Skip to content

how to replace remote oil lines on chevrolet s10

You search PDF repair manual about how to replace remote oil lines on chevrolet s10, if there are search results will appear below. If search results do not exist, please search by others keyword.

1998 Chevrolet Blazer Engine Oil Cooler Hose/ Pipe Removal And Installation Manual

download
Removal Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engine oil cooler line quick connectors at the radiator engine oil cooler inlet and outlet. Follow the next two steps for the proper retaining ring removal procedure. 5. Using a bent-tip screwdriver or equivalent, pull on one of the open ends of the retaining ring in order to rotate the retaining ring. 6. Rotate the retaining ring around the quick connector until the retaining ring is out of position and can be completely removed. Discard the retaining rings. 7. Remove the engine oil cooler lines from the quick connectors at the radiator engine oil cooler inlet and outlet. Pull the lines straight out from the connectors. 8. Remove the remote engine oil filter lines support clamp bolt. Important: Have a drain pan ready for the engine oil to drain into. 9. Remove the bolt attaching the remote engine oil filter lines to the remote (frame mounted) engine oil filter adapter. 10. Hold the remote engine oil filter lines below the remote engine oil filter lines (engine mounted) adapter to drain the engine oil. 11. Remove and discard the seals. 12. Remove the bolt attaching the remote engine oil filter lines to the remote engine oil filter lines (engine mounted) adapter. 13. Remove and discard the seals. 14. Clean all of the components in a suitable solvent, and dry them with compressed air. 15. Inspect the fittings, the connectors, the cooler lines, the cooler, the filter lines, and the remote filter adapter for damage, distortion, or restriction. Replace parts as necessary. 16. Flush the engine oil cooler, the engine oil cooler lines, the remote engine oil filter adapter, and the remote engine oil filter lines with the same type of engine oil normally circulating through the engine. Installation Procedure

2004 Chevrolet TrailBlazer Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Repair Manual

download
This bulletin is being revised to add model years and provide important repair information. Please discard Corporate Bulletin Number 04-08-49-015 (Section 08 — Body and Accessories). Condition Some customers may comment on a noise coming from the instrument panel cluster (IPC) while driving or on initial start-up. Instrument clusters may contain stepper motor gages that can make noise during the following conditions: Subject: Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Models: 2003-2005 Buick LeSabre 2003-2007 Buick Rendezvous 2004-2005 Buick Rainier 2003-2006 Cadillac Escalade, Escalade ESV, Escalade EXT 2003-2005 Chevrolet Cavalier, Impala, Monte Carlo 2003-2006 Chevrolet Avalanche, Suburban, Tahoe, TrailBlazer EXT 2003-2007 Chevrolet Silverado Classic, TrailBlazer 2003-2007 Chevrolet Kodiak Models 2004-2006 Chevrolet SSR 2003-2006 GMC Envoy XL, Yukon, Yukon XL 2004-2005 GMC Envoy XUV 2004-2007 GMC Envoy 2003-2007 GMC Sierra Classic 2003-2004 Oldsmobile Bravada 2003-2005 Pontiac Aztek, Bonneville, Sunfire 2003-2005 HUMMER H2 Attention: Appropriate repair is based on vehicle build date. Use GMVIS to determine the vehicle build date. • Initial startup (gages zero/reset)

2004-2006 Chevrolet Malibu, Malibu Maxx Loss of Power Steering Assist, Power Steering Warning Message Displayed in DIC, IPC/Radio Displays Erratic, DTC C0900, B1325 Set (Replace Ignition Coil/Module Assembly and Add Ground Strap)

download
Correction Replace the ignition coil/module assembly and add ground strap following the procedure below. 1. Disconnect the ignition coil electrical connector. 2. Disconnect the left side spark plug wires from the ignition coil. 3. Disconnect the right side spark plug wires from the ignition coil. 4. Remove the four bolts attaching the ignition coil to its mounting bracket and remove the ignition coil. 5. Remove the ignition coil from the mounting bracket. 6. Loosen the two lower ignition coil mounting bracket nuts. 7. Remove the two upper ignition coil mounting bracket bolts and discard. Subject: Loss of Power Steering Assist, Power Steering Warning Message Displayed in DIC, IPC/Radio Displays Erratic, DTC C0900, B1325 Set (Replace Ignition Coil/Module Assembly and Add Ground Strap) Models: 2004-2006 Chevrolet Malibu, Malibu Maxx with 3.5L Engine (VINs 8, N — RPOs LX9, LZ4) 8. Install the ground strap (1), P/N 12581176, to the upper left side of the bracket as shown between the coil bracket and intake. Install the new bracket bolt, P/N 11570082, (do not tighten at this time). Prior to installing the ground strap, remove the captured nut and washers. They are not needed (simply pound them out with a hammer on a vise). 9. Install the washer (2), P/N 02436162, to the upper right side of the bracket between the coil bracket and intake. Install the new bracket bolt, P/N 11570082, (do not tighten at this time). Tighten Tighten all the ignition coil bracket bolts and nuts to 25 N·m (15 lb ft). 10. Install the new ignition coil to the mounting bracket. 11. Install the other end of the ground strap to the coil as shown and secure using a new bolt, P/N 11588715. 12. Install the other three ignition coil bolts. Tighten Tighten the bolts to 10 N·m (89 lb in). 13. Connect the right side spark plug wires to the ignition coil. 14. Connect the left side spark plug wires to the ignition coil. 15. Connect the ignition coil electrical connector

Remote Keyless Entry (RKE) Inoperative, Poor Range, Tire Pressure Monitor (TPM) Message Displayed, Remote Vehicle Start (RVS) (Replace/Reprogram RCDLR, Replace Antenna and Transmitters)

download
Models: 2006-2007 Buick Lucerne 2006-2007 Cadillac DTS 2006-2007 Chevrolet Impala, Monte Carlo 1. Replace the RCDLR module and the RCDLR antenna using the following procedure: Impala / Monte Carlo DTS • DTS / Lucerne: 5/1/07 • Impala / Monte Carle: 3/1/07 • The 2006 and 2007 Impala LS without AP8 does not have a coax antenna. • The 2006 and 2007 Lucerne without AP3 or AP8 does not have a coax antenna. 1.1. Remove the driver’s side “A” pillar molding and I/P closeout panel. 1.2. Unplug the speaker. 1.3. To expose the RCDLR antenna, partially remove the driver’s side upper I/P closeout panel (near windshield). 1.4. Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the “A” pillar. 1.5. Cut the old RCDLR antenna wire a minimum of 152 mm (6 in) from the button (connecting to the windshield), leaving that portion of the old RCDLR antenna connected to the windshield. 1.6. Remove the I/P carrier bolt and remove the old RCDLR antenna. 1.7. Remove the RCDLR module. 1.8. Install the new RCDLR module. 1.9. Lay in the new RCDLR antenna and reinstall the carrier bolt. 1.10. Connect the new antenna to the RCDLR antenna module. 1.11. Clip the new RCDLR antenna into place using the existing holes on the “A” pillar. 1.12. Reinstall the I/P close-out panel. 1.13. Reconnect the speaker wire. Important: Be sure that the end of the old RCDLR antenna is tucked behind the “A” pillar molding. The button on the windshield is no longer functional, however leaving the cover on the button will provide a cleaner look to the vehicle. 1.14. Reinstall the “A” pillar molding and I/P side closeout panel. 1.1. Remove the rear seat cushion. 1.2. Remove the rear seat back.

2002 Chevrolet Impala Radiator Air Baffle and Deflector Replacement Manual

download
Radiator Air Baffle and Deflector Replacement – Upper Removal Procedure 1. Remove the radiator air baffle retainers. 2. Tilt the rear of air baffle upward slightly. Slide the air baffle rearward in order to disengage the upper and lower clips of the air baffle from the fascia support. 3. Remove the radiator air baffle. Installation Procedure 2002 Chevrolet Impala 1. Position the radiator air baffle to the vehicle. Tilt the rear of the air baffle upward slightly. Position the upper clip of the air baffle to the lower edge of the front fascia support C-channel. 2. Slide the baffle towards the front of the vehicle in order to completely engage the upper and lower clips of the baffle onto the fascia support. 3. Align the tabs at the rear of the air baffle to the openings in the upper radiator support. 4. Install the radiator air baffle retainers.