Skip to content

how to replace toyota 2007 camry front grille

You search PDF repair manual about how to replace toyota 2007 camry front grille, if there are search results will appear below. If search results do not exist, please search by others keyword.

2007-2010 Toyota Camry Hybrid Vehicles Potential Floor Mat Interference with Accelerator Pedal

download
The owner notification will commence in early February, approximately one week after your dealership has been notified. This campaign will be launched in phases. • The first phase will include certain 2007 through 2010 model year Camry and Camry Hybrid vehicles equipped with Denso accelerator pedals. These owner letters will be mailed over a period of several weeks. • Additional models, including Camrys equipped with a CTS accelerator pedal will be launched in later phases as the remedy is developed. • Information on additional phases related to Camry (equipped with a CTS accelerator pedal), Avalon, Corolla, Highlander, Matrix, Prius, Tacoma, Tundra and Venza will be provided prior to the launch of these phases. If your dealership is contacted by an owner of a Denso pedal equipped Camry who has not yet received a notification, please verify eligibility by confirming through Dealer Daily/TIS prior to performing repairs . Dealers should perform the repair as outlined in the attached Technical Instructions. 2. Vehicles in Dealer Stock • As required by Federal law, dealers are not to deliver any new vehicles in their inventory, which are involved in a safety recall unless the defect has been remedied. However, because this defect does not exist in vehicles in which the driver’s side floor mat is compatible with the vehicle and properly secured you may continue to sell new vehicles (with Denso pedals) that have not received the full remedy if you assure the driver’s position floor mat is semi-permanently secured or place the front driver’s and passenger’s floor mats in the trunk on any vehicles in stock prior to sale or lease. Vehicle safety recall completion can be verified through TIS. • In order to assure established customers receive priority for the safety recall, we request that this campaign remedy be performed on in-stock Camry and Camry Hybrid vehicles just prior to vehicle delivery where possible. • A VIN list containing vehicles in dealer stock will be provided shortly

2007 TOYOTA TUNDRA W/ Tracks Deuce Installation Manual

download
Remove cargo rail end plugs: At the tailgate push in on the plug lock and at the same time push the end plug out of the track. 2 Next remove tie downs: If tie down are installed remove them from the cargo rail. 3 1 3 2 4 4 Install clamps in cargo rail as shown below: After clamps and tie downs are installed replace the cargo rail end plugs. Leave clamps loose for now. Next repeat steps 1 through 4 for the passenger side clamp installation. 5 Tailgate end Position clamp here Front of box Position tie down here Position clamp here Position clamp here Position tie down here Position clamp here Four clamps per side needed. Continue with step 8 in the main Deuce manual. 2007 TOYOTA TUNDRA W/TRAcks DeUce INsTALLATION INsTRUcTIONs Install Deuce Rail: With the tailgate closed, position the TruXedo rail along the inside edge of the truck box. Compress the rear seal against the tailgate as shown. Tighten clamps against the rail. See step seven for proper clamp height. leave clamps loose for now 7 Tighten clamp assemblies securely on side rails before driving vehicle. ! The TruXedo rail will be positioned at this height. Clamp height is correct at this setting. Next install the front striker bracket: From one end of the front cargo rail remove the plastic insert plug. Next slide the striker bracket assembly into the cargo rail. See step nine for additional information

2007 Toyota Camry Billet Bumper Grille Installation Instructions

download
Step 1: Remove the 2 screws that hold the top portion of the front fascia to the core support. Figure 1 Step 2: Remove the 2 push clips that hold the top portion of the front fascia to the core support. Figure 2 Figure 1 Figure 2 Step 3: Remove the bolt that holds the center of the front fascia to the core support. Figure 3 Step 4: Rock the top portion of the front fascia forward to gain access to the backside of the factory grille shell. Step 5: There are 16 clips that hold the factory grille shell and most should come undone by pulling out on the grille shell, some of them may need to be unclipped from the backside and then remove the factory grille shell from the front fascia. Figure 4 Step 6: Install the fully threaded studs into the threaded tabs on the backside of the billet grille. Step 7: Center the billet grille into the bumper opening. Step 8: Coming in through the factory grille shell opening install the powder coated brackets over the fully threaded studs and hold in place using the k-lock nuts. Figure 5. The photo was taken without the grille being installed. The grille must first be installed onto the vehicle then the powder coated brackets placed over the fully threaded studs. Figure 5 Step 9: Re-center the billet grille to your liking and secure all hardware. Step 10: If you are installing part# 807196 now is the time to do so. Step 11: Reattach the front fascia to the vehicle using the hardware saved from steps

2007 TOYOTA TUNDRA COLD AIR INTAKE Preparation

download
1. Check Box Contents (a) Check box for contents and/or damage. 2. Vehicle Preparation (a) Open vehicle hood. (b) Use blankets or covers to protect the front grille and passenger-side front fender area. Note: For 5.7L installation proceed to next step. For 4.7L installation proceed to step #4 3. Removal Procedure: 5.7L V8 OE Air Inlet System (a) Raise the front of the engine cover to detach the 2 pins (Fig. 3-1). (b) Remove the 2 engine cover hooks from the bracket, and remove the cover (Fig. 3-1). (c) Disconnect the vacuum hose and ventilation hose (Fig. 3-2). (d) Loosen the two 10 mm hose clamps and remove the air cleaner hose (Fig. 3-2). 12 mm Wrench Fig. 3-1 Fig TOYOTA TUNDRA 2007 – COLD AIR INTAKE Procedure Page 3 of 15 pages Issue: A 08/24/07 10mm Socket 10 mm Socket 10 mm Socket 4. Removal Procedure: 4.7L V8 OE Air Inlet System (a) Remove the two 10 mm cap nuts and throttle body cover (Fig. 4-1). (b) Remove air cleaner hose assembly. (1) Disconnect the vacuum hose and No. 2 ventilation hose (Fig. 4-2). (2) Loosen the two 10 mm hose clamps and remove the air cleaner hose (Fig. 4-2). 5. Removal Procedure: 5.7L and 4.7L V8 OE Air Inlet System (a) Remove the air cleaner lid. (1) Disconnect the MAF sensor connector (Fig. 5-1). (2) Using a clip remover, detach the wire harness clamp (Fig. 5-1). (3) Unfasten the 4 hook clamps and then remove the air cleaner lid (Fig. 5-1). (b) Remove OE air filter and save. (c) Remove the two 10 mm bolts and air cleaner case (Fig. 5-2)

2006-2009 Toyota Camry Harsh 5-4 Downshift on Deceleration Repair Manual

download
Harsh 5-4 Downshift on Deceleration Repair Procedure 1. Test drive and verify that the 5-4 harsh downshift condition occurs as described in the Introduction section in this TSB. 2. Replace the SLT solenoid assembly. Refer to the Technical Information System (TIS): •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” •2007 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2008 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” •2009 modelyearCamry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Re moval, Dis ass embly, Ins pec ti on, Re ass embly” NOTE For SLTsolenoid identification, refer to TSB No. TC 007-05, “U250E Transmission Solenoid Identification”. 3. Reinstall the automatic transaxle oil pan. Refer to TIS: •2006 modelyearCamry Repair Manual: Drivetrain -AutomaticTransmission/Transaxle-”Transmission ValveBodyAssy (U 250E) : Replacement” • 2007 / 2008 / 2009 model year Camry Repair Manual: Drivetrain -Automatic Transmission/Transaxle: Unit Repair -”U250EAutomatic Transaxle: Shift Solenoid Valve: Installation” 4. Test drive and verify that the A TM operates normally