Skip to content

how to replace turn signal switch in chevy impala 2002

You search PDF repair manual about how to replace turn signal switch in chevy impala 2002, if there are search results will appear below. If search results do not exist, please search by others keyword.

2003 Chevrolet Impala LS MULTIFUNCTION TURN SIGNAL SWITCH REPLACEMENT

download
1. Disable the SIR system. Refer to SIR Disabling and Enabling Zone 3 in SIR. 2. Remove the upper and lower trim covers. Refer to Steering Column Trim Covers Replacement . 3. Remove the wire harness assembly (1) from the wire harness strap (2). 4. Disconnect the turn signal and multifunction switch assembly connector from the SIR system coil connector. 5. Slide the 2 connectors (2) of the turn signal and multifunction switch assembly out of the bulkhead connector (1) 6. Remove the 2 pan head tapping screws (1) and (3) from the turn signal and multifunction switch assembly (2). 7. Remove the turn signal and multifunction switch assembly (2) from the steering column tilt head assembly. 1. Install the turn signal and multifunction switch assembly (2) onto the steering column tilt head assembly. 2. Screw the 2 pan head tapping screws (1) and (3) into the turn signal and multifunction assembly (2). Tighten * Tighten the top pan head tapping screw (1) to 3 N.m (27 lb in). * Tighten the side pan head tapping screw (3) to 7 N.m (62 lb in).

2002 Chevrolet Impala Radiator Air Baffle and Deflector Replacement Manual

download
Radiator Air Baffle and Deflector Replacement – Upper Removal Procedure 1. Remove the radiator air baffle retainers. 2. Tilt the rear of air baffle upward slightly. Slide the air baffle rearward in order to disengage the upper and lower clips of the air baffle from the fascia support. 3. Remove the radiator air baffle. Installation Procedure 2002 Chevrolet Impala 1. Position the radiator air baffle to the vehicle. Tilt the rear of the air baffle upward slightly. Position the upper clip of the air baffle to the lower edge of the front fascia support C-channel. 2. Slide the baffle towards the front of the vehicle in order to completely engage the upper and lower clips of the baffle onto the fascia support. 3. Align the tabs at the rear of the air baffle to the openings in the upper radiator support. 4. Install the radiator air baffle retainers.

1999 Jeep Grand Cherokee Limited AUTOMATIC TRANSMISSIONS Chrysler 45RFE Electronic Controls Repair Manual

download
INTERNAL TCM Circuit Description The TCM is reporting internal errors. Diagnostic Procedure 1. Turn ignition switch to LOCK position. Remove transmission control relay. Measure resistance between ground and relay ground circuit (Black/Yellow wire) in relay connector. If resistance is greater than 5 ohms, repair open circuit. If resistance s not greater than 5 ohms, go to next step. 2. The TCM has an internal problem and must be replaced. P0715: INPUT SPEED SENSOR ERROR Circuit Description DTC P0715 will set if an excessive change in input RPM has been detected in any gear. Possible Causes * Intermittent wiring and connector problems. * Faulty input speed sensor. * Input speed sensor circuits shorted to ground, shorted to voltage, or open. * Faulty TCM. Diagnostic Procedure 1. Place gear selector in “P” position and start engine. Using scan tool, monitor input speed sensor value. If value is less than 400 RPM, go to next step. If value is not less than 400 RPM, go to step 9. 2. Turn ignition switch to LOCK position. Install Transmission Simulator (8333). Turn ignition on. Using transmission simulator, turn rotary knob to middle (1000/3000) position. Turn INPUT/OUTPUT switch on. Using scan tool, monitor input and output speed sensor values. If input speed sensor value is 2950- 3050 RPM and output speed sensor value is 950-1050 RPM, replace input speed sensor. If speed sensor values are not as specified, go to next step. 3. Turn ignition switch to LOCK position. Disconnect TCM harness connector. Remove transmission control relay. Using fused jumper wire, jumper fused B+ circuit (Red/White wire) and transmission relay output circuit (Red wire) together at relay connector. Turn ignition on. Measure voltage between ground and input speed sensor signal circuit (Red/Black wire) at TCM harness connector. If voltage is greater than 3 volts, repair circuit for short to voltage. If voltage is not greater than 3 volts, remove jumper wire, install relay and go to next step. 4. Turn ignition switch to LOCK position. Disconnect input speed sensor harness connector. Measure resistance of input speed sensor signal circuit (Red/Black wire) between TCM and input speed sensor. If resistance is greater than 5 ohms, repair open circuit. If resistance is not greater than 5 ohms, go to next step. 5. Measure resistance of input speed sensor ground circuit (Dark Blue/Black wire) between TCM and input

2004 Honda Element EX ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) CIRCUIT HIGH VOLTAGE MANUAL

download
1. Check the engine oil level. Is the level OK? YES- Go to step 2 . NO- Adjust the engine oil to the proper level, then go to step 14 . 2. Turn the ignition switch ON (II). 3. Clear the DTC with the HDS. 4. Do the VTEC TEST in the INSPECTION MENU with the HDS. Is the result OK? YES- Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch) and the ECM/PCM. NO- Go to step 5 . 5. Check the result of step 4 . * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Failure * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) Open * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) SIG Line Open * Rocker Arm Oil Pressure Switch (VTEC Oil Pressure Switch) GND Line Open Is the test result any of the above? YES- Go to step 6 . NO- Check for poor connections or loose terminals at the rocker arm oil pressure switch (VTEC oil pressure switch). If it is OK, replace the rocker arm oil control solenoid (VTEC solenoid valve) (see step CMP SENSOR A REPLACEMENT ), then go to 14 . 6. Turn the ignition switch OFF. 7. Disconnect the rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector. 8. Check for continuity between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminals No. 1 and No. 2 Fig. 16: Checking Continuity Between Rocker Arm Oil Pressure Switch 2P Connector Terminals Courtesy of AMERICAN HONDA MOTOR CO., INC. Is there continuity? YES- Go to step 9 . NO- Replace the rocker arm oil pressure switch (VTEC oil pressure switch) (see ROCKER ARM OIL PRESSURE SWITCH (VTEC OIL PRESSURE SWITCH) REMOVAL/INSTALLATION ), then go to step 13 . 9. Turn the ignition switch ON (II). 10. Measure voltage between rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector terminal No. 1 and body ground

1997 Chevrolet Chevy K Pickup DTC P0152 HO2S Circuit High Voltage Bank 2 Sensor 1 Repair Manual

download
The number below refers to the step number on the diagnostic table. 2. This test determines if the conditions exist in order to set the DTC P0152. 3. If the HO2S (Bank 2, Sensor 1) is intrnally shorted, the HO2S (Bank 2, Sensor 1) voltage displayed on a scan tool will be over 1.0 volt (1000 mV). Important: Before clearing DTCs, use the scan tool in order to record the Freeze Frame and the Failure Records for reference. This data will be lost when the Clear DTC Information function is used. Was the Powertrain On-Board Diagnostic (OBD) System Check performed? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Connect the scan tool. 2. Run the engine at the normal operating temperature. 3. Place the vehicle in park or neutral. 4. Apply the parking brake. 5. Increase the engine speed to the specified value. Does the scan tool data display indicate HO2S sensor voltage fixed above the specified value? 1200 RPM 0.976 V (976 mV) Go to Step 3 Go to Step 4 3 1. Disconnect the HO2S. 2. Turn on the ignition while leaving the engine OFF. 3. Turn ON the ignition leaving the engine off. Does the scan tool data display indicate the HO2S voltage near the specified value? 400 mV) Go to Step 6 Go to Step 5 4 The DTC is intermittent. Are any additional DTCs set? — Go to the applicable DTC table Go to Diagnostic Aids 5 1. Check for a short to voltage in the HO2S Signal circuit. 2. If a problem is found, repair the circuit as necessary. Refer to Wiring Repairs in Electrical Diagnosis. Was the HO2S Signal circuit shorted? — Go to Step 8 Go to Step 7 6 Replace the HO2S. Refer to Heated Oxygen Sensor (HO2S) Replacement . Is the action complete? — Go to Step 8 — 7 Replace the VCM. Important: When replacing the VCM, the new VCM will need to be programed. Refer to VCM Replacement/Programming . Is the action complete? — Go to Step 8 — 1. Use the scan tool in order to select the DTC and the Clear DTC Information functions.