how to replace rack and pinion seals trailblazer

You search PDF repair manual about how to replace rack and pinion seals trailblazer, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to replace rack and pinion seals trailblazer Direct Download speed 5432 Kb/s

  how to replace rack and pinion seals trailblazer Full Version speed 8172 Kb/s



2005 Ford F-150 Drive Pinion Flange and Drive Pinion Seal Repair Manual

0

Filed Under (Ford Manuals) by admin on 21-04-2012

download
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02 . 2. Remove the brake disc. For additional information, refer to Section 206-04 . 3. Index-mark the driveshaft flange and pinion flange for correct alignment during installation. 4. Remove the 4 driveshaft flange bolts. 5. NOTE: The driveshaft centering socket yoke fits tightly on the pinion flange pilot. Never hammer on the driveshaft or any of its components to disconnect the driveshaft centering socket yoke from the pinion flange. Pry only in the area shown with a suitable tool to disconnect the driveshaft centering socket yoke from the pinion flange. Using a suitable tool as shown, disconnect the driveshaft centering socket yoke from the pinion flange. ? Using mechanic’s wire, position the driveshaft aside. 6. Using a Nm (lb-in) torque wrench on the pinion nut, record the torque required to maintain rotation of the pinion gear through several revolutions. 7. Using the special tool to hold the pinion flange, remove and discard the pinion nut.2005 F-150 Workshop Manual 8. Index-mark the pinion flange in relation to the drive pinion stem to make sure of correct alignment during installation. 9. Using the special tool, remove the pinion flange. 10. Force up on the metal flange of the drive pinion seal. Install gripping pliers and strike with a hammer until the drive pinion seal is removed. Installation 1. Lubricate the new drive pinion seal with grease. 2. Using the special tool, install a new drive pinion seal. 3. Lubricate the pinion flange splines with axle lubricant. 4. NOTE: Disregard the scribe marks if a new pinion flange is being installed. Align the pinion flange with the drive pinion shaft. 5. Using the special tool, install the pinion flange. 6. l a new pinion nut with the same iginal if not replacing the collapsible spacer. If a installed, install the nut in the kit, as indicated in the chart below, or damage to the component may occur. Position the new pinion nut. Pinion Nut 7. no circumstances ut to be backed off to reduce drive pinion bearing preload. If reduced drive pinion bearing preload is required, a new drive pinion collapsible spacer and pinion nut must be installed or damage to the component may occur. NOTE: Remove the special tool while taking drive pinion bearing preload readings with the Nm (lb-in) torque wrench. Using the special tool to hold the pinion flange, tighten the pinion nut. ? Rotate the drive pinion occasionally to make sure the drive pinion bearings are seating correctly. ? Install a Nm (lb-in) torque wrench on the pinion nut. ? Rotating the drive pinion through several revolutions, take frequent drive pinion bearing preload readings until the original recorded drive pinion bearing preload reading is obtained. ? If the original recorded drive pinion bearing preload is lower than specification, tighten to the appropriate specification for used drive pinion bearings. If the drive pinion bearing preload is higher than specification, tighten the pinion nut to the original reading as recorded. For additional information, refer to the Specification portion of this section. 8. Position the driveshaft and align the index mark on the pinion flange.

Related Content:

guide differential f53 1997, replacing 94 camaro rack and pinion, how to repair noise driveshaft in a ford expedicion 2001, cummins n14 accessory drive torque specs, cost to replace a rack and pinion on 2002 suburban, 2004 ford f150 yoke, meritor pinion seal installer, mercedes exhaust pipe torque spec, mercury drive shaft socket, how to change rack and pinion 05trailblazer

Troubleshooting and Resolving Water Leaks for FUNSPORT Sunroofs

0

Filed Under (More Manuals) by admin on 13-03-2012

download
1. Opening the sunroof, just after it rains. Standing water on the glass will usually result in water dripping into the cabin. This is not a sunroof fault. Prevention is the solution! Simply drive a short distance to allow any standing water to blow off the glass prior to opening the sunroof. 2. Only after a car wash. High pressure water sprayed directly at the seal will often deflect the seal enough to enter the cabin. This is not a sunroof fault. Prevention is the solution! Don’t spray high pressure water directly on the seal. 3. During a rainstorm, water is immediately visible dripping on the rubber seal under the glass. There may be a problem with glass to seal contact. Carefully examine the seal. If it is visibly damaged or worn, it may need replacement. If dirty, it needs cleaning. An adjustment may solve the problem. Always water test to verify (see sprinkle test procedure below). a. Often dirt or debris will prevent proper contact between the glass and seal. Clean both the glass and seal with plain water (a damp cloth), or if very dirty, a mild detergent solution. Repeat water test after cleaning. If water intrusion between glass and seal continues, adjust the glass hardware. b. Adjust the glass hardware to increase clamping pressure on the seal. See procedure below. Repeat water test after adjusting. If water intrusion between glass and seal continues, replace seal. 4. Water is visible dripping through the glass hardware: Water test to verify (soak and sprinkle). You may need to slightly shift the glass hardware or change the rubber gaskets under the rectangular mounting plates. 5. After a long soaking rain the headliner gets wet. This is likely the result of water coming under the main frame or under the seal. Only a soak test will prove this. a. Under the main frame: remove the screw cover strip or pull back the headliner (of wrapped) and examine the clamping screws. Water spots or rusty screws are an indication that water is coming under the main frame. Remove the clamp frame and water spots or rust will likely be visible on the inside of the roofskin. This can be the result of an over-cut hole, a sunroof not centered on the hole (left a gap) or inadequate sealant. Solution: Remove the sunroof and re-install with new sealant. If the hole was over-cut, a larger size may be required. b. Underneath the main seal: carefully examine and verify proper seal insertion around perimeter of sunroof frame. Bottom of seal should be adhered to main frame with butyl tape. Top outer lip should be mechanically inserted into groove in frame. You may be able to manipulate the seal slightly to correct the problem. Otherwise replace the seal. c. Frame joint: typically will see water spots or rust on hinge block and handle mounting screws, particularly on the right hand side. Remove the knock-in bead and examine the channel for water or water spots. Solution: pull back the main seal at the passenger side and apply a small amount of silicone sealant across the frame joint. Allow to dry before reinserting the main seal.

Related Content:

1997 lumina 3 1l thermostat adjustment dial?, seal for slip on muflers, how to seal compresion hose leak on 2000 bmw 528i, rear main seal leak 2006 suburban, rear seal replacement on 2003 Chevy Cavalier, reinstall 1929 ford rear glass replacement, removing axles 1998 ford expedition, Replacing rear main seal 2003 suburban, ridgeline rear main seal tsb, to change seal on 2003 camshaft sensor

RICHMOND GEAR INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 19-03-2012

download
VERIFY RATIO BEFOREASSEMBLY STEP 1 . Remove the gears to be replaced and thoroughly clean both the gear carrier and housing with solvent to remove any gear/bearing residue, which could lead to abrasive failure of the new gear set. After cleaning, dry- wipe (or air-dry) all disassembled parts, housings, and covers. STEP 2. Examine the ring gear mounting surface for nicks or burrs which might prevent total landing of the newly installed ring gear. Ring/pinion tooth depth variations can result from a ring gear that is “cocked”on its mounting surface. If a ring gear spacer is to be used, also check it for similar surface imperfections, dressing these with block backed pieces of grit paper or a small file. Following material removal (from ANY part of the assembly), bathe the pieces in the solvent and wipe or air-dry. NOTE: Spacers not normally recommended STEP 3. Study the illustrations provided with these instructions. Familiarize yourself with the terms “backlash”and “pinion depth” (sometimes called checking distance). Each set of gears is a matched pair which has been prerun on a gear test machine. Consequently, the pair should never be mixed with other rings or pinions, Also, since all gear sets have been run-checked, specific settings are supplied with each ring/pinion pair. These specifications vary from set to set. Backlash settings are marked on the outside diameter face of the ring gear as follows (see illustration A): Ref: BL.008, which means a backlash figure of .008 inch at the closest point. Pinion depth settings (or checking distance) are marked on the face of the pinion gear as follows (see illustration B): Ref: CD 2.799, which means distance of 2.799 inches from centerline of the ring gear to pinion face. Dimensional variations for backlash SHOULD NOT EXCEED .004″variation. Example: If backlash is .008, the backlash — including maximum variation — should be .008-.012. 1 Illustration B Location of checking distance (pinion depth) & serial no. on pinion Location of backlash dimension & gear serial no. on ring gear Illustration A STEP 4. When installing the pinion gear you must check its depth in the housing as per the pinion depth dimension. Add or subtract pinion depth shims to arrive at the checking distance etched on the surface of the pinion face. (See illustration C.). Refer to Helpful Hints & Additions to Richmond Gear Installation Instructions on pages 3 and 4. STEP 5. Using a mew crush collar or preload shim pack, set the pinion rotating torque to 10-15 (used bearings) 20-25 (new bearings) inch pounds. For oval track applications when not using a cooling pump, set at 16- 17 inch pounds on new bearings and 10 inch pounds maximum on used bearings. STEP 6. After correct installation of the pinion gear, position the ring gear and check for backlash. Mount a magnetic-base dial indicator on the axle housing in such a way that the indicator plunger will be moving in a line that is tangent to rotation of the ring gear. This will provide you with a backlash reading which should conform to the figure etched on the side of the ring gear. Again, maintain a tolerance of .004 variation. Example: If backlash is .008, the backlash – including maximum variation – should be .008-.012. (Backlash is always measured in 3 or more places equally spaced around in the ring gear.) Note: For oval track racing set BL at approximately .012-.014 inches. STEP 7. Compensation for variations in this setting can be made by side-adjustment of the ring gear. Adjusting rings or side-shim packs can be changed to bring the backlash and rotating torque figures into tolerance. (Use same torque on gear bearings as on pinion bearings.) You are now ready to check the tooth contact pattern to assure that no accidental departures from the factory- marked specifications have been made. Apply a thin coat of RICHMOND GEAR compound (“Part # 55-0001- 1″) on gear teeth for best results. Tooth contact patterns should comply with those shown on next page. (Note rounded or bullet nose shape at heel end of pattern on Gear drive sides). See page 4 for patterns and additional installation hints

Related Content:

gear backlash procedure for cat, how to remove 2007 eatc o ringgs, governor install stanadyne injection, Richmond Gear Installation, pinion checking distance, 580 e ring gear full set, FORD DIFFERENTIALS: HOW To adjust heel toe pinion and ring gear, checking pinion depth, caterpillar transmission backlash tool, 97 grand am horn assembly replacement

1997 Jeep Grand Cherokee Laredo 7 1/8″, 7 1/3″, 7 9/16″, 7 4/5″, 8 1/4″, 8 1/2″ & 8 9/10″ Ring Gears Removal And Installation Manual

0

Filed Under (Jeep Manuals) by admin on 04-07-2012

download
Removal (Model 194, 8 1/4″ & 1998 Grand Cherokee 216 Axles) 1. Raise and support vehicle. Remove rear wheel(s). If equipped with drum brakes, remove brake drum. If equipped with disc brakes, remove brake caliper and rotor. On all models, clean axle housing cover. Loosen cover bolts, and drain oil. Remove cover. 2. Remove differential pinion-shaft lock bolt. Remove pinion shaft from differential. Push in axle. Remove “C” clip from axle at pinion gear. Remove axle from tube. Remove axle shaft seal and bearing from axle tube. Installation 1. Grease bearing, and install into axle tube. Ensure bearing part number is facing outwards. Apply wheel bearing grease to axle shaft seal. Install seal in axle tube. Install axle shaft. 2. Install axle “C” clip. Pull axle out to seat “C” clip. Install pinion shaft. Install lock bolt, and tighten to specification. Apply RTV to axle housing cover. Tighten cover bolts to specification. See TORQUE SPECIFICATIONS table. Fill with gear oil. Removal (Model 198, 1999 Grand Cherokee 216 & 226 Axles) 1. Raise and support vehicle. Remove rear wheel(s). Remove brake drum. Remove nuts securing axle retainer plate to axle tube, and discard. Using slide hammer and Adapter (6790), remove axle shaft from axle tube. 2. Using a 3/8″ drill bit, drill a shallow hole into bearing retaining ring on axle. DO NOT drill into axle. Using a cold chisel, cut bearing retaining ring across drilled hole, and remove from axle shaft. Using a press and Bearing Remover (1130), remove bearing from axle shaft. Remove seal and retainer plate from axle shaft. Installation 1. Ensure axle shaft retaining plate is flat and not warped. Install retaining plate on axle shaft. Apply wheel bearing grease to axle shaft seal. Install seal on axle shaft. Grease bearing, and install on axle shaft with outer surface groove facing seal. 2. Using press and Bearing Installer (7913), press bearing onto axle shaft. Press NEW bearing retainer ring onto axle shaft. Install axle shaft in axle tube. Tighten NEW axle retainer plate nuts to specification. See TORQUE SPECIFICATIONS table. PINION SEAL & YOKE Removal

Related Content:

2005 chevy silverauto right front wheel bearing hub bearing nut tork setting, exploded view 1996 jeep grand cherokee exploded view of front suspension, how to remove right front axle 95 bronco, Silverado Rear Axle Seal Replacement, Meritor Axle Nut Torque Specs, Torque specs for 2008 prius axle nuts, 2002 ford expedition trailing arm torque specs, 2002 dodge dakota front differential diagram, estimate front axle seal escape, DIY LEXUS GX 470 AXLE REPLACE

2003 Ford F-Super Duty 250-550/ Excursion Differential Case and Ring Gear Removal And Installation manual

0

Filed Under (Ford Manuals) by admin on 07-02-2012

download
1. Remove the differential case. For additional information, refer to Differential Case in this section. 2. NOTE: The differential bearings need not be removed to overhaul the Ford limited slip differential. If bearing removal is required, for additional information, refer to Differential Case in this section. NOTE: The anti-lock speed sensor ring cannot be reused once removed. Remove the differential pinion shaft lock bolt and remove the differential pinion shaft. ? If required, remove the ring gear and anti-lock speed sensor ring. 3. NOTE: This tool does not have the 1/2-inch drive hole. Install the special tool in a suitable vise. 4. Install the differential case on the special tool 5. Install the special tool in the bottom side gear bore. ? Apply a small amount of grease to the centering hole of the special tool. 6. Install the nut in the upper differential side gear. Hold the nut in position while installing the hex screw. Tighten the hex-head screw until contact is made with the Step Plate 7. Insert a suitable dowel bar in the hole of the nut. Tighten the forcing screw to force the differential side gear away from the differential pinion gears. The dowel bar is used to keep the nut from turning when the forcing screw is tightened. 8. WARNING: Keep fingers/hands away from pinion gears when rotating the differential case with the differential rotating tool. NOTE: Differential pinion thrust washers cannot be removed independently of the differential pinion gears and so must be removed simultaneously with the differential pinion gears. Insert the special tool in the pinion shaft bore and turn the differential case to “walk” the differential pinion gears and differential pinion thrust washers out to the differential case windows. 9. Remove the differential pinion gears and differential pinion thrust washers. 10. Remove the differential side gears and differential clutch packs and tag them RIGHT and LEFT with the shim. CAUTION: When separating the clutch plates and clutch discs, note the sequence in which they are disassembled. They must be reassembled in the same sequence. CAUTION: Do not use acids or solvents when cleaning the differential clutch pack. Wipe components with a clean, lint-free cloth only. Separate the differential clutch discs and clutch plates for cleaning and inspection. Refer to the disassembled view of the limited slip differential case in the Description and Operation portion of this section.

Related Content:

2002 suburban front differential rebuild manual, 06 Z71 rear differential skematics, Rear differential dampener repair, rav4 differential, front differential fill plug 2004 buick rendezvous, 9 ford axle bearing installation diagram, differential unit disassembly procedure, buick rendezvous differential fluid, diassembly of differential unit, frontier rear diff position sensor

Toyota CT20 CT20 Type Dynamic and Carbon Seal Repair Parts & Service Kits

0

Filed Under (Toyota Manuals) by admin on 23-06-2011

download
All parts are available for purchase as individual components or in the following popular Repair Kits Key Part number Description Q ty in Turbo 1500 – 320 – 750 1500 – 320 – 751 1500 – 320 – 752 1500 – 320 – 753 1500 – 320 – 754 1500 – 320 – 760 8 1500-320-100 Journal Bearing 2 2 2 2 2 2 2 9 1500-320-290 Bearing Spacer 1 11 1500-320-320 Thrust Bearing 1 1 1 1 1 1 14 1500-320-160 Piston Ring Turbine 1 1 1 1 1 1 1 15 1500-320-170 Piston Ring Compressor 1 1 1 19 1500-320-200 Thrust Collar 1 1 1 1 1 21 1500-320-220 Thrust Spacer Carbon 1 1 1 1 22 1500-320-221 Thrust Flinger Dynamic 1 1 24 1500-326-145 Seal Plate Retaining Ring 1 28 1500-320-310 Oil Deflector 1 29 1500-320-150 O Ring (Seal Plate) 1 1 1 1 1 1 1 30 1500-320-155 O Ring (CT20 C/Cover) 1 1 1 1 1 1 1 30 1500-320-156 O Ring (CT20 C/Cover) 1 1 1 33 1500-320-300 Seal Plate Assy Carbon 6.1mm Depth 1 1 1 1 34 1500-320-301 Seal Plate Assy Dynamic 1 1 34 1500-320-302 Seal Plate Assy Carbon 7.57mm Depth (for turbo 54030) 1 1 43 1500-320-351 Shaft Nut LHT 1 1 1 1 1 1 1 – 1500-320-790 Gasket CT20 Oil Inlet / outlet 1 1 1 1 1 1 1 – 1500-320-791 Gasket CT20 Water Inlet / Outlet 2 2 2 2 2 2 2 Description of Repair Kits available 1500-320-750 Repair Kit (Minor) CT20 Dynamic 1500-320-751 Repair Kit (Minor) CT20 Carbon Seal 1500-320-752 Repair Kit (Major) CT20 Carbon Seal 1500-320-753 Repair Kit (Major) CT20 Dynamic 1500-320-754 Repair Kit (Major) CT20 Carbon Seal (54030 Only) 1500-320-760 Repair Kit CT20 (Carbon Seal – No thrust bearing Notes: 1) CT20 and CT26 repair kits are identical except for the Comp Cover O-ring – USE 1500-326-754 kit to repair both CT20/CT26 dynamic models from one kit. 2) For Pre 1990 CT20 Landcruiser 2.4L (17201-54030), the seal plate flange is deeper ( Part No. 1500-320- 302 ) and the O-ring groove is Ø114mm in the comp cover rather than Bearing housing. Use kit 1500-320- 754. Version 7.0 CT20 Type Oversize Repair Parts Available Journal Bearings CT20/26 Standard Standard 1500-320-100 + 0.005″ – 0.005″ 1500-320-110 + 0.005″ Standard 1500-320-114 Standard – 0.005″ 1500-320-117 + 0.010″ – 0.010″ 1500-320-120 + 0.010″ Standard 1500-320-124 Standard – 0.010″ 1500-320-127 + 0.005″ – 0.010″ 1500-320-130 Piston Rings CT20/26 Turbine Compressor OD Width Standard Standard 1500-320-160 + 0.010″ Standard 1500-320-180 Standard + 0.010″ 1500-320-181 + 0.010″ + 0.010″ 1500-320-182 Standard Standard

Related Content:

1998 chevy silverado manual, 1998 chevy 1500 heater case, 90 ford aerostar repair manual, Replacing the reverse band Dodge 1500, 2010 silverado 1500 4 3 liter canister vavle solenoid, repair manual for 1998 chevrolet 1500, ax12-1500 nut torque, downloadable schematic for 99 Chevy suburban evap system, parts manual for lazy boy reclin, Pcv valve 2005 gmc 1500

2006 Saturn ION L4-2.2L VIN F Window Regulator Replacement – Front Door (Power Regulator) removal and installation procedure

0

Filed Under (Saturn Manuals) by admin on 05-01-2012

download
Removal Procedure 1. Lower the window to the full down position. 2. Remove the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door ) . 3. Remove the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 4. Remove the water deflector in order to access the window regulator. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 5. Disengage the door glass to the regulator sash channel clips (2). Separate the door glass from the sash channel (1). 6. Push the window to the up position and tape in place. 7. Loosen the power window regulator bolts. Remove the rear regulator bolt. 8. Lift the window regulator, disengaging the loosened bolts from the door. 9. Disconnect the regulator electrical connector. 10. Remove the power window regulator from the door. Installation Procedure 1. Loosely install the four forward fasteners into the window regulator. 2. Position the power window regulator in the door. 3. Connect the door window regulator electrical connector. Notice: Refer to Fastener Notice in Cautions and Notices. 4. Install the power window regulator bolts. Tighten the regulator bolts to 10 N.m (89 lb in). 5. Remove the tape from the window. Push the window down to the regulator sash channel. 6. Slide the glass sash clips (2) into the window regulator sash channel (1). 7. Install the water deflector. Refer to Water Deflector Replacement – Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ComponentsWater Deflector Replacement – Front Door ) . 8. Install the radio speaker. Refer to Speaker Replacement – Front Door in Entertainment. 9. Install the door trim panel . Refer to Trim Panel Replacement – Side Front Door ( See: Body and FrameDoors, Hood and TrunkFront Door PanelService and RepairFront Door Panel ReplacementTrim Panel Replacement – Side Front Door

Related Content:

what does a fuel pressure regulator do on a 2003 gmc yukon, 2009 focus exterior door hand replacing, 2005 yukon xl blend door problems, volvo penta impeller replacement instructions, how to remove a 2009 chev avalanche door panel, How to replace a window regulator on 2002 LIncoln ls, how to remove 2008 chevy silverado back passenger window replacement, replace temperature door actuator 2005 chevy 2500hd truck, replace lh front door regulator on 2002 explorer, remove alternator malibu 2010

2003 Ford F-Super Duty 250-550/ Excursion Rear Drive Axle/Differential/ Ford 10.50-Inch Ring Gear Installation Manual

0

Filed Under (Ford Manuals) by admin on 30-06-2012

download
1. Remove the differential case. For additional information, refer to Differential Case in this section. 2. NOTE: The differential bearings need not be removed to overhaul the Ford limited slip differential. If bearing removal is required, for additional information, refer to Differential Case in this section. NOTE: The anti-lock speed sensor ring cannot be reused once removed. Remove the differential pinion shaft lock bolt and remove the differential pinion shaft. ? If required, remove the ring gear and anti-lock speed sensor ring. 3. NOTE: This tool does not have the 1/2-inch drive hole. Install the special tool in a suitable vise. 2003 F-Super Duty 250-550/Excursion Workshop Manual 5. Install the special tool in the bottom side gear bore. ? Apply a small amount of grease to the centering hole of the special tool. 6. Install the nut in the upper differential side gear. Hold the nut in position while installing the hex screw. Tighten the hex-head screw until contact is made with the Step Plat 2003 F-Super Duty 250-550/Excursion Workshop Manual 7. Insert a suitable dowel bar in the hole of the nut. Tighten the forcing screw to force the differential side gear away from the differential pinion gears. The dowel bar is used to keep the nut from turning when the forcing screw is tightened. NOTE: Differential pinion thrust washers cannot be removed independently of the differential pinion gears and so must be removed simultaneously with the differential pinion gears. Insert the special tool in the pinion shaft bore and turn the differential case to “walk” the differential pinion gears and differential pinion thrust washers out to the differential case windows. 9. Remove the differential pinion gears and differential pinion thrust washers. 10. Remove the differential side gears and differential clutch packs and tag them RIGHT and LEFT with the shim

Related Content:

ford e450 super duty manual, Sub Zero 550 Troubleshooting Guide, Ford 550 Backhoe Manual

1997 Ford Aerostar/ Ranger Wheel Grease Seal and Bearing Front Replacement and Repacking

0

Filed Under (Ford Manuals) by admin on 20-11-2011

download
Disassembly 1. Raise the vehicle and install Rotunda Car/Truck Stands 077-00018 or equivalent. 2. Remove the wheel and tire assembly. 3. Remove the retainer washers and remove the hub assembly. Refer to Manual Locking or Automatic Locking Hubs under Front Wheel Bearing Adjustment in this section for removal. 4. Remove the disc brake caliper (2B120) as described in Section 06-03 . 5. Remove the hub and rotor. Remove the outer wheel bearing cone. 6. Remove the wheel hub grease seal (1190) from the rotor with Seal Remover TOOL-1175-AC or equivalent and Impact Slide Hammer T50T-100-A. Discard wheel hub grease seal and replace upon assembly. 7. Remove excluder seal. 8. Remove the inner wheel bearing. 9. NOTE: If new wheel bearing cups are installed, install new cone and roller assemblies. Inspect the wheel bearing cups for pits or cracks. If necessary, remove them with Internal Puller D80L-943-A or equivalent and Impact Slide Hammer T50T-100- A. Assembly 1. Lubricate the wheel bearings with High Temperature Constant Velocity Grease E43Z-19590-A or equivalent meeting Ford specification ESP-M1C207-A. Clean all grease from the hub. Pack the cones and rollers. If a bearing packer is not available, work as much lubricant as possible between the rollers and the cages. 2. If wheel bearing cups are to be installed, position wheel bearing cups in rotor and drive in place with Bearing Cup Replacer T80T-4000-P and Driver Handle T80T-4000-W. 3. Position excluder seal on spindle and drive into position using Spindle Seal Replacer T95T-3132-D. 4. Position the inner wheel bearing in the inner wheel bearing cup in the rotor. Install the wheel hub grease seal by driving in place with Seal Replacer T80T-4000-T and Driver Handle T80T-4000-W. 5. Carefully install the rotor onto the front wheel spindle (3105). Refer to Section 06-03 . 6. Install outer wheel bearing into rotor. 7. Refer to Automatic Locking Hubs under Front Wheel Bearing Adjustment in this section for remainder of installation

Related Content:

F550 wheel bearing torque, is the rear wheel bearing wet f350 97, replacing rear wheel bearing on 2006 escape, 2009 BUICL ENCLAVE WHEEL BEARING TORQUE, tools needed to change hub and bearing assembly on 2002 tahoe, f53 wheel bearing seal change, Toyota Tacoma Bearing Hub Assembly 2008 inside details, wheel bearing 2000 dodge dakota, isuzu npr wheel bearing installation, malibu direct drive ahaft greasing

HONDA Front Seat Belt Replacement Warranty Policy

0

Filed Under (Honda Manuals) by admin on 24-11-2011

download
CUSTOMER INFORMATION : The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your car. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this bulletin applies to your car, or that your car has the condition described. To determine whether this information applies, contact an authorized Honda automobile dealer. ? 1996 American Honda Motor Co., Inc. – All Rights Reserved . ATB 14788-17665 (9601) 1 of 2 JAN 22, 1996 92-012 BODY ALL 1986 and later Applicable To Model File U nder Issu e D ate Bulletin N o. Service Bulletin Front Seat Belt Replacement Warranty Policy (Supersedes 92-012, dated March 13, 1992) Warranty policy for front seat belt replacement is to replace either the belt/retractor mechanism or the buckle when either does not work properly. Warranty covers the replacement of the failed half of a belt, not the entire assembly (see PARTS INFORMATION ). NOTE: For 1970 through 1985 models, seat belts are replaced as a complete assembly under a separate warranty policy. COMPONENT REPLACEMENT Front seat belts are made by several suppliers, and some are sold as individual components (two separate halves); they are not stocked as a complete set. Therefore, whenever you replace a belt, make sure the new belt half is the same type and from the same manufacturer as the original – otherwise, the belt may not buckle properly. To determine the manufacturer and type (or “model”) of the belt, look for the white tag on the original belt in the car. The tag is on the retractor side of the belt (visible at the lower attachment point), or on the belt if you pull the belt all the way out. From the tag, mark down the manufacturer’s name (either Nippon Seiko K.K. or Takata), the belt “model” number and the date of manufacture. If the tag is missing or illegible, look on the buckle component for the name Nippon Seiko K.K. or the stylized “T” mark () for Takata. NOTE: Some belts may have NSK Warner K.K. as the manufacturer’s name. Use Nippon Seiko K.K. belts as the replacement. Take the information to your Parts Department to order the proper replacement belt. NOTE: For more information on seat belts and seat belt related items read: -Twisted Seat Belt (ServiceNews, July ’85) -Seat Belt Testing and Repair (Service Bulletin 86-014, August ’86) -Automatic Seat Belt Troubleshooting (ServiceNews, May ’89) -Lap Belt Retracts Slowly (Service Bulletins 90-003, January ’90 and 90-012, April ’90) -Torn Seal on Seat Belt Track (Service Bulletin 91-004, March ’91) -Slow to Retract Seat Belt, Cleaning the Guide Ring (ServiceNews, April ’91) -Accord Shoulder Belt System Wire Colors (ServiceNews, May ’91) -Seat Belt Slow to Retract (Service Bulletin 91-030, December ’91) Refer to your Service Bulletin Index and the ServiceNews Index for model specific information. Most repairs do not require seat belt component replacement. PARTS INFORMATION For front seat belt replacement ordering information and availability, contact your parts center.

Related Content:

1986 chevy c10 new belt, installing new rotors on a 1992 ford f250 4wheel drive, volvo 850 repair seat belt tensioner manual download, 2004 chevy malubu surpupten belt replacement on a 2 2 liter on you tube, 2002 chevy malibu passlock gm bulletin, sun visor repairs 2013 honda accord, snugtop glass button bolt, replace sun visor 09 honda accors, repairing seat belt in dodge dakota, 1990 HONDA CIVIC SEATBELT FUSE BLOCK

Related Content:

guide differential f53 1997, replacing 94 camaro rack and pinion, how to repair noise driveshaft in a ford expedicion 2001, cummins n14 accessory drive torque specs, cost to replace a rack and pinion on 2002 suburban, 2004 ford f150 yoke, meritor pinion seal installer, mercedes exhaust pipe torque spec, mercury drive shaft socket, how to change rack and pinion 05trailblazer