how to replace pick up coil on 1994 chevy truck

You search PDF repair manual about how to replace pick up coil on 1994 chevy truck, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to replace pick up coil on 1994 chevy truck Direct Download speed 5432 Kb/s

  how to replace pick up coil on 1994 chevy truck Full Version speed 8172 Kb/s



1989-1996 Dodge Dakota Trucks COIL Ignition Tests Manual

0

Filed Under (Dodge Manuals) by admin on 18-06-2012

download
Dakota Trucks 1989-1996 Ignition Tests COIL The ignition coil for the vehicles covered by this guide is in the following locations: • 1989-92 engines: mounted to the firewall • 1993-96 2.5L engines: mounted on the thermostat housing in front of the coolant temperature sensor • 1993-96 V6 and V8 LDC engines: mounted to a bracket bolted to the right engine cylinder head • 1993-96 5.9L HDC engines: mounted to a bracket bolted to the air injection pump (AIR pump) mounting bracket. Fig. 2: Ignition coil mounting-all 1989-92 models Fig. 3: Ignition coil wiring and mounting hardware-1993- 96 2.5L engine 1. Inspect the ignition coil for arcing while the engine is running. If the engine will not start, this can be performed while the engine is cranked by either an assistant or a remote starter. Look at the coil in dim or low light to aid visibility of any arcing. Fig. 4: Ignition coil mounting-1993-96 3.9L and 5.2L/5.9L LDC engines 2. Arcing at the tower will carbonize the wire boot, which, if it is connected to a new ignition coil, will cause the coil to fail. In such cases, clean all the carbonization away or replace the components as necessary. Fig. 5: Ignition coil mounting-1993-96 5.9L HDC engine 3. Using a coil tester or ohmmeter according to the manufacturer’s instructions, test the primary and secondary resistance. Replace any coil that does not meet the specifications indicated in the accompanying chart. 4. Inspect the secondary coil wire for any sign of damage. Replace if any damage is found. Carbon tracking on the old wire can cause arcing and the failure of a new ignition coil. REMOVAL & INSTALLATION 1989-92 Models See Figures 6 and 7 1. Disconnect the negative battery cable. 2. Disconnect the three wires from the coil. Mark them to identify for installation. Fig. 6: Remove the coil bracket bolt at the cowl Fig. 7: Unscrew the coil mounting hardware, then remove the coil from the vehicle 3. Unplug the condenser suppressor connector from the coil, if equipped. 4. Unbolt and remove the coil. To install: 5. Bolt down the coil with old bolts. 6. Connect wires to coil making sure that the proper wires are connected where they should be. 7. Connect the condenser suppressor, if equipped. 8. Connect the battery negative cable Removal and Installation V6 AND V8 ENGINES 1. Disconnect the negative battery cable. 2. Disconnect the primary wiring from the ignition coil. 3. Disconnect the secondary spark plug wire from the coil. 4. Remove the two bolts and withdraw the coil from its mounting bracket. To install:
5. Position the coil on its bracket and install the two bolts. Tighten them to 100 inch lbs. (11 Nm). If the bracket has been tapped for coil mounting bolts, these fasteners require less torque, so tighten them to 50 inch lbs. (5 Nm). 6. Connect all wiring to the ignition coil. TESTING See Figure 1 The only test you can perform without a DRBII scan tool, or equivalent, is a basic check of the sensor only.

Related Content:

ciol wire problems 2007 camry, priceofcoylepackfora2005kiasedona, chevy 230 cid primary resistor, no power to coil on 1993 dakota, test coil dodge dakota 1993, Isuzu 1997 wiring diagram between coil distibutor, Remove Evap coil from honda element, 1996 dodge dakota 2 5 temperature sensor diagram, replace individual coils on 2002 mercury mountaineer, replacing evaporator on 1999 gmc truck

2004-2006 Chevrolet Malibu, Malibu Maxx Loss of Power Steering Assist, Power Steering Warning Message Displayed in DIC, IPC/Radio Displays Erratic, DTC C0900, B1325 Set (Replace Ignition Coil/Module Assembly and Add Ground Strap)

0

Filed Under (Chevrolet Manuals) by admin on 10-01-2012

download
Correction Replace the ignition coil/module assembly and add ground strap following the procedure below. 1. Disconnect the ignition coil electrical connector. 2. Disconnect the left side spark plug wires from the ignition coil. 3. Disconnect the right side spark plug wires from the ignition coil. 4. Remove the four bolts attaching the ignition coil to its mounting bracket and remove the ignition coil. 5. Remove the ignition coil from the mounting bracket. 6. Loosen the two lower ignition coil mounting bracket nuts. 7. Remove the two upper ignition coil mounting bracket bolts and discard. Subject: Loss of Power Steering Assist, Power Steering Warning Message Displayed in DIC, IPC/Radio Displays Erratic, DTC C0900, B1325 Set (Replace Ignition Coil/Module Assembly and Add Ground Strap) Models: 2004-2006 Chevrolet Malibu, Malibu Maxx with 3.5L Engine (VINs 8, N — RPOs LX9, LZ4) 8. Install the ground strap (1), P/N 12581176, to the upper left side of the bracket as shown between the coil bracket and intake. Install the new bracket bolt, P/N 11570082, (do not tighten at this time). Prior to installing the ground strap, remove the captured nut and washers. They are not needed (simply pound them out with a hammer on a vise). 9. Install the washer (2), P/N 02436162, to the upper right side of the bracket between the coil bracket and intake. Install the new bracket bolt, P/N 11570082, (do not tighten at this time). Tighten Tighten all the ignition coil bracket bolts and nuts to 25 N·m (15 lb ft). 10. Install the new ignition coil to the mounting bracket. 11. Install the other end of the ground strap to the coil as shown and secure using a new bolt, P/N 11588715. 12. Install the other three ignition coil bolts. Tighten Tighten the bolts to 10 N·m (89 lb in). 13. Connect the right side spark plug wires to the ignition coil. 14. Connect the left side spark plug wires to the ignition coil. 15. Connect the ignition coil electrical connector

Related Content:

Owners Manual 2004 Chevy Malibu Maxx, malibu ml60t manual, how to replace a ignition coil on 2004 toyota sienna, diagram for ignition wires on a 1998 sebring 2 5l, 1999 saturn replacement ignition switch bolts, repair of saab ignition coil, mazda speed 6 ignition module, 2006 pontiac torrent replacement ignition, 2006 Malibu Maxx Owners Manual, 2006 chevy malibu spark plug lications

Malfunction Indicator Lamp (MIL) Illuminated, DTCs P0300-P0306, Engine Runs Rough (Inspect for Water Intrusion in Spark Plug Recess Area, Replace Spark Plug and Ignition Coil, Seal Ign Coil Bolt Hole)

0

Filed Under (More Manuals) by admin on 18-01-2012

download
1. Observe the Misfire Current Counters parameter with a scan tool, in order to determine the affected cylinder(s). 2. Remove the air cleaner resonator and outlet duct. Refer to Air Cleaner Resonator and Outlet Duct Replacement in SI. 3. Disconnect the engine wiring harness electrical connectors from the affected ignition coil(s). Refer to Ignition Coil Replacement in SI. 4. Remove the ignition coil bolt(s) and ignition coil(s) from the camshaft cover. Refer to Ignition Coil Replacement in SI. Note: If water is observed in ANY of the spark plug recess areas, then it will be necessary to apply Loctite® 565 PST Thread Sealant* to ALL of the ignition coil bolt hole vents and bolt threads. 5. Inspect for water intrusion in the spark plug recess areas. Warning: Wear safety glasses when using compressed air, as flying dirt particles may cause eye injury. 6. If any water is present, then remove the water from the spark plug recess areas with low pressure air. 7. Remove the affected spark plug(s) from the cylinder head. Refer to Spark Plug Replacement in SI. 8. Replace ONLY the affected spark plug(s) with new spark plug(s) as needed into the cylinder head. Refer to Spark Plug Replacement in SI. 9. Fill the bottom of the ignition coil bolt hole vent with Loctite® 565 PST Thread Sealant* as indicated in the illustration, and apply it to the ignition coil bolt threads also. 10. Replace ONLY the affected ignition coil(s) with new ignition coil(s) as needed. Refer to Ignition Coil Replacement in SI. 11. Connect the engine wiring harness electrical connectors to the ignition coil(s). Refer to Ignition Coil Replacement in SI. 12. Replace the air cleaner resonator and outlet duct. Refer to Air Cleaner Resonator and Outlet Duct Replacement in SI. 13. Clear the DTCs with a scan tool.

Related Content:

07 g5 ignition housing, 09 chevy silverodo how to replace ignition lock cylinder, 1991 ford explorer ignition cylinder disasembly, 2002 crv ignition lock replacement, 2007 chevy suburban cylinder diagram, ford taurus ignition cylinder repair, ignition cylinder lock FOR KIA DIAGRAM, toyota avalon spark plug 2005

Coil Spring Spacer Installation Instructions

0

Filed Under (More Manuals) by admin on 24-12-2011

download
1. Check to see that the spacer kit you purchased matches the year and model of your vehicle. Spacer kits two inches or taller may require a spring compressor to install. Ball joint and tie rod forks may also be useful. 2. A good portion of your front suspension will be disassembled so this would be a good time to replace any worn parts (i.e. tie rod ends, ball joints, idler arm and any bushings) Replace bushings with polyurethane replacement parts. 3. Jack up vehicle as high as possible using jack stands for support at all times. 4. With vehicle safely off the ground remove front tires. It is advisable to disassemble on side at a time so that you can use the other side as a reference for re-assembly in the event you get side tracked. 5. Remove the brake caliper from the rotor (attached with 2 bolts inside the caliper or with press-in clips depending on the vehicle). Do not remove the brake line from the caliper unless you intend to bleed the brakes at this time. Set the caliper aside or tie it up to the frame rail. Avoid pinching the brake line. 6. Remove the tie rod from the spindle using the proper tools. Do not hit the tie rod itself or the nut on the threaded portion of the tie rod or it may cause damaged and need replacing. 7. Remove the anti-sway bar from the lower control arm. This would be a good time to replace the end link bushings with polyurethane replacement bushings. 8. If your vehicle is equipped with anti-lock brakes you must now disconnect the front rotor sensor from the dust shield or spindle and set it aside. 9. Disconnect your shock absorber completely from the vehicle whether it is mounted inside the coil spring or not. 10. Support the lower control arm with jack just touching the arm. This will prevent it from dropping when the ball joint is disconnected. 11. The use of a coil spring compressor is recommended before the following steps are taken. 12. Disconnect the upper ball joint from the top of the spindle using the proper tools. Do not hit the ball joint or the threaded end of the ball joint. Once the ball joint is free the spindle should move easily. 13. Be careful when lowering the lower control arm. The coil spring is under high compression and may shoot out when released. Do not stand near the side of the truck during this step. Lower the jack so that the lower control arm swings down. If the coil spring has not fallen out on it’s own you may need to use a pry bar from the front of the vehicle to remove it. 14. Note which end of the coil spring is “bottom” for installation. Also note the depression in the lower control arm. It is important that the last winding of the coil spring fit into the indentation completely so that the vehicle will sit level. Do not switch coil springs from side to side as some vehicles have a specific “right” and “left” coil spring. 15. Check the coil spacer for proper fitment into the coil spring mount in the frame. The flat part of the spacer should face up and touch the top of the spring mount. Some vehicles have guiding tabs to center the coil spring in its top mount. These tabs may have become bent and need to be bent back to allow the spacer to properly fit in the mount. 16. Install the coil spring with the spacer on top of it. If used the coil spring compressor should still be on the spring in a compressed state. If it is not you may need to compress the spring before re-installing. Make sure the spacer is centered in the upper mount and the bottom of the spring is properly nested in the receptor groove on the lower control arm. If you are installing a two-inch or taller spacer you may need a spring compressor. Follow all safety rules when installing the coil spring as it will be under extreme compression. 17. Raise the lower control arm with a jack once the coil spring and spacer are properly lined up. Raise until the spindle is high enough to bolt on the upper ball joint. Before bolting on the upper ball joint make sure the brake caliper and brake line are where they need to be since some brake lines run inside the spindle and outside the coil spring. 18. With the upper ball joint tight and a cotter pin re-installed you may now remove the jack from under the lower control arm. 19. Assemble all of the components previously removed (sway bar with new polyurethane bushings, tie rod ends with polyurethane grease boot, brake caliper and anti-lock sensor). Don’t forget the shock with a new colored boot while it is off. 20. Repeat instructions for other side. 21. After properly installing both spacers you can install your front tires and lower vehicle back to the ground. 22. Your vehicle may sit too high at first because the suspension needs to settle. Carefully back the vehicle up and drive forward a few times using the brakes frequently. Park on level ground and check out your lift. 23. The vehicle will now require a front wheel alignment. Failure to do so may result in severe wear on your tires and may pull to one direction

Related Content:

1997 ford ranger coil spring spacer installation, 4L60E 3 4 Accumulator Assembly, how to replace rear coil spring on a buick rendezours, how to use evertough coil spring compressor, Jeep TJ coil spring perch, labor to replace control arms g6, metal clip on ow beam 2009 mazda 6, ranger coil spring replace, replace 2006 Impala control arm bushings, replacing rear springs for 2004 toyota sienna

Ford 2″ Coil Spring Spacer Kit with Stud Extenders INSTALLATION INSTRUCTIONS

0

Filed Under (Ford Manuals) by admin on 18-12-2011

download
INSTALLATION INSTRUCTIONS 1. Read complete instructions and check Bill of Materials before beginning. 2. Raise the front of the vehicle and support the frame so that the front tires just touch the ground and remove the front tires. 3. Remove the lower shock bolts and the sway bar end link attaching points. 4. Remove the upper and the lower coil spring clamp bolt and nut with washer. See figure 1 and 2. 5. Force the axle half down so that the coil spring comes loose. 6. Remove the coil spring and the coil spring rubber isolator. See figure 3. 7. Install the corresponding Stud Extensions (if needed) onto the coil spring lower clamp stud and install the coil spring spacer onto the coil spring pad. See figure 4. 8. Install the coil spring onto the coil spring spacer and then into the frame. You may have to use a coil spring compressor. See figure 5. 9. Install the upper and the lower coil spring clamp bolt and nut with washer. Make sure that the coil spring is seated correctly into the upper frame. See figure 6 and 7. 10. Reconnect the sway bar end link attaching points and the shock nuts. 11. Torque all bolts and nuts to factory specifications. Re-torque all bolts and nuts after 500 miles. 12. Install front tires and remove the jack stands. Lower the vehicle onto the ground. 13. It is recommended that you have a front-end alignment Ford 2″ Coil Spring Spacer Kit with Stud Extenders INSTALLATION INSTRUCTIONS

Related Content:

do I reinstall the factory spring insulator when installing front spring levelling kit on 2007 dodge ram

2006 Dodge Truck RAM 2500 DENSO A/C COMPRESSOR Service and Repair Manual

0

Filed Under (Dodge Manuals) by admin on 23-01-2012

download
DENSO A/C COMPRESSOR REMOVAL NOTE: * The compressor clutch assembly can be serviced with the refrigerant system fully-charged. * Typical A/C compressor shown in illustrations. 1. Disconnect and isolate the negative battery cable. 2. Remove the accessory drive belt. 3. Disconnect the engine wire harness from the compressor clutch field coil connector (1) located on the top of the A/C compressor (5) . Remove the bolts that secure the A/C compressor to the engine and support the A/C compressor. 5. Carefully remove the compressor clutch field coil connector and wire lead from the connector bracket (2). 6. Remove the compressor shaft bolt (3). A band-type oil filter wrench or a strap wrench may be used to hold the clutch plate (4) from rotating during bolt removal. CAUTION: Do not pry between the clutch plate and the pulley and bearing assembly to remove the clutch plate from the compressor shaft as this may damage the clutch plate. NOTE: Use care not to lose any clutch shim(s) during removal of the clutch plate, as they may be reused during the clutch plate installation process. 7. Tap the clutch plate (2) lightly with a plastic mallet to release it from the splines on the compressor shaft (1) and remove the clutch plate and shim(s) (3). 8. Using snap ring pliers (2), remove the snap ring (1) that secures the pulley and bearing assembly (3) to the front of the A/C compressor and remove the pulley and bearing assembly. 9. Using snap ring pliers (Special Tool C-4574 or equivalent) (1), remove the snap ring (4) that secures the compressor clutch field coil (2) to the front of the A/C compressor (3) and remove the field coil. INSTALLATION NOTE: Typical A/C compressor shown in illustrations. 1. Align the dowel pin on the back of the compressor clutch field coil (2) with the hole in the front of the A/C compressor (3) and position the field coil onto the compressor. Be certain that the compressor clutch field coil wire lead is properly routed so that it is not pinched between the A/C compressor and the field coil. CAUTION: The snap ring must be fully and properly seated in the groove or it will vibrate out, resulting in a clutch failure and severe damage to the A/C compressor. NOTE: A new snap ring must be used to secure the compressor clutch field coil to the A/C compressor. The bevel side of the snap ring must face outward and both snap ring eyelets must be oriented to the right or to the left of the field coil dowel pin location on the A/C compressor. 2. Using snap ring pliers (Special Tool C-4574 or equivalent) (1), install the snap ring (4) that secures the compressor clutch field coil to the front of the A/C compressor. Be certain that the snap ring is fully and properly seated in the groove and oriented correctly. CAUTION: * Be certain to position the compressor clutch field coil wire lead so that

Related Content:

1994 mazda b3000 how to replace clutch and slave free download, 2004 f250 ac compressor replacement, changing Saab 93 clutch 2003, air compressor for 2003 pontiac bonneville ssei, hummer h1 ac compressor wiring, 87devillebrakelightswitchcausingona/c, scion xb compressor control solenoid problems, 2004 chevy cavalier torque specs clutch, starter clutch cvt trans mission honda rebuilt, Snap on Eedm504d User Manual

1999-2004 Jeep Grand Cherokee WJ 2″ Coil Spring Spacers Installation Manual

0

Filed Under (Jeep Manuals) by admin on 19-12-2011

download
FRONT 1. Read complete instructions before beginning installation, the following special tools are recommended: Coil spring compressor, floor jack, jack stands, and metric hand tools. 2. Jack the vehicle in the center of the front axle. 3. Support the vehicle by placing jack stands on the frame behind the control arms so that the front tire/wheels are off the ground freely. 4. Remove the front tires/wheels. 5. Remove the lower shock nuts that secure the shock to the axle on both sides. 6. Remove the coil springs. 7. Remove the upper coil spring isolator and install onto the coil spring spacers. 8. Starting on the left side of the vehicle install the coil spring spacer onto the frame. 9. Install the coil spring. Note the position of the spring as it seats into the lower coil spring isolator on the axle so that it is at its stop. It must be seated into the coil spring isolator. 10. In order to complete step # 9 on the right side of the vehicle you may have to use a coil spring compressor in order to install the coil spring. You may also disconnect the lower lateral track bar on the front end. 11. Jack the axle and reconnect the lower shock nuts that secure the shock to the axle. 12. Install the front tires/wheels. 13. Lower the vehicle onto the ground. 14. Torque all bolts to factory specifications and re-torque after 500 miles.. 15. Daystar recommends having the front end alignment checked after installing the coil spring spacer lift

Related Content:

grand cherokee spring spacer install

TOYOTA TACOMA DC XSB RETRACTABLE HARD TRUCK BED COVERS INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 26-09-2011

download
STEP 1: POSITIONING CANISTER Remove the top cover from the canister box and set it aside for later installation. Perform a quick inventory to insure all parts are there. Be sure to check inside the small cardboard box for parts. Remove the Canister from the box and set it in the truck bed against the cab. The canister should be resting on the canister end plates and be centered in the truck bed. DO NOT USE A KNIFE TO OPEN THE RAIL BOX. OPEN THE RAIL BOX ALONG THE LENGTH OF THE BOX AND LIFT RAILS OUT TO AVOID SCRATCHING THE SURFACE OF THE RAILS ON THE PACKAGE STAPLES. CAUTION! Canister End Plates INSTALLATION INSTRUCTIONS Slide the four (4) Inner Rail Clamps (2 on each side) through the Tie Down Bars of the truck. (Figure 2B) Place the Outer Angled Rail Clamps on the Inner Rail Clamps (MAKE SURE THE NARROWER EDGE IS DOWN ON THE OUTER ANGLED RAIL CLAMPS) loosely fasten the clamps in place with the 1/4″ Washer, 1/4″ Lock Washer and Rail Clamp Nut on both sides of the truck bed. The fi rst clamp should be placed about 6 inches from the canister (closest to truck cab). The second clamp assembly should be about 4 inches from the end of the Tie Down Bar (closest to the tailgate). Open the rail box along the length of the box, lift rails out to avoid scratching the rail surface on the package staples. The side rails are marked “left” and “right” (left is the driver’s side of the truck). Then Slide Rail Clamp Bracket A on each Rail followed by Rail Clamp Bracket B. Rail Clamp Bracket A should be closest to the Cab of the truck. At this time you will need to install the taligate end of the pull strap to the underside of the drivers side rail using the #8-32 x 3/4 machine screw that is already located at the tailgate end on the underside of the rail. (Figure 2A) Now, with the tailgate closed, place the side rails in position on the truck bed with the Rail Clamp Brackets A & B resting on the Outer Angled Rail Clamps. Loosely assemble the Rail Clamp Brackets to the Outer Angled Rail Clamps with the 1/4″ Washer, 1/4″ Lock Washer and 1/4-20 x 1/2″ Bolt on each side of the truck bed. Center the Rails in the Truck bed. Check spacing in the truck bed between the Left and Right Rails. Spacing should be 51 3/4″. Once correct spacing is achieved tighten the Rail Clamp Brackets A & B only in place Correct spacing to the tailgate should be 1/16″ to prevent the tailgate from striking the side rails when closing. Tighten the Set Screws on both Rail Clamp Bracket A to hold rails in position. ( Adjust spacing from the tailgate by moving rails forward or backward as needed prior to fi nal tightening of set screws .) Apply downward pressure while tightening the Outer Angled Rail Clamp to the Inner Rail Clamp, especially on the tailgate end. This will ensure a tight seal, fi rm seat, and good fi t on the truck bed

Related Content:

Tail Gate mounting Instructions on A25 Volvo Truck, 1954 f100 owners manual, hino truck repair manual, how to install cross rails on buick enclave, instructions on how to install roof rack cross rails on a 2014 Buick Enclave, isuzu npr dashboard guide, Isuzu NPR PRNDL inoperative, kia sedona frame structure, manual 1993 s10 truck, repair Evap soleniod for 2006 chevy 1500

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, gm 4l60e band adjustment screws, how to check tranmission fluid on 2012 kia sedona, 2003 trailblazer torque converter removal, 2011 crv engine whine, 2005 explorer transmission exploded view, automatic transmission adjustments for 1997 yuko, 1997 e450 power stroke trans mount parking brake, transmission module for 1999 ford ranger xlt, manual pdf transmicion automatica ram 2001

Dodge Ram 4WD Front Leveling Kit Installation Instructions

0

Filed Under (Dodge Manuals) by admin on 19-12-2011

download
1. To begin installation, block rear wheels and apply parking brake so that the vehicle is stable and cannot roll forward or back. Lift front of the vehicle on appropriate lift points, such as the frame, and support the frame with jack stands on both passenger and driver sides. Remove front wheels. 2. Position a floor jack under the front axle and raise jack until it makes contact with the front axle. (See Figure 1) 3. On the drives side, place an index mark on the stock coil spring and another index mark directly across from the first mark on the lower coil spring perch. This will allow you to reinstall the stock coil spring in its original position. Repeat step 3 on passenger side. 4. Disconnect top nut on sway bar end links on driver and passenger side, set nut, retainer, and bushing aside. Pivot sway bar up and out of the way. (See Figure 1) 5. Disconnect nut from passenger side drag link (outer tie rod end). Hit steering knuckle with a hammer at the point where the drag link stud comes through. This will break the stud loose from the steering knuckle. Breaking the stud loose may require the use of a ball joint separator. Gently tap the stud down through the knuckle. Be careful not to harm the stud or stud threads. Moving this out of the way allows access to the passenger lower shock bolt. (See Figure 1) 6. On driver’s side, locate the top of shock absorber stud, located in the engine compartment. Remove the top nut, retainer washer, and grommet from the shock. (See Figure 2) NOTE: Save these parts, they will need to be reinstalled later. Repeat step 6 on passenger side. 7. On driver’s side, remove the (3) stock nuts from the upper shock tower and set upper shock tower aside for reinstallation later. (See Figure 3) Repeat step 7 on passenger side. 8. On driver’s side, remove bolt from the lower shock mount through access hole below the coil spring. Save hardware for reinstallation. Remove shock from access in engine compartment. (See Figure 4) Repeat step 8 on passenger side. 9. Carefully lower floor jack enough to allow the removal of the stock coil spring. On driver’s side, remove the coil spring and the rubber isolation pad and set aside for later reinstallation. Remove ring that retains the shock tower bolts and discard . Repeat step 9 on passenger side. NOTE: Removal of the passenger coil spring may require the use of a spring compressor. 10. Lower the floor jack to allow room for the stock coil spring and the new upper coil spacer. 11. On the driver side, place the isolation pad on top of the stock coil spring, place new coil spring spacer on top of isolator pad. Place the entire assembly into the stock spring location. Turn the spring so that it is lined up with index marks made in step 3. Line the spacer studs up with the holes in the shock tower. Raise the floor jack until new coil spring spacer seats into the upper stock location. (See Figure 5) Repeat step 11 on passenger side. 12. On the driver’s side, install the shock down through the engine compartment and secure the bottom of the shock into the stock location using the stock hardware. Tighten to 100 ft-lbs. Repeat step 12 on passenger side. 13. On the driver’s side, reinstall stock upper shock tower into stock location. Secure new coil spring spacer to upper shock mount using 3/8″ hardware provided with the kit. Torque to 35 ft-lbs.

Related Content:

Disassemble front shock and coil spring 2010 Dodge Ram, what parts are needed to replace rear struts in pontiac vibe, diagram lower ball joint 2005 dodge ram 1500 4×4, e350 rv shock bolts, troubleshoot ford code C1725

Related Content:

ciol wire problems 2007 camry, priceofcoylepackfora2005kiasedona, chevy 230 cid primary resistor, no power to coil on 1993 dakota, test coil dodge dakota 1993, Isuzu 1997 wiring diagram between coil distibutor, Remove Evap coil from honda element, 1996 dodge dakota 2 5 temperature sensor diagram, replace individual coils on 2002 mercury mountaineer, replacing evaporator on 1999 gmc truck