how to replace the exhaust manifold on a 2004 trailblazer

You search PDF repair manual about how to replace the exhaust manifold on a 2004 trailblazer, if there are search results will appear below. If search results do not exist, please search by others keyword.



  how to replace the exhaust manifold on a 2004 trailblazer Direct Download speed 5432 Kb/s

  how to replace the exhaust manifold on a 2004 trailblazer Full Version speed 8172 Kb/s



1996 Ford Truck E 350 Exhaust Manifold – Exhaust Leaks Service Manual

0

Filed Under (Ford Manuals) by admin on 08-02-2012

download
SERVICE PROCEDURE NOTE IF THE MANIFOLD IS TO BE RESURFACED, THE BOLTS MUST BE SHORTENED TO ACCOMMODATE THE EXHAUST MANIFOLD . THE BOLTS SHOULD HAVE THE LEADING “DOG POINT” REMOVED TO PREVENT BOTTOMING INTO THE HOLE. NOTE THERE SHOULD NOT BE ANY TYPE OF GASKET USED BETWEEN THE EXHAUST MANIFOLD AND THE CYLINDER HEAD. Parts Block OTHER APPLICABLE ARTICLES: NONE SUPERSEDES: 97-26-23 WARRANTY STATUS: Eligible Under The Provisions Of Bumper To Bumper 1. If an exhaust leak exists at the exhaust manifold due to a reduction in bolt torque, remove the manifold bolts and the exhaust manifold and check the overall flatness of the manifold. The manifold should not exceed 0.25 mm (0.010″) out- of-flat. Refer to the appropriate model/year Service Manual for manifold removal procedures. 2. If the vehicle is covered under the emissions warranty period, replace the manifold if it is out-of-flat. If the vehicle is out of the emissions warranty period, resurface the exhaust manifold 3. Install the manifold using new mounting hardware, but DO NOT USE WASHERS TO INSTALL THE MANIFOLD. Torque the bolts to 34-47 N.m (25- 35 lb-ft). 4. Check all exhaust system fittings loosened during repair for adequate tightness and allow engine to warm up. Recheck exhaust system for leaks and repair as required.

Related Content:

ford 5 4L water jacket leak spark plug hole intake gasket, 2001 ford excursion water leak on back of motor, metal mesh hanging loose under escort zx2, volvo d12 exhaust manifold bolt torque, replace a front exhaust manifold 2004 ford escape 24 valve, isuzu npr 5 7 water pump bolt torque, schematic of a 2005 chrysler exhaust system, volvo penta 125 exhaust manifold bolt torques, what parts are required to replace the exhaust from the manifold on back for a 1990 ford f150, intake manifold leak sound

2000 Ford Windstar Intake Manifold-Lower Removal And installation manual

0

Filed Under (Ford Manuals) by admin on 25-06-2012

download
Intake Manifold—Lower Removal 1. Partially drain the cooling system. For additional information, refer to Section 303-03 . 2. Remove the upper intake manifold (9424). For additional information, refer to Intake Manifold—Upper in this section. 3. Remove the fuel supply manifold (9F792). For additional information, refer to Section 303-04B . 4. Disconnect the EGR vacuum tube (9E498). 5. Disconnect the EGR-to-exhaust manifold tube (9D477). * Loosen the nut. 6. Disconnect the upper radiator hose (8260). * Reposition the clamp. * Disconnect the hose. 7. Disconnect the heater hose (18472). * Compress the fitting * Disconnect the hose. 8. Disconnect the intake manifold runner control (IMRC). 9. Position the water bypass tube (8555) aside. 1. Remove the bolts. 2. Position the tube aside. 10. NOTE: Note the location of the six long bolts. Remove the lower intake manifold (9J447). 1. Remove the bolts. 2. Remove the intake manifold. 11. Remove the intake manifold runner control (IMRC) if necessary. For additional information, refer to Section 303-14 . 12. Remove and discard the lower intake manifold sealing components. Installation 1. Refer to the illustration for intake manifold sealing component locations. 2. Install the lower intake manifold front and rear end seals. 1. Apply a bead of sealant to the intake manifold front and rear end seal mounting points as indicated. * Use Silicone Gasket and Sealant F7AZ-19554-EA or equivalent meeting Ford specification WSE-M4G323-A4. 3. Install the lower intake manifold front and rear end seals. 3. Install the intake manifold gaskets (9439). 4. Install the intake manifold runner control (IMRC) if required. For additional information, refer to Section 303-14 . 5. NOTE: The lower intake manifold must be installed within four minutes of applying sealant. Position the lower intake manifold. 1. Apply a bead of sealant to the lower intake manifold mounting at the points indicated. * Use Silicone Gasket and Sealant F7AZ-19554-EA or equivalent meeting Ford specification WSE-M4G323-A4. 3. Position the lower intake manifold.

Related Content:

s10 2 2 upper intake manifold removal, 2000 bmw528i how to remowe intake manifold, 1997 FORD 4 2 INTAKE MANIFOLD RUNNER CONTROL VALVE DIAGRAM, how remove intake manifold on 1998 Toyota sienna, picture of bolt pattern of intake manifold on 2006 h3 hummer, torque specs 02 grand prix intake bolt, removing lower intake manifold 1994 pontiac grand prix, manifold replacement on 5 7 volvo penta on you tube, intake manifold torque on a 1999 bmw 528i, locate intake manifold runner control vacuum hose for 2005 ford focus

4.6L Mustang Bassani Mid Length Headers INSTALLATION INSTRUCTIONS

0

Filed Under (Ford Manuals) by admin on 05-12-2011

download
INSTALLATION INSTRUCTIONS 1. Disconnect the battery. 2. Safely raise & support vehicle to a comfortable working height. (One jack stand at each corner of vehicle.) 3. Spray attaching hardware and base of o2 sensors with WD40 or similar Lubricant. Remove 02 sensors from stock system. (Be careful not to damage or contaminate sensor). Stock gasket will be re-used upon assembly. 4. Remove both connector tubes between stock exhaust manifold and Bassani Modular X pipe. It may be necessary to loosen downstream clamps on the Bassani Modular X pipe. 5. Loosen EGR fitting on drivers side exhaust manifold. It will be necessary to remove nuts from the motor mounts at the K member to jack engine up. Motor mount heat shields have to be removed. 6. Loosen & remove both exhaust manifolds. 2 valve, stock manifold gaskets, depending on condition, may be re-used . Remove studs from both sides. Use supplied, and/or stock hardware. See note following #10. 7. Label wiring on starter and remove it. (Will be necessary for header installation) 8. You may also need to remove oil filter to ease installation and tightening on drivers’ side. 9. IMPORTANT! It will be necessary to unbolt steering shaft from rack. With a marker draw a straight line on shaft down to rack to index them both. Do not move front wheels or steering wheel. 10. It will be necessary to lift engine up enough to slide header tubes in and have access to install supplied header bolts. After loosening motor mount bolts, lifting engine (using a wooden block under oil pan) and removing motor mounts, one side at a time only, will ease installation. Removal of motor mounts is not mandatory. **Anti seize must be applied to all threads (header bolts and studs). It may be necessary to use a combination of header bolts and stock studs & nuts on certain tubes due to clearance between the tube and hardware. ie; stud nut or header bolt. The use of either is the installers preference. 11. Start on passenger side, with tube #1R. Push as far forward as possible to allow clearance for #2R. Once #2R is in position, install gaskets, and header bolts. When this is completed commence installation of #3R and #4R tubes following previous procedure. Leave bolts loose, DO NOT TIGHTEN UNTIL COLLECTOR IS INSTALLED. 12. When Collector R is ready for right side, place Bassani anti seize jet lube , on slip connectors to ease installation. When collector lines up with tab on header tube, fasten them together and tighten all header tubes. 13. When all hardware is properly tightened, lower engine, re-install motor mount hardware, starter and O2 sensors in collector. The use of Bassani anti seize Jet Lube is recommended on O2 sensor threads. Do not to contaminate O2 sensor bulb with lube. 14. Proceed to drivers’ side. Install #1L with gasket installed. Install supplied fasteners with Bassani anti seize jet lube on the threads. DO NOT TIGHTEN ALL THE WAY, leave semi loose. Install tube #3L, then #2L. You will need to experiment with pipes #2L and #3L. #2L will slip between #3L and #1L. Now install #4L, fasten and screw air fitting to tube #4L. Install Collector L . When collector tab lines up with header tab, tighten all hardware, and bolt on EGR, and any smog fittings. Lower engine and re-install motor mount hardware. Reconnect steering shaft using loctite 271 thread locker on bolt.

Related Content:

2002 chevy s10 exhaust flange seal, ebay ford 555 backhoe cheap service manual, replacing choke heater tube in 57 chevy exaust manifold

1997 Ford Explorer/ Mountaineer Intake Manifold Upper Repair Manual

0

Filed Under (Ford Manuals) by admin on 09-05-2012

download
Intake Manifold — Upper 1. Disconnect the battery ground cable. 2. Remove the air cleaner outlet tube; refer to Section 303-12 3. Disconnect the ignition coil electrical connector and the noise suppressor electrical connector. 4. Disconnect the idle air control (IAC) electrical connector. 5. Disconnect the EGR backpressure transducer electrical connector. 6. Disconnect the EVR solenoid electrical and vacuum connectors. 7. Disconnect the brake booster vacuum hose from the upper intake manifold. 8. Disconnect the vacuum connector from the upper intake manifold 9. Disconnect the vacuum connector from the fuel pressure regulator and remove the vacuum harness from the engine. 10. Disconnect the throttle position (TP) sensor electrical connector. 11. Disconnect the hoses from the EGR backpressure transducer ports. 12. Disconnect the six spark plug wires from the spark plugs. 13. Disconnect the spark plug wires from the seven retaining clips. 14. Remove the four ignition coil bolts and the ignition coil from the upper intake manifold. 15. Raise and support the vehicle; refer to Section 100-02 . 16. Access the LH exhaust manifold through the wheel well and disconnect the EGR inlet tube from the exhaust manifold (9430). 17. Lower the vehicle. 18. Disconnect the EGR inlet tube from the EGR valve and remove the EGR inlet tube. 19. Remove the EGR valve bolts and the EGR valve and gasket. 20. Remove the oil level indicator tube bracket nut and remove the oil level indicator tube (6754). 21. Remove the EGR outlet tube bracket stud bolt and remove the EGR outlet tube from the upper intake manifold. 22. Disconnect the accelerator cable assembly from the upper intake manifold bracket. 23. Remove the upper intake manifold nuts and remove the upper intake manifold and gasket. Installation 1. NOTE: Before installing the upper intake manifold, the EGR port must be clean and free of obstruction. Use combustion chamber cleaner and a suitable wire brush to remove carbon buildup from the EGR passages. Clean and inspect all surfaces. Install new seals and new gaskets. Use Metal Surface Cleaner F4AZ-19A536-RA or equivalent meeting Ford specification WSE-M5B392-A to clean the upper and lower intake manifold gasket surfaces. Position the upper intake manifold gasket on the fuel injection supply manifold. 2. Position the upper intake manifold and install the six nuts.

Related Content:

2000 mpv egr vacuum line, 1997 FORD EXPLORER VACUUM T SHAPPED HOSE, 2az fe intake manifold, 305 egr intke gasket, bad egr valve symptoms aveo chevrolet

4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal)4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Transmission Repair

0

Filed Under (More Manuals) by admin on 08-01-2012

download
Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: Subject: 4L60-E Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Models: 2004-2005 Buick Rainier 2003-2005 Chevrolet TrailBlazer Models 2003-2005 GMC Envoy Models 2003-2004 Oldsmobile Bravada 2005 Saab 9-7X with 4.2L In-Line 6 Cylinder Engine (VIN S — RPO LL8) • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. • Remove the surge tank cap and examine the coolant for signs of contamination with transmission fluid (the coolant will have a milky, not clear appearance). • If the coolant has a normal, clear appearance, the radiator should not be replaced. • The cooler can also be tested by following the Coolant System Leak Test procedure (SI Document ID# 877442). Do NOT replace a radiator without verifying that the transmission oil cooler is leaking. If water or coolant is found in the transmission, the following components MUST be replaced. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube. 3. Remove the filler tube nut (2) located on the right side of the engine. 4. Remove the filler tube from the vehicle. Tip It is necessary to remove the two A/C line (suction line / low side of muffler hose) retainers and reposition • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow .
the A/C line to allow proper clearance for installation of the new transmission fluid fill tube. 5. Remove the A/C line at the oil level indicator tube bracket nut. 6. Remove the A/C bracket bolt from the engine lift hook. 7. Reposition the A/C line upward. 8. Install the new transmission filler tube, P/N 15000220, into position but NOT into the transmission at this time. 9. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID# 744862). 10. Remove the two bolts securing the transmission heat shield to the transmission. 11. Remove the transmission heat shield from the transmission. 12. Remove the old filler tube seal from the transmission case. 13. Install a new seal, P/N 1259475 into the transmission case. 14. Position the new transmission filler tube into the transmission seal. 15. Install the transmission heat shield to the transmission. 16. Install the two bolts securing the transmission heat shield to the transmission. Tighten Tighten the bolts to 17 N·m (13 lb ft). 17. Lower the vehicle. 18. Install the nut securing the filler tube to the stud. Tighten Tighten the nut to 10 N·m (89 lb in). 19. Reposition the A/C line into place. 20. Install the A/C line bracket to the oil level indicator tube stud and secure the bracket with the nut. 21. Install the A/C line bracket to the engine lift bracket and secure the A/C bracket with the bolt

Related Content:

yhs-lavasoft, automatic transmission adjustments for 1997 yuko, 2003 trailblazer torque converter removal, 2005 explorer transmission exploded view, gm 4l60e band adjustment screws, 2011 crv engine whine, how to check tranmission fluid on 2012 kia sedona, manual pdf transmicion automatica ram 2001, e4od repair manual download, 2008 impala 4t65e moves forward in nuetral

2004 Chevrolet TrailBlazer Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Repair Manual

0

Filed Under (Chevrolet Manuals) by admin on 18-02-2012

download
This bulletin is being revised to add model years and provide important repair information. Please discard Corporate Bulletin Number 04-08-49-015 (Section 08 — Body and Accessories). Condition Some customers may comment on a noise coming from the instrument panel cluster (IPC) while driving or on initial start-up. Instrument clusters may contain stepper motor gages that can make noise during the following conditions: Subject: Noise Coming From Instrument Panel Cluster (Replace Instrument Panel Cluster (IPC)) Models: 2003-2005 Buick LeSabre 2003-2007 Buick Rendezvous 2004-2005 Buick Rainier 2003-2006 Cadillac Escalade, Escalade ESV, Escalade EXT 2003-2005 Chevrolet Cavalier, Impala, Monte Carlo 2003-2006 Chevrolet Avalanche, Suburban, Tahoe, TrailBlazer EXT 2003-2007 Chevrolet Silverado Classic, TrailBlazer 2003-2007 Chevrolet Kodiak Models 2004-2006 Chevrolet SSR 2003-2006 GMC Envoy XL, Yukon, Yukon XL 2004-2005 GMC Envoy XUV 2004-2007 GMC Envoy 2003-2007 GMC Sierra Classic 2003-2004 Oldsmobile Bravada 2003-2005 Pontiac Aztek, Bonneville, Sunfire 2003-2005 HUMMER H2 Attention: Appropriate repair is based on vehicle build date. Use GMVIS to determine the vehicle build date. • Initial startup (gages zero/reset)

Related Content:

service manual for 2004 audi a6 2 7t quattro, 2004 buick rendezvous repair manual, 2003 gmc sierra service repair manual, stepper motor for 2004 chevy trailblazer, repair manual mitsubishi diamante, 2005 gmc envoy repair manual, repairing center console for 2005 f150, 2005 gmc sierra 2500 hd replaceing instrument panel, ford 2004 6 0 manual, manual for 2008 pontiac g5

1996-2000 Chevrolet And GMC Suburban/ Pick-Up 2500/ 3500 Series TUBULAR EXHAUST SYSTEM INSTALLATION INSTRUCTION

0

Filed Under (Chevrolet Manuals) by admin on 29-12-2011

download
Disassembly – Left Side 1. Disconnect negative cable from battery. 2. Use penetrating oil on all nuts and bolts to be removed. This will prevent the possibility of broken or stripped nuts and bolts. 3. Remove air cleaner system (note position of line and hose connections). 4. Disconnect spark plug wires. 5. Disconnect temperature sensor wire. 6. Remove EGR fitting. 7. Remove bolts and exhaust manifold. Disassembly – Right Side 1. Remove air cleaner box. 2. Disconnect spark plug wires. 3. Remove dipstick and dipstick tube. 4. Remove bolts and exhaust manifold. 5. Clean exhaust flange surfaces on both cylinder heads at this time. DISASSEMBLY – CROSSOVER PIPE 1. Raise vehicle and support with jackstands. 2. Disconnect and remove 02 sensors (2), being careful not to rupture or destroy the unit. WARNING: Do not clean this unit in any cleaning solvent and do not damage wire. 3. Between left and right side of the catalytic converter is a 3-bolt flange with gasket. From the front face of flange, measure out 15″ towards front of truck and cut stock exhaust pipes. Remove exhaust pipes from vehicle. NOTE: Before cutting pipes, measure the height of the converter from the bottom of the floor board for when you install new exhaust pipes you can maintain same distance. •ASSEMBLY – LEFT SIDE 1. Install T.E.S. flange gasket and one 3/8″-16 x 1″ bolt, lock washer, and thick flat washer at rearmost bolt hole (leave bolt loose enough to accept T.E.S.). 2. Install left side T.E.S. manifold from bottom side 3. Install all bolts and washers and tighten. Use thick flat washers on slotted holes. 4. Reinstall spark plugs. 5. Replace original equipment spark plug ends on cylinders #3 and #5 with 60° connectors and boots provided in kit. 6. Re-connect spark plug wires on left side. 7. Re-install temperature sensor wire to temperature sensor. ASSEMBLY – RIGHT SIDE 1. Install T.E.S. flange gasket and one 3/8″-16 x 1″ bolt, lock washer and thick flat washers at rearmost bolt hole (leave bolt loose enough to accept T.E.S.). 2. Install right side T.E.S. manifold from top side. Now install dipstick tube. 3. Install remaining bolts and lock washers. 4. Align all parts and tighten all right side bolts at this time. 5. Replace original equipment spark plug ends on cylinders #4, #6 and #8 with 60° connectors and boots provided in kit. 6. Re-connect right side spark plug wires. 7. To prevent contact with the hot T.E.S. tubing, use nylon tie wrap (supplied) to secure the heater hose to the a.c. dryer. 8. Re-install air cleaner box. CROSSOVER PIPE ASSEMBLY 1. With catalytic converters in their natural position, install and bolt exhaust extension pipes to header collectors using 3/8″ – 16″ x 2 1/2″ hex bolts, 3/8″ flat washers, 3/8″ lock washers and 3/8 hex nuts. Use the 3″ donut provided in kit. 2. Check alignment of pipes to the catalytic converter, secure bolts. 3. With everything in place, tack weld exhaust pipes to catalytic assembly. 4. Unbolt whole exhaust assembly from vehicle and let it hang. Complete weld around pipes. 5. Bolt assembly back in vehicle and check for clearance. 6. Re-install 02 sensors. Use anti-seize on threads of sensor. Route wires clear of exhaust system. 7. Lower vehicle to ground

Related Content:

2005 taurus exhaust system diagram, 2 2 s10 exhaust flange bolts, diagram of an exhaust system on a 2003 gmc envoy, Diagram of a exhaust crossover pipe for a 95 Oldsmobile aurora, 04 pacifica parts diagram, pontiac sunfire gt exhaust system diagram, how tight should exhaust, gmc yukon exhaust manifold diagram, 454 exhaust donut installation, 2006 corvette mid pipe flange torque

2000-2004 Toyota Tundra 4.7L V-8 Two and Four Wheel Drive Installation Manual

0

Filed Under (Toyota Manuals) by admin on 27-03-2012

download
1. Place vehicle in a location where the floor is solid and flat, with adequate lighting. Do not attempt to work on a hot engine. Heat causes metal to expand and makes removal of fasteners difficult at best. Disconnect the battery cables from the battery. Raise the front of the vehicle to obtain adequate access to the bottom exhaust manifold flanges. Use large-base jack stands to support the vehicle. Do not rely on the jack! Block the tires to prevent the vehicle from rolling off the jack stands. 2. Spray WD-40 or some type of penetrating oil on all accessible fasteners and fittings before attempting to remove them. 3. From underneath the vehicle disconnect the exhaust system from the exhaust manifolds by unbolting the (3) bolts at the collectors. Then unbolt the driver side catalytic converter from the exhaust assembly and temporarily remove it from the vehicle. PASSENGER SIDE 4. On the passenger side remove the (4) bolts attaching the heat shields to the factory manifold. 5. Next, carefully unplug the O2 sensor from its harness. 6. Now remove the nuts attaching the factory manifold to the cylinder head. With the manifold out of the way remove the mounting studs from the cylinder head. 7. Using a small wire brush or similar instrument, clean any carbon deposits left on the head surface. Be careful not to gouge the aluminum head. 8. Transfer the O 2 sensor from the factory manifold to the new passenger side header. Apply a small amount of anti seize to the threads for the sensor before installing it in the new header. Use caution not to drop or damage the sensor, they are fragile. 9. Now you are going to install the new JBA Header, but first there is some preparation of the hardware required. Apply anti seize to the threads of the new fasteners. Install the new JBA Header using the supplied gasket and fasteners. Torque to 23 ft./lbs. DRIVER’S SIDE 10. Just like you did in step (4) remove the (4) bolts attaching the heat shields to the driver side factory mani- fold. 11. Next, carefully unplug the O2 sensor from its harness. Unbolt the dipstick bracket from the head and remove the dipstick tube. 12. Remove the nuts attaching the factory manifold to the cylinder head. With the manifold out of the way remove the mounting studs from the cylinder head. 13. Using a small wire brush or similar instrument, clean any carbon deposits left on the head surface. Be careful not to gouge the aluminum head. 14. Transfer the O 2 sensor from the factory manifold to the new driver side header. Apply a small amount of anti seize to the threads for the sensor before installing it in the new header. Use caution not to drop or damage the sensor, they are fragile. 15. As you did on the passenger side, prepare the hardware before installing the driver side header. Apply anti seize to the threads of the new fasteners. Install the new JBA Header using the supplied gasket and fasteners. Torque to 23 ft./lbs. Re-install the dipstick tube. 16. Install the driver side catalytic converter. 17. Connect the exhaust system to the new headers using hardware and gaskets supplied. Reconnect O2 sensors. 18. Check to insure adequate clearance between header and shifter cable (small cable that runs from firewall, to brace on fender well, to transmission) . More clearance can be gained by adjusting (bending) brace on fender well. 19. Recheck everything

Related Content:

2004 honda civic head bolt torque, 4y toyota head torque

2004 Toyota Prius EV (Electric Vehicle) Button Installation Instructions

0

Filed Under (Toyota Manuals) by admin on 31-03-2012

download
Time and Difficulty: I found the install to be moderately difficult and pretty time-consuming (about 3 hours) ; others have found it simple and report they have done it in as little as 30 minutes. Your experience will depend on your familiarity with the tools and electronics. I, personally, found insertion of the connection pin into the HV ECU plug to be difficult and almost got the first pin irrevocably stuck in the slot. I spent quite a bit of time with that part alone. I also found threading the wire behind the dash to be fairly tricky. I think the average person, not encountering any problems, could do this job in about 1-1½ hours. Procedure in Brief: 1) Remove bottom cover of steering wheel 2) Locate and unplug flasher plug 3) Open plug and remove 1-3 unused connector pins 4) Reattach steering wheel cover 5) Dismantle part of dash (vents) and remove lower glove box 6) Locate HV ECU (gray plugs) and remove lower plug 7) Solder wire to connector pin and insert into ECU plug (#27) 8) Splice EV button ground wire into ECU plug ground wire (#1) 9) Plug ECU plug back into the ECU 10) Thread wire behind dash to opening near dimmer switch 11) Attach switch to cover and solder wires in place 12) Reassemble the dash 13) Test Procedure in Detail: *Review ALL steps before proceeding and be sure you understand all terms used and you’ve looked at all diagrams and pictures. 1) Remove the bottom cover of the steering wheel by releasing the steering wheel adjustment handle and unscrewing the silver screw in that recess. 2004_prius_evv2.doc Page 4 of 20 Last updated March 13th, 2004 Then, turn the steering wheel 90 degrees right and remove the black screw that becomes visible on the right side of the steering column. Then turn the wheel 180 degrees left (90 degrees from normal position) and remove the black screw on the left side of the steering column. Carefully pull down on the lower portion of the steering column cover until it releases. Mine was a bit stiff/stuck to the upper part and you may need to carefully use a butter knife or screwdriver to start prying them apart. 2004_prius_evv2.doc Page 5 of 20 Last updated March 13th, 2004 2) Locate and unplug the white flasher plug visible just on the left side of the bottom of the steering column. 3) 2 little clips keep a cover locked in place. Pull those apart and remove the cover. Inside you’ll see lines of silver connector pins–some with wires attached, some without. You should remove between 1 and 3 of those pins–2 is probably safe, 3 might be better, since if you plan to install an OEM button at some point, you’ll probably need more pins for that. (You need one pin for the procedure, but it’s handy to have a back-up.) To remove the pins, you can use your paper clip to start the process of sliding them out, and then they just pull right out. 2004_prius_evv2.doc Page 6 of 20 Last updated March 13th, 2004 Stick them to a piece of tape or put them somewhere secure so you can find them later. Snap the cover back into place, and plug the flasher plug back in. 4) Replace the steering wheel cover by reversing the process. Be sure everything’s aligned properly and that there are no gaps. 5) Now you’ll need to dismantle part of the dash to get access to the ECU and other areas. First, open the top and bottom glove box doors. Squeeze the inside sides of the lower glove box together to get the catches past the portion of the dash frame that keeps the door from falling all the way open. Then pull the entire door straight toward you – it will unclip from the hinges at the bottom of the glove box. 2004_prius_evv2.doc Page 7 of 20 Last updated March 13th, 2004 You may also need to unclip the little hydraulic piston that keeps the door from falling open too quickly. Next, grasp the bottom of the silver vent piece next to the glove box. Pull it toward you firmly. It should unclip at the bottom first. Then pull the whole unit straight out

Related Content:

2004 Sienna Fuse Box Diagram, 2004 Chevrolet Malibu Classic Manual Free, 2004 suburban sunroof problems, 2004 honda crv repair manual pdf, all air vents open on 2004 ford explorer, exploded view pontiac grand prix ac system, exhaust system for 2004 malibu maxx lt, 2004 sienna thermostat replacement, 2004 mazda 3 headlight adjustment, how to reset computer on 2004 chevy impala

TOYOTA BLOCK HEATER APPLICATION INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 20-06-2011

download
Remove oxygen sensor wire connector & clamp. Remove exhaust manifold & drain coolant. Remove installation hole cover & 2 studs. Remove original silicone sealant from hole. Clean hole surfaces. Secure heater in position with the bracket, bolts & lock washers provided. Connect cordset. Route cordset through opening between right side of bumper & engine under-cover. For Avalon, route cordset through opening beside right side of radiator and under right headlight. Secure cordset to the A/C suction pipe. Replace engine components removed earlier. Refill coolant, run engine & check for leakage & coolant level. 3 AVALON 2005- 2010 2GR-FE PU140-00900 PU140- 03571 Rear, L.H.S. (hole direction pointing to front) Route cord up. Tie the cord to the lower heater hose outlet. Route the cord to left side of engine. Tie the cord to the main harness besides the fuse box. Remove front radiator plastic cover. Route the cord down on left side of battery and tie the cord to the left side of radiator coolant fan harness at the front bottom of the battery. Route the cord to the front and tie to the front grille. 11 1983- 86 2SE C0140-00123* C0140- 00069 Front L.H.S. 2nd from transmission 6 1987- 91 3S-FE C0140-00134* C0140- 00070 Rear 2nd from right 12 1988- 91 2V-ZFE C0140-00110* C0140- 00767 Front centre. Loosen union bolt of water outlet five revolutions before refilling coolant. Tighten after coolant fill. 12 1992- 93 3VZ-FE C0140-01141* C0140- 00903 Front 1st from left. Remove exhaust manifold; remove exhaust pipe if necessary. Route cordset towards the left side of engine compartment. 6 1992- 2001 5S-FE C0140-01123* C0140- 02899 Front, 2nd from left. Remove exhaust manifold. For models prior to 1994 model year, remove upper exhaust manifold heat shield only. Route cordset towards left side of engine compartment. 12 CAMRY 1994- 2006 IMZ-FE C0140-00644* C0140- 02897 Front, R.H.S. Remove oxygen sensor wire connector & clamp. Remove exhaust manifold & drain coolant. Remove installation hole cover & 2 studs. Remove original silicone sealant from hole. Clean hole surfaces. Secure heater in position with the bracket, bolts & lock washers provided. Connect cordset. Route cordset through opening between right side of bumper & engine under-cover. For Avalon, route cordset through opening beside right side of radiator and under right headlight. Secure cordset to the A/C suction pipe. Replace engine components removed earlier. Refill coolant, run engine & check for leakage & coolant level

Related Content:

2008 camry how to eemove enine, 2gr-fe manual

Related Content:

ford 5 4L water jacket leak spark plug hole intake gasket, 2001 ford excursion water leak on back of motor, metal mesh hanging loose under escort zx2, volvo d12 exhaust manifold bolt torque, replace a front exhaust manifold 2004 ford escape 24 valve, isuzu npr 5 7 water pump bolt torque, schematic of a 2005 chrysler exhaust system, volvo penta 125 exhaust manifold bolt torques, what parts are required to replace the exhaust from the manifold on back for a 1990 ford f150, intake manifold leak sound