Skip to content

how to replace the vent control valve hyundai santa fe

You search PDF repair manual about how to replace the vent control valve hyundai santa fe, if there are search results will appear below. If search results do not exist, please search by others keyword.

2005 Hyundai Truck Santa Fe TRANSAXLE/ ATA SOLENOID DIAGNOSTIC REPAIR MANUAL

download
Subject: ATA SOLENOID DIAGNOSTIC CODES P0740, P0741, P0742, P0743, P0746, P0748, P0750, P0755, P0760, P0765, P0770 This TSB supersedes TSB # 05-40-006 to include DTC descriptions in Step 10. DESCRIPTION: Incorrect operation of the transaxle solenoids may result in the following three symptoms: REPAIR PROCEDURE: 1. Check Engine Light illuminated 2. Transaxle held in 3rd gear “Fail-safe” 3. Diagnostic Trouble Codes P0740, P0741, P0742, P0743, P0746, P0748, P0750, P0755, P0760, P0765 or P0770 set. NOTE: Do NOT replace the transaxle for solenoid codes listed as open/short. Instead, follow the repair procedure shown below. 1. Using a Hi-Scan Pro, check for DTC in both the “Engine” and “Automatic Transaxle” menus. Record the DTC and description. 2. From the Hi-Scan Pro, select: ^”Hyundai Diagnosis” menu ^”Vehicle ^”Auto Transaxle” menu ^”Actuation Test” ^Press the F1 button (STRI) and test the LR, UD, 2ND, OD, DCC and FSV solenoid (if applicable). Monitor the Hi-Scan and listen for a solenoid sound from the engine compartment. ^If Hi-Scan shows: ^”TEST FAILURE” and no solenoid sound is heard, go to Step 3. ^”COMPLETED” and solenoid sound is heard, the wiring between the PCM/TCM has no open or short circuits. Go to Step 5. 3. Visually check the wiring harness between the TCM and transaxle for a damaged wire or a short circuit to ground. Disconnect the connectors to the solenoids at the transaxle and the PCM/TCM and check for a bent pin or a pin not fully inserted into the connector. If so, repair or replace the ECM control harness, P/N 914XX-XXXXX 4. Check the harness inside the transaxle oil pan for a short circuit to ground. Replace the harness if damage is found or if three or more solenoid DTCs are found in Step 1. (Refer to TSB # 04-40-015 for instructions). Zoom Sized for Print 5. Refer to the DTC recorded in Step 1 and follow the repair procedure shown. SOLENOID REPLACEMENT: 6. Remove the battery. 7. Drain the radiator. Remove the lower radiator hose from the radiator. 8. Drain the ATF. 9. Remove the valve body cover from the transaxle

DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Check Engine Light On (Replace Evaporative Emission (EVAP) Vent Valve Solenoid Assembly and Add/Relocate Filter Box Using Service Kit)

download
Tighten Tighten the bracket mounting bolt to 12 N?m (106 lb in). Connect the vent valve pipe to the EVAP canister. • Install the two vent valve pipe clips into the existing underbody holes. • Connect the EVAP canister vent valve electrical connector, if equipped. • Attach bulk 5/8″ heater hose to the vent valve port and secure using a clamp. Run a length as needed along the frame rail routing to the area above the transmission. • Cut the hose to determined length and install the supplied filter box. Secure using a clamp. • Remove the transmission support and lower the transmission assembly as necessary to allow for access to the new filter box location using a tie strap. DO NOT pinch or restrict the transmission vent hose. The filter box opening should be pointing downward. • Raise the transmission and reinstall the transmission support. • Tie strap the hose as needed along the frame rail in order to keep the hose away from pinch*points and heat sources. • Lower the vehicle. • 2004-2007 Model Year (Use Service Kit P/N 19152349) Raise the vehicle. Suitably support the vehicle. • Disconnect the EVAP canister vent valve electrical connector. • Disconnect the canister pipe from the vent valve. • Push in the retainer and remove the existing canister vent valve from the fuel tank clip or mounting bracket. Discard the old valve. • Cut back the existing canister pipe approximately 51 mm (2 in) to remove the quick connect end. Crew Cab Short Box Shown Below, Other Configurations Similar Extended Cab Short Box Shown Below, Other Configurations Similar Install the new canister vent valve to the fuel tank clip or mounting bracket. • Cut bulk 5/8″ heater hose to a length of approximately 76 mm (3 in). Install the hose between the vent valve and the canister pipe and secure using clamps. • Attach bulk 5/8″ heater hose to the vent valve port and secure using a clamp. Run a length as needed along the frame rail routing to the area above the transmission. • Cut the hose to determined length and install the supplied filter box. Secure using a clamp. •

2004 Chevrolet Chevy K Silverado – 4WD Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup

download
Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip from the canister vent solenoid (CVS) line. 3. Disconnect the CVS electrical connector. 2004 Chevrolet Chevy K Silverado – 4WD 4. If the vehicle is equipped with a 6 ft box, disconnect the EVAP CVS line from the canister. 5. Remove the CVS clip from the frame crossmember. 6. Push in the retainer and remove the CVS from the fuel tank clip. 7. If the vehicle is equipped with a 8 ft box, disconnect the EVAP CVS line from the canister. 8. Remove the CVS clip from the frame crossmember. 9. Push in the retainer and remove the CVS from the fuel tank clip. Installation Procedure 1. If the vehicle is equipped with a 8 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 8 ft box, the CVS line is routed below the frame crossmember. 2. Install the CVS clip to the frame crossmember. 3. Connect the EVAP CVS line to the canister. 4. If the vehicle is equipped with a 6 ft box, install the CVS to the fuel tank until the clip engages. Important On vehicles equipped with a 6 ft box, the CVS line is routed above the frame crossmember. 5. Install the CVS clip to the frame crossmember. 6. Connect the EVAP CVS line to the canister. 7. Connect the CVS electrical connector. 8. Install the harness clip to the canister vent solenoid (CVS) line. 9. Lower the vehicle.

2008 Ford Focus A/T Main Control Valve Body Removal And Installation

download
Disassembly 12 7Z490 Separator plate and gasket assembly 1. Remove the solenoid body bolts and the 13 7A101 Body — control valve lower solenoid body. 14 7R294 Stop — main regulator valve 15 7F445 Retainer plate — main regulator valve 16 7A270 Spring — main fluid pressure regulator valve 17 7C338 Valve — main fluid pressure regulator 18 7G411 Spring — solenoid regulator valve 19 7H392 Valve — solenoid regulator valve 20 7D400 Spring — intermediate servo accumulator 21 7D398 Piston — intermediate servo 2. Remove and discard the solenoid body gaskets. accumulator 22 7G408 Valve — converter pressure relief 23 7G316 Spring — converter regulator valve 24 7M040 Valve — lock up control 25 7Z490 Gasket — solenoid body 26 7G179 Valve — low reverse shift 27 7M040 Valve — 3-4 shift 28 7H148 Shift Solenoid B (SSB) (on/off) valve 29 7H148 Shift Solenoid A (SSA) (on/off) valve ISASSEMBLY AND ASSEMBLY (Continued) 3. Remove and discard the seals. 3. Install the seals. 4. Disassemble the main control valve body. 4. Install a new solenoid body gasket. Assembly 1. Install a new separator plate and gasket assembly. 2. NOTE: Do not fully tighten the bolts at this stage. Assemble the main control valve body and loosely install the bolts. DISASSEMBLY AND ASSEMBLY (Continued) 5. Install the solenoid body and loosely install the 6. Tighten the solenoid body bolts in the sequence bolts. shown. •Tighten to 9 Nm (80 lb-in)

2001 Hyundai Accent 1.5L Difficulty filling the gas tank The pump keeps clicking off Repair Manual

download
Tests/Procedures: 1. Disconnect the vapor line at the charcoal canister that comes from the liquid vapor separator and goes to the charcoal canister. See if the fuel tank can be easily filled then. 2. If the fuel tank can easily be filled with the vapor line removed from the charcoal canister, reconnect the vapor line and remove the other lines from the charcoal canister and see if the fuel tank can be easily filled. 3. If the fuel tank is once again difficult to fill, replace the charcoal canister. 4. If disconnecting the vapor line at the charcoal canister does NOT make the fuel tank easy to fill, then disconnect the vapor line from the liquid vapor separator at the fuel tank in case the vapor line is plugged/restricted. Potential Causes: Charcoal Canister Liquid Vapor Separator Vapor Line Tech Tips: Fuel vapors are directed to the canister from the ORVR fill vent valve in the gas tank through the liquid vapor separator and to the canister. The metal tube that loops up by the filler neck is part of the vapor line to the canister