Skip to content

how to replace the throttle body sensor 2007 kia sorento

You search PDF repair manual about how to replace the throttle body sensor 2007 kia sorento, if there are search results will appear below. If search results do not exist, please search by others keyword.

Kia Sorento/ Sedona Throttle Position Sensor W/ 3.5L Engine (Fuel System) Service Procedure

download
Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly. Adjustment will be required. Re-install electrical connector to TP Sensor. 4. Install Global Diagnostic System. a. Select “System Option” b. Select “Idle RPM Adjust Mode” c. Apply Parking Brake 5. Select Neutral position and place engine in idle condition with A/C OFF. 6. Remove rubber plug and adjust using instructions provided on screen. Set Base idle between 800~900 rpm Adjust TPS: 7. Using the GDS scan tool, monitor current data using two (2) parameters: • Closed Throttle Position Switch • Throttle Position Voltage Value 8. Open throttle by hand very slowly until idle switch status switches to OFF. Note the TPS voltage value. Voltage:____________________________ 9. Close throttle and record the TPS voltage. oltage:____________________________ Closed throttle voltage should be 30~65mV less than the voltage noted in step eight (8). Adjust TP Sensor and repeat test as required. WARRANTY CLAIM INFORMATION: 10. Tighten TP Sensor screws as required. Torque is 12~18 inch lbs. Verify switching of throttle switch with throttle plate movement. 11. Install engine cover. 12. Clear any stored DTC which may have set during service procedure. Remove GDS tool from vehicle

2007-2010 Toyota Tundra Intake Kit Installation Instructions

download
Complete kit with parts. Step 1 Install trim seal provided to auxilary on side. Install filter adaptor to new housing with button head screws provided and secure. Install new housing using screws and grommets from step 5. Step 6 Place air filter into housing and tighten using 5/16″ nut driver. Step 11 Complete stock intake. Step 2 With couplers and clamps provided, place onto new intake tube and install. Make sure 4-1/4″ coupler is on filter side and 3-1/2″ coupler is on throttle body side. Step 7 With button head screws provided tighten down housing cover with 5/32″ allen key. Re-Install engine cover. Step 12 Lift up and remove engine cover. Step 3 Remove MAF sensor from OE air box using phillps screwdriver. Re-install to new aFe tube with hardware provided (make sure gasket and nylon spacers are between tube and sensor) using flat head screwdriver.Install brass hose fitting. Step 8 Your installation is now complete. Check all clamps and hoses periodically. Thank you for choosing aFe! Step 13 With 5/16″ nut driver loosen both clamps on OE intake tube. Remove crankcase and vacuum line away from tube. Disconnect MAF sensor harness & remove. Step 4 Tighten clamps with 5/16″ nut driver. Take out OE crankcase line and replace with 1/2″ hose and clamp provided. Step 9 With 12mm socket with extension, loosen the 3 bolts and remove the OE air box out of vehicle. Note: Save 3 bolts and grommets for later install. Step 5 Connect 1/2″ hose to new tube and tighten clamp with flathead screwdriver. Re-connect MAF sensor harness and fuel regulator.

2005 Chevrolet Colorado Pickup SES Light Due to DTCs P0105, P0106, and/ or P0506 – Clean Throttle Body

download
Models: 2004-2007 Buick Rainier 2002-2007 Chevrolet TrailBlazer 2004-2007 Chevrolet Colorado 2002-2007 GMC Envoy 2004-2007 GMC Canyon 2002-2004 Oldsmobile Bravada 2006-2007 HUMMER H3 2005-2007 Saab 9-7X with any of the following engines: 2.8L (VIN 8 – RPO LK5) 2.9L (VIN 9 – RPO LLV) 3.5L (VIN 6 – RPO L52) 3.7L (VIN E – RPO LLR) 4.2L (VIN S – RPO LL8) The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI. Condition/Concern: On rare occasions, a SES light may be experienced due to DTCs P0105, P0106, and/or P0506. There may or may not be an idle complaint accompanying the SES light. This may be due to excessive carbon build up in the throttle body. Recommendation/Instructions: If the SI diagnostics do not isolate a cause for this concern, clean the throttle body bore and plate for evaluation.

2007 TOYOTA TUNDRA COLD AIR INTAKE Preparation

download
1. Check Box Contents (a) Check box for contents and/or damage. 2. Vehicle Preparation (a) Open vehicle hood. (b) Use blankets or covers to protect the front grille and passenger-side front fender area. Note: For 5.7L installation proceed to next step. For 4.7L installation proceed to step #4 3. Removal Procedure: 5.7L V8 OE Air Inlet System (a) Raise the front of the engine cover to detach the 2 pins (Fig. 3-1). (b) Remove the 2 engine cover hooks from the bracket, and remove the cover (Fig. 3-1). (c) Disconnect the vacuum hose and ventilation hose (Fig. 3-2). (d) Loosen the two 10 mm hose clamps and remove the air cleaner hose (Fig. 3-2). 12 mm Wrench Fig. 3-1 Fig TOYOTA TUNDRA 2007 – COLD AIR INTAKE Procedure Page 3 of 15 pages Issue: A 08/24/07 10mm Socket 10 mm Socket 10 mm Socket 4. Removal Procedure: 4.7L V8 OE Air Inlet System (a) Remove the two 10 mm cap nuts and throttle body cover (Fig. 4-1). (b) Remove air cleaner hose assembly. (1) Disconnect the vacuum hose and No. 2 ventilation hose (Fig. 4-2). (2) Loosen the two 10 mm hose clamps and remove the air cleaner hose (Fig. 4-2). 5. Removal Procedure: 5.7L and 4.7L V8 OE Air Inlet System (a) Remove the air cleaner lid. (1) Disconnect the MAF sensor connector (Fig. 5-1). (2) Using a clip remover, detach the wire harness clamp (Fig. 5-1). (3) Unfasten the 4 hook clamps and then remove the air cleaner lid (Fig. 5-1). (b) Remove OE air filter and save. (c) Remove the two 10 mm bolts and air cleaner case (Fig. 5-2)

1998-2000 ISUZU RODEO/AMIGO HIGH/ERRATIC IDLE CONDITION SERVICE MANUAL

download
1998 – 2000 MODELS 1. Inspect main ground points (refer to SB99*04*S001 for more information). * P6 ground point-body [on the passenger side of engine compartment, between the battery and cruise control actuator (if equipped)]. (Figure Fig. 1 ) * P10 ground point-engine (at the alternator bracket) . (Figure Fig. 2 ) Isuzu: 1998 – 2000 Rodeo AFFECTED VEHICLES:1998 – 2000 Rodeo (UE)/Amigo (UA) models with 3.2L V6 engines NOTE: Please refer to the appropriate workshop manual for the correct diagnosing procedure and/or follow the service procedures outlined in this bulletin for the vehicle being serviced. NOTE: The 1998, 1999 or 2000 Rodeo/Amigo Electrical Troubleshooting Manual can assist in locating the vehicle ground distribution (i.e., ground contact points). * Perform a voltage drop test at the main ground points. * If the voltage drop test fails, then inspect and clean both the bolt and contact point. * Verify and correct idle settings (if needed) as described in the workshop manual. * If the repair procedure on this step solves the high idle condition, then return the vehicle to the customer. If the repair procedure on this step does not solve the high idle condition, then go to step 2 (16 pin Blue Connector). B. Remove P-6/P-10 ground terminal and bolt for ground contact inspection. * Inspect ground contact area for corrosion. * Inspect bolt and thread for damage or corrosion. * Clean the ground area and fastening bolt thoroughly with a wire brush. * Replace bolt if damaged or heavily corroded. C. Install the P-6/P-10 ground terminal and bolt (tighten using hand tools only). * Torque the P-6/P-10 ground terminal bolt to (14 N.m) 10 lb.ft. 1998 – 1999 MODELS ONLY 2. Inspect the 16 pin blue connector, located under the power steering fluid reservoir for corrosion, bent, or damaged pins (specifically for the Throttle Position Sensor). (Figure Fig. 3 )