 1) . Using a scratch awl, mark the center of each bolt hole 9/16″away from the center of the center drain hole so the distance from center to center is 1.125″ (See Fig. 1) . 3. Using a center punch, indent each drilling location to prevent the drill bit from walking. Pre-drill each hole with a 1/8″bit. Secure the oil pan on a work bench or on a drill press, and drill the outer bolt holes to ¼”. Drill the center drain hole to ½”. Deburr the holes and thoroughly clean the oil pan to remove any metal shavings. 4. Install the Oil Drain Adapter onto the oil pan using the two of the ¼-20 bolts, ( Note: Select the appropriate length bolt for your application. If you have a cast aluminum oil pan, you will typically use the 5/8″long bolts; if you have a stamped steel oil pan, you will typically use the 1/2″long bolts. We recommend using blue Loctite on the threads.) and the two ¼” Stato-Seal washers on the inside of the oil pan, using the gasket on the outside of the pan (See Fig. 2a & 2b). Torque the bolts to 6-8 ft/lbs. 5. Re-install the oil pan. Refer to a factory service manual for your vehicle for reference.

Related Content:

Dodge 46rh convertor drain

OIL PAN ADAPTER INSTALLATION INSTRUCTIONS

0

Filed Under (More Manuals) by admin on 31-12-2011

download
1. Remove the oil pan prior to installing the oil pan adapter. Refer to a factory service manual for your vehicle for reference. 2. The Oil Drain Adapter requires the oil pan to be drilled. The hole should be located above the oil level in the pan in an area that does not interfere with any other parts and that will allow oil to flow freely from the drain hose. Mark the area to be drilled. We find that typically, locating the center drain hole 1.5″from the Oil Pan Rail, provides clearance between the adapter fitting and the pan rail, and also keeps the drain hole above the oil level in the pan (See Fig. 1) . Using a scratch awl, mark the center of each bolt hole 9/16″away from the center of the center drain hole so the distance from center to center is 1.125″ (See Fig. 1) . 3. Using a center punch, indent each drilling location to prevent the drill bit from walking. Pre-drill each hole with a 1/8″bit. Secure the oil pan on a work bench or on a drill press, and drill the outer bolt holes to ¼”. Drill the center drain hole to ½”. Deburr the holes and thoroughly clean the oil pan to remove any metal shavings. 4. Install the Oil Drain Adapter onto the oil pan using the two of the ¼-20 bolts, ( Note: Select the appropriate length bolt for your application. If you have a cast aluminum oil pan, you will typically use the 5/8″long bolts; if you have a stamped steel oil pan, you will typically use the 1/2″long bolts. We recommend using blue Loctite on the threads.) and the two ¼” Stato-Seal washers on the inside of the oil pan, using the gasket on the outside of the pan (See Fig. 2a & 2b). Torque the bolts to 6-8 ft/lbs. 5. Re-install the oil pan. Refer to a factory service manual for your vehicle for reference.

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, 2005 explorer transmission exploded view, 2011 crv engine whine, automatic transmission adjustments for 1997 yuko, 2003 trailblazer torque converter removal, how to check tranmission fluid on 2012 kia sedona, gm 4l60e band adjustment screws, 2008 impala 4t65e moves forward in nuetral, 1997 e450 power stroke trans mount parking brake, manual pdf transmicion automatica ram 2001

2004 Honda CIVIC Maintenance Schedule for Severe Conditions

0

Filed Under (Honda Manuals) by admin on 25-02-2011

download
30,000 miles/ 48,000 km/ — Service at the indicated distance or time, whichever comes first. Use this schedule if the vehicle is driven MAINLY in Canada or in any of the following conditions; if only OCCASIONALLY driven in these conditions, use the Normal Conditions schedule. Severe Driving Conditions ?Driving less than 5 miles (8 km) per trip in freezing temperatures, or driving less than 10 miles (16 km) per trip. ?Driving in extremely hot (over 90 ºF/32 ºC) conditions. ?Extensive idling, or long periods of stop-and-go driving, such as a taxi or a commercial delivery vehicle. ?Driving on muddy, dusty, or de-iced roads. ?Trailer towing, driving with a roof rack, or driving in mountainous conditions. Severe Driving Conditions ?Driving less than 5 miles (8 km) per trip in freezing temperatures, or driving less than 10 miles (16 km) per trip. ?Driving in extremely hot (over 90 ºF/32 ºC) conditions. ?Extensive idling or long periods of stop-and-go driving, such as a taxi or a commercial delivery vehicle. ?Driving on muddy, dusty, or de-iced roads. ?Trailer towing, driving with a roof rack, or driving in mountainous conditions. Do the items in parts A, B, C, D, E, F, G, H, I, and J as required for the mileage/time interval listed. NOTE: According to state and federal regulations, failure to do the maintenance items marked with an asterisk (*) will not void the customer’s emissions warranties. However, Honda recommends that all maintenance services be done at the recommended intervals to ensure long-term reliability. ? Replace engine oil, every 5,000 miles (8,000 km) or 6 months. ? Engine oil capacity-D17A1 engine without oil filter: 3.0 L (3.2 US qt), D17A2 and D17A6 engines without oil filter: 3.3 L (3.5 US qt). ? Replace engine oil filter, every 10,000 miles (16,000 km) or 1 year. ? Engine oil capacity-D17A1 engine with oil filter: 3.2 L (3.4 US qt), D17A2 and D17A6 engines with oil filter: 3.5 L (3.7 US qt). ? Check front and rear brakes, every 10,000 miles (16,000 km) or 1 year. ?Check pads and discs for wear (thickness), damage, and cracks. ?Check calipers for damage, leaks, and tightness of mount bolts. ?Check wheel cylinders for leaks. ?Check brake linings for cracking, glazing, wear, or contamination. ? Lubricate all hinges, locks, and latches, every 10,000 miles (16,000 km) or 1 year. ? Rotate tires, and check tire inflation and condition, every 10,000 miles (16,000 km). ? Follow the pattern shown in the Owner’s Manual. ? Inspect tie rod ends, steering gearbox, and gearbox boots, every 10,000 miles (16,000 km) or 1 year. ?Check rack grease and steering linkage. ?Check boots for damage and leaking grease. ?Check fluid lines for damage and leaks. ? Inspect suspension components, every 10,000 miles (16,000 km) or 1 year. ?Check bolts for tightness. ?Check condition of ball joint boots for deterioration and damage

Related Content:

2007 honda accord 10000 mile, 2011 kia sorento 50 000 maintenance, 2012 honda crv maintenance guide, honda crv 2011 maintenance schedule, required 2004 honda accord maintenance, saturn ion routine maintenance pdf

Related Content:

replace oil cooker 3406 cat motor, removing the oil pan on a 2008 impala 3 5, 2006 impala oil filter housing gasket, 2006 chevy trailblazer engine removal, 2012 kia srento a/c condensor drain line drawing, oil cooler on 3406 cat how to change, 2005 ford escape 2 3liter oil dipstick housing seal, oil flow path for 5 3 chevrolet, how many man hours to replace engine suburban 2007 for, clips for blazer oil cooling lines