Skip to content

how to replace the throttle position sensor on a 2003 kia sedona

You search PDF repair manual about how to replace the throttle position sensor on a 2003 kia sedona, if there are search results will appear below. If search results do not exist, please search by others keyword.

Kia Sorento/ Sedona Throttle Position Sensor W/ 3.5L Engine (Fuel System) Service Procedure

download
Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly. Adjustment will be required. Re-install electrical connector to TP Sensor. 4. Install Global Diagnostic System. a. Select “System Option” b. Select “Idle RPM Adjust Mode” c. Apply Parking Brake 5. Select Neutral position and place engine in idle condition with A/C OFF. 6. Remove rubber plug and adjust using instructions provided on screen. Set Base idle between 800~900 rpm Adjust TPS: 7. Using the GDS scan tool, monitor current data using two (2) parameters: • Closed Throttle Position Switch • Throttle Position Voltage Value 8. Open throttle by hand very slowly until idle switch status switches to OFF. Note the TPS voltage value. Voltage:____________________________ 9. Close throttle and record the TPS voltage. oltage:____________________________ Closed throttle voltage should be 30~65mV less than the voltage noted in step eight (8). Adjust TP Sensor and repeat test as required. WARRANTY CLAIM INFORMATION: 10. Tighten TP Sensor screws as required. Torque is 12~18 inch lbs. Verify switching of throttle switch with throttle plate movement. 11. Install engine cover. 12. Clear any stored DTC which may have set during service procedure. Remove GDS tool from vehicle

2003 Honda ODYSSEY Intake Manifold Removal and Installation Manual

download
Removal 1. Remove the intake manifold cover (A) and ignition coil cover(s) (B). 1999-2001 models: 2002-2004 models: 2. Remove the evaporative emission (EVAP) canister hose (A) (1999-2001 models) or vacuum hose (A) (2002-2004 models). 3. Remove the vacuum hose(s) (B) and breather pipe (C), then remove the intake air duct (D). 1999-2001 models: 2002-2004 models: 4. Remove the throttle cable (A) and cruise control cable (B) by loosening the locknuts (C), then slip the cable ends out of the accelerator linkage. Take care not to bend the cables when removing them. Always replace any kinked cable with a new one. 5. Remove the engine wire harness connectors and wire harness clamps from the intake manifold. *Intake air temperature (IAT) sensor connector *Idle air control (IAC) valve connector *Throttle position (TP) sensor connector *Manifold absolute pressure (MAP) sensor connector *Evaporative emission (EVAP) canister purge valve connector (2002-2004 models) 6. Remove the brake booster vacuum hose (A) and positive crankcase ventilation (PCV) hose (B). 7. Remove the vacuum hoses (C) (1999-2001 models). 1999-2001 models: 2002-2004 models: 8. Remove the breather hose (A) and water bypass hoses (B), then plug the water bypass hoses. 9. Remove the EVAP canister hose (C) (2002-2004 models). 1999-2001 models:

2000-2002 Toyota Corolla, Celica, MR2 Spyder, and ECHO DTC P1349 – VVTi ACTUATOR Repair Manual

download
TC P1349 – VVTi ACTUATOR – EG009-03 May 19, 2003 Page 3 of 4 1. Inspect the condition of the valve cover oil baffle as per TSB EG007-02. If camshaft or camshaft position sensor damage resulting from a bent baffle is identified, repair the damage as necessary. 2. Make sure the vehicle is in “PARK” with the engine idling. 3. Referring to the screen flow below, connect the Toyota Diagnostic Tester to the vehicle and select the VVT Control Bank One Active Test (VVT CTRL B1) from the Active Test Menu. 1: DATA LIST 2: DTC INFO 3: 4: SNAPSHOT 5: SYSTEM CHECK 6: RESET MEMORY 7: MONITOR INFO 8: CHECK MODE SELECT DATA B DIAGNOSTIC MENU ENGINE A C INJ VOL A/F CONTROL CAN CTRL VSV TANK BYPASS VSV EVAP VSV (ALONE) A/C MAG CLUTCH FUEL PUMP/SPD LINE PRESS UP VVT CTRL B1 Confirm that the Vehicle is Stopped And Engine Idling 3: ACTIVE TEST PRESS [ENTER] INJECTOR 3.5ms IGN ADVANCE 11.0deg CALC LOAD 22% MAF 3.68gm/s ENGINE SPD 684rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.82V AFS B1 S1 3.25V SHORT FT #1 1.5% LONG FT #1 5.4% TOTAL FT #1 1.08 E D VVT CTRL B1 OFF INJECTOR 8.3ms IGN ADVANCE 5.0deg CALC LOAD 0% MAF 0.00gm/s ENGINE SPD 0rpm COOLANT TEMP186.8F INTAKE AIR 129.2F THROTTLE POS 14% CTP SW ON VEHICLE SPEED0MPH O2S B1S2 0.33V AFS B1 S1 3.29V SHORT FT #1 -0.1% LONG FT #1 5.4% TOTAL FT #1 1.08 VVT CTRL B1 ON 4. Using the right arrow key, toggle the VVTi actuator “ON.” 5. If at this point the vehicle does not run rough and/or stalls when the active test is performed, proceed with Repair Manual P1349 VVTi Fault Isolation Procedure (FIP). If the vehicle does stall and/or runs rough, this indicates the the VVTi control system is operating. Proceed to replace the VVTi actuator following the repair procedures listed on the Technical Information System (TIS): Engine Mechanical Section, Camshaft, Replacement The camshaft timing gear should come in the unlocked position from the factory. If it is difficult to install the camshaft timing gear, the lock pin may be engaged. To disengage the lock pin, apply and hold approximately 20 psi of air pressure at the oil feed hole located 90 degrees clockwise of the oval slot. (See Figure 1.) Once the pin has released, turn the interior assembly counterclockwise. (See black arrow in Figure 1.) B. Put the camshaft timing gear assembly and the camshaft together with the straight pin off the key groove. C. Turn the camshaft timing gear assembly (as shown in Figure 2) while pushing it lightly against the camshaft. Push further at the position where the pin fits into the groove. NOTE: Be sure not to turn the camshaft timing gear to the retard angle side (in the clockwise direction). D. Check that there is no clearance between the end of the camshaft and the camshaft timing gear. E. Tighten the camshaft bolt with the camshaft timing gear fixed. Torque: 54 Nm (551 kgfcm, 40 ftlbf) F. Check that the camshaft timing gear assembly can move to either side and is not locked

2003 Ford Truck Expedition Suspension – Air Suspension Height Sensor Linkage Loose Service Procedure

download
ISSUE Some 2003-2006 Expedition and Navigator vehicles equipped with an air suspension may exhibit an air suspension height sensor linkage arm disengaging from the suspension ball stud or height sensor rotating arm. This concern typically occurs with the rear sensor (Figure 1) but may occur with the front sensors as well. If this occurs, the symptom will typically be the vehicle leaning to one side, the vehicle sitting too low/high, a harsh ride, and/or an inoperative air suspension. In addition, this concern may result in diagnostic trouble code (DTC) C1725 (air suspension front pneumatic failure) or C1726 (air suspension rear pneumatic failure). ACTION When a linkage arm becomes disengaged, do not re-attach the arm and do not replace the sensor unless broken. Instead, install a revised linkage arm on all three (3) sensor assemblies, even if they have not detached from the ball stud. 1. Replace linkage arms on all three (3) sensor assemblies following Workshop Manual (WSM), Section 204-05. 2. Discard the old linkage arms. NOTE IF THE SENSOR ASSEMBLY NEEDS TO BE REPLACED FOR ANY DAMAGE/FAILURE OTHER THAN THE ONE DESCRIBED IN THIS TSB, THE REPLACEMENT ASSEMBLY IS SUPPLIED WITH A NEW STYLE LINKAGE ARM, SO THERE IS NO NEED TO ORDER ADDITIONAL LINKAGES FOR THE SERVICE REPAIR. WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage OPERATION DESCRIPTION TIME 061510A 2003-2006 0.4 Hr. Expedition/Navigator: Replace The Three Linkage Arms, Includes Time To Check Diagnostic Trouble Codes (Do Not Use With 5300A, 5300A7, 5300A8) DEALER CODING CONDITION BASIC PART NO. CODE 5A967

2001 Chevrolet Chevy K Silverado Crankshaft Position Sensor Engine Stall Service Procedure

download
Why is your vehicle being recalled? Your vehicle may have a condition in which the crankshaft position sensor can fail intermittently or permanently. If the sensor fails intermittently, the Service Engine Soon (SES) light may illuminate and the vehicle may run rough. In addition, the engine may stall, and if so, may re-start immediately or after a cool down period. If the sensor fails permanently, the engine will quit running and will not re-start. If this happens while the vehicle is moving, a crash could result without prior warning. What will we do? Your GM dealer will replace the crankshaft position sensor. This service will be performed for you at no charge . Because of service scheduling requirements, it is likely that your dealer will need your vehicle longer than the actual service correction time of approximately one hour and twenty minutes. What should you do? You should contact your GM dealer to arrange a service appointment as soon as possible. Bring the enclosed customer reply form with you when you visit your dealer. The form identifies the repairs required. If you no longer own this vehicle, please let us know by completing the form and mailing it back to us. Did you already pay for this repair? The enclosed form explains what reimbursement is available and how to request reimbursement if you have paid for repairs for the recall condition.