Skip to content

how to replace radiator on 2001 buick lesabre

You search PDF repair manual about how to replace radiator on 2001 buick lesabre, if there are search results will appear below. If search results do not exist, please search by others keyword.

1995-1999 Buick Riviera Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly)

download
1. Verify that the power steering pump reservoir is full. 2. Verify that the accessory drive belt is in good condition and that the pulleys are not bent or damaged. 3. Verify proper belt tension and operation of the belt tensioner. 4. Check for power steering hose ground out conditions. 5. Check for good engine idle and correct engine RPM. 6. Check to see that the rear transaxle mount does not have a plastic assembly aid installed which is used Subject: Steering Vibration/Shudder/Moan During Parking Maneuvers on Dry Pavement (Install Power Steering Pressure (Inlet) and/or Return (Outlet) Hose Assembly) Models: 1995-99 Buick Riviera 1997-2001 Buick Park Avenue, Ultra 2000-2001 Buick LeSabre 2000-2001 Pontiac Bonneville • 1995-98 Buick Riviera • 1997-98 Buick Park Avenue and Ultra • 1999 Buick Riviera • 1999-2001 Buick Park Avenue and Ultra • 2000-2001 Buick LeSabre • 2000-2001 Pontiac Bonneville • If fluid level is low, fill and check for leaks. • If power steering system has air in the system, perform the “Bleeding Air from Power Steering System” procedure as described in the Power Steering System sub-section of the Service Manual. Important: When performing the “Bleeding Air from Power Steering System” procedure, it is important that the front of the vehicle is supported by the lower control arms. If the vehicle is not supported by the lower control arms, the procedure may cause the strut bushing to dislocate and cause new concern. for assembly purposes. If the assembly aid is installed, remove the assembly aid and install the rear transaxle mount. 7. With the vehicle on dry pavement, maneuver the vehicle in parking positions. If the steering vibrates/shudders or moans in this test, replace the power steering pressure hose and/or the harmonic balancer. Important: A defective harmonic balancer on the 1995 Buick Riviera can influence steering vibrations after power steering hose installation. Important: When installing the pressure hose on the 1995 Buick Riviera, pull down on the pressure hose at the rear of the engine or bend the hose to allow clearance between the hose and the front of the dash. Power Steering Pressure (Inlet) Hose Replacement Procedure For 1995-1998 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the power steering gear assembly heat shield (1). 4. Disconnect the power steering pressure hose from the power steering pump assembly (4). 5. Remove the bolt/screws from the retaining clips (3). 6. Disconnect the power steering pressure hose from the power steering gear assembly (2). 7. Remove the power steering pressure hose assembly from the vehicle. 8. Install the power steering pressure hose assembly to the vehicle. 9. Connect the power steering pressure hose to the power steering pump assembly (4). 10. Connect the power steering pressure hose to the power steering gear assembly (2). Tighten Tighten the power steering pressure hose to the steering gear to 27 N·m (20 lb ft). 11. Install the bolt/screws to the retaining clips (3). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). 12. Install the power steering gear assembly heat shield (1). 13. Lower the vehicle. 14. Fill and bleed the power steering system using, J 43485. Refer to Corporate Bulletin Number 83-32-09, dated November, 1998. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure For 1999-2001 Vehicles: 1. Raise and suitably support the vehicle. Refer to Vehicle Lifting and Jacking in the General Information section of the Service Manual. 2. Drain the power steering fluid. Refer to Draining the Power Steering System in the Power Steering section of the Service Manual. 3. Remove the LH front wheel/tire assembly. 4. Remove the LH lower splash shield. 5. Remove the lower radiator air deflector (engine splash shield, if installed.

2004 Buick LeSabre Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Service Manual

download
Correction 1. Visually inspect the tires and the wheels. Inspect for evidence of the following conditions and correct as necessary: 2. Set the tire pressure to 30 psi (205 kPa) COLD. Subject: Shake/Vibration in Steering Wheel, Floor, Seat at Highway Speeds on Smooth Roads (Diagnose/Balance Tires/Wheels) Models: 1998-2005 Buick Park Avenue, Park Avenue Ultra 2000-2005 Buick LeSabre 1998-2004 Cadillac Seville (SLS, STS) 2000-2005 Cadillac DeVille (DTS only) 2001-2003 Oldsmobile Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) • Missing balance weights • Bent rim flange • Irregular tire wear • Incomplete bead seating • Tire irregularities • Mud/ice build-up in wheel • Stones in the tire tread © 2009 General Motors Corporation. All rights reserved 3. Road test the vehicle with the Electronic Vibration Analyzer (EVA) essential tool for a sufficient distance on a known, smooth road surface to duplicate the condition. Record the Hertz (Hz) reading as displayed by the EVA onto the tire data worksheet found at the end of this bulletin. This should be done after a tire break-in period of at least 10 miles (16 km) at 45 mph (72 km/h) or greater, in order to eliminate any possible tire flat-spotting. 4. If the road test indicates a shake/vibration still exists, check the imbalance of each tire/wheel assembly on a known, calibrated, off-car dynamic balancer. If any assembly calls for more than ¼ ounce on either rim flange, remove all balance weights and rebalance to as close to zero as possible. Important: Some GM dealers may have a Hunter GSP9700 Road Force Balancer, or a Coats XR1850 Runout Balancer. Either will simplify Step 5 by not requiring dial indicators. If a Hunter GSP9700 machine is available, it may also be used to measure the radial force of the tire/wheel assembly. A guideline here is 18 lbs or less. 5. While on the balancer, measure wheel runout. If radial or lateral runout exceeds .020 in (0.50 mm) for aluminum wheels (.030 in (0.76 mm) for steel wheels), replace the wheel. 6. After confirming wheel balance and wheel runout, if any changes were made, road test the vehicle again. 7. If the smooth road shake/vibration still exists: Important: THE CONTROL ARMS SHOULD ONLY BE INSTALLED ON VEHICLES IF, AFTER THE TIRE AND WHEEL DIAGNOSIS AND REPAIRS HAVE BEEN PERFORMED, THE VIBRATION CONDITION STILL EXISTS. 8. Replace both lower control arms on vehicles built prior to the following VIN breakpoints. On Aurora, Bonneville, DeVille, Park Avenue, Park Avenue Ultra and Seville models, a newly developed hydro-bushing lower control arm with improved damping characteristics has been released. This control arm is not used on the LeSabre. The new lower control arms may provide an incremental improvement to the vehicle ride. Customers who have become “tuned in” to the shake condition may still feel some shake in the vehicle after the new lower control arms are installed. Refer to Lower Control Arm Replacement in SI (refer to the Parts Information table below for SI document ID numbers) . Important: The completed worksheet must be attached to the hard copy of the repair order. • If a Hunter GSP9700 Road Force/Balancing machine is used, record radial force variation (RFV) on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies read more than 18 lbs, match mount the tire to the wheel to get below 18 lbs. Readings of 12 lbs or less are preferable for sensitive customers. • If a Coats XR1850 Runout/Balancing Machine is used, record radial runout of the tire/wheel assemblies on the worksheet at the end of this bulletin. If one or more of the tire/wheel assemblies are more than .040, match mount the tire to the wheel to get below .040. Readings of .030 inch or less are preferable for sensitive customers. • If the RFV or runout cannot be reduced to an acceptable level, replace the affected tire(s) under the guidelines of the GM Tire Warranty. • The screened tire program is only available for the General branded tires used on the Buick LeSabre. Complete the tire request form at the end of this bulletin and fax to Continental/General. • Road test the vehicle to ensure the shake/vibration has been eliminated

4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

download
2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission this service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, four other gaskets not included in this service kit will also be needed to complete the repair, a Control Valve Body Cover (Side Cover) Gasket (54), a Control Valve Body Cover (Side Cover) Inner Gasket (59), a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering service kit P/Ns 24206959 and 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to- Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve Assemblies (315A, 315B).

2004 Chevrolet TrailBlazer Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Repair Manual

download
This bulletin is being revised to add model years and provide important repair information. Please discard Corporate Bulletin Number 04-08-49-015 (Section 08 — Body and Accessories). Condition Some customers may comment on a noise coming from the instrument panel cluster (IPC) while driving or on initial start-up. Instrument clusters may contain stepper motor gages that can make noise during the following conditions: Subject: Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Models: 2003-2005 Buick LeSabre 2003-2007 Buick Rendezvous 2004-2005 Buick Rainier 2003-2006 Cadillac Escalade, Escalade ESV, Escalade EXT 2003-2005 Chevrolet Cavalier, Impala, Monte Carlo 2003-2006 Chevrolet Avalanche, Suburban, Tahoe, TrailBlazer EXT 2003-2007 Chevrolet Silverado Classic, TrailBlazer 2003-2007 Chevrolet Kodiak Models 2004-2006 Chevrolet SSR 2003-2006 GMC Envoy XL, Yukon, Yukon XL 2004-2005 GMC Envoy XUV 2004-2007 GMC Envoy 2003-2007 GMC Sierra Classic 2003-2004 Oldsmobile Bravada 2003-2005 Pontiac Aztek, Bonneville, Sunfire 2003-2005 HUMMER H2 Attention: Appropriate repair is based on vehicle build date. Use GMVIS to determine the vehicle build date. • Initial startup (gages zero/reset)

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt